- 03 Apr, 2023 2 commits
-
-
Ankit Nautiyal authored
Go with DSC only if the given output_format is supported. v2: Use drm helper to get DSC format support for sink. v3: remove drm_dp_dsc_compute_bpp. Cc: Uma Shankar <uma.shankar@intel.com> Signed-off-by:
Ankit Nautiyal <ankit.k.nautiyal@intel.com> Reviewed-by:
Uma Shankar <uma.shankar@intel.com> Signed-off-by:
-
Ankit Nautiyal authored
Add helper to check if the DP sink supports DSC with the given o/p format. v2: Add documentation for the helper. (Uma Shankar) v3: /** instead of /* (Uma Shankar) Signed-off-by:
-
- 31 Mar, 2023 9 commits
-
-
Ville Syrjälä authored
Define CUR_CHICKEN so we don't have to remember the offset. Looks like it's getting introduced in mtl. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230329190445.13456-3-ville.syrjala@linux.intel.comReviewed-by:
Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
Add tgl+ comments to the PLANE_CHICKEN registers which I apparently forgot to add when defining the registers. Signed-off-by:
-
Ville Syrjälä authored
Cursor is not a universal plane and thus doesn't have the PLANE_CHICKEN register. Skip it. Fixes: c5de2484 ("drm/i915/dpt: Add a modparam to disable DPT via the chicken bit") Signed-off-by:
-
Jouni Högander authored
Implement Display WA #1136 for Pre-ICL. Bspec: 21664 v2: Handle disable psr in pre/post plane hooks Signed-off-by:
Jouni Högander <jouni.hogander@intel.com> Reviewed-by:
-
Jouni Högander authored
Ensure vblank >= psr2 vblank where Psr2 vblank = PSR2_CTL Block Count Number maximum line count. Bspec: 71580, 49274 v2: Use calculated block count number maximum line count Signed-off-by:
-
Jouni Högander authored
Add helpers to make it more clear how PSR2_CTL[Block Count Number] is configured. Signed-off-by:
-
Jouni Högander authored
PSR WM optimization should be disabled based on any wm level being disabled. Also same WA should be applied for ICL as well. Bspec: 71580 v5: - Set in pre plane hook and clear in post plane hook v4: - Handle mode change in psr enable/disable - Handle wm_level_disable changes separately in pre plane hook v3: - Split patch v2: - set/clear chicken bit in post_plane_update - apply for ICL as well Signed-off-by:
-
Jouni Högander authored
Wa_16013835468 is a separate from Wa_14015648006 and needs to be applied for display version 12. Fix this by removing all the references to Wa_14015648006 and apply Wa_16013835468 according to Bspec. Also move workaround into separate function as a preparation for Wa_14015648006 implementation. Bspec: 55378 v3: - apply for display version 12 only v2: - keep applying the wa in intel_psr_enable_source Signed-off-by:
-
Jouni Högander authored
pre/post hooks are doing things differently. Unify them. Signed-off-by:
-
- 30 Mar, 2023 7 commits
-
-
Daniele Ceraolo Spurio authored
The PTEs expect the offset from the base of the fake LMEM region (i.e. the base of stolen) and not from the base of the DSM. Quoting the specs: "Driver will set the Device Memory bit = 1 in the PTE when pointing to a page in DSM and program the PTE with offset from LMEM_BAR. Device Memory Offset from LMEM_BAR is same as offset from BGSM." DSM starts 8MBs from BGSM, so we set dsm_base = 8MB. Signed-off-by:
Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Aravind Iddamsetty <aravind.iddamsetty@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Nirmoy Das <nirmoy.das@intel.com> Cc: Fei Yang <fei.yang@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Reviewed-by:
Andi Shyti <andi.shyti@linux.intel.com> Reviewed-by:
Nirmoy Das <nirmoy.das@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230328012430.2524330-1-daniele.ceraolospurio@intel.com
-
Jani Nikula authored
Clean up i915_reg.h by splitting out DSB regs to display/intel_dsb_regs.h. Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
-
Jani Nikula authored
Clean up i915_reg.h by splitting out FDI regs to display/intel_fdi_regs.h. Signed-off-by:
-
Jani Nikula authored
Clean up i915_reg.h by splitting out DP AUX regs to display/intel_dp_aux_regs.h. Signed-off-by:
-
Jani Nikula authored
Clean up i915_reg.h by splitting out TV regs to display/intel_tv_regs.h. Signed-off-by:
-
Jani Nikula authored
Clean up i915_reg.h by splitting out PPS regs to display/intel_pps_regs.h. Signed-off-by:
-
Ville Syrjälä authored
Only the PWM output mode of the utility pin is incompatible with DC6/LCPLL disable. Check for that specifically. References: https://gitlab.freedesktop.org/drm/intel/-/issues/6609Signed-off-by:
-
- 29 Mar, 2023 1 commit
-
-
Stanislav Lisovskiy authored
For obvious reasons, we use compressed bpp instead of pipe bpp for DSC DP SST case. Lets be consistent and use compressed bpp instead of pipe bpp, also in DP MST DSC case. Signed-off-by:
Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Reviewed-by:
Vinod Govindapillai <vinod.govindapillai@intel.com> Fixes: d51f25eb ("drm/i915: Add DSC support to MST path") Link: https://patchwork.freedesktop.org/patch/msgid/20230327064217.24033-1-stanislav.lisovskiy@intel.com
-
- 28 Mar, 2023 4 commits
-
-
Jani Nikula authored
Essentially this is a revert of commit d9d54a53 ("drm/i915: Put future HW and their uAPIs under STAGING & BROKEN"). We currently have no users for this config option. The last one was removed in commit 8c26491f ("drm/i915: Kill the fake lmem support"). Drop it altogether; it's easy enough to resurrect if need arises. Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230327105330.312131-2-jani.nikula@intel.com
-
Rodrigo Vivi authored
Catch up with 6.3-rc cycle... Signed-off-by: -
Ville Syrjälä authored
Similar to FBC let's expose an debugfs file to control IPS false color. Enabling this provides an immediate visual feedback on whether IPS is working or not. Signed-off-by:
-
Ville Syrjälä authored
IPS is a per-pipe feature, so let's move the debugfs stuff under the crtc directory, and only register it when IPS is actually available. Signed-off-by:
-
- 27 Mar, 2023 3 commits
-
-
Daniel Vetter authored
Merge tag 'drm-rcar-next-20230325' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux into drm-next Miscellaneous fixes and improvements for rcar-du Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> From: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230325204922.GD19335@pendragon.ideasonboard.com
-
Vinod Govindapillai authored
Wrong register address is used to read the SAG block time. Fix the register address according to the bspec. Bspec: 64608 Signed-off-by:
-
Vinod Govindapillai authored
Wrong offsets are calculated to read QGV point registers. Fix it to read from the correct registers. Bspec: 64602 Reviewed-by:
-
- 25 Mar, 2023 8 commits
-
-
Dan Carpenter authored
The drmm_encoder_alloc() function returns error pointers. It never returns NULL. Fix the check accordingly. Fixes: 7a1adbd2 ("drm: rcar-du: Use drmm_encoder_alloc() to manage encoder") Signed-off-by:
Dan Carpenter <error27@gmail.com> Reviewed-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
The DORCR register controls the routing of clocks and data between DU channels within a group. For groups that contain a single channel, there's no routing option to control, and some fields of the register are then reserved. On Gen2 those reserved fields are documented as required to be set to 0, while on Gen3 and newer the PG1T, DK1S and PG1D reserved fields must be set to 1. The DU driver initializes the DORCR register in rcar_du_group_setup(), where it ignores the PG1T, DK1S and PG1D, and then configures those fields to the correct value in rcar_du_group_set_routing(). This hasn't been shown to cause any issue, but prevents certifying that the driver complies with the documentation in safety-critical use cases. As there is no reasonable change that the documentation will be updated to clarify that those reserved fields can be written to 0 temporarily before starting the hardware, make sure that the registers are always set to valid values. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
-
Laurent Pinchart authored
The DORCR fields were documented in the R-Car H1 datasheet with 1-based named, and then got renamed to 0-based in Gen2. The 0-based names are used for Gen3 and Gen4, making H1 an outlier. Rename the field macros to make them 0-based, in order to increase readability of the code when comparing it with the documentation. Signed-off-by:
-
Laurent Pinchart authored
When the input to a DU channel comes from a VSP, the DU doesn't perform any blending operation. Select XRGB8888 instead of ARGB8888 to ensure that the corresponding registers don't get written with invalid values. Signed-off-by:
-
Laurent Pinchart authored
The ESCR and OTAR registers are not present in all DU channels on Gen3 SoCs. ESCR only exists in channels that can be routed to an LVDS or DPAD, and OTAR in channels that can be routed to a DPAD. Skip writing those registers for other channels. This replaces the DU gen check, as Gen4 doesn't have LVDS or DPAD outputs. Signed-off-by:
-
Laurent Pinchart authored
