Syzbot reported a memory leak about skb:

unreferenced object 0xffff88810e144e00 (size 240):
  comm "syz-executor284", pid 3701, jiffies 4294952403 (age 12.620s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff83ab79a9>] __alloc_skb+0x1f9/0x270 net/core/skbuff.c:497
    [<ffffffff82a5cf64>] alloc_skb include/linux/skbuff.h:1267 [inline]
    [<ffffffff82a5cf64>] virtual_ncidev_write+0x24/0xe0 drivers/nfc/virtual_ncidev.c:116
    [<ffffffff815f6503>] do_loop_readv_writev fs/read_write.c:759 [inline]
    [<ffffffff815f6503>] do_loop_readv_writev fs/read_write.c:743 [inline]
    [<ffffffff815f6503>] do_iter_write+0x253/0x300 fs/read_write.c:863
    [<ffffffff815f66ed>] vfs_writev+0xdd/0x240 fs/read_write.c:934
    [<ffffffff815f68f6>] do_writev+0xa6/0x1c0 fs/read_write.c:977
    [<ffffffff848802d5>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
    [<ffffffff848802d5>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
    [<ffffffff84a00087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd

In nci_rx_data_packet(), if we don't get a valid conn_info, we will return
directly but forget to release the skb.

Reported-by: syzbot+cdb9a427d1bc08815104@syzkaller.appspotmail.com
Fixes: 4aeee687 ("NFC: nci: Add dynamic logical connections support")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Link: https://lore.kernel.org/r/20221118082419.239475-1-liushixin2@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In commit f11fe1da ("net/sched: Make NET_ACT_CT depends on NF_NAT"),
it fixed the build failure when NF_NAT is m and NET_ACT_CT is y by
adding depends on NF_NAT for NET_ACT_CT. However, it would also cause
NET_ACT_CT cannot be built without NF_NAT, which is not expected. This
patch fixes it by changing to use "(!NF_NAT || NF_NAT)" as the depend.

Fixes: f11fe1da ("net/sched: Make NET_ACT_CT depends on NF_NAT")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/b6386f28d1ba34721795fb776a91cbdabb203447.1668807183.git.lucien.xin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

If phylink_of_phy_connect() fails, the port should be disabled.
If sparx5_serdes_set()/phy_power_on() fails, the port should be
disabled and the phylink should be stopped and disconnected.

Fixes: 946e7fd5 ("net: sparx5: add port module support")
Fixes: f3cad261 ("net: sparx5: add hostmode with phylink support")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Tested-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Link: https://lore.kernel.org/r/20221117125918.203997-1-liujian56@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The __ef100_hard_start_xmit() returns NETDEV_TX_OK without freeing skb
in error handling case, add dev_kfree_skb_any() to fix it.

Fixes: 51b35a45 ("sfc: skeleton EF100 PF driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/1668671409-10909-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

acpi_evaluate_dsm() should be coupled with ACPI_FREE() to free the ACPI
memory, because we need to track the allocation of acpi_object when
ACPI_DBG_TRACK_ALLOCATIONS enabled, so use ACPI_FREE() instead of kfree().

Fixes: d38a648d ("net: wwan: iosm: fix memory leak in ipc_pcie_read_bios_cfg")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20221118062447.2324881-1-bobo.shaobowang@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Commit 1229b339 ("ice: Add low latency Tx timestamp read") refactored
PTP timestamping logic to use a threaded IRQ instead of a separate kthread.

This implementation introduced ice_misc_intr_thread_fn and redefined the
ice_ptp_process_ts function interface to return a value of whether or not
the timestamp processing was complete.

ice_misc_intr_thread_fn would take the return value from ice_ptp_process_ts
and convert it into either IRQ_HANDLED if there were no more timestamps to
be processed, or IRQ_WAKE_THREAD if the thread should continue processing.

This is not correct, as the kernel does not re-schedule threaded IRQ
functions automatically. IRQ_WAKE_THREAD can only be used by the main IRQ
function.

This results in the ice_ptp_process_ts function (and in turn the
ice_ptp_tx_tstamp function) from only being called exactly once per
interrupt.

If an application sends a burst of Tx timestamps without waiting for a
response, the interrupt will trigger for the first timestamp. However,
later timestamps may not have arrived yet. This can result in dropped or
discarded timestamps. Worse, on E822 hardware this results in the interrupt
logic getting stuck such that no future interrupts will be triggered. The
result is complete loss of Tx timestamp functionality.

