atmtcp_remove_persistent() invokes atm_dev_lookup(), which returns a
reference of atm_dev with increased refcount or NULL if fails.

The refcount leaks issues occur in two error handling paths. If
dev_data->persist is zero or PRIV(dev)->vcc isn't NULL, the function
returns 0 without decreasing the refcount kept by a local variable,
resulting in refcount leaks.

Fix the issue by adding atm_dev_put() before returning 0 both when
dev_data->persist is zero or PRIV(dev)->vcc isn't NULL.
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in recent kernel versions there are warnings about incorrect MTU size
like these:

eth0: mtu greater than device maximum
mtk_soc_eth 1b100000.ethernet eth0: error -22 setting MTU to include DSA overhead

Fixes: bfcb8132 ("net: dsa: configure the MTU for switch ports")
Fixes: 72579e14 ("net: dsa: don't fail to probe if we couldn't set the MTU")
Fixes: 7a4c53be ("net: report invalid mtu value via netlink extack")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

If some processes in nixge_probe() fail, free_netdev(dev)
needs to be called to aviod a memory leak.

Fixes: 87ab2079 ("net: nixge: Separate ctrl and dma resources")
Fixes: abcd3d6f ("net: nixge: Fix error path for obtaining mac address")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lu Wei <luwei32@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Number of .dumpit functions try to ignore -EOPNOTSUPP errors.
Recent change missed that, and started reporting all errors
but -EMSGSIZE back from dumps. This leads to situation like
this:

$ devlink dev info
devlink answers: Operation not supported

Dump should not report an error just because the last device
to be queried could not provide an answer.

To fix this and avoid similar confusion make sure we clear
err properly, and not leave it set to an error if we don't
terminate the iteration.

Fixes: c62c2cfb ("net: devlink: don't ignore errors during dumpit")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's a race between rxrpc_sendmsg setting up a call, but then failing to
send anything on it due to an error, and recvmsg() seeing the call
completion occur and trying to return the state to the user.

An assertion fails in rxrpc_recvmsg() because the call has already been
released from the socket and is about to be released again as recvmsg deals
with it.  (The recvmsg_q queue on the socket holds a ref, so there's no
problem with use-after-free.)

We also have to be careful not to end up reporting an error twice, in such
a way that both returns indicate to userspace that the user ID supplied
with the call is no longer in use - which could cause the client to
malfunction if it recycles the user ID fast enough.

Fix this by the following means:

 (1) When sendmsg() creates a call after the point that the call has been
     successfully added to the socket, don't return any errors through
     sendmsg(), but rather complete the call and let recvmsg() retrieve
     them.  Make sendmsg() return 0 at this point.  Further calls to
     sendmsg() for that call will fail with ESHUTDOWN.

     Note that at this point, we haven't send any packets yet, so the
     server doesn't yet know about the call.

 (2) If sendmsg() returns an error when it was expected to create a new
     call, it means that the user ID wasn't used.

 (3) Mark the call disconnected before marking it completed to prevent an
     oops in rxrpc_release_call().

 (4) recvmsg() will then retrieve the error and set MSG_EOR to indicate
     that the user ID is no longer known by the kernel.

An oops like the following is produced:

	kernel BUG at net/rxrpc/recvmsg.c:605!
	...
	RIP: 0010:rxrpc_recvmsg+0x256/0x5ae
	...
	Call Trace:
	 ? __init_waitqueue_head+0x2f/0x2f
	 ____sys_recvmsg+0x8a/0x148
	 ? import_iovec+0x69/0x9c
	 ? copy_msghdr_from_user+0x5c/0x86
	 ___sys_recvmsg+0x72/0xaa
	 ? __fget_files+0x22/0x57
	 ? __fget_light+0x46/0x51
	 ? fdget+0x9/0x1b
	 do_recvmmsg+0x15e/0x232
	 ? _raw_spin_unlock+0xa/0xb
	 ? vtime_delta+0xf/0x25
	 __x64_sys_recvmmsg+0x2c/0x2f
	 do_syscall_64+0x4c/0x78
	 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 357f5ef6 ("rxrpc: Call rxrpc_release_call() on error in rxrpc_new_client_call()")
Reported-by: syzbot+b54969381df354936d96@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to replace Thor Thayer as Altera Triple Speed Ethernet
maintainer as he is moving to a different role.
Signed-off-by: Joyce Ooi <joyce.ooi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When read netdevsim trap_flow_action_cookie, we need to init it first,
or we will get "Invalid argument" error.

Fixes: d3cbb907 ("netdevsim: add ACL trap reporting cookie as a metadata")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPV6_ADDRFORM causes resource leaks when converting an IPv6 socket
to IPv4, particularly struct ipv6_ac_socklist. Similar to
struct ipv6_mc_socklist, we should just close it on this path.

