Skip to content

L
linux
Switch branch/tag
  1. 11 Mar, 2013 2 commits
  3. 08 Mar, 2013 1 commit
  5. 07 Mar, 2013 9 commits
  7. 05 Mar, 2013 8 commits
    • Aaro Koskinen's avatar
      usb: musb: omap2430: fix sparse warning · 4b58ed11
      Aaro Koskinen authored 
      Fix the following sparse warning:

drivers/usb/musb/omap2430.c:54:33: warning: symbol '_glue' was not \
	declared. Should it be static?
Signed-off-by: default avatarAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      4b58ed11
    • Aaro Koskinen's avatar
      usb: musb: omap2430: fix omap_musb_mailbox glue check again · f8c4b0e7
      Aaro Koskinen authored 
      Commit 80ab72e1 (usb: musb: omap2430: fix the readiness check
in omap_musb_mailbox) made the check incorrect, as we will lose the
glue/link status during the normal built-in probe order (twl4030_usb is
probed after musb omap2430, but before musb core is ready).

As a result, if you boot with USB cable on and load g_ether, the
connection does not work as the code thinks the cable is off and the
phy gets powered down immediately. This is a major regression in 3.9-rc1.

So the proper check should be: exit if _glue is NULL, but if it's
initialized we memorize the status, and then check if the musb core
is ready.
Signed-off-by: default avatarAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      f8c4b0e7
    • Felipe Balbi's avatar
      usb: musb: fix compile warning · e574d570
      Felipe Balbi authored 
      When running 100 randconfig iterations, I found
the following warning:

drivers/usb/musb/musb_core.c: In function ‘musb_init_controller’:
drivers/usb/musb/musb_core.c:1981:1: warning: label ‘fail5’ defined \
	but not used [-Wunused-label]

this patch fixes it by removing the unnecessary
ifdef CONFIG_SYSFS.
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      e574d570
    • Felipe Balbi's avatar
      usb: musb: remove all 'select' from Kconfig · 341a71c7
      Felipe Balbi authored 
      those are quite unnecessary, the only thing
we need to be careful about is USB_OTG_UTILS
which get properly selected by PHY drivers.

For now, MUSB will select only USB_OTG_UTILS
until we add stubs for the cases when PHY
layer isn't enabled.
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      341a71c7
    • Nishanth Menon's avatar
      usb: gadget: composite: fix kernel-doc warnings · 43febb27
      Nishanth Menon authored 
      A few trivial fixes for composite driver:

Warning(include/linux/usb/composite.h:165): No description found for parameter
	'fs_descriptors'
Warning(include/linux/usb/composite.h:165): Excess struct/union/enum/typedef
	member 'descriptors' description in 'usb_function'
Warning(include/linux/usb/composite.h:321): No description found for parameter
	'gadget_driver'
Warning(drivers/usb/gadget/composite.c:1777): Excess function parameter 'bind'
	description in 'usb_composite_probe'

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: default avatarNishanth Menon <nm@ti.com>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      43febb27
    • Alan Stern's avatar
      USB: EHCI: don't check DMA values in QH overlays · feca7746
      Alan Stern authored 
      This patch (as1661) fixes a rather obscure bug in ehci-hcd.  In a
couple of places, the driver compares the DMA address stored in a QH's
overlay region with the address of a particular qTD, in order to see
whether that qTD is the one currently being processed by the hardware.
(If it is then the status in the QH's overlay region is more
up-to-date than the status in the qTD, and if it isn't then the
overlay's value needs to be adjusted when the QH is added back to the
active schedule.)

However, DMA address in the overlay region isn't always valid.  It
sometimes will contain a stale value, which may happen by coincidence
to be equal to a qTD's DMA address.  Instead of checking the DMA
address, we should check whether the overlay region is active and
valid.  The patch tests the ACTIVE bit in the overlay, and clears this
bit when the overlay becomes invalid (which happens when the
currently-executing URB is unlinked).

This is the second part of a fix for the regression reported at:

	https://bugs.launchpad.net/bugs/1088733Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Reported-by: default avatarJoseph Salisbury <joseph.salisbury@canonical.com>
Reported-and-tested-by: default avatarStephen Thirlwall <sdt@dr.com>
CC: <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      feca7746
    • Alan Stern's avatar
      USB: EHCI: work around silicon bug in Intel's EHCI controllers · 6402c796
      Alan Stern authored 
      This patch (as1660) works around a hardware problem present in some
(if not all) Intel EHCI controllers.  After a QH has been unlinked
from the async schedule and the corresponding IAA interrupt has
occurred, the controller is not supposed access the QH and its qTDs.
There certainly shouldn't be any more DMA writes to those structures.
Nevertheless, Intel's controllers have been observed to perform a
final writeback to the QH's overlay region and to the most recent qTD.
For more information and a test program to determine whether this
problem is present in a particular controller, see

	http://marc.info/?l=linux-usb&m=135492071812265&w=2
	http://marc.info/?l=linux-usb&m=136182570800963&w=2

This patch works around the problem by always waiting for two IAA
cycles when unlinking an async QH.  The extra IAA delay gives the
controller time to perform its final writeback.

Surprisingly enough, the effects of this silicon bug have gone
undetected until quite recently.  More through luck than anything
else, it hasn't caused any apparent problems.  However, it does
interact badly with the path that follows this one, so it needs to be
addressed.

This is the first part of a fix for the regression reported at:

	https://bugs.launchpad.net/bugs/1088733Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Tested-by: default avatarStephen Thirlwall <sdt@dr.com>
CC: <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      6402c796
    • Greg Kroah-Hartman's avatar
      Merge tag 'fixes-for-v3.9-rc2' of... · ea5301aa
      Greg Kroah-Hartman authored 
      Merge tag 'fixes-for-v3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

"usb: fixes for v3.9-rc2

A few drivers got their gadget->dev registration problems
exposed by the removal of ->start()/->stop() functions from
udc-core.c. All of such instances are now fixed.

We're also fixing chipidea's mistake of registering private
debugging sysfs files under the gadget's device. This is
in preparation to complete removal of gadget->dev handling
from all UDC drivers which will happen for v3.10 merge window.

MUSB's Kconfig got a fix to avoid a non-buildable selection
of its Kconfig choices.

Some extra devm_ioremap_resource() are added here because they
missed the merge window.

Finally, we have a temporary fix linking function drivers
before gadget drivers so they work fine when they're statically
linked to the kernel. We've done it so since the real fix wouldn't
fit the -rc cycle."
      ea5301aa
  9. 04 Mar, 2013 18 commits
  11. 03 Mar, 2013 2 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7