On 57500 chips, the original bnxt_cp_ring_info struct now refers to the
NQ.  bp->cp_nr_rings refer to the number of NQs on 57500 chips.  There
are now 2 pointers for the CP rings associated with RX and TX rings.
Modify bnxt_alloc_cp_rings() and bnxt_free_cp_rings() accordingly.

With multiple CP rings per NAPI, we need to add a pointer in
bnxt_cp_ring_info struct to point back to the bnxt_napi struct.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ring reservation functions have to be modified for P5 chips in the
following ways:

- bnxt_cp_ring_info structs map to internal NQs as well as CP rings.
- Ring groups are not used.
- 1 CP ring must be available for each RX or TX ring.
- number of RSS contexts to reserve is multiples of 64 RX rings.
- RFS currently not supported.

Also, RX AGG rings are only used for jumbo frames, so we need to
unconditionally call bnxt_reserve_rings() in __bnxt_open_nic()
to see if we need to reserve AGG rings in case MTU has changed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Store the maximum MSIX capability in PCIe config. space earlier.  When
we call firmware to query capability, we need to compare the PCIe
MSIX max count with the firmware count and use the smaller one as
the MSIX count for 57500 (P5) chips.

The new chips don't use ring groups.  But previous chips do and
the existing logic limits the available rings based on resource
calculations including ring groups.  Setting the max ring groups to
the max rx rings will work on the new chips without changing the
existing logic.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 57500 series chips have a new 64-bit doorbell format.  Use a new
bnxt_db_info structure to unify the new and the old 32-bit doorbells.
Add a new bnxt_set_db() function to set up the doorbell addreses and
doorbell keys ahead of time.  Modify and introduce new doorbell
helpers to help abstract and unify the old and new doorbells.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

57500 series is a new chip class (P5) that requires some driver changes
in the next several patches.  This adds basic chip ID, doorbells, and
the notification queue (NQ) structures.  Each MSIX is associated with an
NQ instead of a CP ring in legacy chips.  Each NQ has up to 2 associated
CP rings for RX and TX.  The same bnxt_cp_ring_info struct will be used
for the NQ.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call firmware to configure the DMA addresses of all context memory
pages on new devices requiring context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New device requires host context memory as a backing store.  Call
firmware to check for context memory requirements and store the
parameters.  Allocate host pages accordingly.

We also need to move the call bnxt_hwrm_queue_qportcfg() earlier
so that all the supported hardware queues and the IDs are known
before checking and allocating context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer chips require the PTU_PTE_VALID bit to be set for every page
table entry for context memory and rings.  Additional bits are also
required for page table entries for all rings.  Add a flags field to
bnxt_ring_mem_info struct to specify these additional bits to be used
when setting up the pages tables as needed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the DMA page table and vmem fields in bnxt_ring_struct to a new
bnxt_ring_mem_info struct.  This will allow context memory management
for a new device to re-use some of the existing infrastructure.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New firmware spec. allows interrupt coalescing parameters, such as
maximums, timer units, supported features to be queried.  Update
the driver to make use of the new call to query these parameters
and provide the legacy defaults if the call is not available.

Replace the hard-coded values with these parameters.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support the max_ext_req_len field from the HWRM_VER_GET_RESPONSE.
If this field is valid and greater than the mailbox size, use the
short command format to send firmware messages greater than the
mailbox size.  Newer devices use this method to send larger messages
to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Latest firmware spec. has some additional rx extended port stats and new
tx extended port stats added.  We now need to check the size of the
returned rx and tx extended stats and determine how many counters are
valid.  New counters added include CoS byte and packet counts for rx
and tx.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Among the new changes are trusted VF support, 200Gbps support, and new
API to dump ring information on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefano Brivio says:

====================
selftests: pmtu: Add test choice and captures

This series adds a couple of features useful for debugging: 1/2
allows selecting single tests and 2/2 adds optional traffic
captures.

