The maximum number of SSIDs in a for active probe requests is currently
reported as 16 (WLAN_SCAN_PARAMS_MAX_SSID) when registering the driver.
The scan_req_params structure only has the capacity to hold 10 SSIDs.
This leads to a buffer overflow which can be triggered from
wpa_supplicant in userspace. When copying the SSIDs into the
scan_req_params structure in the ath11k_mac_op_hw_scan route, it can
overwrite the extraie pointer.

Firmware supports 16 ssid * 4 bssid, for each ssid 4 bssid combo probe
request will be sent, so totally 64 probe requests supported. So
set both max ssid and bssid to 16 and 4 respectively. Remove the
redundant macros of ssid and bssid.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01300-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220329150221.21907-1-quic_kathirve@quicinc.com

Remove core PCI and ath11k PCI references(struct ath11k_pci)
from PCI common code. Since, PCI common code will be used
by hybrid bus devices, this code should be independent
from ATH11K PCI references and Linux core PCI references
like struct pci_dev.

Since this change introduces function callbacks for bus wakeup
and bus release operations, wakeup_mhi HW param is no longer
needed and hence it is removed completely. Alternatively, bus
wakeup/release ops for QCA9074 are initialized to NULL as
QCA9704 does not need bus wakeup/release for register accesses.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-6-quic_mpubbise@quicinc.com

Refactor MSI logic in order to support hybrid bus devices
like WCN6750.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-5-quic_mpubbise@quicinc.com

Instead of selecting MSI config based on magic numbers, make
the assignment based on HW revision. The logic is similar to
the selection of HW params. This improves readability of the
code and also simplifies new additions.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-4-quic_mpubbise@quicinc.com

Unlike other ATH11K PCIe devices which are enumerated by APSS
processor (Application Processor SubSystem), WCN6750 gets
enumerated by the WPSS Q6 processor (Wireless Processor SubSystem);
In simple terms, though WCN6750 is PCIe device, it is not attached
to the APSS processor, APSS will not know of such a device being
present in the system and therefore WCN6750 will be registered as
a platform device to the kernel core like other supported AHB
devices.

WCN6750 needs both AHB and PCI APIs for it's operation, it uses
AHB APIs for device probe/boot and PCI APIs for device setup and
register accesses. Because of this nature, it is referred as a
hybrid bus device.

Refactor PCI code to support hybrid bus devices like WCN6750.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-3-quic_mpubbise@quicinc.com

In order to add the support for WCN6750 in ATH11K , it is
required to move certain PCI definitions to the header file.
As a result, add ATH11K_PCI_* prefix to these definitions.

Also, change the scope of certain PCI APIs that are required
to enable WCN6750 from static to global.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-2-quic_mpubbise@quicinc.com

Use macros to force strict ordering of the elements.
Signed-off-by: Benjamin Stürz <benni@stuerz.xyz>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328212912.283393-1-benni@stuerz.xyz

Replace a "mode" variable indicating "is 5ghz" with an "is2ghz" variable
to make it consistent with other functions in the file.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220326054754.27812-1-wlooi@ucalgary.ca

commit cfee8793 ("ath10k: enable napi on RX path for
sdio") introduced napi for SDIO and updated the htt interface for high
latency devices.

These changes breaks USB, so USB code must be updated to use napi as
well in order to have a working RX path.

Tested-on: QCA9377 hw1.0 USB 1.0.0.299
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220327171340.7893-2-erik.stromdahl@gmail.com

commit 93bbdec6683e1c8ba2cc4e6 ("ath10k: htt: support MSDU ids with
SDIO") introduced MSDU ID allocation in the htt TX path for high latency
devices. This feature needs to be enabled for USB as well in order to
have a functional TX path.

Tested-on: QCA9377 hw1.0 USB 1.0.0.299
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220327171340.7893-1-erik.stromdahl@gmail.com

Currently ath11k will wait 11d scan complete while add interface in
ath11k_mac_op_add_interface(), when system resume without enable
wowlan, ath11k_mac_op_add_interface() is called for each resume, thus
it increase the resume time of system. And ath11k_mac_op_hw_scan()
after ath11k_mac_op_add_interface() also needs some time cost because
the previous 11d scan need more than 5 seconds when 6 GHz is enabled,
then the scan started event will indicated to ath11k after the 11d
scan completed.