Fix this by modifying the ice_misc_intr_thread_fn to perform its own
polling of the ice_ptp_process_ts function. We sleep for a few microseconds
between attempts to avoid wasting significant CPU time. The value was
chosen to allow time for the Tx timestamps to complete without wasting so
much time that we overrun application wait budgets in the worst case.

The ice_ptp_process_ts function also currently returns false in the event
that the Tx tracker is not initialized. This would result in the threaded
IRQ handler never exiting if it gets started while the tracker is not
initialized.

Fix the function to appropriately return true when the tracker is not
initialized.

Note that this will not reproduce with default ptp4l behavior, as the
program always synchronously waits for a timestamp response before sending
another timestamp request.
Reported-by: Siddaraju DH <siddaraju.dh@intel.com>
Fixes: 1229b339 ("ice: Add low latency Tx timestamp read")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20221118222729.1565317-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If skb_linearize() fails in tipc_disc_rcv(), we need to free the skb instead of
handle it.

Fixes: 25b0b9c4 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/20221119072832.7896-1-yuehaibing@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-11-18 (iavf)

Ivan Vecera resolves issues related to reset by adding back call to
netif_tx_stop_all_queues() and adding calls to dev_close() to ensure
device is properly closed during reset.

Stefan Assmann removes waiting for setting of MAC address as this breaks
ARP.

Slawomir adds setting of __IAVF_IN_REMOVE_TASK bit to prevent deadlock
between remove and shutdown.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  iavf: Fix race condition between iavf_shutdown and iavf_remove
  iavf: remove INITIAL_MAC_SET to allow gARP to work properly
  iavf: Do not restart Tx queues after reset task failure
  iavf: Fix a crash during reset task
====================

Link: https://lore.kernel.org/r/20221118222439.1565245-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Xin Long says:

====================
tipc: fix two race issues in tipc_conn_alloc

The race exists beteen tipc_topsrv_accept() and tipc_conn_close(),
one is allocating the con while the other is freeing it and there
is no proper lock protecting it. Therefore, a null-pointer-defer
and a use-after-free may be triggered, see details on each patch.
====================

Link: https://lore.kernel.org/r/cover.1668807842.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

One extra conn_get() is needed in tipc_conn_alloc(), as after
tipc_conn_alloc() is called, tipc_conn_close() may free this
con before deferencing it in tipc_topsrv_accept():

   tipc_conn_alloc();
   newsk = newsock->sk;
                                 <---- tipc_conn_close();
   write_lock_bh(&sk->sk_callback_lock);
   newsk->sk_data_ready = tipc_conn_data_ready;

Then an uaf issue can be triggered:

  BUG: KASAN: use-after-free in tipc_topsrv_accept+0x1e7/0x370 [tipc]
  Call Trace:
   <TASK>
   dump_stack_lvl+0x33/0x46
   print_report+0x178/0x4b0
   kasan_report+0x8c/0x100
   kasan_check_range+0x179/0x1e0
   tipc_topsrv_accept+0x1e7/0x370 [tipc]
   process_one_work+0x6a3/0x1030
   worker_thread+0x8a/0xdf0

This patch fixes it by holding it in tipc_conn_alloc(), then after
all accessing in tipc_topsrv_accept() releasing it. Note when does
this in tipc_topsrv_kern_subscr(), as tipc_conn_rcv_sub() returns
0 or -1 only, we don't need to check for "> 0".

Fixes: c5fa7b3c ("tipc: introduce new TIPC server infrastructure")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A crash was reported by Wei Chen:

  BUG: kernel NULL pointer dereference, address: 0000000000000018
  RIP: 0010:tipc_conn_close+0x12/0x100
  Call Trace:
   tipc_topsrv_exit_net+0x139/0x320
   ops_exit_list.isra.9+0x49/0x80
   cleanup_net+0x31a/0x540
   process_one_work+0x3fa/0x9f0
   worker_thread+0x42/0x5c0

It was caused by !con->sock in tipc_conn_close(). In tipc_topsrv_accept(),
con is allocated in conn_idr then its sock is set:

  con = tipc_conn_alloc();
  ...                    <----[1]
  con->sock = newsock;

If tipc_conn_close() is called in anytime of [1], the null-pointer-def
is triggered by con->sock->sk due to con->sock is not yet set.

