- 08 Jun, 2011 3 commits
-
-
Stanislaw Gruszka authored
We use priv->mutex to avoid race conditions between chswitch_done() and mac_channel_switch(), when marking channel switch in progress. But chswitch_done() can be called in atomic context from rx_csa() or with mutex already taken from commit_rxon(). To fix remove mutex from chswitch_done() and use atomic bitops for marking channel switch pending. Cc: stable@kernel.org # 2.6.39+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Ignacy reports that sometimes after leaving an IBSS joining a new one didn't work because there still were stations on the list. He fixed it by flushing stations when attempting to join a new IBSS, but this shouldn't be happening in the first case. When I looked into it I saw a race condition in teardown that could cause stations to be added after flush, and thus cause this situation. Ignacy confirms that after applying my patch he hasn't seen this happen again. Reported-by: Ignacy Gawedzki <i@lri.fr> Debugged-by: Ignacy Gawedzki <i@lri.fr> Tested-by: Ignacy Gawedzki <i@lri.fr> Cc: stable@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
During channge channel, tx power will not send to uCode, the tx power command should send after scan complete. but should also can send after RXON command. Stable fix identified by Stanislaw Gruszka <sgruszka@redhat.com>. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Cc: stable@kernel.org [2.6.38+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 07 Jun, 2011 4 commits
-
-
Luciano Coelho authored
When one of the SSID's length passed in a scan or sched_scan request is larger than 255, there will be an overflow in the u8 that is used to store the length before checking. This causes the check to fail and we overrun the buffer when copying the SSID. Fix this by checking the nl80211 attribute length before copying it to the struct. This is a follow up for the previous commit 208c72f4, which didn't fix the problem entirely. Reported-by: Ido Yariv <ido@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mike McCormack authored
In the case we fail to allocate a new skb, the old skb should be resubmitted unmodified. Fixes bug introduced in a9e12869. Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mike McCormack authored
Should pass along packet if there's no CRC and no hardware error. Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
This reverts commit 1d38c16c. The mac80211 maintainer raised complaints about abuse of the CSA stop reason, and about whether this patch actually serves its intended purpose at all. Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 06 Jun, 2011 4 commits
-
-
Stanislaw Gruszka authored
Setting tx power can be deferred during scan or changing channel. If after that correct tx power settings will not be sent to device, we can observe transmission problems and timeouts. Force to send tx power settings also after partial rxon change, to assure device always be configured with up-to-date settings. Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=36492 Cc: stable@kernel.org # 2.6.39+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
Avoid queue and run autowakeup_work when device is not present anymore. That prevent rmmod and device remove crash introduced by: commit 1c0bcf89 Author: Ivo van Doorn <ivdoorn@gmail.com> Date: Sat Apr 30 17:18:18 2011 +0200 rt2x00: Add autowake support for USB hardware Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
This patch fixes 802.11n stability and performance regression we have since 2.6.35. It boost performance on my 5GHz N-only network from about 5MB/s to 8MB/s. Similar percentage boost can be observed on 2.4 GHz. These are test results of 5x downloading of approximately 700MB iso image: vanilla: 5.27 5.22 4.94 4.47 5.31 ; avr 5.0420 std 0.35110 patched: 8.07 7.95 8.06 7.99 7.96 ; avr 8.0060 std 0.055946 This was achieved with NetworkManager configured to do not perform periodical scans, by configuring constant BSSID. With periodical scans, after some time, performance downgrade to unpatched driver level, like in example below: patched: 7.40 7.61 4.28 4.37 4.80 avr 5.6920 std 1.6683 However patch still make better here, since similar test on unpatched driver make link disconnects with below messages after some time: wlan1: authenticate with 00:23:69:35:d1:3f (try 1) wlan1: authenticate with 00:23:69:35:d1:3f (try 2) wlan1: authenticate with 00:23:69:35:d1:3f (try 3) wlan1: authentication with 00:23:69:35:d1:3f timed out On 2.6.35 kernel patch helps against connection hangs with messages: iwlagn 0000:20:00.0: queue 10 stuck 3 time. Fw reload. iwlagn 0000:20:00.0: On demand firmware reload iwlagn 0000:20:00.0: Stopping AGG while state not ON or starting Cc: stable@kernel.org # 2.6.35+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
This reverts commit aac6af55. Conflicts: net/mac80211/key.c That commit has a race that causes a warning, as documented in the thread here: http://marc.info/?l=linux-wireless&m=130717684914101&w=2Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 03 Jun, 2011 5 commits
-
-
Daniel Drake authored
Commit 06e8935f adds an IRQ handling optimization for single-function SDIO cards like this one, but at the same time exposes a small hardware bug. During hardware init, an interrupt is generated with (apparently) no source. Previously, mmc threw this interrupt away, but now (due to the optimization), the mmc layer passes this onto libertas, before it is ready (and before it has enabled interrupts), causing a crash. Work around this hardware bug by registering the IRQ handler later and making it capable of handling interrupts with no cause. The change that makes the IRQ handler registration happen later actually eliminates the spurious interrupt as well. Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Thadeu Lima de Souza Cascardo authored
