1. 18 May, 2013 5 commits
  2. 17 May, 2013 8 commits
  3. 16 May, 2013 8 commits
  4. 13 May, 2013 14 commits
    • Linus Torvalds's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · dbbffe68
      Linus Torvalds authored
      Pull networking fixes from David Miller:
       "Several small bug fixes all over:
      
         1) be2net driver uses wrong payload length when submitting MAC list
            get requests to the chip.  From Sathya Perla.
      
         2) Fix mwifiex memory leak on driver unload, from Amitkumar Karwar.
      
         3) Prevent random memory access in batman-adv, from Marek Lindner.
      
         4) batman-adv doesn't check for pskb_trim_rcsum() errors, also from
            Marek Lindner.
      
         5) Fix fec crashes on rapid link up/down, from Frank Li.
      
         6) Fix inner protocol grovelling in GSO, from Pravin B Shelar.
      
         7) Link event validation fix in qlcnic from Rajesh Borundia.
      
         8) Not all FEC chips can support checksum offload, fix from Shawn
            Guo.
      
         9) EXPORT_SYMBOL + inline doesn't make any sense, from Denis Efremov.
      
        10) Fix race in passthru mode during device removal in macvlan, from
            Jiri Pirko.
      
        11) Fix RCU hash table lookup socket state race in ipv6, leading to
            NULL pointer derefs, from Eric Dumazet.
      
        12) Add several missing HAS_DMA kconfig dependencies, from Geert
            Uyttterhoeven.
      
        13) Fix bogus PCI resource management in 3c59x driver, from Sergei
            Shtylyov.
      
        14) Fix info leak in ipv6 GRE tunnel driver, from Amerigo Wang.
      
        15) Fix device leak in ipv6 IPSEC policy layer, from Cong Wang.
      
        16) DMA mapping leak fix in qlge from Thadeu Lima de Souza Cascardo.
      
        17) Missing iounmap on probe failure in bna driver, from Wei Yongjun."
      
      * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
        bna: add missing iounmap() on error in bnad_init()
        qlge: fix dma map leak when the last chunk is not allocated
        xfrm6: release dev before returning error
        ipv6,gre: do not leak info to user-space
        virtio_net: use default napi weight by default
        emac: Fix EMAC soft reset on 460EX/GT
        3c59x: fix PCI resource management
        caif: CAIF_VIRTIO should depend on HAS_DMA
        net/ethernet: MACB should depend on HAS_DMA
        net/ethernet: ARM_AT91_ETHER should depend on HAS_DMA
        net/wireless: ATH9K should depend on HAS_DMA
        net/ethernet: STMMAC_ETH should depend on HAS_DMA
        net/ethernet: NET_CALXEDA_XGMAC should depend on HAS_DMA
        ipv6: do not clear pinet6 field
        macvlan: fix passthru mode race between dev removal and rx path
        ipv4: ip_output: remove inline marking of EXPORT_SYMBOL functions
        net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode
        net/mlx4_core: Add missing report on VST and spoof-checking dev caps
        net: fec: enable hardware checksum only on imx6q-fec
        qlcnic: Fix validation of link event command.
        ...
      dbbffe68
    • Wei Yongjun's avatar
      bna: add missing iounmap() on error in bnad_init() · ba21fc69
      Wei Yongjun authored
      Add the missing iounmap() before return from bnad_init()
      in the error handling case.
      Introduced by commit 01b54b14
      (bna: tx rx cleanup fix).
      Signed-off-by: default avatarWei Yongjun <yongjun_wei@trendmicro.com.cn>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ba21fc69
    • Thadeu Lima de Souza Cascardo's avatar
      qlge: fix dma map leak when the last chunk is not allocated · ef380794
      Thadeu Lima de Souza Cascardo authored
      qlge allocates chunks from a page that it maps and unmaps that page when
      the last chunk is released. When the driver is unloaded or the card is
      removed, all chunks are released and the page is unmapped for the last
      chunk.
      
      However, when the last chunk of a page is not allocated and the device
      is removed, that page is not unmapped. In fact, its last reference is
      not put and there's also a page leak. This bug prevents a device from
      being properly hotplugged.
      
      When the DMA API debug option is enabled, the following messages show
      the pending DMA allocation after we remove the driver.
      
