- 31 Mar, 2014 3 commits
-
-
Amitkumar Karwar authored
It has been observed that system hangs during suspend, if host sleep activation fails due to a missing interrupt from firmware. Use timeout variant, so that the thread will be woken up when timer expires. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
When a thread is interrupted by signal, all wait_event_interruptible calls after queueing commands return an error. Numbers of commands in pending queue are increased in this case. Sometimes all commands nodes in pool are filled. We will cancel pending commands when signal is received. Signed-off-by:
-
Amitkumar Karwar authored
When scan request is received, scan commands are prepared and queued into scan pending queue. There is a corner case when command nodes are full. So we stop queueing further scan commands and return an error. This patch makes sure that currently queued commands in scan pending queue are also freed in this case. Signed-off-by:
-
- 27 Mar, 2014 32 commits
-
-
Andrea Merello authored
update description in Kconfig to state rtl8180 driver now supports also rtl8187se cards Signed-off-by:
Andrea Merello <andrea.merello@gmail.com> Signed-off-by:
-
Andrea Merello authored
Finally make rtl8187se works (hopefylly). This patch adds PCI ID for rtl8187, updates copyright notes and updates MODULE_DESCRIPTION. Signed-off-by:
-
Andrea Merello authored
Add case to detect the rtl8187se card and its RF frontend. In this case set also accordingly mac80211 queue number. Signed-off-by:
-
Andrea Merello authored
Introduce a new function to configure AC parameters for TX queues on rtl8187se cards, and hook it onto mac80211 in order to enable WMM support. Signed-off-by:
-
Andrea Merello authored
MSR register for rtl8187se must always have ENEDCA flag set. Write it accordingly when updated on BSS change. Signed-off-by:
-
Andrea Merello authored
This patch adds ERP configuration support for rtl8187se to the existing ERP configuration function. It needs a different register offset and it must not apply rtl8185 workaround. Signed-off-by:
-
Andrea Merello authored
This patch adds few functions that initializes extra stuff that is present only in rtl8187se HW, and it modify the existing HW initialization function where necessary Signed-off-by:
-
Andrea Merello authored
This patch introduce new RF code for rtl8225 zebra v4 radio frontend. This code contains a lot of black magic and it can work probably only with the radio embdedded in the rtl8187se single-chip. Signed-off-by:
-
Andrea Merello authored
rtl8180 has one register for analog converters setting ,rtl8185 has two and rtl8187se has three. Setting those registers require more than a simple write, and for one of them a function is already provided. This patch introduces functions for the other two. rtl8187se will use them. rtl8185 doesen't yet, but should Signed-off-by:
-
Andrea Merello authored
rtl8187se nees extra parameters to be read from the eeprom. This patch adds support for it Signed-off-by:
-
Andrea Merello authored
configuration of carbus-related registers is different for rtl8187se. Introduce a dedicated function that does it for all cards in the proper way Signed-off-by:
-
Andrea Merello authored
This patch adds tx queue mapping for rtl8187se and a long comment block about their usages. It adapts the TX function to use that map and it sets properly the TX descriptor rtl8187se-only fields Signed-off-by:
-
Andrea Merello authored
MAR registers are not present in rtl8187se, and attempting to write to them must be avoided Signed-off-by:
-
Andrea Merello authored
This patch introduces two dedicated functions for enabling and disabling ints. Support for rtl8187se is also added to them Signed-off-by:
-
Andrea Merello authored
rtl8187se has more queues and different ISR flags. This patch adds a separated ISR handler for rtl8187se Signed-off-by:
-
Andrea Merello authored
Currently RX status descriptor and RX command descriptor are represented using the same struct type. This patch splits this by introducing different types for rx status and command descriptor. Doing this make it possible to handle rtl8187se RX descriptors easier. This patch do also this by adding specific cases where needed. Signed-off-by:
-
Andrea Merello authored
Basic rate configuration is a bit different for rtl8187se. Adding this also fixes the gcc warning introduced in last patch about unhandled case in switch. Signed-off-by:
-
Andrea Merello authored
This patch modifies the TX descriptor struct so it can work also for rtl8187se. Some reserved field is now meaningful, and where needed union is used. Signed-off-by:
-
Andrea Merello authored
Add back rtl8187se chip type to the enum for known chips. This causes unhandled switch/case warning that will be fixed in following patch Signed-off-by:
-
Andrea Merello authored
Adds registers for rtl8187se to the rtl818x common struct Signed-off-by:
-
Amitkumar Karwar authored
Sometimes we may end up downloading other commands when host sleep is configured. This patch makes sure that pending commands are cancelled and we stop queueing further commands during host sleep. Signed-off-by:
-
Amitkumar Karwar authored
