drivers/nfc/st21nfca/i2c.c does not use any miscdevice, so this patch
remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

drivers/nfc/pn544/i2c.c does not use any miscdevice, so this
patch remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

drivers/nfc/nxp-nci/i2c.c does not use any miscdevice, so this patch
remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Directly including access_ok.h can result in the following compile errors
if an architecture such as ia64 does not support direct unaligned accesses.

include/linux/unaligned/access_ok.h:7:19: error:
	redefinition of 'get_unaligned_le16'
include/linux/unaligned/le_struct.h:6:19: note:
	previous definition of 'get_unaligned_le16' was here
include/linux/unaligned/access_ok.h:12:19: error:
	redefinition of 'get_unaligned_le32'
include/linux/unaligned/le_struct.h:11:19: note:
	previous definition of 'get_unaligned_le32' was here

Include asm/unaligned.h instead and let the architecture decide which
access functions to use.

Cc: Clément Perrochaud <clement.perrochaud@effinnov.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Including linux/unaligned/access_ok.h causes the allmodconfig build on
ia64 (and maybe others) to fail with the following warnings:

include/linux/unaligned/access_ok.h:7:19: error: redefinition of 'get_unaligned_le16'
include/linux/unaligned/access_ok.h:12:19: error: redefinition of 'get_unaligned_le32'
include/linux/unaligned/access_ok.h:17:19: error: redefinition of 'get_unaligned_le64'
include/linux/unaligned/access_ok.h:22:19: error: redefinition of 'get_unaligned_be16'
include/linux/unaligned/access_ok.h:27:19: error: redefinition of 'get_unaligned_be32'
include/linux/unaligned/access_ok.h:32:19: error: redefinition of 'get_unaligned_be64'
include/linux/unaligned/access_ok.h:37:20: error: redefinition of 'put_unaligned_le16'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_le32'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_le64'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_be16'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_be32'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_be64'

Fix these by including asm/unaligned.h instead and leave it up to the
architecture to decide how to implement unaligned accesses.

Fixes: 3194c687 ("NFC: nfcmrvl: add firmware download support")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Link: https://lkml.org/lkml/2016/10/22/247
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Drop duplicate header gpio.h from nfcmrvl/spi.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

It appears that TI WiLink devices including NFC (WL185x/WL189x) never
shipped. The only information I found were announcements in Feb
2012 about the parts. There's been no activity on this driver besided
common changes since initially added in Jan 2012. There's also no in
users that instantiate the platform device (nor DT bindings).

This is a first step in removing TI ST (shared transport) driver in
favor of extending the BT hci_ll driver to support WL183x chips.

Cc: Ilan Elias <ilane@ti.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If port100_send_ack() was called twice or more, it has race to hangup.

  port100_send_ack()          port100_send_ack()
    init_completion()
    [...]
    dev->cmd_cancel = true
                                /* this removes previous from completion */
                                init_completion()
				[...]
                                dev->cmd_cancel = true
                                wait_for_completion()
    /* never be waked up */
    wait_for_completion()

Like above race, this code is not assuming port100_send_ack() is
called twice or more.

To fix, this checks dev->cmd_cancel to know if prior cancel is
in-flight or not. And never be remove prior task from completion by
using reinit_completion(), so this guarantees to be waked up properly
soon or later.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If sent packet size is wMaxPacketSize boundary, this device doesn't
answer. To fix this, we have to send zero-length packet in usb spec.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Now, NFC_EVENT_DEVICE_ADDED doesn't send NFC_ATTR_RF_MODE. But
NFC_CMD_GET_DEVICE send.

To get NFC_ATTR_RF_MODE, we have to call NFC_CMD_GET_DEVICE just for
NFC_ATTR_RF_MODE when get NFC_EVENT_DEVICE_ADDED.

This fixes those inconsistent.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Alexei Starovoitov says:

====================
bpf: program testing framework

Development and testing of networking bpf programs is quite cumbersome.
Especially tricky are XDP programs that attach to real netdevices and
program development feels like working on the car engine while
the car is in motion.
Another problem is ongoing changes to upstream llvm core
that can introduce an optimization that verifier will not
recognize. llvm bpf backend tests have no ability to run the programs.
To improve this situation introduce BPF_PROG_TEST_RUN command
to test and performance benchmark bpf programs.
It achieves several goals:
- development of xdp and skb based bpf programs can be done
in a canned environment with unit tests
- program performance optimizations can be benchmarked outside of
networking core (without driver and skb costs)
- continuous testing of upstream changes is finally practical

Patches 4,5,6 add C based test cases of various complexity
to cover some sched_cls and xdp features. More tests will
be added in the future. The tests were run on centos7 only.

For now the framework supports only skb and xdp programs. In the future
it can be extended to socket_filter and tracing program types.