While 11d scan/hw scan is running in firmware, if ath11k update channel
list to firmware by WMI_SCAN_CHAN_LIST_CMDID, then firmware will cancel
the current scan which is running, it lead the scan failed. The patch
commit 9dcf6808 ("ath11k: add 11d scan offload support") used
finish_11d_scan/finish_11d_ch_list/pending_11d to synchronize the 11d
scan/hw scan/channel list between ath11k/firmware/mac80211 and to avoid
the scan fail.

Add wait operation before ath11k update channel list, function
ath11k_reg_update_chan_list() will wait until the current 11d scan/hw
scan completed. And remove the wait operation of start 11d scan and
waiting channel list complete in hw scan. After these changes, resume
time cost reduce about 5 seconds and also hw scan time cost reduced
obviously, and scan failed not seen.

The 11d scan is sent to firmware only one time for each interface added
in mac.c, and it is moved after the 1st hw scan because 11d scan will
cost some time and thus leads the AP scan result update to UI delay.
Currently priority of ath11k's hw scan is WMI_SCAN_PRIORITY_LOW, and
priority of 11d scan in firmware is WMI_SCAN_PRIORITY_MEDIUM, then the
11d scan which sent after hw scan will cancel the hw scan in firmware,
so change the priority to WMI_SCAN_PRIORITY_MEDIUM for the hw scan which
is in front of the 11d scan, thus it will not happen scan cancel in
firmware.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Fixes: 9dcf6808 ("ath11k: add 11d scan offload support")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328035832.14122-1-quic_wgong@quicinc.com

Currently ath11k only download the same regdb.bin file for all WCN6855
chips, actually ath11k needs to distinguish all different WCN6855 chips.

This is to re-use the string type which include bus, chip id, board id,
vendor, device, subsystem-vendor, subsystem-device and variant for
WCN6855 to distinguish different regdb in board-2.bin.

ath11k will first load board-2.bin and search in it for the regdb data
with the above parameters, if matched one regdb data, then download it
to firmware, if not matched any one, then ath11k will download the file
regdb.bin to firmware.

Add enum value ATH11K_BD_IE_REGDB and enum type ath11k_bd_ie_regdb_type
to distinguish regdb data and board data since they are in the same file
board-2.bin.

This only take effect for WCN6855 which supports regdb in hardware parameters.

Test log:
[ 3833.091948] ath11k_pci 0000:05:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[ 3833.092072] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 205316
[ 3833.092079] ath11k_pci 0000:05:00.0: board name
[ 3833.092083] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70  bus=pci,qmi-chip
[ 3833.092088] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 31                                   -id=1
[ 3833.092091] ath11k_pci 0000:05:00.0: board name
[ 3833.092095] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70  bus=pci,qmi-chip
[ 3833.092099] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 32                                   -id=2
[ 3833.092102] ath11k_pci 0000:05:00.0: board name
[ 3833.092105] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70  bus=pci,qmi-chip
[ 3833.092109] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 33                                   -id=3
[ 3833.092112] ath11k_pci 0000:05:00.0: board name
[ 3833.092116] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31  bus=pci,vendor=1
[ 3833.092119] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c  7cb,device=1103,
[ 3833.092123] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72  subsystem-vendor
[ 3833.092126] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d  =17cb,subsystem-
[ 3833.092130] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d  device=3374,qmi-
[ 3833.092133] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f  chip-id=2,qmi-bo
[ 3833.092137] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 36 2c 76 61 72 69 61  ard-id=266,varia
[ 3833.092140] ath11k_pci 0000:05:00.0: 00000070: 6e 74 3d 48 50 5f 47 38 5f 4c 61 6e 63 69 61 31  nt=HP_G8_Lancia1
[ 3833.092144] ath11k_pci 0000:05:00.0: 00000080: 35                                               5
[ 3833.092147] ath11k_pci 0000:05:00.0: board name
[ 3833.092150] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31  bus=pci,vendor=1
[ 3833.092154] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c  7cb,device=1103,
[ 3833.092157] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72  subsystem-vendor
[ 3833.092161] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d  =17cb,subsystem-
[ 3833.092165] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d  device=3374,qmi-
[ 3833.092168] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f  chip-id=2,qmi-bo
[ 3833.092172] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 36                    ard-id=266
[ 3833.092206] ath11k_pci 0000:05:00.0: board name
[ 3833.092209] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31  bus=pci,vendor=1
[ 3833.092213] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c  7cb,device=1103,
[ 3833.092216] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72  subsystem-vendor
[ 3833.092220] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d  =17cb,subsystem-
[ 3833.092223] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d  device=3374,qmi-
[ 3833.092227] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f  chip-id=2,qmi-bo
[ 3833.092230] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 32                    ard-id=262
[ 3833.092234] ath11k_pci 0000:05:00.0: boot found match regdb data for name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[ 3833.092238] ath11k_pci 0000:05:00.0: board name
[ 3833.092241] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70  bus=pci,qmi-chip
[ 3833.092245] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 31 31                                -id=11
[ 3833.092248] ath11k_pci 0000:05:00.0: board name
[ 3833.092251] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70  bus=pci,qmi-chip
[ 3833.092255] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 32 32                                -id=22
[ 3833.092258] ath11k_pci 0000:05:00.0: board name
[ 3833.092261] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 71 6d 69 2d 63 68 69 70  bus=pci,qmi-chip
[ 3833.092265] ath11k_pci 0000:05:00.0: 00000010: 2d 69 64 3d 33 33                                -id=33
[ 3833.092268] ath11k_pci 0000:05:00.0: boot found regdb data for 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[ 3833.092272] ath11k_pci 0000:05:00.0: fetched regdb