This bug can be easily reproduced with the following C program:

  #include <stdio.h>
  #include <string.h>
  #include <sys/types.h>
  #include <sys/socket.h>
  #include <arpa/inet.h>

  int main()
  {
    int s, value;
    struct sockaddr_in6 addr;
    struct ipv6_mreq m6;

    s = socket(AF_INET6, SOCK_DGRAM, 0);
    addr.sin6_family = AF_INET6;
    addr.sin6_port = htons(5000);
    inet_pton(AF_INET6, "::ffff:192.168.122.194", &addr.sin6_addr);
    connect(s, (struct sockaddr *)&addr, sizeof(addr));

    inet_pton(AF_INET6, "fe80::AAAA", &m6.ipv6mr_multiaddr);
    m6.ipv6mr_interface = 5;
    setsockopt(s, SOL_IPV6, IPV6_JOIN_ANYCAST, &m6, sizeof(m6));

    value = AF_INET;
    setsockopt(s, SOL_IPV6, IPV6_ADDRFORM, &value, sizeof(value));

    close(s);
    return 0;
  }

Reported-by: ch3332xr@gmail.com
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RX queue IRQ mappings are disposed in both the TX IRQ and RX IRQ
error paths. Fix this and dispose of TX IRQ mappings correctly in
case of an error.

Fixes: ea22d51a ("ibmvnic: simplify and improve driver probe function")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw fixes

This patch set contains various fixes for mlxsw.

Patches #1-#2 fix two trap related issues introduced in previous cycle.

Patches #3-#5 fix rare use-after-frees discovered by syzkaller. After
over a week of fuzzing with the fixes, the bugs did not reproduce.

Patch #6 from Amit fixes an issue in the ethtool selftest that was
recently discovered after running the test on a new platform that
supports only 1Gbps and 10Gbps speeds.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The test case check_highest_speed_is_chosen() configures $h1 to
advertise a subset of its supported speeds and checks that $h2 chooses
the highest speed from the subset.

To find the common advertised speeds between $h1 and $h2,
common_speeds_get() is called.

Currently, the first speed returned from common_speeds_get() is removed
claiming "h1 does not advertise this speed". The claim is wrong because
the function is called after $h1 already advertised a subset of speeds.

In case $h1 supports only two speeds, it will advertise a single speed
which will be later removed because of previously mentioned bug. This
results in the test needlessly failing. When more than two speeds are
supported this is not an issue because the first advertised speed
is the lowest one.

Fix this by not removing any speed from the list of commonly advertised
speeds.

Fixes: 64916b57 ("selftests: forwarding: Add speed and auto-negotiation test")
Reported-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several notifiers are registered as part of router initialization.
Since some of these notifiers are registered before the end of the
initialization, it is possible for them to access uninitialized or freed
memory when processing notifications [1].

Additionally, some of these notifiers queue work items on a workqueue.
If these work items are executed after the router was de-initialized,
they will access freed memory.

Fix both problems by moving the registration of the notifiers to the end
of the router initialization and flush the work queue after they are
unregistered.

[1]
BUG: KASAN: use-after-free in __mutex_lock_common kernel/locking/mutex.c:938 [inline]
BUG: KASAN: use-after-free in __mutex_lock+0xeea/0x1340 kernel/locking/mutex.c:1103
Read of size 8 at addr ffff888038c3a6e0 by task kworker/u4:1/61

CPU: 1 PID: 61 Comm: kworker/u4:1 Not tainted 5.8.0-rc2+ #36
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: mlxsw_core_ordered mlxsw_sp_inet6addr_event_work
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xf6/0x16e lib/dump_stack.c:118
 print_address_description.constprop.0+0x1c/0x250 mm/kasan/report.c:383
 __kasan_report mm/kasan/report.c:513 [inline]
 kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
 __mutex_lock_common kernel/locking/mutex.c:938 [inline]
 __mutex_lock+0xeea/0x1340 kernel/locking/mutex.c:1103
 mlxsw_sp_inet6addr_event_work+0xb3/0x1b0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7123
 process_one_work+0xa3e/0x17a0 kernel/workqueue.c:2269
 worker_thread+0x9e/0x1050 kernel/workqueue.c:2415
 kthread+0x355/0x470 kernel/kthread.c:291
 ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:293

