- 28 Jan, 2019 12 commits
-
-
Chris Wilson authored
Allocate a page for use as a status page by a group of timelines, as we only need a dword of storage for each (rounded up to the cacheline for safety) we can pack multiple timelines into the same page. Each timeline will then be able to track its own HW seqno. v2: Reuse the common per-engine HWSP for the solitary ringbuffer timeline, so that we do not have to emit (using per-gen specialised vfuncs) the breadcrumb into the distinct timeline HWSP and instead can keep on using the common MI_STORE_DWORD_INDEX. However, to maintain the sleight-of-hand for the global/per-context seqno switchover, we will store both temporarily (and so use a custom offset for the shared timeline HWSP until the switch over). v3: Keep things simple and allocate a page for each timeline, page sharing comes next. v4: I was caught repeating the same MI_STORE_DWORD_IMM over and over again in selftests. v5: And caught red handed copying create timeline + check. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128181812.22804-3-chris@chris-wilson.co.uk
-
Chris Wilson authored
Previously we only accommodated having a vma pinned by a small number of users, with the maximum being pinned for use by the display engine. As such, we used a small bitfield only large enough to allow the vma to be pinned twice (for back/front buffers) in each scanout plane. Keeping the maximum permissible pin_count small allows us to quickly catch a potential leak. However, as we want to split a 4096B page into 64 different cachelines and pin each cacheline for use by a different timeline, we will exceed the current maximum permissible vma->pin_count and so time has come to enlarge it. Whilst we are here, try to pull together the similar bits: Address/layout specification: - bias, mappable, zone_4g: address limit specifiers - fixed: address override, limits still apply though - high: not strictly an address limit, but an address direction to search Search controls: - nonblock, nonfault, noevict v2: Rewrite the guideline comment on bit consumption. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: John Harrison <john.C.Harrison@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128181812.22804-2-chris@chris-wilson.co.uk
-
Chris Wilson authored
Supplement the per-engine HWSP with a per-timeline HWSP. That is a per-request pointer through which we can check a local seqno, abstracting away the presumption of a global seqno. In this first step, we point each request back into the engine's HWSP so everything continues to work with the global timeline. v2: s/i915_request_hwsp/hwsp_seqno/ to emphasis that this is the current HW value and that we are accessing it via i915_request merely as a convenience. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128181812.22804-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
Currently, the list of timelines is serialised by the struct_mutex, but to alleviate difficulties with using that mutex in future, move the list management under its own dedicated mutex. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128102356.15037-5-chris@chris-wilson.co.uk
-
Chris Wilson authored
Currently we only allocate an object and vma if we are using a GGTT virtual HWSP, and a plain struct page for a physical HWSP. For convenience later on with global timelines, it will be useful to always have the status page being tracked by a struct i915_vma. Make it so. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128102356.15037-4-chris@chris-wilson.co.uk
-
Chris Wilson authored
Remove the struct_mutex requirement for looking up the vma for an object. v2: Highlight how the race for duplicate vma creation is resolved on reacquiring the lock with a short comment. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128102356.15037-3-chris@chris-wilson.co.uk
-
Chris Wilson authored
A starting point to counter the pervasive struct_mutex. For the goal of avoiding (or at least blocking under them!) global locks during user request submission, a simple but important step is being able to manage each clients GTT separately. For which, we want to replace using the struct_mutex as the guard for all things GTT/VM and switch instead to a specific mutex inside i915_address_space. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128102356.15037-2-chris@chris-wilson.co.uk
-
Chris Wilson authored