This patch fixes it by moving the con->sock setting to tipc_conn_alloc()
under s->idr_lock. So that con->sock can never be NULL when getting the
con from s->conn_idr. It will be also safer to move con->server and flag
CF_CONNECTED setting under s->idr_lock, as they should all be set before
tipc_conn_alloc() is called.

Fixes: c5fa7b3c ("tipc: introduce new TIPC server infrastructure")
Reported-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix to return a negative error code from the ccr read error handling
case instead of 0, as done elsewhere in this function.

Fixes: 3265f421 ("net: phy: at803x: add fiber support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221118103635.254256-1-weiyongjun@huaweicloud.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This code accidentally uses the RX macro twice instead of the RX and TX.

Fixes: 6c635f78 ("octeontx2-af: cn10k: mcs: Handle MCS block interrupts")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Zero-length arrays are deprecated[1] and are being replaced with
flexible array members in support of the ongoing efforts to tighten the
FORTIFY_SOURCE routines on memcpy(), correctly instrument array indexing
with UBSAN_BOUNDS, and to globally enable -fstrict-flex-arrays=3.

Replace zero-length array with flexible-array member in struct key_vector.

This results in no differences in binary output.

[1] https://github.com/KSPP/linux/issues/78

Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Ahern <dsahern@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The `nettest` binary, built from `selftests/net/nettest.c`,
was expected to be found in the path during test execution of
`fcnal-test.sh` and `pmtu.sh`, leading to tests getting
skipped when the binary is not installed in the system, as can
be seen in these logs found in the wild [1]:

  # TEST: vti4: PMTU exceptions                                         [SKIP]
  [  350.600250] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
  [  350.607421] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
  # 'nettest' command not found; skipping tests
  #   xfrm6udp not supported
  # TEST: vti6: PMTU exceptions (ESP-in-UDP)                            [SKIP]
  [  351.605102] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
  [  351.612243] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
  # 'nettest' command not found; skipping tests
  #   xfrm4udp not supported

The `unicast_extensions.sh` tests also rely on `nettest`, but
it runs fine there because it looks for the binary in the
current working directory [2]:

The same mechanism that works for the Unicast extensions tests
is here copied over to the PMTU and functional tests.

[1] https://lkft.validation.linaro.org/scheduler/job/5839508#L6221
[2] https://lkft.validation.linaro.org/scheduler/job/5839508#L7958Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains late Netfilter fixes for net:

1) Use READ_ONCE()/WRITE_ONCE() to update ct->mark, from Daniel Xu.
   Not reported by syzbot, but I presume KASAN would trigger post
   a splat on this. This is a rather old issue, predating git history.

2) Do not set up extensions for set element with end interval flag
   set on. This leads to bogusly skipping this elements as expired
   when listing the set/map to userspace as well as increasing
   memory consumpton when stateful expressions are used. This issue
   has been present since 4.18, when timeout support for rbtree set
   was added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Function sparx5_tc_setup_qdisc_ets() always returns negative value
because it return -EOPNOTSUPP in the end. This patch returns the
rersult of sparx5_tc_ets_add() and sparx5_tc_ets_del() directly.

Fixes: 21122542 ("net: microchip: sparx5: add support for offloading ets qdisc")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shang XiaoJing says:

====================
nfc: Fix potential memory leak of skb

There are still somewhere maybe leak the skb, fix the memleaks by adding
fail path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

s3fwrn5_nci_send() won't free the skb when it failed for the check
before s3fwrn5_write(). As the result, the skb will memleak. Free the
skb when the check failed.

Fixes: c04c674f ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

nxp_nci_send() won't free the skb when it failed for the check before
write(). As the result, the skb will memleak. Free the skb when the
check failed.

Fixes: dece4585 ("NFC: nxp-nci: Add support for NXP NCI chips")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfcmrvl_i2c_nci_send() will be called by nfcmrvl_nci_send(), and skb
should be freed in nfcmrvl_i2c_nci_send(). However, nfcmrvl_nci_send()
won't free the skb when it failed for the test_bit(). Free the skb when
test_bit() failed.

Fixes: b5b3e23e ("NFC: nfcmrvl: add i2c driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

'ret' is defined twice in macsec_changelink(), when it is set in macsec_is_offloaded
case, it will be invalid before return.