Allocated by task 1298:
 save_stack+0x1b/0x40 mm/kasan/common.c:48
 set_track mm/kasan/common.c:56 [inline]
 __kasan_kmalloc mm/kasan/common.c:494 [inline]
 __kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:467
 kmalloc include/linux/slab.h:555 [inline]
 kzalloc include/linux/slab.h:669 [inline]
 mlxsw_sp_router_init+0xb2/0x1d20 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:8074
 mlxsw_sp_init+0xbd8/0x3ac0 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2932
 __mlxsw_core_bus_device_register+0x657/0x10d0 drivers/net/ethernet/mellanox/mlxsw/core.c:1375
 mlxsw_core_bus_device_register drivers/net/ethernet/mellanox/mlxsw/core.c:1436 [inline]
 mlxsw_devlink_core_bus_device_reload_up+0xcd/0x150 drivers/net/ethernet/mellanox/mlxsw/core.c:1133
 devlink_reload net/core/devlink.c:2959 [inline]
 devlink_reload+0x281/0x3b0 net/core/devlink.c:2944
 devlink_nl_cmd_reload+0x2f1/0x7c0 net/core/devlink.c:2987
 genl_family_rcv_msg_doit net/netlink/genetlink.c:691 [inline]
 genl_family_rcv_msg net/netlink/genetlink.c:736 [inline]
 genl_rcv_msg+0x611/0x9d0 net/netlink/genetlink.c:753
 netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469
 genl_rcv+0x24/0x40 net/netlink/genetlink.c:764
 netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
 netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329
 netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918
 sock_sendmsg_nosec net/socket.c:652 [inline]
 sock_sendmsg+0x150/0x190 net/socket.c:672
 ____sys_sendmsg+0x6d8/0x840 net/socket.c:2363
 ___sys_sendmsg+0xff/0x170 net/socket.c:2417
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2450
 do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Freed by task 1348:
 save_stack+0x1b/0x40 mm/kasan/common.c:48
 set_track mm/kasan/common.c:56 [inline]
 kasan_set_free_info mm/kasan/common.c:316 [inline]
 __kasan_slab_free+0x12c/0x170 mm/kasan/common.c:455
 slab_free_hook mm/slub.c:1474 [inline]
 slab_free_freelist_hook mm/slub.c:1507 [inline]
 slab_free mm/slub.c:3072 [inline]
 kfree+0xe6/0x320 mm/slub.c:4063
 mlxsw_sp_fini+0x340/0x4e0 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3132
 mlxsw_core_bus_device_unregister+0x16c/0x6d0 drivers/net/ethernet/mellanox/mlxsw/core.c:1474
 mlxsw_devlink_core_bus_device_reload_down+0x8e/0xc0 drivers/net/ethernet/mellanox/mlxsw/core.c:1123
 devlink_reload+0xc6/0x3b0 net/core/devlink.c:2952
 devlink_nl_cmd_reload+0x2f1/0x7c0 net/core/devlink.c:2987
 genl_family_rcv_msg_doit net/netlink/genetlink.c:691 [inline]
 genl_family_rcv_msg net/netlink/genetlink.c:736 [inline]
 genl_rcv_msg+0x611/0x9d0 net/netlink/genetlink.c:753
 netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469
 genl_rcv+0x24/0x40 net/netlink/genetlink.c:764
 netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
 netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329
 netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918
 sock_sendmsg_nosec net/socket.c:652 [inline]
 sock_sendmsg+0x150/0x190 net/socket.c:672
 ____sys_sendmsg+0x6d8/0x840 net/socket.c:2363
 ___sys_sendmsg+0xff/0x170 net/socket.c:2417
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2450
 do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

The buggy address belongs to the object at ffff888038c3a000
 which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1760 bytes inside of
 2048-byte region [ffff888038c3a000, ffff888038c3a800)
The buggy address belongs to the page:
page:ffffea0000e30e00 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 head:ffffea0000e30e00 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x100000000010200(slab|head)
raw: 0100000000010200 dead000000000100 dead000000000122 ffff88806c40c000
raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff888038c3a580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff888038c3a600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff888038c3a680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                                                       ^
 ffff888038c3a700: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff888038c3a780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: 965fa8e6 ("mlxsw: spectrum_router: Make RIF deletion more robust")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The lifetime of EMAD transactions (i.e., 'struct mlxsw_reg_trans') is
managed using RCU. They are freed using kfree_rcu() once the transaction
ends.

However, in case the transaction failed it is freed immediately after being
removed from the active transactions list. This is problematic because it is
still possible for a different CPU to dereference the transaction from an RCU
read-side critical section while traversing the active transaction list in
mlxsw_emad_rx_listener_func(). In which case, a use-after-free is triggered
[1].

Fix this by freeing the transaction after a grace period by calling
kfree_rcu().

[1]
BUG: KASAN: use-after-free in mlxsw_emad_rx_listener_func+0x969/0xac0 drivers/net/ethernet/mellanox/mlxsw/core.c:671
Read of size 8 at addr ffff88800b7964e8 by task syz-executor.2/2881

