Add support for RS-485 multipoint addressing using 9th bit [*]. The
addressing mode is configured through ->rs485_config().

ADDRB in termios indicates 9th bit addressing mode is enabled. In this
mode, 9th bit is used to indicate an address (byte) within the
communication line. ADDRB can only be enabled/disabled through
->rs485_config() that is also responsible for setting the destination and
receiver (filter) addresses.

Add traps to detect unwanted changes to struct serial_rs485 layout using
static_assert().

[*] Technically, RS485 is just an electronic spec and does not itself
specify the 9th bit addressing mode but 9th bit seems at least
"semi-standard" way to do addressing with RS485.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-6-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-5-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use 32-bit reads in order to not lose higher bits of DW UART regs. This
change does not fix any known issue as the high bits are not used for
anything related to 8250 driver (dw8250_readl_ext and dw8250_writel_ext
used within the dwlib are already doing
readl/writel/ioread32be/iowrite32be anyway).

This change is necessary to enables 9th bit address mode. DW UART
reports address frames with BIT(8) of LSR.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-4-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow drivers to alter LSR save mask.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-3-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

DW flags address received as BIT(8) in LSR. In order to not lose that
on read, enlarge lsr_saved_flags to u16.

Adjust lsr/status variables and related call chains to use u16.
Technically, some of these type conversion would not be needed but it
doesn't hurt to be consistent.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-2-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Per file BOTH_EMPTY defines are littering our source code here and
there. Define once in serial.h and create helper for the check
too.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-7-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Both UART_XMIT_SIZE and SERIAL_XMIT_SIZE are defined. Make them all
UART_XMIT_SIZE.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-6-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use C99 array initializer insteads of comments and make unmapped checks
more obvious.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-5-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of listing the bits for UART_LSR_BRK_ERROR_BITS and
UART_MSR_ANY_DELTA in comment, use them to define instead.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-4-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using UART_* to name defines is a bit problematic. When trying to do
unrelated cleanup which also involved tweaking header inclusion logic,
caused UART_CSR from serial_reg.h to leak into msm's namespace which is
also among msm defines. Thus, rename all UART_* ones to MSM_UART_* to
eliminate possibility of collisions.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-3-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Create static inline instead of define as it provides type safety and
is safer wrt. macros expansion.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-2-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

st-asc driver doesn't use helpers from pm_runtime.h thus remove its
include.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-5-claudiu.beznea@microchip.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need for clk_prepare_enable() at the beginning of
atmel_console_setup() and clk_disable_unprepare() at the end of
atmel_console_setup() as the clock is already enabled when calling
atmel_console_setup() and its disablement is done at the end
of probe.
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-4-claudiu.beznea@microchip.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use devm_clk_get() for serial clock instead of clk_get()/clk_put().
With this move the clk_get in driver's probe function.
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-3-claudiu.beznea@microchip.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Stop using legacy PM ops and switch using dev_pm_ops. Along with
it #ifdef CONFIG_PM are removed and __maybe_unused and pm_ptr() used
instead. Coding style recommends (at chapter Conditional Compilation)
to avoid using preprocessor conditional and use __maybe_unused
instead.
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-2-claudiu.beznea@microchip.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a Rockchip RK3588 compatible.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220623161350.242079-1-sebastian.reichel@collabora.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Delete the redundant word 'the'.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Link: https://lore.kernel.org/r/20220620104653.5451-1-wangxiang@cdjrlc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add myself as maintainer for DW 8250 UART and up it to Supported.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/be58b398-71ff-7c12-1bf1-a09181d9c80@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220613131007.10027-1-wsa+renesas@sang-engineering.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In soc_info(), of_find_node_by_type() will return a node pointer
with refcount incremented. We should use of_node_put() when it is
not used anymore.
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220618060850.4058525-1-windhl@126.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In tegra_uart_init(), of_find_matching_node() will return a node
pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220615111747.3963930-1-windhl@126.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit 31f6bd7f ("serial: Store character timing information
to uart_port"), per frame timing information is available on uart_port.
Uart port's timeout can be derived from frame_time by multiplying with
fifosize.