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220319023543.14288-4-quic_wgong@quicinc.com

Currently, the driver reports a tx_rate of 6.0 MBit/s no matter the true
rate:

root@linaro-developer:~# iw wlan0 link
Connected to 6c:f3:7f:eb:9b:92 (on wlan0)
        SSID: SQ-DEVICETEST
        freq: 5200
        RX: 4141 bytes (32 packets)
        TX: 2082 bytes (15 packets)
        signal: -77 dBm
        rx bitrate: 135.0 MBit/s MCS 6 40MHz short GI
        tx bitrate: 6.0 MBit/s

        bss flags:      short-slot-time
        dtim period:    1
        beacon int:     100

This patch requests HAL_GLOBAL_CLASS_A_STATS_INFO via a hal_get_stats
firmware message and reports it via ieee80211_ops::sta_statistics.

root@linaro-developer:~# iw wlan0 link
Connected to 6c:f3:7f:eb:73:b2 (on wlan0)
        SSID: SQ-DEVICETEST
        freq: 5700
        RX: 26788094 bytes (19859 packets)
        TX: 1101376 bytes (12119 packets)
        signal: -75 dBm
        rx bitrate: 135.0 MBit/s MCS 6 40MHz short GI
        tx bitrate: 108.0 MBit/s VHT-MCS 5 40MHz VHT-NSS 1

        bss flags:      short-slot-time
        dtim period:    1
        beacon int:     100

Tested on MSM8939 with WCN3680B running firmware CNSS-PR-2-0-1-2-c1-00083,
and verified by sniffing frames over the air with Wireshark to ensure the
MCS indices match.
Signed-off-by: Edmond Gagnon <egagnon@squareup.com>
Reviewed-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220325224212.159690-1-egagnon@squareup.com

Currently ath11k does not send the country code to firmware after device
recovery, as a result the regdomain info is reported from firmware by
default. Regdomain info is important, so ath11k also need to restore
it to the value which was used before recovery.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220324011856.11014-1-quic_wgong@quicinc.com

This removes some code duplication with le32_to_cpu. This may also be
required for QCN550x support, to provide an abstraction over the
underlying EEPROM format.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-7-wlooi@ucalgary.ca

Similar to ar9003_hw_spur_mitigate_mrc_cck, simplify the code by using
ar9003_get_spur_chan_ptr. This may also be required for QCN550x support,
to provide an abstraction over the underlying EEPROM format.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-6-wlooi@ucalgary.ca

The current implementation is reading the wrong eeprom type.

Fixes: d8ec2e2a ("ath9k: Add an eeprom_ops callback for retrieving the eepmisc value")
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-5-wlooi@ucalgary.ca

Replace other constants with AR9300_MAX_CHAINS when appropriate.