Our goal is to remove struct_mutex and replace it with fine grained locking. One of the thorny issues is our eviction logic for reclaiming space for an execbuffer (or GTT mmaping, among a few other examples). While eviction itself is easy to move under a per-VM mutex, performing the activity tracking is less agreeable. One solution is not to do any MRU tracking and do a simple coarse evaluation during eviction of active/inactive, with a loose temporal ordering of last insertion/evaluation. That keeps all the locking constrained to when we are manipulating the VM itself, neatly avoiding the tricky handling of possible recursive locking during execbuf and elsewhere. Note that discarding the MRU (currently implemented as a pair of lists, to avoid scanning the active list for a NONBLOCKING search) is unlikely to impact upon our efficiency to reclaim VM space (where we think a LRU model is best) as our current strategy is to use random idle replacement first before doing a search, and over time the use of softpinned 48b per-ppGTT is growing (thereby eliminating any need to perform any eviction searches, in theory at least) with the remaining users being found on much older devices (gen2-gen6). v2: Changelog and commentary rewritten to elaborate on the duality of a single list being both an inactive and active list. v3: Consolidate bool parameters into a single set of flags; don't comment on the duality of a single variable being a multiplicity of bits. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128102356.15037-1-chris@chris-wilson.co.uk
-
Ville Syrjälä authored
Certain SNB machines (eg. ASUS K53SV) seem to have a broken BIOS which misprograms the hardware badly when encountering a suitably high resolution display. The programmed pipe timings are somewhat bonkers and the DPLL is totally misprogrammed (P divider == 0). That will result in atomic commit timeouts as apparently the pipe is sufficiently stuck to not signal vblank interrupts. IIRC something like this was also observed on some other SNB machine years ago (might have been a Dell XPS 8300) but a BIOS update cured it. Sadly looks like this was never fixed for the ASUS K53SV as the latest BIOS (K53SV.320 11/11/2011) is still broken. The quickest way to deal with this seems to be to shut down the pipe+ports+DPLL. Unfortunately doing this during the normal sanitization phase isn't quite soon enough as we already spew several WARNs about the bogus hardware state. But it's better than hanging the boot for a few dozen seconds. Since this is limited to a few old machines it doesn't seem entirely worthwile to try and rework the readout+sanitization code to handle it more gracefully. v2: Fix potential NULL deref (kbuild test robot) Constify has_bogus_dpll_config() Cc: stable@vger.kernel.org # v4.20+ Cc: Daniel Kamil Kozar <dkk089@gmail.com> Reported-by: Daniel Kamil Kozar <dkk089@gmail.com> Tested-by: Daniel Kamil Kozar <dkk089@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109245 Fixes: 516a49cc ("drm/i915: Fix assert_plane() warning on bootup with external display") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190111174950.10681-1-ville.syrjala@linux.intel.comReviewed-by: Mika Kahola <mika.kahola@intel.com>
-
Ville Syrjälä authored
Just like the frame counter, the pixel counter also reads zero all the time when the TV encoder is used. Fortunately the scanline counter still works sufficiently well so let's use that to correct the vblank timestamps. Otherwise the timestamps may en up out of whack, and since we use them to guesstimate the vblank counter value that may end up incorrect as well. Cc: Imre Deak <imre.deak@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125181931.19482-2-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
Ever since commit 204474a6 ("drm/i915: Pass down rc in intel_encoder->compute_config()") we're supposed to return an errno from .compute_config(). I failed to notice that when pushing the TV encoder fixes which were written before said commmit. Fix up the return value for the error case. Cc: Imre Deak <imre.deak@intel.com> Fixes: 690157f0 ("drm/i915/tv: Fix >1024 modes on gen3") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125181931.19482-1-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Chris Wilson authored
During igt, we ask to reset the device if any requests are still outstanding at the end of a test, as this quickly kills off any erroneous hanging request streams that may escape a test. However, since it may take the device a few milliseconds to flush itself after the end of a normal test, *cough* guc *cough*, we may accidentally tell the device to reset itself after it idles. If we wait a moment, our usual I915_IDLE_ENGINES_TIMEOUT of 200ms (seems a bit high, but still better than umpteen hangchecks!), we can differentiate better between a stuck engine and a healthy one, and so avoid prematurely forcing the reset and any extra complications that may entail. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128010245.20148-1-chris@chris-wilson.co.uk
-
- 26 Jan, 2019 1 commit
-
-
Nathan Chancellor authored
