On review of 'zd1211rw: implement beacon fetching and handling
ieee80211_get_buffered_bc()', Christian Lamparter noted that [1]:

   Since zd_beacon_done also uploads the next beacon so long in advance,
   there could be an equally long race between the outdated state of the
   next beacon's DTIM broadcast traffic indicator (802.11-2007 7.3.2.6)
   which -in your case- was uploaded almost a beacon interval ago and
   the xmit of ieee80211_get_buffered_bc *now*.

   The dtim bc/mc bit might be not set, when a mc/bc arrived after the
   beacon was uploaded, but before the "beacon done event" from the
   hardware. So, dozing stations don't expect the broadcast traffic
   and of course, they might miss it completely.

   It's probably better to fix this in mac80211 (see the attached hack).

[1] http://marc.info/?l=linux-wireless&m=129435041117256&w=2

CC: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support for AP-mode beacon. Also disable beacon when interface is set
down as otherwise hw will keep flooding NEXT_BCN interrupts.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For reasons not very clear yet to me, filter_ack leaves matching tx-packet
pending with 'ack_pending'. This causes tx-packet to be passed back to upper
layer after next packet has been transfered and tx-packets might end up
coming come out of monitor interface in wrong order vs. rx.

Because of this when enable AP-mode, hostapd monitor interface would get
packets in wrong order causing problems in WPA association.

So don't use mac->ack_pending when in AP-mode.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As bss_info_changed may sleep, we can as well set RTS_CTS register right away.
Keep mac->short_preamble for later use (hw reset).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Workers not needed anymore since configure_filter may sleep. Keep
mac->multicast_hash for later use (hw reset).
Signed-off-by: Jussi Kivilinna <jussi.kivilina@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Vendor driver uses CR_BNC_INTERVAL at various places, one is HW_EnableBeacon()
that combinies beacon interval with BSS-type flag and DTIM value in upper 16bit
of u32. The other one is HW_UpdateBcnInterval() that set_aw_pt_bi()
appears to be based on. HW_UpdateBcnInterval() takes interval argument as u16
and uses that for calculations, set_aw_pt_bi() uses u32 value that has flags
and dtim in upper part. This clearly seems wrong. Also HW_UpdateBcnInterval()
updates only lower 16bit part of CR_BNC_INTERVAL. So make set_aw_pt_bi() do
calculations on only lower u16 part of s->beacon_interval.

Also set 32bit beacon interval register before reading values from device,
as HW_EnableBeacon() on vendor driver does. This is required to make beacon
work on AP-mode, simply reading and then writing updated values is not enough
at least with zd1211b.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

OOPS if worker is running and disconnect() is called (triggered
by unpluging device). Much harder to trigger at this stage but
later when we have AP beacon work in process_intr it happens very
easy.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When stress testing AP-mode I hit OOPS when unpluging or rmmodding
driver.

It appears that when tx-queue is disabled, tx-urbs might be left pending.
These can cause ehci to call non-existing tx_urb_complete() (after rmmod)
or uninitialized/reseted private structure (after disconnect()). Add skb
queue for submitted packets and unlink pending urbs on zd_usb_disable_tx().

Part of the problem seems to be usb->free_urb_list that isn't always
working as it should, causing machine freeze when trying to free the list
in zd_usb_disable_tx(). Caching free urbs isn't what other drivers seem
to be doing (usbnet for example) so strip free_usb_list.

Patch makes tx-urb handling saner with use of urb anchors.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TKIP countermeasures depend on devices being able to detect Michael
MIC failures on received frames and for stations to report errors to
the AP. In order to test that behavior, it is useful to be able to
send out TKIP frames with incorrect Michael MIC. This testing behavior
has minimal effect on the TX path, so it can be added to mac80211 for
convenient use.

