- 17 Sep, 2020 4 commits
-
-
Matthias Schiffer authored
[ Upstream commit 81dbbb41 ] According to the Reference Manual, the correct size is 512 MiB. Without this fix, probing the QSPI fails: fsl-quadspi 1550000.spi: ioremap failed for resource [mem 0x40000000-0x7fffffff] fsl-quadspi 1550000.spi: Freescale QuadSPI probe failed fsl-quadspi: probe of 1550000.spi failed with error -12 Fixes: 85f8ee78 ("ARM: dts: ls1021a: Add support for QSPI with ls1021a SoC") Signed-off-by:
Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Dinh Nguyen authored
[ Upstream commit 0ff5a481 ] Fixes the register address for the timer3 entry on Arria10. Fixes: 475dc86d ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC") Signed-off-by:
Dinh Nguyen <dinguyen@kernel.org> Signed-off-by:
-
Adam Ford authored
[ Upstream commit 4d26e9a0 ] Older versions of U-Boot would pinmux the whole board, but as the bootloader got updated, it started to only pinmux the pins it needed, and expected Linux to configure what it needed. Unfortunately this caused an issue with the audio, because the mcbsp2 pins were configured in the device tree but never referenced by the driver. When U-Boot stopped muxing the audio pins, the audio died. This patch adds the references to the associate the pin controller with the mcbsp2 driver which makes audio operate again. Fixes: 5cb8b0fa ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi") Signed-off-by:
Adam Ford <aford173@gmail.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Adam Ford authored
[ Upstream commit d7dfee67 ] Older versions of U-Boot would pinmux the whole board, but as the bootloader got updated, it started to only pinmux the pins it needed, and expected Linux to configure what it needed. Unfortunately this caused an issue with the audio, because the mcbsp2 pins were configured in the device tree, they were never referenced by the driver. When U-Boot stopped muxing the audio pins, the audio died. This patch adds the references to the associate the pin controller with the mcbsp2 driver which makes audio operate again. Fixes: 739f85bb ("ARM: dts: Move most of logicpd-torpedo-37xx-devkit to logicpd-torpedo-baseboard") Signed-off-by:
-
- 12 Sep, 2020 9 commits
-
-
Greg Kroah-Hartman authored
Tested-by:
Jon Hunter <jonathanh@nvidia.com> Tested-by:
Shuah Khan <skhan@linuxfoundation.org> Tested-by:
Guenter Roeck <linux@roeck-us.net> Tested-by:
Linux Kernel Functional Testing <lkft@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Roi Dayan authored
Support for phys switch id ndo added for representors and if we do not have representors there is no need to support it. Since each port return different switch id supporting this block support for creating bond over PFs and attaching to bridge in legacy mode. This bug doesn't exist upstream as the code got refactored and the netdev api is totally different. Fixes: cb67b832 ("net/mlx5e: Introduce SRIOV VF representors") Signed-off-by:
Roi Dayan <roid@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Jakub Kicinski authored
[ Upstream commit 96e97bc0 ] napi_disable() makes sure to set the NAPI_STATE_NPSVC bit to prevent netpoll from accessing rings before init is complete. However, the same is not done for fresh napi instances in netif_napi_add(), even though we expect NAPI instances to be added as disabled. This causes crashes during driver reconfiguration (enabling XDP, changing the channel count) - if there is any printk() after netif_napi_add() but before napi_enable(). To ensure memory ordering is correct we need to use RCU accessors. Reported-by:
Rob Sherwood <rsher@fb.com> Fixes: 2d8bff12 ("netpoll: Close race condition between poll_one_napi and napi_disable") Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Tetsuo Handa authored