      This patch fixes the bug by unmapping and putting the page from the ring
      if its last chunk has not been allocated.
      
      pci 0005:98:00.0: DMA-API: device driver has pending DMA allocations while released from device [count=1]
      One of leaked entries details: [device address=0x0000000060a80000] [size=65536 bytes] [mapped with DMA_FROM_DEVICE] [mapped as page]
      ------------[ cut here ]------------
      WARNING: at lib/dma-debug.c:746
      Modules linked in: qlge(-) rpadlpar_io rpaphp pci_hotplug fuse [last unloaded: qlge]
      NIP: c0000000003fc3ec LR: c0000000003fc3e8 CTR: c00000000054de60
      REGS: c0000003ee9c74e0 TRAP: 0700   Tainted: G           O  (3.7.2)
      MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI>  CR: 28002424  XER: 00000001
      SOFTE: 1
      CFAR: c0000000007a39c8
      TASK = c0000003ee8d5c90[8406] 'rmmod' THREAD: c0000003ee9c4000 CPU: 31
      GPR00: c0000000003fc3e8 c0000003ee9c7760 c000000000c789f8 00000000000000ee
      GPR04: 0000000000000000 00000000000000ef 0000000000004000 0000000000010000
      GPR08: 00000000000000be c000000000b22088 c000000000c4c218 00000000007c0000
      GPR12: 0000000028002422 c00000000ff26c80 0000000000000000 000001001b0f1b40
      GPR16: 00000000100cb9d8 0000000010093088 c000000000cdf910 0000000000000001
      GPR20: 0000000000000000 c000000000dbfc00 0000000000000000 c000000000dbfb80
      GPR24: c0000003fafc9d80 0000000000000001 000000000001ff80 c0000003f38f7888
      GPR28: c000000000ddfc00 0000000000000400 c000000000bd7790 c000000000ddfb80
      NIP [c0000000003fc3ec] .dma_debug_device_change+0x22c/0x2b0
      LR [c0000000003fc3e8] .dma_debug_device_change+0x228/0x2b0
      Call Trace:
      [c0000003ee9c7760] [c0000000003fc3e8] .dma_debug_device_change+0x228/0x2b0 (unreliable)
      [c0000003ee9c7840] [c00000000079a098] .notifier_call_chain+0x78/0xf0
      [c0000003ee9c78e0] [c0000000000acc20] .__blocking_notifier_call_chain+0x70/0xb0
      [c0000003ee9c7990] [c0000000004a9580] .__device_release_driver+0x100/0x140
      [c0000003ee9c7a20] [c0000000004a9708] .driver_detach+0x148/0x150
      [c0000003ee9c7ac0] [c0000000004a8144] .bus_remove_driver+0xc4/0x150
      [c0000003ee9c7b60] [c0000000004aa58c] .driver_unregister+0x8c/0xe0
      [c0000003ee9c7bf0] [c0000000004090b4] .pci_unregister_driver+0x34/0xf0
      [c0000003ee9c7ca0] [d000000002231194] .qlge_exit+0x1c/0x34 [qlge]
      [c0000003ee9c7d20] [c0000000000e36d8] .SyS_delete_module+0x1e8/0x290
      [c0000003ee9c7e30] [c0000000000098d4] syscall_exit+0x0/0x94
      Instruction dump:
      7f26cb78 e818003a e87e81a0 e8f80028 e9180030 796b1f24 78001f24 7d6a5a14
      7d2a002a e94b0020 483a7595 60000000 <0fe00000> 2fb80000 40de0048 80120050
      ---[ end trace 4294f9abdb01031d ]---
      Mapped at:
       [<d000000002222f54>] .ql_update_lbq+0x384/0x580 [qlge]
       [<d000000002227bd0>] .ql_clean_inbound_rx_ring+0x300/0xc60 [qlge]
       [<d0000000022288cc>] .ql_napi_poll_msix+0x39c/0x5a0 [qlge]
       [<c0000000006b3c50>] .net_rx_action+0x170/0x300
       [<c000000000081840>] .__do_softirq+0x170/0x300
      Signed-off-by: default avatarThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
      Acked-by: default avatarJitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ef380794
    • Linus Torvalds's avatar
      Merge tag 'spi-v3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi · 1f638766
      Linus Torvalds authored
      Pull spi updates from Mark Brown:
       "A few driver specific fixes plus improved error handling in the
        generic DT GPIO chipselect handling - not exciting but useful."
      