Fixes: 3cf3227a ("net: macsec: hardware offloading infrastructure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20221118011249.48112-1-yuehaibing@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, we get icmp6hdr via function icmp6_hdr(), which needs the skb
transport header to be set first. But there is no rule to ask driver set
transport header before netif_receive_skb() and bond_handle_frame(). So
we will not able to get correct icmp6hdr on some drivers.

Fix this by using skb_header_pointer to get the IPv6 and ICMPV6 headers.
Reported-by: Liang Li <liali@redhat.com>
Fixes: 4e24be01 ("bonding: add new parameter ns_targets")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20221118034353.1736727-1-liuhangbin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Simon Horman says:

====================
nfp: fixes for v6.1

 - Ensure that information displayed by "devlink port show"
           reflects the number of lanes available to be split.
 - Avoid NULL dereference in ethtool test code.
====================

Link: https://lore.kernel.org/r/20221117153744.688595-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Setting of the port flag `NFP_PORT_CHANGED`, introduced
to ensure the correct reading of EEPROM data, causes a
fatal kernel NULL pointer dereference in cases where
the target netdev type cannot be determined.

Add validation of port struct pointer before attempting
to set the `NFP_PORT_CHANGED` flag. Return that operation
is not supported if the netdev type cannot be determined.

Fixes: 4ae97cae ("nfp: ethtool: fix the display error of `ethtool -m DEVNAME`")
Signed-off-by: Jaco Coetzee <jaco.coetzee@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The error is reflected in that it shows wrong splittable status of
port when executing "devlink port show".
The reason which leads the error is that the assigned operation of
splittable is just a simple negation operation of split and it does
not consider port lanes quantity. A splittable port should have
several lanes that can be split(lanes quantity > 1).
If without the judgement, it will show wrong message for some
firmware, such as 2x25G, 2x10G.

Fixes: a0f49b54 ("devlink: Add a new devlink port split ability attribute and pass to netlink")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().

In pch_gbe_probe(), pci_get_domain_bus_and_slot() is called,
so in error path in probe() and remove() function, pci_dev_put()
should be called to avoid refcount leak. Compile tested only.

Fixes: 1a0bdadb ("net/pch_gbe: supports eg20t ptp clock")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117135148.301014-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().

So before returning from rvu_dbg_rvu_pf_cgx_map_display() or
cgx_print_dmac_flt(), pci_dev_put() is called to avoid refcount
leak.

Fixes: dbc52deb ("octeontx2-af: Debugfs support for DMAC filters")
Fixes: e2fb3730 ("octeontx2-af: Display CGX, NIX and PF map in debugfs.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117124658.162409-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The ql3xxx_send() returns NETDEV_TX_OK without freeing skb in error
handling case, add dev_kfree_skb_any() to fix it.

Fixes: bd36b0ac ("qla3xxx: Add support for Qlogic 4032 chip.")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1668675039-21138-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It will cause invalid pointer dereference to priv->cm3_base behind,
if PTR_ERR(priv->cm3_base) in mvpp2_get_sram().

Fixes: e54ad1e0 ("net: mvpp2: add CM3 SRAM memory map")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Link: https://lore.kernel.org/r/20221117084032.101144-1-tanghui20@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If mlx4_bitmap_init fails, mlx4_bitmap_alloc_range will dereference
the NULL pointer (bitmap->table).

Make sure, that mlx4_bitmap_alloc_range called in no error case.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: d57febe1 ("net/mlx4: Add A0 hybrid steering")
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Peter Kosyh <pkosyh@yandex.ru>
Link: https://lore.kernel.org/r/20221117152806.278072-1-pkosyh@yandex.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If mtk_start_dma() fails, invoke phylink_disconnect_phy() to perform
cleanup. phylink_disconnect_phy() contains the put_device action. If
phylink_disconnect_phy is not performed, the Kref of netdev will leak.

Fixes: b8fc9f30 ("net: ethernet: mediatek: Add basic PHYLINK support")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221117111356.161547-1-liujian56@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix a deadlock introduced by commit
97457801 ("iavf: Add waiting so the port is initialized in remove")
due to race condition between iavf_shutdown and iavf_remove, where
iavf_remove stucks forever in while loop since iavf_shutdown already
set __IAVF_REMOVE adapter state.

