Pull powerpc fixes from Michael Ellerman:
 - Handle RTAS delay requests in configure_bridge from Russell Currey
 - Refactor the configure_bridge RTAS tokens from Russell Currey
 - Fix definition of SIAR and SDAR registers from Thomas Huth
 - Use privileged SPR number for MMCR2 from Thomas Huth
 - Update LPCR only if it is powernv from Aneesh Kumar K.V
 - Fix the reference bit update when handling hash fault from Aneesh
   Kumar K.V
 - Add missing tlb flush from Aneesh Kumar K.V
 - Add POWER8NVL support to ibm,client-architecture-support call from
   Thomas Huth

* tag 'powerpc-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: Add POWER8NVL support to ibm,client-architecture-support call
  powerpc/mm/radix: Add missing tlb flush
  powerpc/mm/hash: Fix the reference bit update when handling hash fault
  powerpc/mm/radix: Update LPCR only if it is powernv
  powerpc: Use privileged SPR number for MMCR2
  powerpc: Fix definition of SIAR and SDAR registers
  powerpc/pseries/eeh: Refactor the configure_bridge RTAS tokens
  powerpc/pseries/eeh: Handle RTAS delay requests in configure_bridge

Pull KVM fixes from Radim Krčmář:
 "ARM:
   - two fixes for 4.6 vgic [Christoffer] (cc stable)

   - six fixes for 4.7 vgic [Marc]

  x86:
   - six fixes from syzkaller reports [Paolo] (two of them cc stable)

   - allow OS X to boot [Dmitry]

   - don't trust compilers [Nadav]"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix OOPS after invalid KVM_SET_DEBUGREGS
  KVM: x86: avoid vmalloc(0) in the KVM_SET_CPUID
  KVM: irqfd: fix NULL pointer dereference in kvm_irq_map_gsi
  KVM: fail KVM_SET_VCPU_EVENTS with invalid exception number
  KVM: x86: avoid vmalloc(0) in the KVM_SET_CPUID
  kvm: x86: avoid warning on repeated KVM_SET_TSS_ADDR
  KVM: Handle MSR_IA32_PERF_CTL
  KVM: x86: avoid write-tearing of TDP
  KVM: arm/arm64: vgic-new: Removel harmful BUG_ON
  arm64: KVM: vgic-v3: Relax synchronization when SRE==1
  arm64: KVM: vgic-v3: Prevent the guest from messing with ICC_SRE_EL1
  arm64: KVM: Make ICC_SRE_EL1 access return the configured SRE value
  KVM: arm/arm64: vgic-v3: Always resample level interrupts
  KVM: arm/arm64: vgic-v2: Always resample level interrupts
  KVM: arm/arm64: vgic-v3: Clear all dirty LRs
  KVM: arm/arm64: vgic-v2: Clear all dirty LRs

MOV to DR6 or DR7 causes a #GP if an attempt is made to write a 1 to
any of bits 63:32.  However, this is not detected at KVM_SET_DEBUGREGS
time, and the next KVM_RUN oopses:

   general protection fault: 0000 [#1] SMP
   CPU: 2 PID: 14987 Comm: a.out Not tainted 4.4.9-300.fc23.x86_64 #1
   Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
   [...]
   Call Trace:
    [<ffffffffa072c93d>] kvm_arch_vcpu_ioctl_run+0x141d/0x14e0 [kvm]
    [<ffffffffa071405d>] kvm_vcpu_ioctl+0x33d/0x620 [kvm]
    [<ffffffff81241648>] do_vfs_ioctl+0x298/0x480
    [<ffffffff812418a9>] SyS_ioctl+0x79/0x90
    [<ffffffff817a0f2e>] entry_SYSCALL_64_fastpath+0x12/0x71
   Code: 55 83 ff 07 48 89 e5 77 27 89 ff ff 24 fd 90 87 80 81 0f 23 fe 5d c3 0f 23 c6 5d c3 0f 23 ce 5d c3 0f 23 d6 5d c3 0f 23 de 5d c3 <0f> 23 f6 5d c3 0f 0b 66 66 66 66 66 2e 0f 1f 84 00 00 00 00 00
   RIP  [<ffffffff810639eb>] native_set_debugreg+0x2b/0x40
    RSP <ffff88005836bd50>

Testcase (beautified/reduced from syzkaller output):