This warning is disabled by default in scripts/Makefile.extrawarn when W= is not provided but this Makefile adds -Wall after this warning is disabled so it shows up in the build when it shouldn't: In file included from drivers/gpu/drm/i915/intel_breadcrumbs.c:895: drivers/gpu/drm/i915/selftests/intel_breadcrumbs.c:350:34: error: variable 'wq' is uninitialized when used within its own initialization [-Werror,-Wuninitialized] DECLARE_WAIT_QUEUE_HEAD_ONSTACK(wq); ^~ ./include/linux/wait.h:74:63: note: expanded from macro 'DECLARE_WAIT_QUEUE_HEAD_ONSTACK' struct wait_queue_head name = __WAIT_QUEUE_HEAD_INIT_ONSTACK(name) ~~~~ ^~~~ ./include/linux/wait.h:72:33: note: expanded from macro '__WAIT_QUEUE_HEAD_INIT_ONSTACK' ({ init_waitqueue_head(&name); name; }) ^~~~ 1 error generated. Explicitly disable the warning like commit 46e20680 ("drm/i915: Disable some extra clang warnings"). Link: https://github.com/ClangBuiltLinux/linux/issues/220Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <nick.desaulniers@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190126071122.24557-1-natechancellor@gmail.com
-
- 25 Jan, 2019 27 commits
-
-
P Raviraj Sitaram authored
framebuffer for NV12 requires the pitch to the multiplier of 4, instead of the width. This patch corrects it. For instance, a 480p video, whose width and pitch are 854 and 896 respectively, is excluded for NV12 plane so far. Changes since v1: - Removed check for NV12 buffer dimensions since additional checks are done for viewport size in intel_sprite.c Signed-off-by: Dongseong Hwang <dongseong.hwang@intel.com> Signed-off-by: P Raviraj Sitaram <raviraj.p.sitaram@intel.com> Cc: Chandra Konduru <chandra.konduru@intel.com> Cc: Vidya Srinivas <vidya.srinivas@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1545208152-22658-1-git-send-email-raviraj.p.sitaram@intel.com
-
Ville Syrjälä authored
Rename some of the state variables in intel_plane_atomic_check_with_state() to make it less confusing. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190111170823.4441-2-ville.syrjala@linux.intel.comReviewed-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com>
-
Ville Syrjälä authored
Since gen3 can't handle >1024 wide sources with vertical scaling let's not advertize such modes in the mode list. Less tempetation to the user to try out things that won't work. v2: s/IS_GEN3(dev_priv/IS_GEN(dev_priv, 3)/ Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-17-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
On gen3 we must disable the TV encoder vertical filter for >1024 pixel wide sources. Once that's done all we can is try to center the image on the screen. Naturally the TV mode vertical resolution must be equal or larger than the user mode vertical resolution or else we'd have to cut off part of the user mode. And while we may not be able to respect the user's choice of top and bottom borders exactly (or we'd have to reject he mode most likely), we can try to maintain the relative sizes of the top and bottom border with respect to each orher. Additionally we must configure the pipe as interlaced if the TV mode is interlaced. v2: Make +intel_tv_connector_duplicate_state() static and drop the badly copy pasted kerneldoc s/IS_GEN3(dev_priv/IS_GEN(dev_priv, 3)/ Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-16-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
To make vblank timestamps work better with the TV encoder let's scale the pipe timings such that the relationship between the TV active and TV blanking periods is mirrored in the corresponding pipe timings. Note that in reality the pipe runs at a faster speed during the TV vblank, and correspondigly there are periods when the pipe is enitrely stopped. We pretend that this isn't the case and as such we incur some error in the vblank timestamps during the TV vblank. Further explanation of the issues in a big comment in the code. This makes the vblank timestamps good enough to make i965gm (which doesn't have a working frame counter with the TV encoder) report correct frame numbers. Previously you could get all kinds of nonsense which resulted in eg. glxgears reporting that it's running at twice the actual framerate in most cases. v2: s/IS_GEN4(dev_priv)/IS_GEN(dev_priv, 4)/ in the comment for consistency Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-15-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
Add the missing 1080p TV modes. On gen4 all of them work just fine, whereas on gen3 only the 30Hz mode actually works correctly. v2: s/IS_GEN3(dev_priv)/IS_GEN(dev_priv, 3)/ Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-14-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
Remove the silly reported_modes[] array. I suppse once upon a time this actually had something to do with modes we reported to userspace. Now it is just the placeholder for the mode we use for load detection. We don't need it even for that, and instead we can just rely on the fallback mode in intel_get_load_detect_pipe(). Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-13-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