      * tag 'spi-v3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
        spi/spi-atmel: BUG: fix doesn' support 16 bits transfers using PIO
        spi/davinci: fix module build error
        spi: Return error from of_spi_register_master on bad "cs-gpios" property
        spi: Initialize cs_gpio and cs_gpios with -ENOENT
        spi/atmel: fix speed_hz check in atmel_spi_transfer()
      1f638766
    • Linus Torvalds's avatar
      Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linux · fea0f9ff
      Linus Torvalds authored
      Pull drm fixes from Dave Airlie:
       "Just a few straggling fixes I hoovered up, and an intel fixes pull
        from Daniel which fixes some regressions, and some mgag200 fixes from
        Matrox."
      
      * 'drm-next' of git://people.freedesktop.org/~airlied/linux:
        drm/mgag200: Fix framebuffer base address programming
        drm/mgag200: Convert counter delays to jiffies
        drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
        drm/mgag200: Don't change unrelated registers during modeset
        drm: Only print a debug message when the polled connector has changed
        drm: Make the HPD status updates debug logs more readable
        drm: Use names of ioctls in debug traces
        drm: Remove pointless '-' characters from drm_fb_helper documentation
        drm: Add kernel-doc for drm_fb_helper_funcs->initial_config
        drm: refactor call to request_module
        drm: Don't prune modes loudly when a connector is disconnected
        drm: Add missing break in the command line mode parsing code
        drm/i915: clear the stolen fb before resuming
        Revert "drm/i915: Calculate correct stolen size for GEN7+"
        drm/i915: hsw: fix link training for eDP on port-A
        Revert "drm/i915: revert eDP bpp clamping code changes"
        drm: don't check modeset locks in panic handler
        drm/i915: Fix pipe enabled mask for pipe C in WM calculations
        drm/mm: fix dump table BUG
        drm/i915: Always normalize return timeout for wait_timeout_ioctl
      fea0f9ff
    • Linus Torvalds's avatar
      Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux · aef2ea91
      Linus Torvalds authored
      Pull virtio/lguest fixes from Rusty Russell:
       "Missing license tag and some fallout from the lguest pagetable rework"
      
      * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
        lguest: clear cached last cpu when guest_set_pgd() called.
        Add missing module license tag to vring helpers.
      aef2ea91
    • Mark Brown's avatar
      88b0357d
    • Mark Brown's avatar
      0faa3146
    • Christopher Harvey's avatar
      drm/mgag200: Fix framebuffer base address programming · 9f1d0366
      Christopher Harvey authored
      Higher bits of the base address of framebuffers weren't being
      programmed properly. This caused framebuffers that didn't happen to be
      allocated at a low enough address to not be displayed properly.
      Signed-off-by: default avatarChristopher Harvey <charvey@matrox.com>
      Signed-off-by: default avatarMathieu Larouche <mathieu.larouche@matrox.com>
      Acked-by: default avatarJulia Lemire <jlemire@matrox.com>
      Tested-by: default avatarJulia Lemire <jlemire@matrox.com>
      Cc: stable@vger.kernel.org
      Signed-off-by: default avatarDave Airlie <airlied@redhat.com>
      9f1d0366
    • Christopher Harvey's avatar
    • Christopher Harvey's avatar
      drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register · fb70a669
      Christopher Harvey authored
      The original line,
        WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp);
      wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where
      MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into
      MGA1064_PIX_CLK_CTL. Change the line to write properly into
      MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use
      the same pattern (but work correctly), so this patch updates them all
      to use this new (slightly more efficient) write pattern. The WREG_DAC
      macro was causing the DAC_INDEX register to be set to the same value
      twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX
      is already at the value we want.
      Signed-off-by: default avatarChristopher Harvey <charvey@matrox.com>
      Acked-by: default avatarJulia Lemire <jlemire@matrox.com>
      Tested-by: default avatarJulia Lemire <jlemire@matrox.com>
      Acked-by: default avatarMathieu Larouche <mathieu.larouche@matrox.com>
      Cc: stable@vger.kernel.org
      Signed-off-by: default avatarDave Airlie <airlied@redhat.com>
      fb70a669
    • Christopher Harvey's avatar
      drm/mgag200: Don't change unrelated registers during modeset · 9d8aa55f
      Christopher Harvey authored
      Registers in indices below 0x18 are totally unrelated to modesetting,
      so don't write 0's, or anything else into them on modeset. Most of
      these registers are hardware cursor related, so this existing code
      interferes with hardware cursor development.
      Signed-off-by: default avatarChristopher Harvey <charvey@matrox.com>
      Tested-by: default avatarJulia Lemire <jlemire@matrox.com>
      Acked-by: default avatarJulia Lemire <jlemire@matrox.com>
      Acked-by: default avatarMathieu Larouche <mathieu.larouche@matrox.com>
      Signed-off-by: default avatarDave Airlie <airlied@redhat.com>
      9d8aa55f
    • Lespiau, Damien's avatar
    • Lespiau, Damien's avatar
      drm: Make the HPD status updates debug logs more readable · ed7951dc
      Lespiau, Damien authored
      Instead of just printing "status updated from 1 to 2", make those enum
      numbers immediately readable.
      