This change does not appear to affect the final binary.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-4-wlooi@ucalgary.ca

This makes the code clearer since set11nRateFlags currently sets
both the rate flags and chain sel. This may also be required for
QCN550x support, where the rate flags and chain sel are in separate
fields.

This change does not appear to affect the final binary.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-3-wlooi@ucalgary.ca

This makes the macros more consistent and removes hidden dependencies on
ah for macros that take _ah as a parameter.

This change does not appear to affect the final binary.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-2-wlooi@ucalgary.ca

When more clients (128) are connected, the UL data traffic
KPI measurement is low compared to single client. This issue
is due to more CPU cycles spent on the peer lookup operation
with more clients. So reduce the peer lookup operation by
modifying the linear based lookup operation into the rhash
based lookup operation. This improve the peak throughput
measurement. Since this is a software algorithm change, it is
applicable for all the platforms.

TCP UL 128 Clients test case Observation (64bit system):
Previous: ~550 Mbps
Now	: ~860 Mbps

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644036628-5334-1-git-send-email-quic_periyasa@quicinc.com

This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220315104721.26649-3-quic_wgong@quicinc.com

Sometimes it has a variant value which read from DT or SMBIOS by
ath11k, and meanwhile it does not have the matched board name in
board-2.bin, then it will failed at boot up phase.

Add fallback board name which removed variant value and search again
in board-2.bin when failed with variant and try to load the board
data again to increase boot up success rate.

dmesg log after this patch:
[169547.248472] ath11k_pci 0000:05:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262,variant=test'
[169547.248565] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 180324
[169547.248568] ath11k_pci 0000:05:00.0: board name
[169547.248570] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31  bus=pci,vendor=1
[169547.248571] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c  7cb,device=1103,
[169547.248572] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72  subsystem-vendor
[169547.248574] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d  =17cb,subsystem-
[169547.248575] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d  device=3374,qmi-
[169547.248576] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f  chip-id=2,qmi-bo
[169547.248577] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 32                    ard-id=262
[169547.248578] ath11k_pci 0000:05:00.0: board name
[169547.248579] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31  bus=pci,vendor=1
[169547.248581] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c  7cb,device=1103,
[169547.248582] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72  subsystem-vendor
[169547.248583] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d  =17cb,subsystem-
[169547.248584] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d  device=3374,qmi-
[169547.248585] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f  chip-id=2,qmi-bo
[169547.248587] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 36                    ard-id=266
[169547.248588] ath11k_pci 0000:05:00.0: board name
[169547.248589] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31  bus=pci,vendor=1
[169547.248590] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c  7cb,device=1103,
[169547.248591] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72  subsystem-vendor
[169547.248592] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d  =17cb,subsystem-
[169547.248594] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d  device=3374,qmi-
[169547.248595] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 31 38 2c 71 6d 69 2d 62  chip-id=18,qmi-b
[169547.248596] ath11k_pci 0000:05:00.0: 00000060: 6f 61 72 64 2d 69 64 3d 32 36 36                 oard-id=266
[169547.248597] ath11k_pci 0000:05:00.0: failed to fetch board data for bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262,variant=test from ath11k/WCN6855/hw2.0/board-2.bin
[169547.248476] ath11k_pci 0000:05:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[169547.248634] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 180324
[169547.248636] ath11k_pci 0000:05:00.0: board name
[169547.248637] ath11k_pci 0000:05:00.0: 00000000: 62 75 73 3d 70 63 69 2c 76 65 6e 64 6f 72 3d 31  bus=pci,vendor=1
[169547.248638] ath11k_pci 0000:05:00.0: 00000010: 37 63 62 2c 64 65 76 69 63 65 3d 31 31 30 33 2c  7cb,device=1103,
[169547.248639] ath11k_pci 0000:05:00.0: 00000020: 73 75 62 73 79 73 74 65 6d 2d 76 65 6e 64 6f 72  subsystem-vendor
[169547.248641] ath11k_pci 0000:05:00.0: 00000030: 3d 31 37 63 62 2c 73 75 62 73 79 73 74 65 6d 2d  =17cb,subsystem-
[169547.248642] ath11k_pci 0000:05:00.0: 00000040: 64 65 76 69 63 65 3d 33 33 37 34 2c 71 6d 69 2d  device=3374,qmi-
[169547.248643] ath11k_pci 0000:05:00.0: 00000050: 63 68 69 70 2d 69 64 3d 32 2c 71 6d 69 2d 62 6f  chip-id=2,qmi-bo
[169547.248645] ath11k_pci 0000:05:00.0: 00000060: 61 72 64 2d 69 64 3d 32 36 32                    ard-id=262
[169547.248646] ath11k_pci 0000:05:00.0: boot found match for name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[169547.248647] ath11k_pci 0000:05:00.0: boot found board data for 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
[169547.248649] ath11k_pci 0000:05:00.0: using board api 2