More details are in individual patches.

v1->v2:
- rename bpf_program_test_run->bpf_prog_test_run
- add missing #include <linux/bpf.h> since libbpf.h shouldn't depend
on prior includes
- reordered patches 3 and 4 to keep bisect clean
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

this l4lb demo is a comprehensive test case for LLVM codegen and
kernel verifier. It's using fully inlined jhash(), complex packet
parsing and multiple map lookups of different types to stress
llvm and verifier.
The map sizes, map population and test vectors are artificial to
exercise different paths through the bpf program.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add C test for xdp_adjust_head(), packet rewrite and map lookups
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add simple C test case for llvm and verifier range check fix from
commit b1977682 ("bpf: improve verifier packet range checks")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

expose bpf_program__set_type() to set program type
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add support for BPF_PROG_TEST_RUN command to libbpf.a
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

development and testing of networking bpf programs is quite cumbersome.
Despite availability of user space bpf interpreters the kernel is
the ultimate authority and execution environment.
Current test frameworks for TC include creation of netns, veth,
qdiscs and use of various packet generators just to test functionality
of a bpf program. XDP testing is even more complicated, since
qemu needs to be started with gro/gso disabled and precise queue
configuration, transferring of xdp program from host into guest,
attaching to virtio/eth0 and generating traffic from the host
while capturing the results from the guest.

Moreover analyzing performance bottlenecks in XDP program is
impossible in virtio environment, since cost of running the program
is tiny comparing to the overhead of virtio packet processing,
so performance testing can only be done on physical nic
with another server generating traffic.

Furthermore ongoing changes to user space control plane of production
applications cannot be run on the test servers leaving bpf programs
stubbed out for testing.

Last but not least, the upstream llvm changes are validated by the bpf
backend testsuite which has no ability to test the code generated.

To improve this situation introduce BPF_PROG_TEST_RUN command
to test and performance benchmark bpf programs.

Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for a DSA mock-up driver which essentially does
the following:

- registers/unregisters 4 fixed PHYs to the slave network devices
- uses eth0 (configurable) as the master netdev
- registers the switch as a fixed MDIO device against the fixed MDIO bus
  at address 31
- includes dynamic debug prints for dsa_switch_ops functions that can be
  enabled to get call traces

This is a good way to test modular builds as well as exercise the DSA
APIs without requiring access to real hardware. This does not test the
data-path, although this could be added later on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: program cross-chip bridging

The purpose of this patch series is to bring hardware cross-chip
bridging configuration to the DSA layer and the mv88e6xxx DSA driver.

Most recent Marvell switch chips have a Cross-chip Port Based VLAN Table
(PVT) used to restrict to which internal destination port an arbitrary
external source port is allowed to egress frames to.

The current behavior of the mv88e6xxx driver is to program this table
table with all ones, allowing any external ports to egress frames on any
internal ports. This means that carefully crafted Ethernet frames can
potentially bypass the user bridging configuration.

Patches 1 to 7 prepare the setup of this table and factorize the common
bits of both in-chip and cross-chip Marvell bridging code.

Patch 8 adds new optional cross-chip bridging operations to DSA switch.

Patch 9 switches the current behavior to program the table according to
the user bridging configuration when (cross-chip) ports get (un)bridged.

On a ZII Rev B board, bridging together the 3 user ports of both 88E6352
will result in the following PVTs on respectively switch 0 and switch 1:

    External   Internal Ports
    Dev Port   0  1  2  3  4  5  6

     1    0    *  *  *  -  -  *  *
     1    1    *  *  *  -  -  *  *
     1    2    *  *  *  -  -  *  *
     1    3    -  -  -  -  -  *  *
     1    4    -  -  -  -  -  *  *
     1    5    *  *  *  *  *  *  *
     1    6    *  *  *  *  *  *  *

     0    0    *  *  *  -  -  *  *
     0    1    *  *  *  -  -  *  *
     0    2    *  *  *  -  -  *  *
     0    3    -  -  -  -  -  *  *
     0    4    -  -  -  -  -  *  *
     0    5    *  *  *  *  *  *  *
     0    6    *  *  *  *  *  *  *

Changes since v2:
  - Define MV88E6XXX_MAX_PVT_SWITCHES and MV88E6XXX_MAX_PVT_PORTS
  - use mv88e6xxx_g2_misc_4_bit_port instead of the 5-bit variant
  - add Andrew's tags and reword commit 6/9
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the DSA cross-chip bridging operations by remapping the local
ports an external source port can egress frames to, when this cross-chip
port joins or leaves a bridge.