This partially reverts 1c5cae81, because the netdev name is copied into sdata->name, which is used for debugging messages, for example. Otherwise, we get messages like this: wlan%d: authenticated Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Cc: Jiri Pirko <jpirko@redhat.com> Cc: David S. Miller <davem@davemloft.net> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
We use priv->mutex to avoid race conditions between iwl_chswitch_done() and iwlagn_mac_channel_switch(), when marking channel switch in progress. But iwl_chswitch_done() can be called in atomic context from iwl_rx_csa() or with mutex already taken from iwlagn_commit_rxon(). These bugs were introduced by: commit 79d07325 Author: Wey-Yi Guy <wey-yi.w.guy@intel.com> Date: Thu May 6 08:54:11 2010 -0700 iwlwifi: support channel switch offload in driver To fix remove mutex from iwl_chswitch_done() and use atomic bitops for marking channel switch pending. Also remove iwl2030_hw_channel_switch() since 2000 series adapters are 2.4GHz only devices. Cc: stable@kernel.org # 2.6.36+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Nick Kossifidis authored
Disable fast channel change by default on AR2413/AR5413 due to some bug reports (it still works for me but it's better to be safe). Add a module parameter "fastchanswitch" in case anyone wants to enable it and play with it. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
We were incorrectly executing PCIe specific workarounds on PCI cards. This resulted in: Machine check in kernel mode. Caused by (from SRR1=149030): Transfer error ack signal Oops: Machine check, sig: 7 [#1] Reported-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 01 Jun, 2011 4 commits
-
-
Stanislaw Gruszka authored
In some cases we can read wrong temperature value. If after that temperature value will not be updated to good one, we badly configure tx power parameters and device is unable to send a data. Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=35932 Cc: stable@kernel.org # 2.6.39+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
read_lock() ... read_unlock_bh() is clearly bogus. This was broken by commit 23691d75 Author: Gustavo F. Padovan <padovan@profusion.mobi> Date: Wed Apr 27 18:26:32 2011 -0300 Bluetooth: Remove l2cap_sk_list Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Daniel Halperin authored
This is the same fix as commit 84105160 Author: Matteo Croce <technoboy85@gmail.com> Date: Fri Dec 3 02:25:08 2010 +0100 The ath9k driver subtracts 3 dBm to the txpower as with two radios the signal power is doubled. The resulting value is assigned in an u16 which overflows and makes the card work at full power. in two more places. I grepped the ath tree and didn't find any others. Cc: stable@kernel.org Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Eliad Peller authored
Commit 0a35d36d ("cfg80211: Use capability info to detect mesh beacons") assumed that probe response with both ESS and IBSS bits cleared means that the frame was sent by a mesh sta. However, these capabilities are also being used in the p2p_find phase, and the mesh-validation broke it. Rename the WLAN_CAPABILITY_IS_MBSS macro, and verify that mesh ies exist before assuming this frame was sent by a mesh sta. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 31 May, 2011 7 commits
-
-
Wey-Yi Guy authored
For 6150 devices, modify the supported PCI subsystem ID. Cc: stable@kernel.org Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jussi Kivilinna authored
zd1211 devices register 'EP 4 OUT' endpoint as Interrupt type on USB 2.0: Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 However on USB 1.1 endpoint becomes Bulk: Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Commit 37939810 assumed that endpoint is always interrupt type and changed usb_bulk_msg() calls to usb_interrupt_msg(). Problem here is that usb_bulk_msg() on interrupt endpoint selfcorrects the call and changes requested pipe to interrupt type (see usb_bulk_msg). However with usb_interrupt_msg() on bulk endpoint does not correct the pipe type to bulk, but instead URB is submitted with interrupt type pipe. So pre-2.6.39 used usb_bulk_msg() and therefore worked with both endpoint types, however in 2.6.39 usb_interrupt_msg() with bulk endpoint causes ohci_hcd to fail submitted URB instantly with -ENOSPC and preventing zd1211rw from working with OHCI. Fix this by detecting endpoint type and using correct endpoint/pipe types for URB. Also fix asynchronous zd_usb_iowrite16v_async() to use right URB type on 'EP 4 OUT'. Cc: stable@kernel.org Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luciano Coelho authored
Fix kernel oops when trying to use passive scheduled scans. The reason was that in passive scans there are no SSIDs, so there was a NULL pointer dereference. To solve the problem, we now check the number of SSIDs provided in the sched_scan request and only access the list if there's one or more (ie. passive scan is not forced). We also force all the channels to be passive by adding the IEEE80211_CHAN_PASSIVE_SCAN flag locally before the checks in the wl1271_scan_get_sched_scan_channels() function. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luciano Coelho authored