CPU: 0 PID: 2881 Comm: syz-executor.2 Not tainted 5.8.0-rc4+ #44
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
 <IRQ>
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0xf6/0x16e lib/dump_stack.c:118
 print_address_description.constprop.0+0x1c/0x250 mm/kasan/report.c:383
 __kasan_report mm/kasan/report.c:513 [inline]
 kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
 mlxsw_emad_rx_listener_func+0x969/0xac0 drivers/net/ethernet/mellanox/mlxsw/core.c:671
 mlxsw_core_skb_receive+0x571/0x700 drivers/net/ethernet/mellanox/mlxsw/core.c:2061
 mlxsw_pci_cqe_rdq_handle drivers/net/ethernet/mellanox/mlxsw/pci.c:595 [inline]
 mlxsw_pci_cq_tasklet+0x12a6/0x2520 drivers/net/ethernet/mellanox/mlxsw/pci.c:651
 tasklet_action_common.isra.0+0x13f/0x3e0 kernel/softirq.c:550
 __do_softirq+0x223/0x964 kernel/softirq.c:292
 asm_call_on_stack+0x12/0x20 arch/x86/entry/entry_64.S:711
 </IRQ>
 __run_on_irqstack arch/x86/include/asm/irq_stack.h:22 [inline]
 run_on_irqstack_cond arch/x86/include/asm/irq_stack.h:48 [inline]
 do_softirq_own_stack+0x109/0x140 arch/x86/kernel/irq_64.c:77
 invoke_softirq kernel/softirq.c:387 [inline]
 __irq_exit_rcu kernel/softirq.c:417 [inline]
 irq_exit_rcu+0x16f/0x1a0 kernel/softirq.c:429
 sysvec_apic_timer_interrupt+0x4e/0xd0 arch/x86/kernel/apic/apic.c:1091
 asm_sysvec_apic_timer_interrupt+0x12/0x20 arch/x86/include/asm/idtentry.h:587
RIP: 0010:arch_local_irq_restore arch/x86/include/asm/irqflags.h:85 [inline]
RIP: 0010:__raw_spin_unlock_irqrestore include/linux/spinlock_api_smp.h:160 [inline]
RIP: 0010:_raw_spin_unlock_irqrestore+0x3b/0x40 kernel/locking/spinlock.c:191
Code: e8 2a c3 f4 fc 48 89 ef e8 12 96 f5 fc f6 c7 02 75 11 53 9d e8 d6 db 11 fd 65 ff 0d 1f 21 b3 56 5b 5d c3 e8 a7 d7 11 fd 53 9d <eb> ed 0f 1f 00 55 48 89 fd 65 ff 05 05 21 b3 56 ff 74 24 08 48 8d
RSP: 0018:ffff8880446ffd80 EFLAGS: 00000286
RAX: 0000000000000006 RBX: 0000000000000286 RCX: 0000000000000006
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffa94ecea9
RBP: ffff888012934408 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: fffffbfff57be301 R12: 1ffff110088dffc1
R13: ffff888037b817c0 R14: ffff88802442415a R15: ffff888024424000
 __do_sys_perf_event_open+0x1b5d/0x2bd0 kernel/events/core.c:11874
 do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:384
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x473dbd
Code: Bad RIP value.
RSP: 002b:00007f21e5e9cc28 EFLAGS: 00000246 ORIG_RAX: 000000000000012a
RAX: ffffffffffffffda RBX: 000000000057bf00 RCX: 0000000000473dbd
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020000040
RBP: 000000000057bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000003 R11: 0000000000000246 R12: 000000000057bf0c
R13: 00007ffd0493503f R14: 00000000004d0f46 R15: 00007f21e5e9cd80

Allocated by task 871:
 save_stack+0x1b/0x40 mm/kasan/common.c:48
 set_track mm/kasan/common.c:56 [inline]
 __kasan_kmalloc mm/kasan/common.c:494 [inline]
 __kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:467
 kmalloc include/linux/slab.h:555 [inline]
 kzalloc include/linux/slab.h:669 [inline]
 mlxsw_core_reg_access_emad+0x70/0x1410 drivers/net/ethernet/mellanox/mlxsw/core.c:1812
 mlxsw_core_reg_access+0xeb/0x540 drivers/net/ethernet/mellanox/mlxsw/core.c:1991
 mlxsw_sp_port_get_hw_xstats+0x335/0x7e0 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:1130
 update_stats_cache+0xf4/0x140 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:1173
 process_one_work+0xa3e/0x17a0 kernel/workqueue.c:2269
 worker_thread+0x9e/0x1050 kernel/workqueue.c:2415
 kthread+0x355/0x470 kernel/kthread.c:291
 ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:293

Freed by task 871:
 save_stack+0x1b/0x40 mm/kasan/common.c:48
 set_track mm/kasan/common.c:56 [inline]
 kasan_set_free_info mm/kasan/common.c:316 [inline]
 __kasan_slab_free+0x12c/0x170 mm/kasan/common.c:455
 slab_free_hook mm/slub.c:1474 [inline]
 slab_free_freelist_hook mm/slub.c:1507 [inline]
 slab_free mm/slub.c:3072 [inline]
 kfree+0xe6/0x320 mm/slub.c:4052
 mlxsw_core_reg_access_emad+0xd45/0x1410 drivers/net/ethernet/mellanox/mlxsw/core.c:1819
 mlxsw_core_reg_access+0xeb/0x540 drivers/net/ethernet/mellanox/mlxsw/core.c:1991
 mlxsw_sp_port_get_hw_xstats+0x335/0x7e0 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:1130
 update_stats_cache+0xf4/0x140 drivers/net/ethernet/mellanox/mlxsw/spectrum.c:1173
 process_one_work+0xa3e/0x17a0 kernel/workqueue.c:2269
 worker_thread+0x9e/0x1050 kernel/workqueue.c:2415
 kthread+0x355/0x470 kernel/kthread.c:291
 ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:293

The buggy address belongs to the object at ffff88800b796400
 which belongs to the cache kmalloc-512 of size 512
The buggy address is located 232 bytes inside of
 512-byte region [ffff88800b796400, ffff88800b796600)
The buggy address belongs to the page:
page:ffffea00002de500 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 head:ffffea00002de500 order:2 compound_mapcount:0 compound_pincount:0
flags: 0x100000000010200(slab|head)
raw: 0100000000010200 dead000000000100 dead000000000122 ffff88806c402500
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff88800b796380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffff88800b796400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88800b796480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
                                                          ^
 ffff88800b796500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 ffff88800b796580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb

Fixes: caf7297e ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The lifetime of the Rx listener item ('rxl_item') is managed using RCU,
but is dereferenced outside of RCU read-side critical section, which can
lead to a use-after-free.