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220315104721.26649-2-quic_wgong@quicinc.com

In Qualcomm ARM platforms there is WL_EN pin and other power regulators
which can be controlled at platform side to completely reset the chip.
For most of x86 and other platforms, the chip is connected via PCIe M.2
interface, and there is no way to control WL_EN pin. Instead the host
driver needs to reset the chip via PCIE_SOC_GLOBAL_RESET hardware
register, just like ath11k does currently.

But when using PCIE_SOC_GLOBAL_RESET there are some hardware registers
which are not cleared/restored. To handle those cases we can enable
PLATFORM_CAP_PCIE_GLOBAL_RESET QMI host capability to tell the firmware
to do some platform specific operations after firmware download.

This does not fix any known issues, but is recommended by the firmware
team, so enable the capability on QCA6390 and WCN6855 PCI devices. It is
currently unclear if this should be enabled also on QCN9074, so leave it
disabled for now. On AHB devices this is not needed as they don't use
PCIE_SOC_GLOBAL_RESET.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211011055602.77342-1-bqiang@codeaurora.org

When test device recovery with below command, it has warning in message
as below.
echo assert > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash
echo assert > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash

warning message:
[ 1965.642121] ath11k_pci 0000:06:00.0: simulating firmware assert crash
[ 1968.471364] ieee80211 phy0: Hardware restart was requested
[ 1968.511305] ------------[ cut here ]------------
[ 1968.511368] WARNING: CPU: 3 PID: 1546 at drivers/bus/mhi/core/pm.c:505 mhi_pm_disable_transition+0xb37/0xda0 [mhi]
[ 1968.511443] Modules linked in: ath11k_pci ath11k mac80211 libarc4 cfg80211 qmi_helpers qrtr_mhi mhi qrtr nvme nvme_core
[ 1968.511563] CPU: 3 PID: 1546 Comm: kworker/u17:0 Kdump: loaded Tainted: G        W         5.17.0-rc3-wt-ath+ #579
[ 1968.511629] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0067.2021.0528.1339 05/28/2021
[ 1968.511704] Workqueue: mhi_hiprio_wq mhi_pm_st_worker [mhi]
[ 1968.511787] RIP: 0010:mhi_pm_disable_transition+0xb37/0xda0 [mhi]
[ 1968.511870] Code: a9 fe ff ff 4c 89 ff 44 89 04 24 e8 03 46 f6 e5 44 8b 04 24 41 83 f8 01 0f 84 21 fe ff ff e9 4c fd ff ff 0f 0b e9 af f8 ff ff <0f> 0b e9 5c f8 ff ff 48 89 df e8 da 9e ee e3 e9 12 fd ff ff 4c 89
[ 1968.511923] RSP: 0018:ffffc900024efbf0 EFLAGS: 00010286
[ 1968.511969] RAX: 00000000ffffffff RBX: ffff88811d241250 RCX: ffffffffc0176922
[ 1968.512014] RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffff888118a90a24
[ 1968.512059] RBP: ffff888118a90800 R08: 0000000000000000 R09: ffff888118a90a27
[ 1968.512102] R10: ffffed1023152144 R11: 0000000000000001 R12: ffff888118a908ac
[ 1968.512229] R13: ffff888118a90928 R14: dffffc0000000000 R15: ffff888118a90a24
[ 1968.512310] FS:  0000000000000000(0000) GS:ffff888234200000(0000) knlGS:0000000000000000
[ 1968.512405] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1968.512493] CR2: 00007f5538f443a8 CR3: 000000016dc28001 CR4: 00000000003706e0
[ 1968.512587] Call Trace:
[ 1968.512672]  <TASK>
[ 1968.512751]  ? _raw_spin_unlock_irq+0x1f/0x40
[ 1968.512859]  mhi_pm_st_worker+0x3ac/0x790 [mhi]
[ 1968.512959]  ? mhi_pm_mission_mode_transition.isra.0+0x7d0/0x7d0 [mhi]
[ 1968.513063]  process_one_work+0x86a/0x1400
[ 1968.513184]  ? pwq_dec_nr_in_flight+0x230/0x230
[ 1968.513312]  ? move_linked_works+0x125/0x290
[ 1968.513416]  worker_thread+0x6db/0xf60
[ 1968.513536]  ? process_one_work+0x1400/0x1400
[ 1968.513627]  kthread+0x241/0x2d0
[ 1968.513733]  ? kthread_complete_and_exit+0x20/0x20
[ 1968.513821]  ret_from_fork+0x22/0x30
[ 1968.513924]  </TASK>

