Add Mobileye EyeQ5 compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240410-cdns-qspi-mbly-v3-2-7b7053449cf7@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Compatibles are ordered by date of addition.
Switch to (deterministic) alphabetical ordering.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240410-cdns-qspi-mbly-v3-1-7b7053449cf7@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

cqspi_enable_dtr() is called for each operation, commands or not, reads
or writes. It writes CQSPI_REG_CONFIG then waits for idle (three
successful reads). Skip that in the no-DTR case if DTR is already
disabled.

It cannot be skipped in the DTR case as cqspi_setup_opcode_ext() writes
to a register and we must wait for idle state.

According to ftrace, the average cqspi_exec_mem_op() call goes from
85.4µs to 83.6µs when reading 235M over UBIFS on an octal flash.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240405-cdns-qspi-mbly-v2-6-956679866d6d@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Avoid of_device_get_match_data() call on each IRQ and each read
operation. Store pointer in `struct cqspi_st` device instance.

End-to-end performance measurements improve with this patch. On a given
octal flash, reading 235M over UBIFS is ~3.4% faster. During that read,
the average cqspi_exec_mem_op() call goes from 85.4µs to 80.7µs
according to ftrace. The worst case goes from 622.4µs to 615.2µs.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240405-cdns-qspi-mbly-v2-4-956679866d6d@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

The Cadence QSPI Controller driver is used on Mobileye EyeQ5 platform.
Allow building on MIPS.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://msgid.link/r/20240405-cdns-qspi-mbly-v2-3-956679866d6d@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

pxa_ssp_request() implies a reference counting, hence the pxa_ssp_free()
must be called when we are done. Add missed call.

Fixes: bb77c99e ("spi: pxa2xx: Skip SSP initialization if it's done elsewhere")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240402144523.3402063-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Core in spi_register_driver() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240328203927.156184-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

kernel-doc complains about last_cs_index_mask not described, so add its
description.

spi.h:778: warning: Function parameter or struct member 'last_cs_index_mask' not described in 'spi_controller'

Fixes: 4d8ff6b0 ("spi: Add multi-cs memories support in SPI core")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240328223340.17159-1-rdunlap@infradead.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from David Lechner <dlechner@baylibre.com>:

I found a couple more controller drivers that were checking if the
tx_buf and rx_buf fields in the spi_transfer structure were set by a
peripheral driver that I missed in [1]. These checks can be removed
as well.

[1]: https://lore.kernel.org/linux-spi/20240325-spi-remove-is_dma_mapped-v2-1-d08d62b61f1c@baylibre.com/

Merge series from Louis Chauvet <louis.chauvet@bootlin.com>:

This series adds the support for the omap-mcspi multi mode which allows
sending SPI messages with a shorter delay between CS and the message.

One drawback of the multi-mode is that the CS is raised between each word,
so it can only be used with messages containing 1 word transfers and
asking for cs_change. Few devices, like FPGAs, may easily workaround this
limitation.

The first patch removes the current implementation, which is working, but
don't comply with what is asked in the spi transfer (The CS is raised by
the hardware regardless of cs_change state). No drivers or board file use this
implementation upstream.

The second patch adds the implementation of the multi-mode, which complies
with what is asked in the SPI message.

The third patch is the suggested optimization for using MULTI mode in more
situations.

There are no more peripheral drivers that set t->tx_dma or t->rx_dma.
Therefore, is_dma_mapped is always false and can be removed.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240328-spi-more-tx-rx-buf-cleanup-v1-2-9ec1ceedf08c@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

There are no more peripheral drivers that set t->tx_dma or t->rx_dma so
these will always == 0. Therefore, we can remove these checks since
they are always true.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240328-spi-more-tx-rx-buf-cleanup-v1-1-9ec1ceedf08c@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

If SSP has been enumerated elsewhere, skip its initialization
in pxa2xx_spi_init_pdata().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240327193138.2385910-5-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Refactor pxa2xx_spi_init_pdata() by extracting a new
pxa2xx_spi_init_ssp() helper which makes code less
twisted. It will be easier to continue refactoring for
a new coming modification.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240327193138.2385910-4-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Drop rather useless use of ACPI_PTR() and of_match_ptr().
It also removes the necessity to be dependent of.h inclusion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240327193138.2385910-3-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The PCI || ACPI dependency is the historical part of the x86 support.
Narrow the Kconfig option visibility by limiting this dependency to x86.

The drop of x86 for PCI case had happened in the commit 2b49ebda
("spi/pxa2xx: allow building on a 64-bit kernel"), while the ACPI
was specifically added for Intel Lynx Point in the commit a3496855
("spi/pxa2xx: add support for Lynxpoint SPI controllers").

Note that X86 covers both 32- and 64-bit variants.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240327193138.2385910-2-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Enable multimode when a transfer of multiple small words can be
transformed in a transfer with a single bigger word. This is allowed as
long as the result on the cable is the same, so word_delay must be zero.
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://msgid.link/r/20240327-spi-omap2-mcspi-multi-mode-v3-3-c4ac329dd5a2@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Introduce support for MULTI-mode in the OMAP2 MCSPI driver. Currently, the
driver always uses SINGLE mode to handle the chip select (CS). With this
enhancement, MULTI-mode is enabled for specific messages, allowing for a
shorter delay between CS enable and the message (some FPGA devices are
sensitive to this delay).