Fix this by increasing the scope of the RCU read-side critical section.

Fixes: 93c1edb2 ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cited commit mistakenly removed the trap group for externally routed
packets (e.g., via the management interface) and grouped locally routed
and externally routed packet traps under the same group, thereby
subjecting them to the same policer.

This can result in problems, for example, when FRR is restarted and
suddenly all transient traffic is trapped to the CPU because of a
default route through the management interface. Locally routed packets
required to re-establish a BGP connection will never reach the CPU and
the routing tables will not be re-populated.

Fix this by using a different trap group for externally routed packets.

Fixes: 8110668e ("mlxsw: spectrum_trap: Register layer 3 control traps")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cited commit added the ability to program link-local prefix routes to
the ASIC so that relevant packets are routed and trapped correctly.

However, host routes were not included in the change and thus not
programmed to the ASIC. This can result in packets being trapped via an
external route trap instead of a local route trap as in IPv4.

Fix this by programming all the link-local routes to the ASIC.

Fixes: 10d3757f ("mlxsw: spectrum_router: Allow programming link-local prefix routes")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib_trie_unmerge() is called with RTNL held, but not from an RCU
read-side critical section. This leads to the following warning [1] when
the FIB alias list in a leaf is traversed with
hlist_for_each_entry_rcu().

Since the function is always called with RTNL held and since
modification of the list is protected by RTNL, simply use
hlist_for_each_entry() and silence the warning.

[1]
WARNING: suspicious RCU usage
5.8.0-rc4-custom-01520-gc1f937f3f83b #30 Not tainted
-----------------------------
net/ipv4/fib_trie.c:1867 RCU-list traversed in non-reader section!!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/164:
 #0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x49a/0xbd0

stack backtrace:
CPU: 0 PID: 164 Comm: ip Not tainted 5.8.0-rc4-custom-01520-gc1f937f3f83b #30
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
 dump_stack+0x100/0x184
 lockdep_rcu_suspicious+0x153/0x15d
 fib_trie_unmerge+0x608/0xdb0
 fib_unmerge+0x44/0x360
 fib4_rule_configure+0xc8/0xad0
 fib_nl_newrule+0x37a/0x1dd0
 rtnetlink_rcv_msg+0x4f7/0xbd0
 netlink_rcv_skb+0x17a/0x480
 rtnetlink_rcv+0x22/0x30
 netlink_unicast+0x5ae/0x890
 netlink_sendmsg+0x98a/0xf40
 ____sys_sendmsg+0x879/0xa00
 ___sys_sendmsg+0x122/0x190
 __sys_sendmsg+0x103/0x1d0
 __x64_sys_sendmsg+0x7d/0xb0
 do_syscall_64+0x54/0xa0
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fc80a234e97
Code: Bad RIP value.
RSP: 002b:00007ffef8b66798 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fc80a234e97
RDX: 0000000000000000 RSI: 00007ffef8b66800 RDI: 0000000000000003
RBP: 000000005f141b1c R08: 0000000000000001 R09: 0000000000000000
R10: 00007fc80a2a8ac0 R11: 0000000000000246 R12: 0000000000000001
R13: 0000000000000000 R14: 00007ffef8b67008 R15: 0000556fccb10020

Fixes: 0ddcf43d ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit cited below removed the RCU read-side critical section from
rtnl_fdb_dump() which means that the ndo_fdb_dump() callback is invoked
without RCU protection.

This results in the following warning [1] in the VXLAN driver, which
relied on the callback being invoked from an RCU read-side critical
section.

Fix this by calling rcu_read_lock() in the VXLAN driver, as already done
in the bridge driver.

[1]
WARNING: suspicious RCU usage
5.8.0-rc4-custom-01521-g481007553ce6 #29 Not tainted
-----------------------------
drivers/net/vxlan.c:1379 RCU-list traversed in non-reader section!!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
1 lock held by bridge/166:
 #0: ffffffff85a27850 (rtnl_mutex){+.+.}-{3:3}, at: netlink_dump+0xea/0x1090

stack backtrace:
CPU: 1 PID: 166 Comm: bridge Not tainted 5.8.0-rc4-custom-01521-g481007553ce6 #29
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
 dump_stack+0x100/0x184
 lockdep_rcu_suspicious+0x153/0x15d
 vxlan_fdb_dump+0x51e/0x6d0
 rtnl_fdb_dump+0x4dc/0xad0
 netlink_dump+0x540/0x1090
 __netlink_dump_start+0x695/0x950
 rtnetlink_rcv_msg+0x802/0xbd0
 netlink_rcv_skb+0x17a/0x480
 rtnetlink_rcv+0x22/0x30
 netlink_unicast+0x5ae/0x890
 netlink_sendmsg+0x98a/0xf40
 __sys_sendto+0x279/0x3b0
 __x64_sys_sendto+0xe6/0x1a0
 do_syscall_64+0x54/0xa0
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fe14fa2ade0
Code: Bad RIP value.
RSP: 002b:00007fff75bb5b88 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00005614b1ba0020 RCX: 00007fe14fa2ade0
RDX: 000000000000011c RSI: 00007fff75bb5b90 RDI: 0000000000000003
RBP: 00007fff75bb5b90 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00005614b1b89160
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000

Fixes: 5e6d2435 ("bridge: netlink dump interface at par with brctl")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed redundant words.