Reason is mhi_deassert_dev_wake() from mhi_device_put() is called
but mhi_assert_dev_wake() from __mhi_device_get_sync() is not called
in progress of recovery. Commit 8e055992 ("bus: mhi: core:
Skip device wake in error or shutdown state") add check for the
pm_state of mhi in __mhi_device_get_sync(), and the pm_state is not
the normal state untill recovery is completed, so it leads the
dev_wake is not 0 and above warning print in mhi_pm_disable_transition()
while checking mhi_cntrl->dev_wake.

Add check in ath11k_pci_write32()/ath11k_pci_read32() to skip call
mhi_device_put() if mhi_device_get_sync() does not really do wake,
then the warning gone.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-5-quic_wgong@quicinc.com

Add hw-restart to directly restart wlan. Like UTF mode start it will
restart hardware and download firmware again.

Usage:
1. Run command:
   echo hw-restart > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash
   echo hw-restart > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash
2. wlan will be restart and do recovery process and success.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-4-quic_wgong@quicinc.com

ieee80211_reconfig() of mac80211 is the main function for recovery of
each ieee80211_hw and ath11k, and ath11k_core_reconfigure_on_crash()
is the main function for recovery of ath11k_base, it has more than
one ieee80211_hw and ath11k for each ath11k_base, so it need to add
synchronization between them, otherwise it has many issue.

For example, when ath11k_core_reconfigure_on_crash() is not complete,
mac80211 send a hw scan request to ath11k, it leads firmware crash,
because firmware has not been initialized at that moment, firmware
is only finished downloaded and loaded, it can not receive scan
command.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-3-quic_wgong@quicinc.com

Currently ath11k has device recovery logic, it is introduced by this
patch "ath11k: Add support for subsystem recovery" which is upstream
by https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git/commit/?h=ath11k-bringup&id=3a7b4838b6f6f234239f263ef3dc02e612a083ad.

The patch is for AHB devices such as IPQ8074, it has remote proc module
which is used to download the firmware and boots the processor which
firmware is running on. If firmware crashed, remote proc module will
detect it and download and boot firmware again. Below command will
trigger a firmware crash, and then user can test feature of device
recovery.

Test command:
echo assert > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash
echo assert > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash

Unfortunately, QCA6390 is PCIe bus, it does not have the remote proc
module, it use mhi module to communicate between firmware and ath11k.
So ath11k does not support device recovery for QCA6390 currently.

This patch is to add the extra logic which is different for QCA6390.
When firmware crashed, MHI_CB_EE_RDDM event will be indicate by
firmware and then ath11k_mhi_op_status_cb which is the callback of
mhi_controller will receive the MHI_CB_EE_RDDM event, then ath11k
will start to do recovery process, ath11k_core_reset() calls
ath11k_hif_power_down()/ath11k_hif_power_up(), then the mhi/ath11k
will start to download and boot firmware. There are some logic to
avoid deadloop recovery and two simultaneous recovery operations.
And because it has muti-radios for the soc, so it add some logic
in ath11k_mac_op_reconfig_complete() to make sure all radios has
reconfig complete and then complete the device recovery.