Semantics for current invocation of test script are preserved.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If --trace is passed as an option and tcpdump is available,
capture traffic for all relevant interfaces to per-test pcap
files named <test>_<interface>.pcap.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

As number of tests is growing, it's quite convenient to allow
single tests to be run.

Display usage when the script is run with any invalid argument,
keep existing semantics when no arguments are passed so that
automated runs won't break.

Instead of just looping on the list of requested tests, if any,
check first that they exist, and go through them in a nested
loop to keep the existing way to display test descriptions.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_device_detach() stops all tx queues already, so we don't need
this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify this function, no functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The newly added driver causes a warning about a function that is
not used anywhere:

drivers/net/ethernet/marvell/octeontx2/af/cgx.c:320:12: error: 'cgx_fwi_link_change' defined but not used [-Werror=unused-function]

Remove it for now, until a user gets added. If we want to use this
function from another module, we also need a declaration in a header
file, which is currently missing, so it would have to change anyway.

Fixes: 1463f382 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit makes it possible to use devlink to split the 100G CXP
Netronome into two 40G interfaces. Currently when you ask for 2
interfaces, the math in src/nfp_devlink.c:nfp_devlink_port_split
calculates that you want 5 lanes per port because for some reason
eth_port.port_lanes=10 (shouldn't this be 12 for CXP?). What we really
want when asking for 2 breakout interfaces is 4 lanes per port. This
commit makes that happen by calculating based on 8 lanes if 10 are
present.
Signed-off-by: Ryan C Goodfellow <rgoodfel@isi.edu>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Greg Weeks <greg.weeks@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
dpaa2-eth: code cleanup

There are no functional changes in this patch set, only some cleanup
changes such as: unused parameters, uninitialized variables and
unnecessary Kconfig dependencies.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the hardware ArchDef, the PTV1 field in FD[CTRL]
is ignored by WRIOP, so setting it for Tx FDs is pointless.

Remove all references to it from the code.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ch parameter is never used in the dpaa2_eth_tx_conf function but
since its prototype must match the type defined in the consume field of
struct dpaa2_eth_fq, just mark it as __always_unused.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The priv parameter is never used in the build_linear_skb and
drain_channel function. Remove it from the function definitions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All 3 cases of possible uninitialized variables are false
positives since they are used only as output parameters.
Nonetheless, fix the warnings.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dpaa2_eth_set_dist_key function is only used in a single file.
Make it static.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both ARCH_LAYERSCAPE and COMPILE_TEST dependencies are already implied
through the FSL_MC_BUS dep, so there's no need to state it explicitly.

Also, the fsl-mc bus depends on COMPILE_TEST only for some
architectures (arm, arm64, ppc, x86), so it's not correct to
claim build support unconditionally.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In dual-emac mode the cpsw driver sends directed packets, that means
that packets go to the directed port, but an ALE lookup is performed
to determine untagged egress only. It means that on tx side no need
to add port bit for ALE mcast entry mask, and basically ALE entry
for port identification is needed only on rx side.

So, add only host port in dual_emac mode as used directed
transmission, and no need in one more port. For single port boards
and switch mode all ports used, as usual, so no changes for them.
Also it simplifies farther changes.

In other words, mcast entries for dual-emac should behave exactly
like unicast. It also can help avoid leaking packets between ports
with same vlan on h/w level if ports could became members of same vid.

So now, for instance, if mcast address 33:33:00:00:00:01 is added then
entries in ALE table:

vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x1
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x1

Instead of:
vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x3
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x5

With the same considerations, set only host port for unregistered
mcast for dual-emac mode in case of IFF_ALLMULTI is set, exactly like
it's done in cpsw_ale_set_allmulti().
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ivan Khoronzhuk says:

====================
net: ethernet: ti: cpsw fix mcast packet lost

The patchset omits redundant refresh of mcast address table and
prevents mcast packet lost.

