If the first virtual interface is a station (or an AP with beacons
temporarily disabled), the beacon of the second interface needs to
occupy hardware beacon slot 0.
For some reason the beacon index was incorrectly masked with the
virtual interface beacon mask, which prevents the secondary
interface from sending beacons unless the first one also does.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>

ps-poll response frames can be sent via drv_tx. Store the frame sequence number
for such frames, in case a BlockAckReq needs to be sent
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Hardware station lookup for pspoll frames can fail, which makes the driver
ignore ps-poll frames. Fix the resulting powersave issues by looking up
the station for pspoll frames in software
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x0u_tx_prepare_skb routine in usb module in
order to remove leftover usb dependency from generic code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Read eeprom data from mtd memory by default and fall-back
to efuse if it fails
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mt76x0e_start and mt76x0e_stop mac80211
callbacks to start/stop device mac opening/closing
the netdevice
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add ieee80211_ops ops pointer to mt76x0_alloc_device routine signature
in order to specify mac80211 callbacks and remove usb dependency from
mt76x0 generic code.
Move mt76x0_ops callbacks in usb module in order to remove leftover
usb dependency in mt76x0 generic code.
Introduce mt76x0e_ops mac80211 callbacks for pci code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_phy_set_rxpath and mt76x02_phy_tx_dac routines in
mt76x02_phy.c since they are shared between mt76x2 and mt76x0 drivers.
Moreover move chainmask variable from mt76x2/mt76x0 to mt76_dev data
structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x0_ant_select routine in __mt76x0_phy_set_channel in order to
configure antenna parameters according to the current wireless channel
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add mt76x0e_register_device routine in pci.c
to initialize the device during hw probe.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move usb initialization code in mt76x0-usb module in
order to remove usb dependency from generic init code
(not completed yet). Moreover fix a memory leak in usb probe
if mt76x02_wait_for_mac fails
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mt76x02_mac_start since the mac start code is shared between
mt76x0e and mt76x2 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Initialize rxfilter mask at bootstrap an not at mac start.
This is a preliminary patch to share mt76x2_mac_start routine
between mt76x2e and mt76x0e drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Remove MT_PBF_SYS_CTRL configuration in mt76x0_reset_csr_bbp since
it is already initialized in mt76x0_init_mac_registers routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Remove MT_HEADER_TRANS_CTRL_REG/MT_TSO_CTRL configuration
since they are already initialized in mt76x0_init_mac_registers
routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76x02_wait_for_wpdma and mt76x02_wait_for_txrx_idle
utility routines in mt76x0_init_hardware and mt76x0_mac_start
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move usb mcu code in a dedicated source file in order to remove
usb dependency from generic source files and improve code
maintainability
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move pci mcu code in a dedicated source file in order to
improve maintainability and facilitate new device support
development
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Update mac/rf/dcoc initial values to latest version of vendor driver.
Improve code readability
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x2_wait_for_bbp utility routine in mt76x02_util.h
in order to be resued by mt76x0 driver. Morover rename it in
mt76x02_wait_for_txrx_idle
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mmio implementation of mt76_mmio_rd_rp and
mt76_mmio_wr_rp and remove mt76x2 duplicated code.
mt76_mmio_{wr,rd}_rp allows to reuse mt76x0 init code
adding mt76x0e support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_beacon_offset utility routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 driver and remove
duplicated code. Moreover move beacon_offset data structure in
mt76x02-lib module since it is shared between mt76x0 and mt76x2
drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_dma_init, mt76x02_init_rx_queue and mt76x02_init_tx_queue
routines in mt76x02-lib module in order to be reused by mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_set_irq_mask, mt76x02_irq_enable and mt76x02_irq_disable
in mt76x02-lib module in order to be reused by mt76x0 driver.
Moreover move irq_lock and irqmask in mt76_mmio data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mt76x02_dma_enable and mt76x02_dma_disable utility routines
in order to be reused in mt76x0 mac configuration and remove duplicated
code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move wait_for_wpdma utility routine in mt76x02_dma.h
in order to be reused by mt76x0 driver. Moreover add
the possibility to specify the timeout value in
wait_for_wpdma signature
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76_poll utility routine in mt76x0_set_wlan_state to check
if the PLL/XTAL is ready
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

If the WLAN core is still active during initialization, it might cause
the MCU or DMA to hang. This can happen during soft reboot, so disable
the core + clock early to avoid this issue.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

TP-LINK Archer T1U do not support 2.4GHz band despite EEPROM
reports that. Add quirk to mask out 2.4GHz support.
Reported-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt76 uses __skb_pad() with free_on_error set to true, this is the same
as calling skb_pad().
This patch does not change any functionality, but it makes it easier to
backport this driver in backports, because skb_pad() is also available
in older kernel versions.