Most callers of uart_poll_timeout are not made under port's lock. To be
on the safe side, make sure frame_time is only accessed once. As
fifo_size is effectively a constant, it shouldn't cause any issues.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220613113905.22962-1-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The closing `` is missing. Add it.

Fixes: 6bb6fa69 ("tty: Implement lookahead to process XON/XOFF timely")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/9bc6d45d-48c8-519-1646-78ba22505b1f@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use UART_LCR_DLAB instead of literal.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220613075736.12283-2-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use UART_LCR_WLEN8 instead of literal 0x03 in size_fifo().
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220613075736.12283-1-ilpo.jarvinen@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An SPDX-License-Identifier is already in place. There is no need to
duplicate part of the corresponding license.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dbc54eff6f4e077d9126054f395d5bc5b3405917.1654936915.git.christophe.jaillet@wanadoo.frSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code expects "translations" to have 256 (E_TABSZ) values. Use the
macro instead of the constant to be explicit about this.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-8-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

con_do_clear_unimap() sets dflt to NULL and then calls
con_release_unimap() which does the very same as the first thing. So
remove the former as it is apparently superfluous.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-7-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use FIELD_GET() and GENMASK() helpers instead of direct shifts and ANDs.
This makes the code even more obvious. I didn't know about the helpers
at the time of writing the macros.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-6-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As a follow-up to the commit 4173f018 (tty/vt: consolemap: rename
and document struct uni_pagedir), rename also the members of struct
vc_data. I.e. pagedir -> pagedict. And while touching all the places,
remove also the unnecessary vc_ prefix.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-5-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.

Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...

This is a lot of shuffling, but the result pays off, IMO.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-4-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function still uses too vague parameter name after commit
50c92a1b (tty/vt: consolemap: saner variable names in
set_inverse_trans_unicode()).

So use "dict" instead of "p" for that parameter too.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-3-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

conp is unused in set_inverse_trans_unicode(), remove it.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-2-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code still uses constants (macros) as bounds in loops after commit
17945d31 (tty/vt: consolemap: use ARRAY_SIZE()). The contants are at
least macros used also in the definition of the arrays. But use
ARRAY_SIZE() on two more places to ensure the loops never run out of
bounds even if the array definition change.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-1-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull x86 fixes from Thomas Gleixner:

 - Make RESERVE_BRK() work again with older binutils. The recent
   'simplification' broke that.

 - Make early #VE handling increment RIP when successful.

 - Make the #VE code consistent vs. the RIP adjustments and add
   comments.

 - Handle load_unaligned_zeropad() across page boundaries correctly in
   #VE when the second page is shared.

* tag 'x86-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tdx: Handle load_unaligned_zeropad() page-cross to a shared page
  x86/tdx: Clarify RIP adjustments in #VE handler
  x86/tdx: Fix early #VE handling
  x86/mm: Fix RESERVE_BRK() for older binutils

Pull build tooling updates from Thomas Gleixner:

 - Remove obsolete CONFIG_X86_SMAP reference from objtool

 - Fix overlapping text section failures in faddr2line for real

 - Remove OBJECT_FILES_NON_STANDARD usage from x86 ftrace and replace it
   with finegrained annotations so objtool can validate that code
   correctly.

* tag 'objtool-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ftrace: Remove OBJECT_FILES_NON_STANDARD usage
  faddr2line: Fix overlapping text section failures, the sequel
  objtool: Fix obsolete reference to CONFIG_X86_SMAP

Pull scheduler fix from Thomas Gleixner:
 "A single scheduler fix plugging a race between sched_setscheduler()
  and balance_push().

  sched_setscheduler() spliced the balance callbacks accross a lock
  break which makes it possible for an interleaving schedule() to
  observe an empty list"

* tag 'sched-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix balance_push() vs __sched_setscheduler()

Pull lockdep fix from Thomas Gleixner:
 "A RT fix for lockdep.

  lockdep invokes prandom_u32() to create cookies. This worked until
  prandom_u32() was switched to the real random generator, which takes a
  spinlock for extraction, which does not work on RT when invoked from
  atomic contexts.

  lockdep has no requirement for real random numbers and it turns out
  sched_clock() is good enough to create the cookie. That works
  everywhere and is faster"

* tag 'locking-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/lockdep: Use sched_clock() for random numbers