      v2: Also patch output_poll_execute() (Daniel Vetter)
      v3: Use drm_get_connector_status_name (Ville Syrjälä)
      Signed-off-by: default avatarDamien Lespiau <damien.lespiau@intel.com>
      Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (for v1)
      Signed-off-by: default avatarDave Airlie <airlied@redhat.com>
      ed7951dc
  5. 12 May, 2013 5 commits
    • Cong Wang's avatar
      xfrm6: release dev before returning error · 84c4a9df
      Cong Wang authored
      We forget to call dev_put() on error path in xfrm6_fill_dst(),
      its caller doesn't handle this.
      
      Cc: Herbert Xu <herbert@gondor.apana.org.au>
      Cc: Steffen Klassert <steffen.klassert@secunet.com>
      Cc: David S. Miller <davem@davemloft.net>
      Signed-off-by: default avatarCong Wang <amwang@redhat.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      84c4a9df
    • Amerigo Wang's avatar
      ipv6,gre: do not leak info to user-space · 5dbd5068
      Amerigo Wang authored
      There is a hole in struct ip6_tnl_parm2, so we have to
      zero the struct on stack before copying it to user-space.
      
      Cc: David S. Miller <davem@davemloft.net>
      Signed-off-by: default avatarCong Wang <amwang@redhat.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      5dbd5068
    • Amerigo Wang's avatar
      virtio_net: use default napi weight by default · d34710e3
      Amerigo Wang authored
      Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
      we warn drivers when they use napi weight higher than NAPI_POLL_WEIGHT,
      but virtio_net still uses 128 by default. This patch makes its default
      value to NAPI_POLL_WEIGHT.
      
      Cc: "Michael S. Tsirkin" <mst@redhat.com>
      Cc: Eric Dumazet <eric.dumazet@gmail.com>
      Cc: David S. Miller <davem@davemloft.net>
      Signed-off-by: default avatarCong Wang <amwang@redhat.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d34710e3
    • Petri Gynther's avatar
      emac: Fix EMAC soft reset on 460EX/GT · 23fbb5a8
      Petri Gynther authored
      Fix EMAC soft reset on 460EX/GT to select the right PHY clock source
      before and after the soft reset.
      
      EMAC with PHY should use the clock from PHY during soft reset.
      EMAC without PHY should use the internal clock during soft reset.
      
      PPC460EX/GT Embedded Processor Advanced User's Manual
      section 28.10.1 Mode Register 0 (EMACx_MR0) states:
      Note: The PHY must provide a TX Clk in order to perform a soft reset
      of the EMAC. If none is present, select the internal clock
      (SDR0_ETH_CFG[EMACx_PHY_CLK] = 1).
      After a soft reset, select the external clock.
      
      Without the fix, 460EX/GT-based boards with RGMII PHYs attached to
      EMACs experience EMAC interrupt storm and system watchdog reset when
      issuing "ifconfig eth0 down" + "ifconfig eth0 up" a few times.
      The system enters endless loop of serving emac_irq() with EMACx_ISR
      register stuck at value 0x10000000 (Rx parity error).
      
      With the fix, the above issue is no longer observed.
      Signed-off-by: default avatarPetri Gynther <pgynther@google.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      23fbb5a8
    • Sergei Shtylyov's avatar
      3c59x: fix PCI resource management · 4b264a16
      Sergei Shtylyov authored
      The driver wrongly claimed I/O ports at an address returned by pci_iomap() --
      even if it was passed an MMIO address.  Fix this by claiming/releasing all PCI
      resources in the PCI driver's probe()/remove() methods instead and get rid of
      'must_free_region' flag weirdness (why would Cardbus claim anything for us?).
      Signed-off-by: default avatarSergei Shtylyov <sshtylyov@ru.mvista.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      4b264a16