[ Upstream commit 2a63866c ] syzbot is reporting hung task at nbd_ioctl() [1], for there are two problems regarding TIPC's connectionless socket's shutdown() operation. ---------- #include <fcntl.h> #include <sys/socket.h> #include <sys/ioctl.h> #include <linux/nbd.h> #include <unistd.h> int main(int argc, char *argv[]) { const int fd = open("/dev/nbd0", 3); alarm(5); ioctl(fd, NBD_SET_SOCK, socket(PF_TIPC, SOCK_DGRAM, 0)); ioctl(fd, NBD_DO_IT, 0); /* To be interrupted by SIGALRM. */ return 0; } ---------- One problem is that wait_for_completion() from flush_workqueue() from nbd_start_device_ioctl() from nbd_ioctl() cannot be completed when nbd_start_device_ioctl() received a signal at wait_event_interruptible(), for tipc_shutdown() from kernel_sock_shutdown(SHUT_RDWR) from nbd_mark_nsock_dead() from sock_shutdown() from nbd_start_device_ioctl() is failing to wake up a WQ thread sleeping at wait_woken() from tipc_wait_for_rcvmsg() from sock_recvmsg() from sock_xmit() from nbd_read_stat() from recv_work() scheduled by nbd_start_device() from nbd_start_device_ioctl(). Fix this problem by always invoking sk->sk_state_change() (like inet_shutdown() does) when tipc_shutdown() is called. The other problem is that tipc_wait_for_rcvmsg() cannot return when tipc_shutdown() is called, for tipc_shutdown() sets sk->sk_shutdown to SEND_SHUTDOWN (despite "how" is SHUT_RDWR) while tipc_wait_for_rcvmsg() needs sk->sk_shutdown set to RCV_SHUTDOWN or SHUTDOWN_MASK. Fix this problem by setting sk->sk_shutdown to SHUTDOWN_MASK (like inet_shutdown() does) when the socket is connectionless. [1] https://syzkaller.appspot.com/bug?id=3fe51d307c1f0a845485cf1798aa059d12bf18b2Reported-by:
syzbot <syzbot+e36f41d207137b5d12f7@syzkaller.appspotmail.com> Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by:
-
Xin Long authored
[ Upstream commit 3106ecb4 ] With disabling bh in the whole sctp_get_port_local(), when snum == 0 and too many ports have been used, the do-while loop will take the cpu for a long time and cause cpu stuck: [ ] watchdog: BUG: soft lockup - CPU#11 stuck for 22s! [ ] RIP: 0010:native_queued_spin_lock_slowpath+0x4de/0x940 [ ] Call Trace: [ ] _raw_spin_lock+0xc1/0xd0 [ ] sctp_get_port_local+0x527/0x650 [sctp] [ ] sctp_do_bind+0x208/0x5e0 [sctp] [ ] sctp_autobind+0x165/0x1e0 [sctp] [ ] sctp_connect_new_asoc+0x355/0x480 [sctp] [ ] __sctp_connect+0x360/0xb10 [sctp] There's no need to disable bh in the whole function of sctp_get_port_local. So fix this cpu stuck by removing local_bh_disable() called at the beginning, and using spin_lock_bh() instead. The same thing was actually done for inet_csk_get_port() in Commit ea8add2b ("tcp/dccp: better use of ephemeral ports in bind()"). Thanks to Marcelo for pointing the buggy code out. v1->v2: - use cond_resched() to yield cpu to other tasks if needed, as Eric noticed. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reported-by:
Ying Xu <yinxu@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Kamil Lorenc authored
[ Upstream commit a609d025 ] Keenetic Plus DSL is a xDSL modem that uses dm9620 as its USB interface. Signed-off-by:
Kamil Lorenc <kamil@re-ws.pl> Signed-off-by:
-
Paul Moore authored
[ Upstream commit d3b990b7 ] This patch fixes two main problems seen when removing NetLabel mappings: memory leaks and potentially extra audit noise. The memory leaks are caused by not properly free'ing the mapping's address selector struct when free'ing the entire entry as well as not properly cleaning up a temporary mapping entry when adding new address selectors to an existing entry. This patch fixes both these problems such that kmemleak reports no NetLabel associated leaks after running the SELinux test suite. The potentially extra audit noise was caused by the auditing code in netlbl_domhsh_remove_entry() being called regardless of the entry's validity. If another thread had already marked the entry as invalid, but not removed/free'd it from the list of mappings, then it was possible that an additional mapping removal audit record would be generated. This patch fixes this by returning early from the removal function when the entry was previously marked invalid. This change also had the side benefit of improving the code by decreasing the indentation level of large chunk of code by one (accounting for most of the diffstat). Fixes: 63c41688 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping") Reported-by:
Stephen Smalley <stephen.smalley.work@gmail.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Jens Axboe authored
[ Upstream commit de1b0ee4 ] If a driver leaves the limit settings as the defaults, then we don't initialize bdi->io_pages. This means that file systems may need to work around bdi->io_pages == 0, which is somewhat messy. Initialize the default value just like we do for ->ra_pages. Cc: stable@vger.kernel.org Fixes: 9491ae4a ("mm: don't cap request size based on read-ahead setting") Reported-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Takashi Sakamoto authored
Tascam FE-8 is known to support communication by asynchronous transaction only. The support can be implemented in userspace application and snd-firewire-ctl-services project has the support. However, ALSA firewire-tascam driver is bound to the model. This commit changes device entries so that the model is excluded. In a commit 53b3ffee ("ALSA: firewire-tascam: change device probing processing"), I addressed to the concern that version field in configuration differs depending on installed firmware. However, as long as I checked, the version number is fixed. It's safe to return version number back to modalias. Fixes: 53b3ffee ("ALSA: firewire-tascam: change device probing processing") Cc: <stable@vger.kernel.org> # 4.4+ Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20200823075537.56255-1-o-takashi@sakamocchi.jpSigned-off-by:
Takashi Iwai <tiwai@suse.de>
-
- 09 Sep, 2020 27 commits
-
-
Greg Kroah-Hartman authored
Tested-by:
-
Himadri Pandya authored
commit a092b723 upstream. The buffer size is 2 Bytes and we expect to receive the same amount of data. But sometimes we receive less data and run into uninit-was-stored issue upon read. Hence modify the error check on the return value to match with the buffer size as a prevention. Reported-and-tested by: syzbot+a7e220df5a81d1ab400e@syzkaller.appspotmail.com Signed-off-by:
Himadri Pandya <himadrispandya@gmail.com> Signed-off-by:
-
Johannes Berg authored
commit 47caf685 upstream. Reject invalid hints early in order to not cause a kernel WARN later if they're restored to or similar. Reported-by: syzbot+d451401ffd00a60677ee@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=d451401ffd00a60677ee Link: https://lore.kernel.org/r/20200819084648.13956-1-johannes@sipsolutions.netSigned-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Muchun Song authored
commit 17743798 upstream. There is a race between the assignment of `table->data` and write value to the pointer of `table->data` in the __do_proc_doulongvec_minmax() on the other thread. CPU0: CPU1: proc_sys_write hugetlb_sysctl_handler proc_sys_call_handler hugetlb_sysctl_handler_common hugetlb_sysctl_handler table->data = &tmp; hugetlb_sysctl_handler_common table->data = &tmp; proc_doulongvec_minmax do_proc_doulongvec_minmax sysctl_head_finish __do_proc_doulongvec_minmax unuse_table i = table->data; *i = val; // corrupt CPU1's stack Fix this by duplicating the `table`, and only update the duplicate of it. And introduce a helper of proc_hugetlb_doulongvec_minmax() to simplify the code. The following oops was seen: BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor instruction fetch in kernel mode #PF: error_code(0x0010) - not-present page Code: Bad RIP value. ... Call Trace: ? set_max_huge_pages+0x3da/0x4f0 ? alloc_pool_huge_page+0x150/0x150 ? proc_doulongvec_minmax+0x46/0x60 ? hugetlb_sysctl_handler_common+0x1c7/0x200 ? nr_hugepages_store+0x20/0x20 ? copy_fd_bitmaps+0x170/0x170 ? hugetlb_sysctl_handler+0x1e/0x20 ? proc_sys_call_handler+0x2f1/0x300 ? unregister_sysctl_table+0xb0/0xb0 ? __fd_install+0x78/0x100 ? proc_sys_write+0x14/0x20 ? __vfs_write+0x4d/0x90 ? vfs_write+0xef/0x240 ? ksys_write+0xc0/0x160 ? __ia32_sys_read+0x50/0x50 ? __close_fd+0x129/0x150 ? __x64_sys_write+0x43/0x50 ? do_syscall_64+0x6c/0x200 ? entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: e5ff2159 ("hugetlb: multiple hstates for multiple page sizes") Signed-off-by:
Muchun Song <songmuchun@bytedance.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Reviewed-by:
Mike Kravetz <mike.kravetz@oracle.com> Cc: Andi Kleen <ak@linux.intel.com> Link: http://lkml.kernel.org/r/20200828031146.43035-1-songmuchun@bytedance.comSigned-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Mrinal Pandey authored
commit 13e45417 upstream. The usage of "capture group (...)" in the immediate condition after `&&` results in `$1` being uninitialized. This issues a warning "Use of uninitialized value $1 in regexp compilation at ./scripts/checkpatch.pl line 2638". I noticed this bug while running checkpatch on the set of commits from v5.7 to v5.8-rc1 of the kernel on the commits with a diff content in their commit message. This bug was introduced in the script by commit e518e9a5 ("checkpatch: emit an error when there's a diff in a changelog"). It has been in the script since then. The author intended to store the match made by capture group in variable `$1`. This should have contained the name of the file as `[\w/]+` matched. However, this couldn't be accomplished due to usage of capture group and `$1` in the same regular expression. Fix this by placing the capture group in the condition before `&&`. Thus, `$1` can be initialized to the text that capture group matches thereby setting it to the desired and required value. Fixes: e518e9a5 ("checkpatch: emit an error when there's a diff in a changelog") Signed-off-by:
Mrinal Pandey <mrinalmni@gmail.com> Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Reviewed-by:
-
Alex Williamson authored
commit ebfa440c upstream. SR-IOV VFs do not implement the memory enable bit of the command register, therefore this bit is not set in config space after pci_enable_device(). This leads to an unintended difference between PF and VF in hand-off state to the user. We can correct this by setting the initial value of the memory enable bit in our virtualized config space. There's really no need however to ever fault a user on a VF though as this would only indicate an error in the user's management of the enable bit, versus a PF where the same access could trigger hardware faults. Fixes: abafbc55 ("vfio-pci: Invalidate mmaps and block MMIO access on disabled memory") Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
James Morse authored
commit 71a7f8cb upstream. AT instructions do a translation table walk and return the result, or the fault in PAR_EL1. KVM uses these to find the IPA when the value is not provided by the CPU in HPFAR_EL1. If a translation table walk causes an external abort it is taken as an exception, even if it was due to an AT instruction. (DDI0487F.a's D5.2.11 "Synchronous faults generated by address translation instructions") While we previously made KVM resilient to exceptions taken due to AT instructions, the device access causes mismatched attributes, and may occur speculatively. Prevent this, by forbidding a walk through memory described as device at stage2. Now such AT instructions will report a stage2 fault. Such a fault will cause KVM to restart the guest. If the AT instructions always walk the page tables, but guest execution uses the translation cached in the TLB, the guest can't make forward progress until the TLB entry is evicted. This isn't a problem, as since commit 5dcd0fdb ("KVM: arm64: Defer guest entry when an asynchronous exception is pending"), KVM will return to the host to process IRQs allowing the rest of the system to keep running. Cc: stable@vger.kernel.org # v4.19 Signed-off-by:
James Morse <james.morse@arm.com> Reviewed-by:
Marc Zyngier <maz@kernel.org> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Andre Przywara <andre.przywara@arm.com> Signed-off-by:
-
James Morse authored