Fix this by checking if the __IAVF_IN_REMOVE_TASK has already been
set and return if so.

Fixes: 97457801 ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

IAVF_FLAG_INITIAL_MAC_SET prevents waiting on iavf_is_mac_set_handled()
the first time the MAC is set. This breaks gratuitous ARP because the
MAC address has not been updated yet when the gARP packet is sent out.

Current behaviour:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: ee:04:19:14:ec:ea
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:23:41.676611 ee:04:19:14:ec:ea > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28

With IAVF_FLAG_INITIAL_MAC_SET removed:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: 3e:8a:16:a2:37:6d
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:28:01.836608 00:11:22:33:44:55 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28

Fixes: 35a2443d ("iavf: Add waiting for response from PF in set mac")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

After commit aa626da9 ("iavf: Detach device during reset task")
the device is detached during reset task and re-attached at its end.
The problem occurs when reset task fails because Tx queues are
restarted during device re-attach and this leads later to a crash.

To resolve this issue properly close the net device in cause of
failure in reset task to avoid restarting of tx queues at the end.
Also replace the hacky manipulation with IFF_UP flag by device close
that clears properly both IFF_UP and __LINK_STATE_START flags.
In these case iavf_close() does not do anything because the adapter
state is already __IAVF_DOWN.

Reproducer:
1) Run some Tx traffic (e.g. iperf3) over iavf interface
2) Set VF trusted / untrusted in loop

[root@host ~]# cat repro.sh

PF=enp65s0f0
IF=${PF}v0

ip link set up $IF
ip addr add 192.168.0.2/24 dev $IF
sleep 1

iperf3 -c 192.168.0.1 -t 600 --logfile /dev/null &
sleep 2

while :; do
        ip link set $PF vf 0 trust on
        ip link set $PF vf 0 trust off
done
[root@host ~]# ./repro.sh

Result:
[ 2006.650969] iavf 0000:41:01.0: Failed to init adminq: -53
[ 2006.675662] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.689997] iavf 0000:41:01.0: Reset task did not complete, VF disabled
[ 2006.696611] iavf 0000:41:01.0: failed to allocate resources during reinit
[ 2006.703209] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.737011] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.764536] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.768919] BUG: kernel NULL pointer dereference, address: 0000000000000b4a
[ 2006.776358] #PF: supervisor read access in kernel mode
[ 2006.781488] #PF: error_code(0x0000) - not-present page
[ 2006.786620] PGD 0 P4D 0
[ 2006.789152] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 2006.792903] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.793501] CPU: 4 PID: 0 Comm: swapper/4 Kdump: loaded Not tainted 6.1.0-rc3+ #2
[ 2006.805668] Hardware name: Abacus electric, s.r.o. - servis@abacus.cz Super Server/H12SSW-iN, BIOS 2.4 04/13/2022
[ 2006.815915] RIP: 0010:iavf_xmit_frame_ring+0x96/0xf70 [iavf]
[ 2006.821028] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.821572] Code: 48 83 c1 04 48 c1 e1 04 48 01 f9 48 83 c0 10 6b 50 f8 55 c1 ea 14 45 8d 64 14 01 48 39 c8 75 eb 41 83 fc 07 0f 8f e9 08 00 00 <0f> b7 45 4a 0f b7 55 48 41 8d 74 24 05 31 c9 66 39 d0 0f 86 da 00
[ 2006.845181] RSP: 0018:ffffb253004bc9e8 EFLAGS: 00010293
[ 2006.850397] RAX: ffff9d154de45b00 RBX: ffff9d15497d52e8 RCX: ffff9d154de45b00
[ 2006.856327] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.857523] RDX: 0000000000000000 RSI: 00000000000005a8 RDI: ffff9d154de45ac0
[ 2006.857525] RBP: 0000000000000b00 R08: ffff9d159cb010ac R09: 0000000000000001
[ 2006.857526] R10: ffff9d154de45940 R11: 0000000000000000 R12: 0000000000000002
[ 2006.883600] R13: ffff9d1770838dc0 R14: 0000000000000000 R15: ffffffffc07b8380
[ 2006.885840] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.890725] FS:  0000000000000000(0000) GS:ffff9d248e900000(0000) knlGS:0000000000000000
[ 2006.890727] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2006.909419] CR2: 0000000000000b4a CR3: 0000000c39c10002 CR4: 0000000000770ee0
[ 2006.916543] PKRU: 55555554
[ 2006.918254] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.919248] Call Trace:
[ 2006.919250]  <IRQ>
[ 2006.919252]  dev_hard_start_xmit+0x9e/0x1f0
[ 2006.932587]  sch_direct_xmit+0xa0/0x370
[ 2006.936424]  __dev_queue_xmit+0x7af/0xd00
[ 2006.940429]  ip_finish_output2+0x26c/0x540
[ 2006.944519]  ip_output+0x71/0x110
[ 2006.947831]  ? __ip_finish_output+0x2b0/0x2b0
[ 2006.952180]  __ip_queue_xmit+0x16d/0x400
[ 2006.952721] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.956098]  __tcp_transmit_skb+0xa96/0xbf0
[ 2006.965148]  __tcp_retransmit_skb+0x174/0x860
[ 2006.969499]  ? cubictcp_cwnd_event+0x40/0x40
[ 2006.973769]  tcp_retransmit_skb+0x14/0xb0
...