The OMAP2 MCSPI device can use two different mode to send messages, SINGLE
and MULTI:
In SINGLE mode, the controller only leverages one single FIFO, and the
host system has to manually select the CS it wants to enable.
In MULTI mode, each CS is bound to a FIFO, the host system then writes the
data to the relevant FIFO, as the hardware will take care of the CS

The drawback of multi-mode is that it's not possible to keep the CS
enabled between each words. Therefore, this patch enables multi-mode only
for specific messages: the spi_message must contain only spi_transfer of 1
word (of any size) with cs_change enabled.

A new member is introduced in the omap2_mcspi structure to keep track of
the current used mode.
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://msgid.link/r/20240327-spi-omap2-mcspi-multi-mode-v3-2-c4ac329dd5a2@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 5cbc7ca9 ("spi: spi-omap2-mcspi.c: Toggle CS after each
word") introduced the toggling of CS after each word for the omap2-mcspi
controller.

The implementation is not respectful of the actual spi_message
content, so the CS can be raised after each word even if the
transfer structure asks to keep the CS active for the whole operation.

As it is not used anyway in the current Linux tree, it can be safely
removed.
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://msgid.link/r/20240327-spi-omap2-mcspi-multi-mode-v3-1-c4ac329dd5a2@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240327174737.519637-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240327174737.519637-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Core in spi_register_driver() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240327174737.519637-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Switch to use dev_err_probe() to simplify the error path and
unify a message template.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240326181027.1418989-4-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Keep the PXA*_SSP types together in enum pxa_ssp_type
for better maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240326181027.1418989-3-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:

Fix kernel documentation and inclusion block, and dropping the size
of the num_chipselect.

Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:

A couple of cleanups against linux/spi/pxa2xx_spi.h.

I'm sending this as v3 to land in the SPI subsystem. Meanwhile I'm
preparing an update to make linux/spi/pxa2xx_spi.h private to the
subsystem (PXA2xx driver). But the second part will be presented later
on (likely after v6.9-rc1). That said, this can be routed either via
SoC tree or SPI, up to respective maintainers.

There are no more users of the deprecated is_dma_mapped in struct
spi_message so it can be removed.

References in documentation and comments are also removed.

A few similar checks if xfer->tx_dma or xfer->rx_dma are not NULL are
also removed since these are now guaranteed to be NULL because they
were previously set only if is_dma_mapped was true.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240325-spi-remove-is_dma_mapped-v2-1-d08d62b61f1c@baylibre.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support to the SPI controller driver to use SPI MEM framework.
SPI subsystem utilizing the SPI memory operations allows to re-use
SPI controller drivers for both SPI NOR devices, regular SPI devices
as well as SPI NAND devices.

Add below functions of spi_mem_ops to support SPI MEM framework
- exec-op(): to execute the memory operations.
- supports_op(): to check if the memory operation is supported.
- adjust_op_size(): to split data transfers so that they don’t exceed the
  max transfer size supported by the controller.
Suggested-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Co-developed-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Signed-off-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://msgid.link/r/20240229134544.3461757-1-Raju.Rangoju@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

No in-kernel users of struct rspi_plat_data. If required,
the software nodes should be used for such users. For now
just get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240325142118.3210915-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

All the spi_transfer variables in this file use the name "xfer" except
the one in mtk_spi_interrupt(). Align the naming for consistency and
easier searching.

While at it, reformat one memcpy() usage since the coding style allows
100 column lines today.

This commit has no functional change.
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240321070942.1587146-3-fshao@chromium.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Extract a magic number, from mt7621_spi_probe(), used to
declare the number of chip select lines (which co-incides
with the native chip select count of 2) to a macro.

Use the newly defined MT7621_NATIVE_CS_COUNT macro to
instead populate both the spi_controller's max_native_cs
and num_chipselect members.

Declare that the spi_controller should use_gpio_descriptors
if present in the device properties (such as those declared
in the cs-gpio property of a "ralink,mt7621-spi" compatible
device-tree node) so that the SPI core will recalculcate
num_chipselect to account for the GPIO descriptors that
it should have populated in the cs_gpiod array member.

Remove the assignment of mt7621_spi_transfer_one_message()
to the spi_controller's transfer_one_message hook.

Refactor the mt7621_spi_transfer_one_message() logic into
mt7621_spi_prepare_message() and mt7621_spi_transfer_one()
and assign both to the spi_controller's prepare_message
and transfer_one hooks respectively.

Migrate the call mt7621_spi_transfer_one_message() made to
mt7621_spi_flush() just before chip select deactivation,
to the end of mt7621_spi_write_half_duplex() to ensure
that any pending data is shifted out of MOSI before the SPI
core deactivates the chip select line.