commit 88a84ccc upstream. KVM doesn't expect any synchronous exceptions when executing, any such exception leads to a panic(). AT instructions access the guest page tables, and can cause a synchronous external abort to be taken. The arm-arm is unclear on what should happen if the guest has configured the hardware update of the access-flag, and a memory type in TCR_EL1 that does not support atomic operations. B2.2.6 "Possible implementation restrictions on using atomic instructions" from DDI0487F.a lists synchronous external abort as a possible behaviour of atomic instructions that target memory that isn't writeback cacheable, but the page table walker may behave differently. Make KVM robust to synchronous exceptions caused by AT instructions. Add a get_user() style helper for AT instructions that returns -EFAULT if an exception was generated. While KVM's version of the exception table mixes synchronous and asynchronous exceptions, only one of these can occur at each location. Re-enter the guest when the AT instructions take an exception on the assumption the guest will take the same exception. This isn't guaranteed to make forward progress, as the AT instructions may always walk the page tables, but guest execution may use the translation cached in the TLB. This isn't a problem, as since commit 5dcd0fdb ("KVM: arm64: Defer guest entry when an asynchronous exception is pending"), KVM will return to the host to process IRQs allowing the rest of the system to keep running. Cc: stable@vger.kernel.org # v4.19 Signed-off-by:
-
James Morse authored
commit 5dcd0fdb upstream. SError that occur during world-switch's entry to the guest will be accounted to the guest, as the exception is masked until we enter the guest... but we want to attribute the SError as precisely as possible. Reading DISR_EL1 before guest entry requires free registers, and using ESB+DISR_EL1 to consume and read back the ESR would leave KVM holding a host SError... We would rather leave the SError pending and let the host take it once we exit world-switch. To do this, we need to defer guest-entry if an SError is pending. Read the ISR to see if SError (or an IRQ) is pending. If so fake an exit. Place this check between __guest_enter()'s save of the host registers, and restore of the guest's. SError that occur between here and the eret into the guest must have affected the guest's registers, which we can naturally attribute to the guest. The dsb is needed to ensure any previous writes have been done before we read ISR_EL1. On systems without the v8.2 RAS extensions this doesn't give us anything as we can't contain errors, and the ESR bits to describe the severity are all implementation-defined. Replace this with a nop for these systems. Cc: stable@vger.kernel.org # v4.19 Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
James Morse authored
commit e9ee186b upstream. KVM has a one instruction window where it will allow an SError exception to be consumed by the hypervisor without treating it as a hypervisor bug. This is used to consume asynchronous external abort that were caused by the guest. As we are about to add another location that survives unexpected exceptions, generalise this code to make it behave like the host's extable. KVM's version has to be mapped to EL2 to be accessible on nVHE systems. The SError vaxorcism code is a one instruction window, so has two entries in the extable. Because the KVM code is copied for VHE and nVHE, we end up with four entries, half of which correspond with code that isn't mapped. Signed-off-by:
-
Eugeniu Rosca authored
commit dc07a728 upstream. Commit 52f23478 ("mm/slub.c: fix corrupted freechain in deactivate_slab()") suffered an update when picked up from LKML [1]. Specifically, relocating 'freelist = NULL' into 'freelist_corrupted()' created a no-op statement. Fix it by sticking to the behavior intended in the original patch [1]. In addition, make freelist_corrupted() immune to passing NULL instead of &freelist. The issue has been spotted via static analysis and code review. [1] https://lore.kernel.org/linux-mm/20200331031450.12182-1-dongli.zhang@oracle.com/ Fixes: 52f23478 ("mm/slub.c: fix corrupted freechain in deactivate_slab()") Signed-off-by:
Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by:
-
Ye Bin authored
commit 219403d7 upstream. Maybe __create_persistent_data_objects() caller will use PTR_ERR as a pointer, it will lead to some strange things. Signed-off-by:
Ye Bin <yebin10@huawei.com> Cc: stable@vger.kernel.org Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Ye Bin authored
commit d16ff19e upstream. Maybe __create_persistent_data_objects() caller will use PTR_ERR as a pointer, it will lead to some strange things. Signed-off-by:
-
Mikulas Patocka authored
commit f9e040ef upstream. The function dax_direct_access doesn't take partitions into account, it always maps pages from the beginning of the device. Therefore, persistent_memory_claim() must get the partition offset using get_start_sect() and add it to the page offsets passed to dax_direct_access(). Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Fixes: 48debafe ("dm: add writecache target") Cc: stable@vger.kernel.org # 4.18+ Signed-off-by:
-
Tejun Heo authored
commit 3b545563 upstream. All three generations of Sandisk SSDs lock up hard intermittently. Experiments showed that disabling NCQ lowered the failure rate significantly and the kernel has been disabling NCQ for some models of SD7's and 8's, which is obviously undesirable. Karthik worked with Sandisk to root cause the hard lockups to trim commands larger than 128M. This patch implements ATA_HORKAGE_MAX_TRIM_128M which limits max trim size to 128M and applies it to all three generations of Sandisk SSDs. Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Karthik Shivaram <karthikgs@fb.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Ming Lei authored
commit 7e249690 upstream. Block layer usually doesn't support or allow zero-length bvec. Since commit 1bdc76ae ("iov_iter: use bvec iterator to implement iterate_bvec()"), iterate_bvec() switches to bvec iterator. However, Al mentioned that 'Zero-length segments are not disallowed' in iov_iter. Fixes for_each_bvec() so that it can move on after seeing one zero length bvec. Fixes: 1bdc76ae ("iov_iter: use bvec iterator to implement iterate_bvec()") Reported-by:
syzbot <syzbot+61acc40a49a3e46e25ea@syzkaller.appspotmail.com> Signed-off-by:
Ming Lei <ming.lei@redhat.com> Tested-by:
-
Max Staudt authored
commit d3a84a8d upstream. The basic permission bits (protection bits in AmigaOS) have been broken in Linux' AFFS - it would only set bits, but never delete them. Also, contrary to the documentation, the Archived bit was not handled. Let's fix this for good, and set the bits such that Linux and classic AmigaOS can coexist in the most peaceful manner. Also, update the documentation to represent the current state of things. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Signed-off-by:
Max Staudt <max@enpas.org> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Sean Young authored
commit 4f0835d6 upstream. Only report uevent file contents if device still registered, else we might read freed memory. Reported-by: syzbot+ceef16277388d6f24898@syzkaller.appspotmail.com Cc: Hillf Danton <hdanton@sina.com> Cc: <stable@vger.kernel.org> # 4.16+ Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by:
-
Sean Young authored
commit a2e2d73f upstream. Device drivers do not expect to have change_protocol or wakeup re-programming to be accesed after rc_unregister_device(). This can cause the device driver to access deallocated resources. Cc: <stable@vger.kernel.org> # 4.16+ Signed-off-by:
-
Dan Crawford authored
commit 15cbff3f upstream. Following Christian Lachner's patch for Gigabyte X570-based motherboards, also patch the MSI X570-A PRO motherboard; the ALC1220 codec requires the same workaround for Clevo laptops to enforce the DAC/mixer connection path. Set up a quirk entry for that. I suspect most if all X570 motherboards will require similar patches. [ The entries reordered in the SSID order -- tiwai ] Related buglink: https://bugzilla.kernel.org/show_bug.cgi?id=205275Signed-off-by:
Dan Crawford <dnlcrwfrd@gmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200829024946.5691-1-dnlcrwfrd@gmail.comSigned-off-by:
-
Takashi Sakamoto authored
commit acd46a6b upstream. Avid Adrenaline is reported that ALSA firewire-digi00x driver is bound to. However, as long as he investigated, the design of this model is hardly similar to the one of Digi 00x family. It's better to exclude the model from modalias of ALSA firewire-digi00x driver. This commit changes device entries so that the model is excluded. $ python3 crpp < ~/git/am-config-rom/misc/avid-adrenaline.img ROM header and bus information block ----------------------------------------------------------------- 400 04203a9c bus_info_length 4, crc_length 32, crc 15004 404 31333934 bus_name "1394" 408 e064a002 irmc 1, cmc 1, isc 1, bmc 0, cyc_clk_acc 100, max_rec 10 (2048) 40c 00a07e01 company_id 00a07e | 410 00085257 device_id 0100085257 | EUI-64 00a07e0100085257 root directory ----------------------------------------------------------------- 414 0005d08c directory_length 5, crc 53388 418 0300a07e vendor 41c 8100000c --> descriptor leaf at 44c 420 0c008380 node capabilities 424 8d000002 --> eui-64 leaf at 42c 428 d1000004 --> unit directory at 438 eui-64 leaf at 42c ----------------------------------------------------------------- 42c 0002410f leaf_length 2, crc 16655 430 00a07e01 company_id 00a07e | 434 00085257 device_id 0100085257 | EUI-64 00a07e0100085257 unit directory at 438 ----------------------------------------------------------------- 438 0004d6c9 directory_length 4, crc 54985 43c 1200a02d specifier id: 1394 TA 440 13014001 version: Vender Unique and AV/C 444 17000001 model 448 81000009 --> descriptor leaf at 46c descriptor leaf at 44c ----------------------------------------------------------------- 44c 00077205 leaf_length 7, crc 29189 450 00000000 textual descriptor 454 00000000 minimal ASCII 458 41766964 "Avid" 45c 20546563 " Tec" 460 686e6f6c "hnol" 464 6f677900 "ogy" 468 00000000 descriptor leaf at 46c ----------------------------------------------------------------- 46c 000599a5 leaf_length 5, crc 39333 470 00000000 textual descriptor 474 00000000 minimal ASCII 478 41647265 "Adre" 47c 6e616c69 "nali" 480 6e650000 "ne" Reported-by:
Simon Wood <simon@mungewell.org> Fixes: 9edf723f ("ALSA: firewire-digi00x: add skeleton for Digi 002/003 family") Cc: <stable@vger.kernel.org> # 4.4+ Signed-off-by:
-
Kai Vehmanen authored
commit 858e0ad9 upstream. When system is suspended with active audio playback to HDMI/DP, two alternative sequences can happen at resume: a) monitor is detected first and ALSA prepare follows normal stream setup sequence, or b) ALSA prepare is called first, but monitor is not yet detected, so PCM is restarted without a pin, In case of (b), on i915 systems, haswell_verify_D0() is not called at resume and the pin power state may be incorrect. Result is lack of audio after resume with no error reported back to user-space. Fix the problem by always verifying converter and pin state in the i915_pin_cvt_fixup(). BugLink: https://github.com/thesofproject/linux/issues/2388Signed-off-by:
Kai Vehmanen <kai.vehmanen@linux.intel.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200826170306.701566-1-kai.vehmanen@linux.intel.comSigned-off-by:
-
Takashi Iwai authored
commit 949a1ebe upstream. The PCM OSS mulaw plugin has a check of the format of the counter part whether it's a linear format. The check is with snd_BUG_ON() that emits WARN_ON() when the debug config is set, and it confuses syzkaller as if it were a serious issue. Let's drop snd_BUG_ON() for avoiding that. While we're at it, correct the error code to a more suitable, EINVAL. Reported-by: syzbot+23b22dc2e0b81cbfcc95@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200901131802.18157-1-tiwai@suse.deSigned-off-by:
-
Tong Zhang authored