    #include <unistd.h>
    #include <sys/syscall.h>
    #include <string.h>
    #include <stdint.h>
    #include <linux/kvm.h>
    #include <fcntl.h>
    #include <sys/ioctl.h>

    long r[8];

    int main()
    {
        struct kvm_debugregs dr = { 0 };

        r[2] = open("/dev/kvm", O_RDONLY);
        r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
        r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7);

        memcpy(&dr,
               "\x5d\x6a\x6b\xe8\x57\x3b\x4b\x7e\xcf\x0d\xa1\x72"
               "\xa3\x4a\x29\x0c\xfc\x6d\x44\x00\xa7\x52\xc7\xd8"
               "\x00\xdb\x89\x9d\x78\xb5\x54\x6b\x6b\x13\x1c\xe9"
               "\x5e\xd3\x0e\x40\x6f\xb4\x66\xf7\x5b\xe3\x36\xcb",
               48);
        r[7] = ioctl(r[4], KVM_SET_DEBUGREGS, &dr);
        r[6] = ioctl(r[4], KVM_RUN, 0);
    }
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

This causes an ugly dmesg splat.  Beautified syzkaller testcase:

    #include <unistd.h>
    #include <sys/syscall.h>
    #include <sys/ioctl.h>
    #include <fcntl.h>
    #include <linux/kvm.h>

    long r[8];

    int main()
    {
        struct kvm_irq_routing ir = { 0 };
        r[2] = open("/dev/kvm", O_RDWR);
        r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
        r[4] = ioctl(r[3], KVM_SET_GSI_ROUTING, &ir);
        return 0;
    }
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

Found by syzkaller:

    BUG: unable to handle kernel NULL pointer dereference at 0000000000000120
    IP: [<ffffffffa0797202>] kvm_irq_map_gsi+0x12/0x90 [kvm]
    PGD 6f80b067 PUD b6535067 PMD 0
    Oops: 0000 [#1] SMP
    CPU: 3 PID: 4988 Comm: a.out Not tainted 4.4.9-300.fc23.x86_64 #1
    [...]
    Call Trace:
     [<ffffffffa0795f62>] irqfd_update+0x32/0xc0 [kvm]
     [<ffffffffa0796c7c>] kvm_irqfd+0x3dc/0x5b0 [kvm]
     [<ffffffffa07943f4>] kvm_vm_ioctl+0x164/0x6f0 [kvm]
     [<ffffffff81241648>] do_vfs_ioctl+0x298/0x480
     [<ffffffff812418a9>] SyS_ioctl+0x79/0x90
     [<ffffffff817a1062>] tracesys_phase2+0x84/0x89
    Code: b5 71 a7 e0 5b 41 5c 41 5d 5d f3 c3 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 8b 8f 10 2e 00 00 31 c0 48 89 e5 <39> 91 20 01 00 00 76 6a 48 63 d2 48 8b 94 d1 28 01 00 00 48 85
    RIP  [<ffffffffa0797202>] kvm_irq_map_gsi+0x12/0x90 [kvm]
     RSP <ffff8800926cbca8>
    CR2: 0000000000000120

Testcase:

    #include <unistd.h>
    #include <sys/syscall.h>
    #include <string.h>
    #include <stdint.h>
    #include <linux/kvm.h>
    #include <fcntl.h>
    #include <sys/ioctl.h>

    long r[26];

    int main()
    {
        memset(r, -1, sizeof(r));
        r[2] = open("/dev/kvm", 0);
        r[3] = ioctl(r[2], KVM_CREATE_VM, 0);

        struct kvm_irqfd ifd;
        ifd.fd = syscall(SYS_eventfd2, 5, 0);
        ifd.gsi = 3;
        ifd.flags = 2;
        ifd.resamplefd = ifd.fd;
        r[25] = ioctl(r[3], KVM_IRQFD, &ifd);
        return 0;
    }
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

This cannot be returned by KVM_GET_VCPU_EVENTS, so it is okay to return
EINVAL.  It causes a WARN from exception_type:

    WARNING: CPU: 3 PID: 16732 at arch/x86/kvm/x86.c:345 exception_type+0x49/0x50 [kvm]()
    CPU: 3 PID: 16732 Comm: a.out Tainted: G        W       4.4.6-300.fc23.x86_64 #1
    Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
     0000000000000286 000000006308a48b ffff8800bec7fcf8 ffffffff813b542e
     0000000000000000 ffffffffa0966496 ffff8800bec7fd30 ffffffff810a40f2
     ffff8800552a8000 0000000000000000 00000000002c267c 0000000000000001
    Call Trace:
     [<ffffffff813b542e>] dump_stack+0x63/0x85
     [<ffffffff810a40f2>] warn_slowpath_common+0x82/0xc0
     [<ffffffff810a423a>] warn_slowpath_null+0x1a/0x20
     [<ffffffffa0924809>] exception_type+0x49/0x50 [kvm]
     [<ffffffffa0934622>] kvm_arch_vcpu_ioctl_run+0x10a2/0x14e0 [kvm]
     [<ffffffffa091c04d>] kvm_vcpu_ioctl+0x33d/0x620 [kvm]
     [<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
     [<ffffffff812414a9>] SyS_ioctl+0x79/0x90
     [<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71
    ---[ end trace b1a0391266848f50 ]---

Testcase (beautified/reduced from syzkaller output):

    #include <unistd.h>
    #include <sys/syscall.h>
    #include <string.h>
    #include <stdint.h>
    #include <fcntl.h>
    #include <sys/ioctl.h>
    #include <linux/kvm.h>

    long r[31];

    int main()
    {
        memset(r, -1, sizeof(r));
        r[2] = open("/dev/kvm", O_RDONLY);
        r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
        r[7] = ioctl(r[3], KVM_CREATE_VCPU, 0);

        struct kvm_vcpu_events ve = {
                .exception.injected = 1,
                .exception.nr = 0xd4
        };
        r[27] = ioctl(r[7], KVM_SET_VCPU_EVENTS, &ve);
        r[30] = ioctl(r[7], KVM_RUN, 0);
        return 0;
    }
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

This causes an ugly dmesg splat.  Beautified syzkaller testcase:

    #include <unistd.h>
    #include <sys/syscall.h>
    #include <sys/ioctl.h>
    #include <fcntl.h>
    #include <linux/kvm.h>

    long r[8];

    int main()
    {
        struct kvm_cpuid2 c = { 0 };
        r[2] = open("/dev/kvm", O_RDWR);
        r[3] = ioctl(r[2], KVM_CREATE_VM, 0);
        r[4] = ioctl(r[3], KVM_CREATE_VCPU, 0x8);
        r[7] = ioctl(r[4], KVM_SET_CPUID, &c);
        return 0;
    }
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

Found by syzkaller:

    WARNING: CPU: 3 PID: 15175 at arch/x86/kvm/x86.c:7705 __x86_set_memory_region+0x1dc/0x1f0 [kvm]()
    CPU: 3 PID: 15175 Comm: a.out Tainted: G        W       4.4.6-300.fc23.x86_64 #1
    Hardware name: LENOVO 2325F51/2325F51, BIOS G2ET32WW (1.12 ) 05/30/2012
     0000000000000286 00000000950899a7 ffff88011ab3fbf0 ffffffff813b542e
     0000000000000000 ffffffffa0966496 ffff88011ab3fc28 ffffffff810a40f2
     00000000000001fd 0000000000003000 ffff88014fc50000 0000000000000000
    Call Trace:
     [<ffffffff813b542e>] dump_stack+0x63/0x85
     [<ffffffff810a40f2>] warn_slowpath_common+0x82/0xc0
     [<ffffffff810a423a>] warn_slowpath_null+0x1a/0x20
     [<ffffffffa09251cc>] __x86_set_memory_region+0x1dc/0x1f0 [kvm]
     [<ffffffffa092521b>] x86_set_memory_region+0x3b/0x60 [kvm]
     [<ffffffffa09bb61c>] vmx_set_tss_addr+0x3c/0x150 [kvm_intel]
     [<ffffffffa092f4d4>] kvm_arch_vm_ioctl+0x654/0xbc0 [kvm]
     [<ffffffffa091d31a>] kvm_vm_ioctl+0x9a/0x6f0 [kvm]
     [<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
     [<ffffffff812414a9>] SyS_ioctl+0x79/0x90
     [<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71

Testcase:

    #include <unistd.h>
    #include <sys/ioctl.h>
    #include <fcntl.h>
    #include <string.h>
    #include <linux/kvm.h>

    long r[8];

    int main()
    {
        memset(r, -1, sizeof(r));
	r[2] = open("/dev/kvm", O_RDONLY|O_TRUNC);
        r[3] = ioctl(r[2], KVM_CREATE_VM, 0x0ul);
        r[5] = ioctl(r[3], KVM_SET_TSS_ADDR, 0x20000000ul);
        r[7] = ioctl(r[3], KVM_SET_TSS_ADDR, 0x20000000ul);
        return 0;
    }
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

Intel CPUs having Turbo Boost feature implement an MSR to provide a
control interface via rdmsr/wrmsr instructions. One could detect the
presence of this feature by issuing one of these instructions and
handling the #GP exception which is generated in case the referenced MSR
is not implemented by the CPU.