Fixes: 571912c6 ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In multiproto mode, bareudp_xmit() accepts sending multicast MPLS and
IPv6 packets regardless of the bareudp ethertype. In practice, this
let an IP tunnel send multicast MPLS packets, or an MPLS tunnel send
IPv6 packets.

We need to restrict the test further, so that the multiproto mode only
enables
  * IPv6 for IPv4 tunnels,
  * or multicast MPLS for unicast MPLS tunnels.

To improve clarity, the protocol validation is moved to its own
function, where each logical test has its own condition.

v2: s/ntohs/htons/

Fixes: 4b5f6723 ("net: Special handling for IP & MPLS.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_route_info_create() invokes nexthop_get(), which increases the
refcount of the "nh".

When ip6_route_info_create() returns, local variable "nh" becomes
invalid, so the refcount should be decreased to keep refcount balanced.

The reference counting issue happens in one exception handling path of
ip6_route_info_create(). When nexthops can not be used with source
routing, the function forgets to decrease the refcnt increased by
nexthop_get(), causing a refcnt leak.

Fix this issue by pulling up the error source routing handling when
nexthops can not be used with source routing.

Fixes: f88d8ea6 ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subbaraya Sundeep says:

====================
Fix bugs in Octeontx2 netdev driver

There are problems in the existing Octeontx2
netdev drivers like missing cancel_work for the
reset task, missing lock in reset task and
missing unergister_netdev in driver remove.
This patch set fixes the above problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added unregister_netdev in the driver remove
function. Generally unregister_netdev is called
after disabling all the device interrupts but here
it is called before disabling device mailbox
interrupts. The reason behind this is VF needs
mailbox interrupt to communicate with its PF to
clean up its resources during otx2_stop.
otx2_stop disables packet I/O and queue interrupts
first and by using mailbox interrupt communicates
to PF to free VF resources. Hence this patch
calls unregister_device just before
disabling mailbox interrupts.

Fixes: 3184fb5b ("octeontx2-vf: Virtual function driver support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During driver exit cancel the queued
reset_task work in VF driver.

Fixes: 3184fb5b ("octeontx2-vf: Virtual function driver support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two bugs exist in the code related to reset_task
in PF driver one is the missing protection
against network stack ndo_open and ndo_close.
Other one is the missing cancel_work.
This patch fixes those problems.

Fixes: 4ff7d148 ("octeontx2-pf: Error handling support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It appears that not disabling a PCI device on .shutdown may lead to
a Hardware Error with particular (perhaps buggy) BIOS versions:

    mlx4_en: eth0: Close port called
    mlx4_en 0000:04:00.0: removed PHC
    reboot: Restarting system
    {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 1
    {1}[Hardware Error]: event severity: fatal
    {1}[Hardware Error]:  Error 0, type: fatal
    {1}[Hardware Error]:   section_type: PCIe error
    {1}[Hardware Error]:   port_type: 4, root port
    {1}[Hardware Error]:   version: 1.16
    {1}[Hardware Error]:   command: 0x4010, status: 0x0143
    {1}[Hardware Error]:   device_id: 0000:00:02.2
    {1}[Hardware Error]:   slot: 0
    {1}[Hardware Error]:   secondary_bus: 0x04
    {1}[Hardware Error]:   vendor_id: 0x8086, device_id: 0x2f06
    {1}[Hardware Error]:   class_code: 000604
    {1}[Hardware Error]:   bridge: secondary_status: 0x2000, control: 0x0003
    {1}[Hardware Error]:   aer_uncor_status: 0x00100000, aer_uncor_mask: 0x00000000
    {1}[Hardware Error]:   aer_uncor_severity: 0x00062030
    {1}[Hardware Error]:   TLP Header: 40000018 040000ff 791f4080 00000000
[hw error repeats]
    Kernel panic - not syncing: Fatal hardware error!
    CPU: 0 PID: 2189 Comm: reboot Kdump: loaded Not tainted 5.6.x-blabla #1
    Hardware name: HP ProLiant DL380 Gen9/ProLiant DL380 Gen9, BIOS P89 05/05/2017

Fix the mlx4 driver.

This is a very similar problem to what had been fixed in:
commit 0d98ba8d ("scsi: hpsa: disable device during shutdown")
to address https://bugzilla.kernel.org/show_bug.cgi?id=199779.

Fixes: 2ba5fbd6 ("net/mlx4_core: Handle AER flow properly")
Reported-by: Jake Lawrence <lawja@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Herbert Xu says:

====================
rhashtable: Fix unprotected RCU dereference in __rht_ptr

This patch series fixes an unprotected dereference in __rht_ptr.
The first patch is a minimal fix that does not use the correct
RCU markings but is suitable for backport, and the second patch
cleans up the RCU markings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch restores the RCU marking on bucket_table->buckets as
it really does need RCU protection.  Its removal had led to a fatal
bug.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rcu_dereference call in rht_ptr_rcu is completely bogus because
we've already dereferenced the value in __rht_ptr and operated on it.
This causes potential double readings which could be fatal.  The RCU
dereference must occur prior to the comparison in __rht_ptr.