On R-Car D3 and E3, the LVDS encoder provides the dot (pixel) clock to the DU, regardless of whether the LVDS output is used or not. When using the DPAD (RGB) output, the DU driver thus enables and disables the LVDS PLL manually, while when using the LVDS output, it lets the LVDS bridge driver handle the PLL configuration internally as part of the atomic enable and disable operations. This causes an issue when using the LVDS output. As bridges are disabled before CRTCs, the current implementation violates the enable/disable sequences documented in the hardware datasheet, which requires the dot clock to be enabled before the CRTC is started and disabled after it gets stopped. Fix the problem by enabling/disabling the LVDS PLL manually from the DU regardless of which output is used, and skipping the PLL handling in the LVDS bridge atomic enable and disable operations. This is however not enough. Disabling the LVDS encoder while leaving the PLL on still results in a vertical blanking wait timeout when disabling the DU. Investigation showed that the culprit is the LVEN bit. For an unclear reason, clearing the bit when disabling the LVDS encoder blocks vertical blanking interrupts. We thus have to delay disabling the whole LVDS encoder, not just disabling the PLL, until the DU is disabled. We could split the LVDS disable sequence by clearing the LVRES bit in the LVDS bridge atomic disable handler, and delaying the rest of the operations, in order to disable the LVDS output at bridge atomic disable time, before stopping the CRTC. This would make the code more complex, without a clear benefit, so keep the implementation simple(r). Signed-off-by:
Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
-
Laurent Pinchart authored
To prepare for a rework of the LVDS disable code, which will need to be called from rcar_lvds_pclk_disable(), move the LVDS enable code, currently stored in the __rcar_lvds_atomic_enable() function, to a separate code section separate from bridge operations. It will be then extended with the LVDS disable code. As part of this rework the __rcar_lvds_atomic_enable() function is renamed to rcar_lvds_enable() to more clearly indicate its purpose. No functional change intended. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
-
Laurent Pinchart authored
When disabling the companion bridge in rcar_lvds_atomic_disable(), there's no need to go through the bridge's operations to call .atomic_disable(). Call rcar_lvds_atomic_disable() on the companion directly. Signed-off-by:
-
- 24 Mar, 2023 6 commits
-
-
Ville Syrjälä authored
Currently we have no sane way to forcibly disable SAGV, which makes debugging things a PITA. Manually poking at the pcode mailbox with it's various SAGV/QGV/PSF formats is no fun, and likely to be clobbered by the driver anyway. Let's add a modparam for this. Signed-off-by:
-
Ville Syrjälä authored
All other skl+ universal plane register bit definitions are next to the pipe A register definition. Move the PLANE_BUF_CFG bit definitions there as well. Signed-off-by:
Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
-
Ville Syrjälä authored
Add i915.enable_dpt modparam to allow disabling the DPT usage in hardware via the chicken bit. Useful when debugging potential DPT issues. Quickly smoke tested on ADL. Signed-off-by:
-
git://anongit.freedesktop.org/drm/drm-intelDaniel Vetter authored
Core Changes: - drm: Add SDP Error Detection Configuration Register (Arun) Driver Changes: - Meteor Lake enabling and fixes (RK, Jose, Madhumitha) - Lock the fbdev obj before vma pin (Tejas) - DSC fixes (Stanislav) - Fixes and clean-up on opregion code (Imre) - More wm/vblank stuff (Ville) - More general display code organization (Jani) - DP Fixes (Stanislav, Ville) - Introduce flags to ignore long HPD and link training issues \ for handling spurious issues on CI (Vinod) - Plane cleanups and extra registers (Ville) - Update audio keepalive clock values (Clint) - Rename find_section to bdb_find_section (Maarten) - DP SDP CRC16 for 128b132b link layer (Arun) - Fix various issues with noarm register writes (Ville) - Fix a few TypeC / MST issues (Imre) - Create GSC submission targeting HDCP and PXP usages on MTL+ (Suraj) - Enable HDCP2.x via GSC CS (Suraj) Signed-off-by:
-
git://anongit.freedesktop.org/drm/drm-miscDaniel Vetter authored
drm-misc-next for v6.4-rc1: Core Changes: - Add unit test for xrgb8888 to mono. - Assorted small fixes to format helper selftests. - Assorted documentation updates. - Drop drm_dev_set_unique. - Always use shadow buffer in generic fbdev emulation helpers, and improve error handling. Driver Changes: - Assorted small fixes to malidp, hdlcd, gma500, lima, bridge, rockchip. - Move fbdev in gma500 to use drm_client. - Convert bridge platform callbacks to void return. - Drop leftover from vgem to shmem helper conversion. Signed-off-by:
-
Ville Syrjälä authored
Define the PLANE_CHICKEN register offsets. Signed-off-by:
-