KVM's vCPU model behaves exactly as a real CPU in this case by injecting
a fault when MSR_IA32_PERF_CTL is called (which KVM does not support).
However, some operating systems use this register during an early boot
stage in which their kernel is not capable of handling #GP correctly,
causing #DP and finally a triple fault effectively resetting the vCPU.

This patch implements a dummy handler for MSR_IA32_PERF_CTL to avoid the
crashes.
Signed-off-by: Dmitry Bilunov <kmeaw@yandex-team.ru>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

In theory, nothing prevents the compiler from write-tearing PTEs, or
split PTE writes. These partially-modified PTEs can be fetched by other
cores and cause mayhem. I have not really encountered such case in
real-life, but it does seem possible.

For example, the compiler may try to do something creative for
kvm_set_pte_rmapp() and perform multiple writes to the PTE.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

KVM/ARM Fixes for v4.7-rc2

Fixes for the vgic, 2 of the patches address a bug introduced in v4.6
while the rest are for the new vgic.

When changing the active bit from an MMIO trap, we decide to
explode if the intid is that of a private interrupt.

This flawed logic comes from the fact that we were assuming that
kvm_vcpu_kick() as called by kvm_arm_halt_vcpu() would not return before
the called vcpu responded, but this is not the case, so we need to
perform this wait even for private interrupts.

Dropping the BUG_ON seems like the right thing to do.

 [ Commit message tweaked by Christoffer ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Pull pin control fixes from Linus Walleij:
 "Here are three pin control fixes for v4.7.  Not much, and just driver
  fixes:

   - add device tree matches to MAINTAINERS

   - inversion bug in the Nomadik driver

   - dual edge handling bug in the mediatek driver"

* tag 'pinctrl-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: mediatek: fix dual-edge code defect
  MAINTAINERS: Add file patterns for pinctrl device tree bindings
  pinctrl: nomadik: fix inversion of gpio direction

Pull dma-buf updates from Sumit Semwal:

 - use of vma_pages instead of explicit computation

 - DocBook and headerdoc updates for dma-buf

* tag 'dma-buf-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
  dma-buf: use vma_pages()
  fence: add missing descriptions for fence
  doc: update/fixup dma-buf related DocBook
  reservation: add headerdoc comments
  dma-buf: headerdoc fixes

Pull networking fixes from David Miller:

 1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.

 2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
    properly.  From Ezequiel Garcia.

 3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.

 4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.

 5) Fix deadlock on team->lock when propagating features, from Ivan
    Vecera.

 6) Work around buffer offset hw bug in alx chips, from Feng Tang.

 7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
    Long.

 8) Various statistics bug fixes in mlx4 from Eric Dumazet.

 9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.

10) All of l2tp was namespace aware, but the ipv6 support code was not
    doing so.  From Shmulik Ladkani.

11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.

12) Propagate MAC changes properly through VLAN devices, from Mike
    Manning.

13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
  sfc: Track RPS flow IDs per channel instead of per function
  usbnet: smsc95xx: fix link detection for disabled autonegotiation
  virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
  bnx2x: avoid leaking memory on bnx2x_init_one() failures
  fou: fix IPv6 Kconfig options
  openvswitch: update checksum in {push,pop}_mpls
  sctp: sctp_diag should dump sctp socket type
  net: fec: update dirty_tx even if no skb
  vlan: Propagate MAC address to VLANs
  atm: iphase: off by one in rx_pkt()
  atm: firestream: add more reserved strings
  vxlan: Accept user specified MTU value when create new vxlan link
  net: pktgen: Call destroy_hrtimer_on_stack()
  timer: Export destroy_hrtimer_on_stack()
  net: l2tp: Make l2tp_ip6 namespace aware
  Documentation: ip-sysctl.txt: clarify secure_redirects
  sfc: use flow dissector helpers for aRFS
  ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
  net: nps_enet: Disable interrupts before napi reschedule
  net/lapb: tuse %*ph to dump buffers
  ...