Use a different value for DFS dwell time when performing a scheduled scan. Previously we were using the same value as for normal passive scans. This adds some flexibility between these two different types of passive scan. For now we use 150 TUs for DFS channel dwell time. This may need to be fine-tuned in the future. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luciano Coelho authored
DFS channels were never getting included in the scheduled scans, because they always contain the passive flag as well and the call was asking for DFS and active channels. Fix this by ignoring the passive flag when collecting DFS channels. Also, move the DFS channels in the channel list before the 5GHz active channels (this was implemented in the FW differently than specified). Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luciano Coelho authored
We were comparing bitwise AND results with a boolean, so when the boolean was set to true, it was not matching as it should. Fix this by booleanizing the bitwise AND results with !!. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Daniel Drake authored
Before this patch, the command sequence number is being set before lbs_queue_cmd() adds the command to the queue. However, lbs_queue_cmd() sometimes forces commands to queue-jump (e.g. CMD_802_11_WAKEUP_CONFIRM). It currently does this without considering that sequence numbers might need adjusting to keep things running in order. Fix this by setting the sequence number at a later stage, just before we're actually submitting the command to the hardware. Also fixes a possible race where seqnum was being modified outside of the driver lock. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 27 May, 2011 13 commits
-
-
David S. Miller authored
Ingo Molnar noticed that we have this unnecessary ratelimit.h dependency in linux/net.h, which hid compilation problems from people doing builds only with CONFIG_NET enabled. Move this stuff out to a seperate net/net_ratelimit.h file and include that in the only two places where this thing is needed. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Ingo Molnar <mingo@elte.hu>
-
David S. Miller authored
Several networking headers were depending upon the implicit linux/sysctl.h include they get when including linux/net.h Add explicit includes. Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
This got missed back in 2006 when Jes Sorensen deleted net/ethernet/sysctl_net_ether.c Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Several crashes in cleanup_once() were reported in recent kernels. Commit d6cc1d64 (inetpeer: various changes) added a race in unlink_from_unused(). One way to avoid taking unused_peers.lock before doing the list_empty() test is to catch 0->1 refcnt transitions, using full barrier atomic operations variants (atomic_cmpxchg() and atomic_inc_return()) instead of previous atomic_inc() and atomic_add_unless() variants. We then call unlink_from_unused() only for the owner of the 0->1 transition. Add a new atomic_add_unless_return() static helper With help from Arun Sharma. Refs: https://bugzilla.kernel.org/show_bug.cgi?id=32772Reported-by: Arun Sharma <asharma@fb.com> Reported-by: Maximilian Engelhardt <maxi@daemonizer.de> Reported-by: Yann Dupont <Yann.Dupont@univ-nantes.fr> Reported-by: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dan Williams authored
It's currently exposed only through /proc which, besides requiring screen-scraping, doesn't allow userspace to distinguish between two identical ATM adapters with different ATM indexes. The ATM device index is required when using PPPoATM on a system with multiple ATM adapters. Signed-off-by: Dan Williams <dcbw@redhat.com> Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: David Woodhouse <dwmw2@infradead.org> Cc: stable@kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
-
-
Adrian Chadd authored
The AR9287 calibration code was not being called because of an incorrect MAC revision check. This forced the AR9287 to use the AR9285 initial calibration code and bypass the AR9287 code entirely. Signed-off-by: Adrian Chadd <adrian@freebsd.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Jesper Juhl authored
Commit 79f460ca add a duplicate linux/slab.h include to net/mac80211/scan.c - remove it. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Eliad Peller authored
local->ps_data wasn't cleared on disassociation, which (in some corner cases) caused reconnections to enter psm before association completed. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Tao Ma authored
We make oldconfig every time when a new kernel arrives, but if we don't have such a device(I guess this is the most common case for a new device), the default value should be 'n' so that the kernel size we build doesn't grow up too much quickly. For anyone who has the device, it is OK for them to turn it on by themselves. Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Tao Ma <boyu.mt@taobao.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
rx_status.band is used uninitialized, what disallow to work on 5GHz . Cc: stable@kernel.org # 2.6.39+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Hans Schillstrom authored
When ip_vs was adapted to netns the ftp application was not adapted in a correct way. However this is a fix to avoid kernel errors. In the long term another solution might be chosen. I.e the ports that the ftp appl, uses should be per netns. Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>