The current code insists on picking a new TV mode when switching between component and non-component cables. That's super annoying. Let's just keep the current TV mode unless the new cable type actually disagrees with it. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-12-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
No point in storing the mode names in the array. drm_mode_set_name() will give us the same names without wasting space for these string constants. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-11-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
Rewrite the preferred mode selection to just check whether the TV modes is HD or SD. For SD TV modes we favor 480 line modes, for 720p we prefer 720 line modes, and for 1080i/p we prefer 1080 line modes. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-10-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
Just assign the margin values directly to xpos/ypos instead of first initializing to zero and then adding the values. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-8-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
'component_only' is a bool. Initialize it like a bool. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-7-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
Store the oversampling factor as a number in the TV modes. We shall want to arithmetic with this which is easier if it's a number we can use directly. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-6-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
The oversample clock is always supposed to be either 108 MHz or 148.5 MHz. Make it so. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-5-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
Fix the calculation of the vertical active period for interlaced TV modes. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181112170000.27531-4-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Ville Syrjälä authored
On i965gm the hardware frame counter does not work when the TV encoder is active. So let's not try to consult the hardware frame counter in that case. Instead we'll fall back to the timestamp based guesstimation method used on gen2. Note that the pipe timings generated by the TV encoder are also rather peculiar. Apparently the pipe wants to run at a much higher speed (related to the oversample clock somehow it seems) but during the vertical active period the TV encoder stalls the pipe every few lines to keep its speed in check. But once the vertical blanking period is reached the pipe gets to run at full speed. This means our vblank timestamp estimates are suspect. Fixing all that would require quite a bit more work. This simple fix at least avoids the nasty vblank timeouts that are happening currently. Curiously the frame counter works just fine on i945gm and gm45. I don't really understand what kind of mishap occurred with the hardware design on i965gm. Sadly I wasn't able to find any chicken bits etc. that would fix the frame counter :( v2: Move the zero vs. non-zero hw counter value handling into i915_get_vblank_counter() (Daniel) Use the per-crtc maximum exclusively, leaving the per-device maximum at zero v3: max_vblank_count not populated yet in intel_enable_pipe() use intel_crtc_max_vblank_count() instead Cc: stable@vger.kernel.org Cc: Daniel Vetter <daniel@ffwll.ch> Fixes: 51e31d49 ("drm/i915: Use generic vblank wait") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93782Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190122125149.GE5527@ideak-desk.fi.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>
-
Chris Wilson authored
Always perform the requested reset, even if we believe the engine is idle. Presumably there was a reason the caller wanted the reset, and in the near future we lose the easy tracking for whether the engine is idle. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125132230.22221-5-chris@chris-wilson.co.uk
-
Chris Wilson authored
Trim the struct_mutex hold and exclude the call to i915_gem_set_wedged() as a reminder that it must be callable without struct_mutex held. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125132230.22221-4-chris@chris-wilson.co.uk
-
Chris Wilson authored
Now that the submission backends are controlled via their own spinlocks, with a wave of a magic wand we can lift the struct_mutex requirement around GPU reset. That is we allow the submission frontend (userspace) to keep on submitting while we process the GPU reset as we can suspend the backend independently. The major change is around the backoff/handoff strategy for performing the reset. With no mutex deadlock, we no longer have to coordinate with any waiter, and just perform the reset immediately. Testcase: igt/gem_mmap_gtt/hang # regresses Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125132230.22221-3-chris@chris-wilson.co.uk
-
Chris Wilson authored