Pull sparc fixes from David Miller:
 "sparc64 mmu context allocation and trap return bug fixes"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix return from trap window fill crashes.
  sparc: Harden signal return frame checks.
  sparc64: Take ctx_alloc_lock properly in hugetlb_setup().

If we do not provide the PVR for POWER8NVL, a guest on this system
currently ends up in PowerISA 2.06 compatibility mode on KVM, since QEMU
does not provide a generic PowerISA 2.07 mode yet. So some new
instructions from POWER8 (like "mtvsrd") get disabled for the guest,
resulting in crashes when using code compiled explicitly for
POWER8 (e.g. with the "-mcpu=power8" option of GCC).

Fixes: ddee09c0 ("powerpc: Add PVR for POWER8NVL processor")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This should not have any impact on hash, because hash does tlb
invalidate with every pte update and we don't implement
flush_tlb_* functions for hash. With radix we should make an explicit
call to flush tlb outside pte update.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When we converted the asm routines to C functions, we missed updating
HPTE_R_R based on _PAGE_ACCESSED. ASM code used to copy over the lower
bits from pte via.

andi.	r3,r30,0x1fe		/* Get basic set of flags */

We also update the code such that we won't update the Change bit ('C'
bit) always. This was added by commit c5cf0e30 ("powerpc: Fix
buglet with MMU hash management").

With hash64, we need to make sure that hardware doesn't do a pte update
directly. This is because we do end up with entries in TLB with no hash
page table entry. This happens because when we find a hash bucket full,
we "evict" a more/less random entry from it. When we do that we don't
invalidate the TLB (hpte_remove) because we assume the old translation
is still technically "valid". For more info look at commit
0608d692("powerpc/mm: Always invalidate tlb on hpte invalidate and
update").

Thus it's critical that valid hash PTEs always have reference bit set
and writeable ones have change bit set. We do this by hashing a
non-dirty linux PTE as read-only and always setting _PAGE_ACCESSED (and
thus R) when hashing anything else in. Any attempt by Linux at clearing
those bits also removes the corresponding hash entry.

Commit 5cf0e30bf3d8 did that for 'C' bit by enabling 'C' bit always.
We don't really need to do that because we never map a RW pte entry
without setting 'C' bit. On READ fault on a RW pte entry, we still map
it READ only, hence a store update in the page will still cause a hash
pte fault.

This patch reverts the part of commit c5cf0e30 ("[PATCH] powerpc:
Fix buglet with MMU hash management") and retain the updatepp part.

- If we hit the updatepp path on native, the old code without that
  commit, would fail to set C bcause native_hpte_updatepp()
  was implemented to filter the same bits as H_PROTECT and not let C
  through thus we would "upgrade" a RO HPTE to RW without setting C
  thus causing the bug. So the real fix in that commit was the change
  to native_hpte_updatepp

Fixes: 89ff7250 ("powerpc/mm: Convert __hash_page_64K to C")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

LPCR cannot be updated when running in guest mode.

Fixes: 2bfd65e4 ("powerpc/mm/radix: Add radix callbacks for early init routines")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Otherwise we get confused when two flows on different channels get the
 same flow ID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To detect link status up/down for connections where autonegotiation is
explicitly disabled, we don't get an irq but need to poll the status
register for link up/down detection.
This patch adds a workqueue to poll for link status.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function virtnet_open() and virtnet_probe(), func try_fill_recv() may
be executed at the same time. VQ in virtqueue_add() has not been protected
well and BUG_ON will be triggered when virito_net.ko being removed.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x_init_bp() allocates memory with bnx2x_alloc_mem_bp() so if we
fail later in bnx2x_init_one() we need to free this memory
with bnx2x_free_mem_bp() to avoid leakages. E.g. I'm observing memory
leaks reported by kmemleak when a failure (unrelated) happens in
bnx2x_vfpf_acquire().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Kconfig options I added to work around broken compilation ended
up screwing up things more, as I used the wrong symbol to control
compilation of the file, resulting in IPv6 fou support to never be built
into the kernel.

Changing CONFIG_NET_FOU_IPV6_TUNNELS to CONFIG_IPV6_FOU fixes that
problem, I had renamed the symbol in one location but not the other,
and as the file is never being used by other kernel code, this did not
lead to a build failure that I would have caught.