This patch changes the order of RCU dereference so that it is done
first and the result is then fed to __rht_ptr.  The RCU marking
changes have been minimised using casts which will be removed in
a follow-up patch.

Fixes: ba6306e3 ("rhashtable: Remove RCU marking from...")
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify mtk_gmac0_rgmii_adjust() so it can always be called.
mtk_gmac0_rgmii_adjust() sets-up the TRGMII clocks.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-By: David Woodhouse <dwmw2@infradead.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 fixes-2020-07-28

This series introduces some fixes to mlx5 driver.
v1->v2:
 - Drop the "Hold reference on mirred devices" patch, until Or's
   comments are addressed.
 - Imporve "Modify uplink state" patch commit message per Or's request.

Please pull and let me know if there is any problem.

For -Stable:

For -stable v4.9
 ('net/mlx5e: Fix error path of device attach')

For -stable v4.15
 ('net/mlx5: Verify Hardware supports requested ptp function on a given
pin')

For -stable v5.3
 ('net/mlx5e: Modify uplink state on interface up/down')

For -stable v5.4
 ('net/mlx5e: Fix kernel crash when setting vf VLANID on a VF dev')
 ('net/mlx5: E-switch, Destroy TSAR when fail to enable the mode')

For -stable v5.5
 ('net/mlx5: E-switch, Destroy TSAR after reload interface')

For -stable v5.7
 ('net/mlx5: Fix a bug of using ptp channel index as pin index')
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hovold says:

====================
net: lan78xx: fix NULL deref and memory leak

The first two patches fix a NULL-pointer dereference at probe that can
be triggered by a malicious device and a small transfer-buffer memory
leak, respectively.

For another subsystem I would have marked them:

	Cc: stable@vger.kernel.org	# 4.3

The third one replaces the driver's current broken endpoint lookup
helper, which could end up accepting incomplete interfaces and whose
results weren't even useeren
Johan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Drop the bogus endpoint-lookup helper which could end up accepting
interfaces based on endpoints belonging to unrelated altsettings.

Note that the returned bulk pipes and interrupt endpoint descriptor
were never actually used. Instead the bulk-endpoint numbers are
hardcoded to 1 and 2 (matching the specification), while the interrupt-
endpoint descriptor was assumed to be the third descriptor created by
USB core.

Try to bring some order to this by dropping the bogus lookup helper and
adding the missing endpoint sanity checks while keeping the interrupt-
descriptor assumption for now.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The interrupt URB transfer-buffer was never freed on disconnect or after
probe errors.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing endpoint sanity check to prevent a NULL-pointer
dereference should a malicious device lack the expected endpoints.

Note that the driver has a broken endpoint-lookup helper,
lan78xx_get_endpoints(), which can end up accepting interfaces in an
altsetting without endpoints as long as *some* altsetting has a bulk-in
and a bulk-out endpoint.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

in case of an error tty_register_device_attr() returns ERR_PTR(),
add IS_ERR() check

Reported-and-tested-by: syzbot+67b2bd0e34f952d0321e@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=67b2bd0e34f952d0321eSigned-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the cited commit, function 'mlx5_eswitch_set_vport_vlan' started
to acquire esw->state_lock.
However, esw is not defined for VF devices, hence attempting to set vf
VLANID on a VF dev will cause a kernel panic.

Fix it by moving up the (redundant) esw validation from function
'__mlx5_eswitch_set_vport_vlan' since the rest of the callers now have
and use a valid esw.