The guc (and huc) currently inexcruitably depend on struct_mutex for device reinitialisation from inside the reset, and indeed taking any mutex here is verboten (as we must be able to reset from underneath any of our mutexes). That makes recovering the guc unviable without, for example, reserving contiguous vma space and pages for it to use. The plan to re-enable global reset for the GuC centres around reusing the WOPM reserved space at the top of the aperture (that we know we can populate a contiguous range large enough to dma xfer the fw image). In the meantime, hopefully no one even notices as the device-reset is only used as a backup to the per-engine resets for handling GPU hangs. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Reviewed-by: John Harrison <John.C.Harrison@Intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125132230.22221-2-chris@chris-wilson.co.uk
-
Chris Wilson authored
In preparation for the next few commits, make resetting the GPU atomic. Currently, we have prepared gen6+ for atomic resetting of individual engines, but now there is a requirement to perform the whole device level reset (just the register poking) from inside an atomic context. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125132230.22221-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
Simplify by using sizeof(u32) to convert from the index inside the HWSP to the byte offset. This has the advantage of not only being shorter (and so not upsetting checkpatch!) but that it matches use where we are writing to byte addresses using other commands than MI_STORE_DWORD_IMM. v2: Drop the now superfluous MI_STORE_DWORD_INDEX_SHIFT, it appears to be a local invention so keeping it after the final use does not help to clarify the GPU instruction. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125120005.25191-2-chris@chris-wilson.co.uk
-
Chris Wilson authored
Now that we know we measure the size of the engine->emit_breadcrumb() correctly, we can remove the previous manual counting. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125120005.25191-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
Instead of tediously and fragilely counting up the number of dwords required to emit the breadcrumb to seal a request, fake a request and measure it automatically once during engine setup. The downside is that this requires a fair amount of mocking to create a proper breadcrumb. Still, should be less error prone in future as the breadcrumb size fluctuates! Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125100520.20163-1-chris@chris-wilson.co.uk
-
Tvrtko Ursulin authored
Configuring RPCS in context image just before pin is sufficient and will come extra handy in one of the following patches. v2: * Split image setup a bit differently. (Chris Wilson) v3: * Update context image after reset as well - otherwise the application of pinned default state clears the RPCS. v4: * Use local variable throughout the function. (Chris Wilson) Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125023005.1007-1-chris@chris-wilson.co.uk
-
Tomasz Lis authored
The table has been unified across OSes to minimize virtualization overhead. The MOCS table is now published as part of bspec, and versioned. Entries are supposed to never be modified, but new ones can be added. Adding entries increases table version. The patch includes version 1 entries. Meaning of each entry is now explained in bspec, and user mode clients are expected to know what each entry means. The 3 entries used for previous platforms are still compatible with their legacy definitions, but that is not guaranteed to be true for future platforms. v2: Fixed SCC values, improved commit comment (Daniele) v3: Improved MOCS table comment (Daniele) v4: Moved new entries below gen9 ones. Put common entries into definition to be used in multiple arrays. (Lucas) v5: Made defines for or-ing flags. Renamed macros from MOCS_TABLE to MOCS_ENTRIES. Switched LE_CoS to upper case. (Joonas) v6: Removed definitions of reserved entries. (Michal) Increased limit of entries sent to the hardware on gen11+. v7: Simplify table as done for previou gens (Lucas) v8: Rebase on cached number of entries per-platform and use new MOCS_ENTRY() macro (Lucas) v9: Update comment (from Tomasz) BSpec: 34007 BSpec: 560 Signed-off-by: Tomasz Lis <tomasz.lis@intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190124000604.18861-8-lucas.demarchi@intel.com
-
Lucas De Marchi authored
Instead of checking the gen number every time we need to know the max number of entries, just save it into the table struct so we don't need extra branches throughout the code. This will be useful for Ice Lake that has 64 rather than 62 defined entries. Ice Lake changes will be added in a follow up. v2: make size and n_entries `unsigned int` and introduce changes as a pre-work for the Ice Lake changes (Tvrtko) Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Tomasz Lis <tomasz.lis@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190124000604.18861-7-lucas.demarchi@intel.com
-