Fixes: b40b15e1 ("mt76: add usb support to mt76 layer")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add rx_page_lock spinlock in order to make rx page fragment access
atomic. This patch fixes the following crash that occasionally
occurs during module loading/unloading

BUG: unable to handle kernel paging request at ffff9f8322e19000
PGD 27ba01067 P4D 27ba01067 PUD 27ddba063 PMD 263b35063 PTE 8000000262e19061
Oops: 0003 [#1] SMP PTI
CPU: 2 PID: 1766 Comm: systemd-udevd Not tainted 4.19.0-rc5+ #6
Hardware name: ASUSTeK COMPUTER INC. ESC2000 G2/Z9PE-D8 WS, BIOS 0405 03/19/2012
RIP: 0010:__memcpy+0x12/0x20
RSP: 0018:ffffba13849b3ad8 EFLAGS: 00010246
RAX: ffff9f8322e17004 RBX: 00000000000038f0 RCX: 000000000000031f
RDX: 0000000000000000 RSI: ffffba13844cf058 RDI: ffff9f8322e18ffc
RBP: 0000000000010c6c R08: 0000000000000000 R09: 0000607ec0000000
R10: 0000000000000003 R11: 0000000000003e2e R12: ffff9f8324cd9540
R13: 0000000000000000 R14: ffffba13849b3b30 R15: ffff9f8322e17000
FS:  00007fadec85b880(0000) GS:ffff9f833fa80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9f8322e19000 CR3: 0000000263428001 CR4: 00000000000606e0
Call Trace:
 mt76x02u_mcu_fw_send_data+0x16c/0x270 [mt76x02_usb]
 mt76x0u_probe+0x35a/0x598 [mt76x0u]
 usb_probe_interface+0x113/0x310
 really_probe+0x1c8/0x400
 driver_probe_device+0x5c/0x130
 __driver_attach+0xec/0x110
 bus_for_each_dev+0x50/0x90
 bus_add_driver+0x1c0/0x280
 driver_register+0x5b/0xe0
 usb_register_driver+0x7c/0x140
 do_one_initcall+0x44/0x19b
 do_init_module+0x5a/0x210
 load_module+0x175c/0x1bc0
 __do_sys_finit_module+0x97/0xc0
 do_syscall_64+0x3f/0xf0
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fadeb6f1809
RSP: 002b:00007ffe548f9f38 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 00007fadebdf0d89 RCX: 00007fadeb6f1809
RDX: 0000000000000000 RSI: 00007fadebdf0d89 RDI: 0000000000000006
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000006 R11: 0000000000000246 R12: 0000560b9ef58ab0
R13: 0000560b9ef29800 R14: 0000560b9ef59040 R15: 0000000000020000

Fixes: c12128ce ("mt76: use a per rx queue page fragment cache")
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

print fw_ver and build_ver members of struct mt76x02_fw_header, similarly
to what appears in the output of 'dmesg' when the MCU firmware is loaded.
Reported-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fix source files using MODULE_* macros without including linux/module.h
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add mt76x0_phy_set_txpower routine in order to configure
base and per rate tx power gain. Moreover take into account
txpower_conf in order to limit the tx power gain according to
the bound provided by mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use mt76 shared debugfs implementation and remove duplicated code
in mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_get_power_info routine.
Remove mt76x0_eeprom_params since it is now an empty structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

In order to unify eeprom parsing between mt76x0 and mt76x2 drivers,
remove eeprom pointer dependency from mt76x0_set_tx_power_per_rate.
Moreover use mt76_rate_power to store power vs rate calibration data.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Remove mt76x0_extra_power_over_mac and mt76x0_phy_set_tx_power routines
since they are not actually used and tx power handling will be unified
with mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move mt76x02_rate_power_val and mt76x2_sign_extend_optional utility
routines in mt76x02_eeprom.h in order to reuse them in mt76x0 eeprom
parsing
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Move rate_txpower handler in mt76 debugfs in order to be reused
in mt76x0 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>