commit ee0761d1 upstream. snd_ca0106_spi_write() returns 1 on error, snd_ca0106_pcm_power_dac() is returning the error code directly, and the caller is expecting an negative error code Signed-off-by:
Tong Zhang <ztong0001@gmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200824224541.1260307-1-ztong0001@gmail.comSigned-off-by:
-
Rogan Dawes authored
[ Upstream commit 7d605309 ] Signed-off-by:
Rogan Dawes <rogan@dawes.za.net> Signed-off-by:
-
Daniele Palmas authored
[ Upstream commit e0ae2c57 ] This patch adds support for Telit FN980 0x1050 composition 0x1050: tty, adb, rmnet, tty, tty, tty, tty Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
Josef Bacik authored
[ Upstream commit a48b73ec ] With the conversion of the tree locks to rwsem I got the following lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.8.0-rc7-00165-g04ec4da5f45f-dirty #922 Not tainted ------------------------------------------------------ compsize/11122 is trying to acquire lock: ffff889fabca8768 (&mm->mmap_lock#2){++++}-{3:3}, at: __might_fault+0x3e/0x90 but task is already holding lock: ffff889fe720fe40 (btrfs-fs-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x39/0x180 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (btrfs-fs-00){++++}-{3:3}: down_write_nested+0x3b/0x70 __btrfs_tree_lock+0x24/0x120 btrfs_search_slot+0x756/0x990 btrfs_lookup_inode+0x3a/0xb4 __btrfs_update_delayed_inode+0x93/0x270 btrfs_async_run_delayed_root+0x168/0x230 btrfs_work_helper+0xd4/0x570 process_one_work+0x2ad/0x5f0 worker_thread+0x3a/0x3d0 kthread+0x133/0x150 ret_from_fork+0x1f/0x30 -> #1 (&delayed_node->mutex){+.+.}-{3:3}: __mutex_lock+0x9f/0x930 btrfs_delayed_update_inode+0x50/0x440 btrfs_update_inode+0x8a/0xf0 btrfs_dirty_inode+0x5b/0xd0 touch_atime+0xa1/0xd0 btrfs_file_mmap+0x3f/0x60 mmap_region+0x3a4/0x640 do_mmap+0x376/0x580 vm_mmap_pgoff+0xd5/0x120 ksys_mmap_pgoff+0x193/0x230 do_syscall_64+0x50/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xa9 -> #0 (&mm->mmap_lock#2){++++}-{3:3}: __lock_acquire+0x1272/0x2310 lock_acquire+0x9e/0x360 __might_fault+0x68/0x90 _copy_to_user+0x1e/0x80 copy_to_sk.isra.32+0x121/0x300 search_ioctl+0x106/0x200 btrfs_ioctl_tree_search_v2+0x7b/0xf0 btrfs_ioctl+0x106f/0x30a0 ksys_ioctl+0x83/0xc0 __x64_sys_ioctl+0x16/0x20 do_syscall_64+0x50/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xa9 other info that might help us debug this: Chain exists of: &mm->mmap_lock#2 --> &delayed_node->mutex --> btrfs-fs-00 Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(btrfs-fs-00); lock(&delayed_node->mutex); lock(btrfs-fs-00); lock(&mm->mmap_lock#2); *** DEADLOCK *** 1 lock held by compsize/11122: #0: ffff889fe720fe40 (btrfs-fs-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x39/0x180 stack backtrace: CPU: 17 PID: 11122 Comm: compsize Kdump: loaded Not tainted 5.8.0-rc7-00165-g04ec4da5f45f-dirty #922 Hardware name: Quanta Tioga Pass Single Side 01-0030993006/Tioga Pass Single Side, BIOS F08_3A18 12/20/2018 Call Trace: dump_stack+0x78/0xa0 check_noncircular+0x165/0x180 __lock_acquire+0x1272/0x2310 lock_acquire+0x9e/0x360 ? __might_fault+0x3e/0x90 ? find_held_lock+0x72/0x90 __might_fault+0x68/0x90 ? __might_fault+0x3e/0x90 _copy_to_user+0x1e/0x80 copy_to_sk.isra.32+0x121/0x300 ? btrfs_search_forward+0x2a6/0x360 search_ioctl+0x106/0x200 btrfs_ioctl_tree_search_v2+0x7b/0xf0 btrfs_ioctl+0x106f/0x30a0 ? __do_sys_newfstat+0x5a/0x70 ? ksys_ioctl+0x83/0xc0 ksys_ioctl+0x83/0xc0 __x64_sys_ioctl+0x16/0x20 do_syscall_64+0x50/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xa9 The problem is we're doing a copy_to_user() while holding tree locks, which can deadlock if we have to do a page fault for the copy_to_user(). This exists even without my locking changes, so it needs to be fixed. Rework the search ioctl to do the pre-fault and then copy_to_user_nofault for the copying. CC: stable@vger.kernel.org # 4.4+ Reviewed-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
Josef Bacik <josef@toxicpanda.com> Reviewed-by:
-