The PVT is no longer configured with all ones allowing any external
frame to egress any local port. Only DSA and CPU ports, as well as
bridge group members, can egress frames on local ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce crosschip_bridge_{join,leave} operations in the dsa_switch_ops
structure, which can be used by switches supporting interconnection.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a local port of a switch chip becomes a member of a bridge group,
we need to reprogram the Cross-chip Port Based VLAN Table (PVT) to allow
existing cross-chip bridge members to egress frames on the new ports.

There is no functional changes yet, since the PVT is still programmed
with all ones, allowing any external port to egress frames locally.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factorize the code in the DSA port_bridge_{join,leave} routines used to
program the port VLAN map of all local ports of a given bridge group.

At the same time shorten the _mv88e6xxx_port_based_vlan_map to get rid
of the old underscore prefix naming convention.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

All ports -- internal and external, for chips featuring a PVT -- have a
mask restricting to which internal ports a frame is allowed to egress.

Now that DSA exposes the number of ports and their bridge devices, it is
possible to extract the code generating the VLAN map and make it generic
so that it can be shared later with the cross-chip bridging code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code allocates DSA_MAX_PORTS ports for a Marvell dsa_switch
structure. Provide the exact number of ports so the corresponding
ds->num_ports is accurate.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Cross-chip Port Based VLAN Table (PVT) is currently initialized with
all ones, allowing any external ports to egress frames on local ports.

This commit implements the PVT access functions and programs the PVT
with all ones for the local switch ports only, instead of using the Init
operation. The current behavior is unchanged for the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Cross-chip Port Based VLAN Table (PVT) supports two indexing modes,
one using 5-bit for device and 4-bit for port, the other using 4-bit for
device and 5-bit for port, configured via the Global 2 Misc register.

Only 4 bits for the source port are needed when interconnecting 88E6xxx
switch devices since they all support less than 16 physical ports. The
full 5 bits are needed when interconnecting a device with 98DXxxx switch
devices since they support more than 16 physical ports.

Add a mv88e6xxx_pvt_setup helper to set the 4-bit port PVT mode, which
will be extended later to also initialize the PVT content.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not all Marvell switch chips feature a Cross-chip Port VLAN Table (PVT).

Chips with a PVT use the same implementation, so a new mv88e6xxx_ops
member won't be necessary yet. Add a "pvt" boolean member to the
mv88e6xxx_info structure and kill the obsolete MV88E6XXX_FLAGS_PVT flag.

Add a mv88e6xxx_has_pvt helper to wrap future checks of that condition.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AVOIDBLOCK flag determines the Tx confirmation queues processing
to be redirected to any available CPU when the current one is slow
in processing them. This may result in a higher Tx confirmation
interrupt count but may reduce pressure on a certain CPU that with
the previous setting would process all Tx confirmation frames.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accept the internal delay RGMII variants.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan dev currently ignores lowerdev's gso_max_size, which adversely
affects TSO performance of liquidio if it's the lowerdev.  Egress TCP
packets' skb->len often exceed liquidio's advertised gso_max_size.  This
may happen on other NIC drivers.

Fix it by assigning lowerdev's gso_max_size to that of vxlan dev.  Might as
well do likewise for gso_max_segs.

Single flow TSO throughput of liquidio as lowerdev (using iperf3):

    Before the patch:    139 Mbps
    After the patch :   8.68 Gbps
    Percent increase:  6,144 %
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_recv_ts_and_drops() unconditionally set sk->sk_stamp for
every packet, even if the SOCK_TIMESTAMP flag is not set in the
related socket.
If selinux is enabled, this cause a cache miss for every packet
since sk->sk_stamp and sk->sk_security share the same cacheline.
With this change sk_stamp is set only if the SOCK_TIMESTAMP
flag is set, and is cleared for the first packet, so that the user
perceived behavior is unchanged.

This gives up to 5% speed-up under udp-flood with small packets.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nathan Fontenot says:

====================
ibmvnic: Cleanup resource handling

In order to better manage the resources of the ibmvnic driver, this set of
patches creates a set of initialization and release routines for the
drivers resources. Additionally, some patches do some re-naming of the
affected routines so that there is a common naming scheme in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that ibmvnic_release_resources will clean up all of our resources
properly, even if they were not allocated, we can just call this
for failues in ibmvnic_open.

This patch also moves the ibmvnic_release_resources() routine up
in the file to avoid creating a forward declaration ad re-names it to
drop the ibmvnic prefix.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create an initialization and a release routine for the stats token used by
the ibmvnic driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Keeping two routines for releasing sub crqs, one for when irqs are not
initialized and one for when they are, is a bit of overkill. Merge the
two routines to a common release routine that will check for an irq
and release it if needed.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the initialization and the release of the rx pool to their own
routines, and update them to do validation.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the initialization and the release of the tx pool to their own routines,
and update them to do validation. This also adds validation to the release
of the long term buffer.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the handling of initialization and releasing the bounce buffer to their
own init and release routines.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>