Incremented sequence number was not being used for SLEEP confirm command. This patch fixes the issue. Signed-off-by:
-
Amitkumar Karwar authored
When next scan command is delayed due to Tx traffic and meanwhile synchronous command is received followed by a signal, we cance all pending commands. NULL pointer dereference is seen in this case while queueing next command in scan delay timer. This patch adds a check to fix this issue. Signed-off-by:
-
Daniel Kim authored
The struct cfg80211_connect_params indicate whether the connection should use management frame protection (mfp). If required set the MFP_CAPABLE flag in the firmware command. This is supported from user-space by wpa_supplicant since v2.1. Reviewed-by:
Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Joe Perches authored
Casting a pointer to a pointer of the same type is pointless, so remove these unnecessary casts. Around these changes: o Remove unnecessary parentheses o Use consistent dereference style (change ptr[0] to *ptr) o Argument alignment Done via coccinelle script: (and some typing) $ cat typecast_2.cocci @@ type T; T *foo; @@ - (T *)foo + foo Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Joe Perches authored
Casting a pointer to a pointer of the same type is pointless, so remove these unnecessary casts. Done via coccinelle script: $ cat typecast_2.cocci @@ type T; T *foo; @@ - (T *)foo + foo Signed-off-by:
-
Joe Perches authored
Casting a pointer to a pointer of the same type is pointless, so remove these unnecessary casts. Done via coccinelle script: $ cat typecast_2.cocci @@ type T; T *foo; @@ - (T *)foo + foo Signed-off-by:
-
Joe Perches authored
Using addressof then casting to the original type is pointless, so remove these unnecessary casts. Done via coccinelle script: $ cat typecast.cocci @@ type T; T foo; @@ - (T *)&foo + &foo Signed-off-by:
-
Andrea Merello authored
On currently supported HW there are four TX queues (three for normal packets and one for beacons). The driver uses just one TX queue, and declare to mac80211 to support just one queue, but it allocates coherent memory for all queues. Furthermore the TX is code is written assumimg four queues exists, and even if we decide to enable more queues in future, its mapping rule to mac80211 is fixed. This means we have memory waste on rtl8180/rtl8185, and we have also not enough flexibility to add support for boards (rtl8187se) that will use more queues. This patch changes things in order to allocate coherent memory only for the queues effectively used and it make it possible to specify how to map hardware queues on mac80211 queues, that will be used by rtl8187se code as soon it will be merged. Note: even if the beacon queue is currently unused, this should change, so I kept it. Signed-off-by:
-
Andrea Merello authored
Hw DMA registers are written in rtl8180_init_hw function. They are also written again just after calling rtl8180_init_hw. There is no point in doing this twice. Remove those redundant register writes from rtl8180_start. Signed-off-by:
-
Rafał Miłecki authored
Some Broadcom boards have more GPIOs available. For example Linksys E3200 home router is based on SoC id 0x5357, package 0x0A and uses GPIO 23 to reset internal USB WiFi (gpio23=wombo_reset). Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
John W. Linville authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
-
- 26 Mar, 2014 1 commit
-
-
Johan Hedberg authored
We should let user space request the peer address also in the pending connect states, i.e. BT_CONNECT and BT_CONNECT2. There is existing user space code that tries to do this and will fail without extending the set of allowed states for the peer address information. This patch adds the two states to the allowed ones in the L2CAP and RFCOMM sock_getname functions, thereby preventing ENOTCONN from being returned. Reported-by:
Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Tested-by:
Marcel Holtmann <marcel@holtmann.org>
-
- 24 Mar, 2014 4 commits
-
-
Johan Hedberg authored
The smp variable in smp_conn_security is not used anywhere before the smp = smp_chan_create() call in the smp_conn_security function so it makes no sense to assign any other value to it before that. Signed-off-by:
-
Johan Hedberg authored
The smp pointer might not be initialized for jumps to the "done" label in the smp_conn_security function. Furthermore doing the set_bit after done might "overwrite" a previous value of the flag in case pairing was already in progress. This patch moves the call to set_bit before the label so that it is only done for a newly created smp context (as returned by smp_chan_create). Signed-off-by:
-
Johan Hedberg authored
Due to several devices being unable to handle this procedure reliably (resulting in forced disconnections before pairing completes) it's better to remove it altogether. Signed-off-by:
-
Johan Hedberg authored
In the case that the just-works model would be triggered we only want to confirm remotely initiated pairings (i.e. those triggered by a Security Request or Pairing Request). This patch adds the necessary check to the tk_request function to fall back to the JUST_WORKS method in the case of a locally initiated pairing. Signed-off-by:
-