Also it add workqueue_aux, because ab->workqueue is used when receive
ATH11K_QMI_EVENT_FW_READY in recovery process(queue_work(ab->workqueue,
&ab->restart_work)), and ath11k_core_reset will wait for max
ATH11K_RESET_TIMEOUT_HZ for the previous restart_work finished, if
ath11k_core_reset also queued in ab->workqueue, then it will delay
restart_work of previous recovery and lead previous recovery fail.

ath11k recovery success for QCA6390/WCN6855 after apply this patch.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-2-quic_wgong@quicinc.com

Currently it does not have regdb files for QCA6390, so disable its regdb
support feature now.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220319023543.14288-3-quic_wgong@quicinc.com

Currently ATH11K_BD_IE_BOARD_EXT is not used, so remove it.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220319023543.14288-2-quic_wgong@quicinc.com

ath11k_peer_find_by_addr states via lockdep that ab->base_lock must be
held when calling that function in order to protect the list. All
callers except ath11k_mac_op_unassign_vif_chanctx have that lock
acquired when calling ath11k_peer_find_by_addr. That lock is also not
transitively held by a path towards ath11k_mac_op_unassign_vif_chanctx.
The solution is to acquire the lock when calling
ath11k_peer_find_by_addr inside ath11k_mac_op_unassign_vif_chanctx.

I am currently working on a static analyser to detect missing locks and
this was a reported case. I manually verified the report by looking at
the code, but I do not have real hardware so this is compile tested
only.

Fixes: 701e48a4 ("ath11k: add packet log support for QCA6390")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220314215253.92658-1-dossche.niels@gmail.com

Currently fw build id is printed during init as follows.

fw_version 0x250684a5 fw_build_timestamp 2021-07-13 10:57
fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1

The string "QC_IMAGE_VERSION_STRING=" is removed from the log
to improve readability.

With this patch the fw build id is printed during init as follows.
fw_version 0x250684a5 fw_build_timestamp 2021-07-13 10:57
fw_build_id WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1646825065-7736-1-git-send-email-quic_haric@quicinc.com

Introduce new helper function for peer delete to reuse this logic
in all peer cleanup procedures. Found this in code review.
Also this change is applicable for all the platform.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1646024079-26391-1-git-send-email-quic_periyasa@quicinc.com

Only the device data is needed, not the entire struct of_device_id.
Use of_device_get_match_data() instead of of_match_device().
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220318025331.23030-1-tangmeng@uniontech.com

Currently after the hardware restart triggered from the driver,
the station interface connection remains intact, since a disconnect
trigger is not sent to userspace. This can lead to a problem in
targets where the wifi mac sequence is added by the firmware.

After the target restart, its wifi mac sequence number gets
reset to zero. Hence AP to which our device is connected will receive
frames with a  wifi mac sequence number jump to the past, thereby
resulting in the AP dropping all these frames, until the frame
arrives with a wifi mac sequence number which AP was expecting.

To avoid such frame drops, its better to trigger a station disconnect
upon target hardware restart which can be done with API
ieee80211_reconfig_disconnect exposed to mac80211.

The other targets are not affected by this change, since the hardware
params flag is not set.

Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220315082944.12406-3-youghand@codeaurora.org

Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220314115354.144023-4-Julia.Lawall@inria.fr

It is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ)
for requesting IRQ's resources any more, as they can be not ready yet in
case of DT-booting.

platform_get_irq() instead is a recommended way for getting IRQ even if
it was not retrieved earlier.

It also makes code simpler because we're getting "int" value right away
and no conversion from resource to int is required.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220314064501.2114002-1-chi.minghao@zte.com.cn

Host sets GTK related info to firmware before WoW is enabled, and
gets rekey replay_count and then disables GTK rekey when WoW quits.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-7-git-send-email-quic_cjhuang@quicinc.com

Support ARP and NS offload in WoW state.

Tested this way: put machine A with QCA6390 to WoW state,
ping/ping6 machine A from another machine B, check sniffer to see
any ARP response and Neighbour advertisement from machine A.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-6-git-send-email-quic_cjhuang@quicinc.com

This change is to purge rx pktlog when entering WoW and reap
the mon_status buffer to keep it empty. When leaving WoW, host
restarts the reap timer. In WoW state, it's not allowed to feed
into mon_status rings per firmware team's recommendation.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-5-git-send-email-quic_cjhuang@quicinc.com