Based on net-next/master
tested on am572x evm
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever kernel or user decides to call rx mode update, it clears
every multicast entry from forwarding table and in some time adds
it again. This time can be enough to drop incoming multicast packets.

That's why clear only staled multicast entries and update or add new
one afterwards.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It allows to use function under callbacks with same const qualifier of
mac address for farther changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: improve and simplify state machine

Improve / simplify handling of states PHY_RUNNING and PHY_RESUMING in
phylib state machine.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify code for handling state PHY_RESUMING, no functional change
intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handling of state PHY_RUNNING seems to be more complex than it needs
to be. If not polling, then we don't have to do anything, we'll
receive an interrupt and go to state PHY_CHANGELINK once the link
goes down. If polling and link is down, we don't have to go the
extra mile over PHY_CHANGELINK and call phy_read_status() again
but can set status PHY_NOLINK directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes use of NTF_USE in vxlan driver consistent
with bridge driver.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new command (NCSI_CMD_SEND_CMD) is added to allow user space application
to send NC-SI command to the network card.
Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response.

The work flow is as below.

Request:
User space application
	-> Netlink interface (msg)
	-> new Netlink handler - ncsi_send_cmd_nl()
	-> ncsi_xmit_cmd()

Response:
Response received - ncsi_rcv_rsp()
	-> internal response handler - ncsi_rsp_handler_xxx()
	-> ncsi_rsp_handler_netlink()
	-> ncsi_send_netlink_rsp ()
	-> Netlink interface (msg)
	-> user space application

Command timeout - ncsi_request_timeout()
	-> ncsi_send_netlink_timeout ()
	-> Netlink interface (msg with zero data length)
	-> user space application

Error:
Error detected
	-> ncsi_send_netlink_err ()
	-> Netlink interface (err msg)
	-> user space application
Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When starting the state machine there may be work to be done
immediately, e.g. if the initial state is PHY_UP then the state
machine may trigger an autonegotiation. Having said that I see no need
to wait a second until the state machine is run first time.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Toshiaki Makita says:

====================
veth: XDP stats improvement

ndo_xdp_xmit in veth did not update packet counters as described in [1].
Also, current implementation only updates counters on tx side so rx side
events like XDP_DROP were not collected.
This series implements the missing accounting as well as support for
ethtool per-queue stats in veth.

Patch 1: Update drop counter in ndo_xdp_xmit.
Patch 2: Update packet and byte counters for all XDP path, and drop
         counter on XDP_DROP.
Patch 3: Support per-queue ethtool stats for XDP counters.

Note that counters are maintained on per-queue basis for XDP but not
otherwise (per-cpu and atomic as before). This is because 1) tx path in
veth is essentially lockless so we cannot update per-queue stats on tx,
and 2) rx path is net core routine (process_backlog) which cannot update
per-queue based stats when XDP is disabled. On the other hand there are
real rxqs and napi handlers for veth XDP, so update per-queue stats on
rx for XDP packets, and use them to calculate tx counters as well,
contrary to the existing non-XDP counters.

[1] https://patchwork.ozlabs.org/cover/953071/#1967449
====================
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose per-queue stats for ethtool -S.
As there are only rx queues, and rx queues are used only when XDP is
used, per-queue counters are only rx XDP ones.

Example:

$ ethtool -S veth0
NIC statistics:
     peer_ifindex: 11
     rx_queue_0_xdp_packets: 28601434
     rx_queue_0_xdp_bytes: 1716086040
     rx_queue_0_xdp_drops: 28601434
     rx_queue_1_xdp_packets: 17873050
     rx_queue_1_xdp_bytes: 1072383000
     rx_queue_1_xdp_drops: 17873050
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

On XDP path veth has napi handler so we can collect statistics on
per-queue basis for XDP.

By this change now we can collect XDP_DROP drop count as well as packets
and bytes coming through ndo_xdp_xmit. Packet counters shown by
"ip -s link", sysfs stats or /proc/net/dev is now correct for XDP.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>