The interface for using this functionality is a file in mac80211
netdev debugfs (tkip_mic_test). Writing a MAC address to the file
makes mac80211 generate a dummy data frame that will be sent out using
invalid Michael MIC value. In AP mode, the address needs to be for one
of the associated stations or ff:ff:ff:ff:ff:ff to use a broadcast
frame. In station mode, the address can be anything, e.g., the current
BSSID. It should be noted that this functionality works correctly only
when associated and using TKIP.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The TKIP implementation was originally prepared to be a bit more
flexible in the way Michael MIC TX/RX keys are configured. However, we
are now taking care of the TX/RX MIC key swapping in user space, so
this code will not be needed. Similarly, there were some remaining WPA
testing code that won't be used in their current form. Remove the
unneeded extra complexity.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The below patch fixes a typo comamnd to command.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The beaconing vif addition is based on max beacon slot
available. So it is better to reserve a beacon slot
on interface addition and let it be configured properly
on bss_info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There's no point in disallowing scanning for a
GO interface when it's not beaconing yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Beacons from external BSSes are required for updating overlapping BSS
info (i.e. ERP protection). Pass them up unconditionally.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When operating in AP mode the wl1271 hardware filters out null-data
packets as well as management packets. This makes it impossible for
mac80211 to monitor the PS mode by using the PM bit of incoming frames.

Implement a HW flag to indicate that mac80211 should ignore the PM bit.
In addition, expose ieee80211_sta_ps_transition() to make low-level
drivers capable of controlling PS-mode.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When rate-control is performed in HW, we cannot calculate frame
duration as we do not have the skb transmission rate in SW.

ieee80211_tx_h_calculate_duration() should only be called when
ieee80211_tx_h_rate_ctrl() has been called before to initialize data
in skb->cb. This doesn't happen for drivers with HW rate-control.

Fixes the following warning when operating in AP-mode
in a driver with HW rate-control.

WARNING: at net/mac80211/tx.c:57 ieee80211_duration+0x54/0x1d8 [mac80211]()
Modules linked in: wl1271_sdio wl1271 firmware_class crc7 mac80211 cfg80211
[<c0046090>] (unwind_backtrace+0x0/0x124) from [<c0064c10>] (warn_slowpath_common+0x4c/0x64)
[<c0064c10>] (warn_slowpath_common+0x4c/0x64) from [<c0064c40>] (warn_slowpath_null+0x18/0x1c)
[<c0064c40>] (warn_slowpath_null+0x18/0x1c) from [<bf040e34>] (ieee80211_duration+0x54/0x1d8 [mac80211])
[<bf040e34>] (ieee80211_duration+0x54/0x1d8 [mac80211]) from [<bf04200c>] (invoke_tx_handlers+0xfa0/0x1088 [mac80211])
[<bf04200c>] (invoke_tx_handlers+0xfa0/0x1088 [mac80211]) from [<bf042178>] (ieee80211_tx+0x84/0x248 [mac80211])
[<bf042178>] (ieee80211_tx+0x84/0x248 [mac80211]) from [<bf042f44>] (ieee80211_tx_pending+0x12c/0x278 [mac80211])
[<bf042f44>] (ieee80211_tx_pending+0x12c/0x278 [mac80211]) from [<c0069a9c>] (tasklet_action+0x68/0xbc)
[<c0069a9c>] (tasklet_action+0x68/0xbc) from [<c006a044>] (__do_softirq+0x84/0x114)
[<c006a044>] (__do_softirq+0x84/0x114) from [<c006a1b8>] (do_softirq+0x48/0x54)
[<c006a1b8>] (do_softirq+0x48/0x54) from [<c006a4f8>] (local_bh_enable+0x98/0xcc)
[<c006a4f8>] (local_bh_enable+0x98/0xcc) from [<bf074e60>] (wl1271_rx+0x2e8/0x3a4 [wl1271])
[<bf074e60>] (wl1271_rx+0x2e8/0x3a4 [wl1271]) from [<bf071ae4>] (wl1271_irq_work+0x230/0x310 [wl1271])
[<bf071ae4>] (wl1271_irq_work+0x230/0x310 [wl1271]) from [<c0076864>] (process_one_work+0x208/0x350)
[<c0076864>] (process_one_work+0x208/0x350) from [<c0076e14>] (worker_thread+0x1cc/0x300)
[<c0076e14>] (worker_thread+0x1cc/0x300) from [<c007bb88>] (kthread+0x84/0x8c)
[<c007bb88>] (kthread+0x84/0x8c) from [<c0041494>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When a vif goes away, it could cause the super-chan
to be recalculated differently, so do that calculation
on iface removal.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The opmode recalculation is accessing hw registers.
When it is called from remove interface callback and
if there are no vifs present then hw is moved to FULL SLEEP
by radio disable. So use power save wrappers before
accessing hw registers in calculating opmode state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

move ath_update_txpow to common to remove code duplication
in both ath9k & ath9k_htc.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ani work is cancelled in dissaoctiation. But in some cases
during suspend, deauthention never be called. So we failed
to stop ani work which was identified by the following
warning.