For example with vf device eth4:
 # ip link set dev eth4 vf 0 vlan 0

Trace of the panic:
 [  411.409842] BUG: unable to handle page fault for address: 00000000000011b8
 [  411.449745] #PF: supervisor read access in kernel mode
 [  411.452348] #PF: error_code(0x0000) - not-present page
 [  411.454938] PGD 80000004189c9067 P4D 80000004189c9067 PUD 41899a067 PMD 0
 [  411.458382] Oops: 0000 [#1] SMP PTI
 [  411.460268] CPU: 4 PID: 5711 Comm: ip Not tainted 5.8.0-rc4_for_upstream_min_debug_2020_07_08_22_04 #1
 [  411.462447] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
 [  411.464158] RIP: 0010:__mutex_lock+0x4e/0x940
 [  411.464928] Code: fd 41 54 49 89 f4 41 52 53 89 d3 48 83 ec 70 44 8b 1d ee 03 b0 01 65 48 8b 04 25 28 00 00 00 48 89 45 c8 31 c0 45 85 db 75 0a <48> 3b 7f 60 0f 85 7e 05 00 00 49 8d 45 68 41 56 41 b8 01 00 00 00
 [  411.467678] RSP: 0018:ffff88841fcd74b0 EFLAGS: 00010246
 [  411.468562] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
 [  411.469715] RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000001158
 [  411.470812] RBP: ffff88841fcd7550 R08: ffffffffa00fa1ce R09: 0000000000000000
 [  411.471835] R10: ffff88841fcd7570 R11: 0000000000000000 R12: 0000000000000002
 [  411.472862] R13: 0000000000001158 R14: ffffffffa00fa1ce R15: 0000000000000000
 [  411.474004] FS:  00007faee7ca6b80(0000) GS:ffff88846fc00000(0000) knlGS:0000000000000000
 [  411.475237] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 [  411.476129] CR2: 00000000000011b8 CR3: 000000041909c006 CR4: 0000000000360ea0
 [  411.477260] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 [  411.478340] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 [  411.479332] Call Trace:
 [  411.479760]  ? __nla_validate_parse.part.6+0x57/0x8f0
 [  411.482825]  ? mlx5_eswitch_set_vport_vlan+0x3e/0xa0 [mlx5_core]
 [  411.483804]  mlx5_eswitch_set_vport_vlan+0x3e/0xa0 [mlx5_core]
 [  411.484733]  mlx5e_set_vf_vlan+0x41/0x50 [mlx5_core]
 [  411.485545]  do_setlink+0x613/0x1000
 [  411.486165]  __rtnl_newlink+0x53d/0x8c0
 [  411.486791]  ? mark_held_locks+0x49/0x70
 [  411.487429]  ? __lock_acquire+0x8fe/0x1eb0
 [  411.488085]  ? rcu_read_lock_sched_held+0x52/0x60
 [  411.488998]  ? kmem_cache_alloc_trace+0x16d/0x2d0
 [  411.489759]  rtnl_newlink+0x47/0x70
 [  411.490357]  rtnetlink_rcv_msg+0x24e/0x450
 [  411.490978]  ? netlink_deliver_tap+0x92/0x3d0
 [  411.491631]  ? validate_linkmsg+0x330/0x330
 [  411.492262]  netlink_rcv_skb+0x47/0x110
 [  411.492852]  netlink_unicast+0x1ac/0x270
 [  411.493551]  netlink_sendmsg+0x336/0x450
 [  411.494209]  sock_sendmsg+0x30/0x40
 [  411.494779]  ____sys_sendmsg+0x1dd/0x1f0
 [  411.495378]  ? copy_msghdr_from_user+0x5c/0x90
 [  411.496082]  ___sys_sendmsg+0x87/0xd0
 [  411.496683]  ? lock_acquire+0xb9/0x3a0
 [  411.497322]  ? lru_cache_add+0x5/0x170
 [  411.497944]  ? find_held_lock+0x2d/0x90
 [  411.498568]  ? handle_mm_fault+0xe46/0x18c0
 [  411.499205]  ? __sys_sendmsg+0x51/0x90
 [  411.499784]  __sys_sendmsg+0x51/0x90
 [  411.500341]  do_syscall_64+0x59/0x2e0
 [  411.500938]  ? asm_exc_page_fault+0x8/0x30
 [  411.501609]  ? rcu_read_lock_sched_held+0x52/0x60
 [  411.502350]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
 [  411.503093] RIP: 0033:0x7faee73b85a7
 [  411.503654] Code: Bad RIP value.

Fixes: 0e18134f ("net/mlx5e: Eswitch, use state_lock to synchronize vlan change")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When setting the PF interface up/down, notify the firmware to update
uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled.

This behavior will prevent sending traffic out on uplink port when PF is
down, such as sending traffic from a VF interface which is still up.
Currently when calling mlx5e_open/close(), the driver only sends PAOS
command to notify the firmware to set the physical port state to
up/down, however, it is not sufficient. When VF is in "auto" state, it
follows the uplink state, which was not updated on mlx5e_open/close()
before this patch.

When switchdev mode is enabled and uplink representor is first enabled,
set the uplink port state value back to its FW default "AUTO".

Fixes: 63bfd399 ("net/mlx5e: Send PAOS command on interface up/down")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In a special configuration, a ConnectX6-Dx pin pps-out might be activated
when driver is loaded. Fix the driver to always read the operational pin
mode when registering it, and advertise it accordingly.

Fixes: ee7f1220 ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

mlx5e_rep_is_lag_netdev is used as first check as part of netdev events
handler for bond device of non-uplink representors, this handler can get
any netdevice under the same network namespace of mlx5e netdevice. Current
code treats the netdev as mlx5e netdev and only later on verifies this,
hence causes the following Kasan trace:
[15402.744990] ==================================================================
[15402.746942] BUG: KASAN: slab-out-of-bounds in mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.749009] Read of size 8 at addr ffff880391f3f6b0 by task ovs-vswitchd/5347

[15402.752065] CPU: 7 PID: 5347 Comm: ovs-vswitchd Kdump: loaded Tainted: G    B      O     --------- -t - 4.18.0-g3dcc204d291d-dirty #1
[15402.755349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[15402.757600] Call Trace:
[15402.758968]  dump_stack+0x71/0xab
[15402.760427]  print_address_description+0x6a/0x270
[15402.761969]  kasan_report+0x179/0x2d0
[15402.763445]  ? mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.765121]  mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.766782]  mlx5e_rep_esw_bond_netevent+0x129/0x620 [mlx5_core]

Fix by deferring the violating access to be post the netdev verify check.

Fixes: 7e51891a ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>