After that fix, another issue with the same patch becomes obvious, as we
'select INET6_TUNNEL', which is related to IPV6_TUNNEL, but not the same,
and this can still cause the original build failure when IPV6_TUNNEL is
not built-in but IPV6_FOU is. The fix is equally trivial, we just need
to select the right symbol.

I have successfully build 350 randconfig kernels with this patch
and verified that the driver is now being built.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Fixes: fabb13db ("fou: add Kconfig options for IPv6 support")
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case of CHECKSUM_COMPLETE the skb checksum should be updated in
{push,pop}_mpls() as they the type in the ethernet header.

As suggested by Pravin Shelar.

Cc: Pravin Shelar <pshelar@nicira.com>
Fixes: 25cd9ba0 ("openvswitch: Add basic MPLS support to kernel")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now we cannot distinguish that one sk is a udp or sctp style when
we use ss to dump sctp_info. it's necessary to dump it as well.

For sctp_diag, ss support is not officially available, thus there
are no official users of this yet, so we can add this field in the
middle of sctp_info without breaking user API.

v1->v2:
  - move 'sctpi_s_type' field to the end of struct sctp_info, so
    that it won't cause incompatibility with applications already
    built.
  - add __reserved3 in sctp_info to make sure sctp_info is 8-byte
    alignment.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If dirty_tx isn't updated, then dma_unmap_single
can be called twice.

This fixes a
[   58.420980] ------------[ cut here ]------------
[   58.425667] WARNING: CPU: 0 PID: 377 at /home/schurig/d/mkarm/linux-4.5/lib/dma-debug.c:1096 check_unmap+0x9d0/0xab8()
[   58.436405] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=66 bytes]

encountered by Holger
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: <holgerschurig@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC address of the physical interface is only copied to the VLAN
when it is first created, resulting in an inconsistency after MAC
address changes of only newly created VLANs having an up-to-date MAC.

The VLANs should continue inheriting the MAC address of the physical
interface until the VLAN MAC address is explicitly set to any value.
This allows IPv6 EUI64 addresses for the VLAN to reflect any changes
to the MAC of the physical interface and thus for DAD to behave as
expected.
Signed-off-by: Mike Manning <mmanning@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The iadev->rx_open[] array holds "iadev->num_vc" pointers (this code
assumes that pointers are 32 bits).  So the > here should be >= or else
we could end up reading a garbage pointer from one element beyond the
end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This bug was there when the driver was first added in back in year 2000.
It causes a Smatch warning:

    drivers/atm/firestream.c:849 process_incoming()
    error: buffer overflow 'res_strings' 60 <= 63

There are supposed to be 64 entries in this array and the missing
strings are clearly in the 30 40 range.  I added them as reserved 37 to
reserved 40.  It's possible that strings are really supposed to be added
in the middle instead of at the end, but this approach is safe, in that
it fixes the bug and doesn't break anything that wasn't already broken.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When create a new vxlan link, example:
  ip link add vtap mtu 1440 type vxlan vni 1 dev eth0

The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.

This problem was introduced by commit 0dfbdf41 (vxlan: Factor out device
configuration).

Fixes: 0dfbdf41 (vxlan: Factor out device configuration)
Signed-off-by: Chen Haiquan <oc@yunify.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If CONFIG_DEBUG_OBJECTS_TIMERS=y, hrtimer_init_on_stack() requires
a matching call to destroy_hrtimer_on_stack() to clean up timer
debug objects.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

hrtimer_init_on_stack() needs a matching call to
destroy_hrtimer_on_stack(), so both need to be exported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace explicit computation of vma page count by a call to
vma_pages().
Also, include <linux/mm.h>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>

The members child_list and active_list were added to the fence struct
without descriptions for the Documentation. Adding these.

Fixes: b55b54b5 ("staging/android: remove struct sync_pt")
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>

Split out dma-buf related parts into their own section, add missing
files, and write a bit of overview about how it all fits together.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>

Pull s390 fixes from Martin Schwidefsky:
 "Three bugs fixes and an update for the default configuration"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: fix info leak in do_sigsegv
  s390/config: update default configuration
  s390/bpf: fix recache skb->data/hlen for skb_vlan_push/pop
  s390/bpf: reduce maximum program size to 64 KB

Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>

Apparently nobody noticed that dma-buf.h wasn't actually pulled into
docbook build.  And as a result the headerdoc comments bitrot a bit.
Add missing params/fields.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>