Call Trace:
 [<ffffffffa0454a1d>] ieee80211_can_queue_work.clone.17+0x2d/0x40 [mac80211]
 [<ffffffffa0454a60>] ieee80211_queue_delayed_work+0x30/0x60 [mac80211]
 [<ffffffffa0567f82>] ath9k_ani_work+0x142/0x250 [ath9k_htc]
 [<ffffffff81073c70>] async_run_entry_fn+0x0/0x180
 [<ffffffffa0567e40>] ath9k_ani_work+0x0/0x250 [ath9k_htc]
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently cfg80211 only configures the PSM state to the driver upon creation
of a new virtual interface, but not after interface type change. The mac80211
on the other hand reinitializes its sdata structure every time the interface
type is changed, losing the PSM configuration.

Hence, if the interface type is changed to, say, ad-hoc and then back to
managed, "iw wlan0 get power_save" will claim that PSM is enabled, when in
fact on mac80211 level it is not.

Fix this in cfg80211 by configuring the PSM state to the driver each time
the interface is brought up instead of just when the interface is created.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set the rate index rate_idx and preamble flag RX_FLAG_SHORTPRE on received
packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable adhoc support in wl1251 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Implement connection quality monitoring similar to the wl1271 driver.
It triggers ieee80211_cqm_rssi_notify with the corresponding event when
RSSI drops blow RSSI threshold or rises again above the RSSI threshold.
It should be noted that wl1251 doesn't support RSSI hysteresis, instead it
uses RSSI averageing and delays events until a certain count of frames
proved RSSI change.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Port the beacon early termination feature from wl1251 driver version
included in the Maemo Fremantle kernel.
It is enabled when going to power-saving mode and disabled when leaving
power-saving mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This implements TX buffer alignment for cloned or too small skb by
copying and replacing the original skb.
Recent changes in wireless-testing seems to make this really necessary.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The queue stopping/waking functionality was broken in a way that could
cause the TX to stall if the right circumstances are met.

The problem was caused by tx_work, which is scheduled on each TX operation.
If the firmware buffer is full, tx_work does nothing. In combinition with
stopped queues or non-continues transfers, tx_work is never scheduled again.
Moreover the low watermark introduced by
9df86e2e never takes effect because of some
old code.

Solve this by scheduling tx_work every time tx_queue is non-empty and
firmware buffer is freed on tx_complete.

This also solves a possible but unlikely case: If less frames than the high
watermark are queued, but more than firmware buffer can hold. This results
in queues staying awake but the only scheduled tx_work doesn't transfer all
frames, so the remaining frames are stuck in the queue until more frames
get queued and tx_work is scheduled again.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I have a netgear WNDR3700 that appears to have an off-by-four
bug in how it fills out the hti->control_chan (I configure the
AP to channel 11, it reports 15 as control_chan).

Poke a message into the kernel logs to give users a
clue as to why they are not getting the expected
channel-type or rate.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If we cannot set the channel type, set the channel back to the
original.

Don't update the driver hardware if nothing actually changed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To support suspend/resume in if_spi we need two things:
- re-setup fw in lbs_resume(), because if_spi powercycles card;
- don't touch hwaddr on second lbs_update_hw_spec() call for same
  reason;
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use workqueue to perform SPI xfers, it's necessary to fix
nasty "BUG: scheduling while atomic", because
spu_write() calls spi_sync() and spi_sync() may sleep, but
hw_host_to_card() callback can be called from atomic context.
Remove kthread completely, workqueue now does its job.
Restore intermediate buffers which were removed in commit
86c34fe8 that introduced
mentioned bug.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

Conflicts:
	drivers/net/wireless/wl12xx/spi.c