As chip select activation is now taken care of by the SPI
core, due to the use of the transfer_one hook instead of
transfer_one_message, the calls to mt7621_spi_set_cs()
from mt7621_spi_transfer_one_message() have fallen away.

And although the SPI core will handle activation for GPIO
chip select lines behind the scenes, it requires a callback
to allow the driver to perform controller-specific
operations to control its native chip select lines.

Rename mt7621_spi_set_cs() to mt7621_spi_set_native_cs()
and make sure that it takes into account the activation
polarity of the chip select line it's acting upon, as the
passed enable parameter represents the desired line level
and not the desired activation state, and then assign
mt7621_set_cs() to the spi_controller's set_cs hook.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://msgid.link/r/20240316010302.20776-1-justin.swartz@risingedge.co.zaReviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There is nothing from pxa2xx_spi.h used by soc/pxa/ssp.c.
Replace it with pxa2xx_ssp.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://msgid.link/r/20240307195056.4059864-4-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

There is no use for whole 16-bit for the number of chip select pins.
Drop it to 8 bits.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240307195056.4059864-3-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

There is the only one user of the pxa2xx_set_spi_info(). Unexport it
and inline to the actual user.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://msgid.link/r/20240307195056.4059864-2-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

There is no use for whole 16-bit for the number of chip select pins.
Drop it to 8 bits and reshuffle the data structure layout to avoid
unnecessary paddings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://msgid.link/r/20240308162920.46816-4-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

xilinx_spi.h is mnissing inclusion and forward declaration, add them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://msgid.link/r/20240308162920.46816-3-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

While updating the data structure layout the kernel documentation
became outdated. Synchronize kernel documentation with the actual
data structure layout.

Fixes: 1dd46599 ("spi: xilinx: add force_irq for QSPI mode")
Fixes: 082339bc ("spi: spi-xilinx: Add run run-time endian detection")
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240308162920.46816-2-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Pull EFI fixes from Ard Biesheuvel:

 - Fix logic that is supposed to prevent placement of the kernel image
   below LOAD_PHYSICAL_ADDR

 - Use the firmware stack in the EFI stub when running in mixed mode

 - Clear BSS only once when using mixed mode

 - Check efi.get_variable() function pointer for NULL before trying to
   call it

* tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
  efi: fix panic in kdump kernel
  x86/efistub: Don't clear BSS twice in mixed mode
  x86/efistub: Call mixed mode boot services on the firmware's stack
  efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address

Pull x86 fixes from Thomas Gleixner:

 - Ensure that the encryption mask at boot is properly propagated on
   5-level page tables, otherwise the PGD entry is incorrectly set to
   non-encrypted, which causes system crashes during boot.

 - Undo the deferred 5-level page table setup as it cannot work with
   memory encryption enabled.

 - Prevent inconsistent XFD state on CPU hotplug, where the MSR is reset
   to the default value but the cached variable is not, so subsequent
   comparisons might yield the wrong result and as a consequence the
   result prevents updating the MSR.

 - Register the local APIC address only once in the MPPARSE enumeration
   to prevent triggering the related WARN_ONs() in the APIC and topology
   code.

 - Handle the case where no APIC is found gracefully by registering a
   fake APIC in the topology code. That makes all related topology
   functions work correctly and does not affect the actual APIC driver
   code at all.

 - Don't evaluate logical IDs during early boot as the local APIC IDs
   are not yet enumerated and the invoked function returns an error
   code. Nothing requires the logical IDs before the final CPUID
   enumeration takes place, which happens after the enumeration.

 - Cure the fallout of the per CPU rework on UP which misplaced the
   copying of boot_cpu_data to per CPU data so that the final update to
   boot_cpu_data got lost which caused inconsistent state and boot
   crashes.

 - Use copy_from_kernel_nofault() in the kprobes setup as there is no
   guarantee that the address can be safely accessed.

 - Reorder struct members in struct saved_context to work around another
   kmemleak false positive

 - Remove the buggy code which tries to update the E820 kexec table for
   setup_data as that is never passed to the kexec kernel.

 - Update the resource control documentation to use the proper units.

 - Fix a Kconfig warning observed with tinyconfig

* tag 'x86-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/64: Move 5-level paging global variable assignments back
  x86/boot/64: Apply encryption mask to 5-level pagetable update
  x86/cpu: Add model number for another Intel Arrow Lake mobile processor
  x86/fpu: Keep xfd_state in sync with MSR_IA32_XFD
  Documentation/x86: Document that resctrl bandwidth control units are MiB
  x86/mpparse: Register APIC address only once
  x86/topology: Handle the !APIC case gracefully
  x86/topology: Don't evaluate logical IDs during early boot
  x86/cpu: Ensure that CPU info updates are propagated on UP
  kprobes/x86: Use copy_from_kernel_nofault() to read from unsafe address
  x86/pm: Work around false positive kmemleak report in msr_build_context()
  x86/kexec: Do not update E820 kexec table for setup_data
  x86/config: Fix warning for 'make ARCH=x86_64 tinyconfig'