Fixes: aa626da9 ("iavf: Detach device during reset task")
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Patryk Piotrowski <patryk.piotrowski@intel.com>
Cc: SlawomirX Laba <slawomirx.laba@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Recent commit aa626da9 ("iavf: Detach device during reset task")
removed netif_tx_stop_all_queues() with an assumption that Tx queues
are already stopped by netif_device_detach() in the beginning of
reset task. This assumption is incorrect because during reset
task a potential link event can start Tx queues again.
Revert this change to fix this issue.

Reproducer:
1. Run some Tx traffic (e.g. iperf3) over iavf interface
2. Switch MTU of this interface in a loop

[root@host ~]# cat repro.sh

IF=enp2s0f0v0

iperf3 -c 192.168.0.1 -t 600 --logfile /dev/null &
sleep 2

while :; do
        for i in 1280 1500 2000 900 ; do
                ip link set $IF mtu $i
                sleep 2
        done
done
[root@host ~]# ./repro.sh

Result:
[  306.199917] iavf 0000:02:02.0 enp2s0f0v0: NIC Link is Up Speed is 40 Gbps Full Duplex
[  308.205944] iavf 0000:02:02.0 enp2s0f0v0: NIC Link is Up Speed is 40 Gbps Full Duplex
[  310.103223] BUG: kernel NULL pointer dereference, address: 0000000000000008
[  310.110179] #PF: supervisor write access in kernel mode
[  310.115396] #PF: error_code(0x0002) - not-present page
[  310.120526] PGD 0 P4D 0
[  310.123057] Oops: 0002 [#1] PREEMPT SMP NOPTI
[  310.127408] CPU: 24 PID: 183 Comm: kworker/u64:9 Kdump: loaded Not tainted 6.1.0-rc3+ #2
[  310.135485] Hardware name: Abacus electric, s.r.o. - servis@abacus.cz Super Server/H12SSW-iN, BIOS 2.4 04/13/2022
[  310.145728] Workqueue: iavf iavf_reset_task [iavf]
[  310.150520] RIP: 0010:iavf_xmit_frame_ring+0xd1/0xf70 [iavf]
[  310.156180] Code: d0 0f 86 da 00 00 00 83 e8 01 0f b7 fa 29 f8 01 c8 39 c6 0f 8f a0 08 00 00 48 8b 45 20 48 8d 14 92 bf 01 00 00 00 4c 8d 3c d0 <49> 89 5f 08 8b 43 70 66 41 89 7f 14 41 89 47 10 f6 83 82 00 00 00
[  310.174918] RSP: 0018:ffffbb5f0082caa0 EFLAGS: 00010293
[  310.180137] RAX: 0000000000000000 RBX: ffff92345471a6e8 RCX: 0000000000000200
[  310.187259] RDX: 0000000000000000 RSI: 000000000000000d RDI: 0000000000000001
[  310.194385] RBP: ffff92341d249000 R08: ffff92434987fcac R09: 0000000000000001
[  310.201509] R10: 0000000011f683b9 R11: 0000000011f50641 R12: 0000000000000008
[  310.208631] R13: ffff923447500000 R14: 0000000000000000 R15: 0000000000000000
[  310.215756] FS:  0000000000000000(0000) GS:ffff92434ee00000(0000) knlGS:0000000000000000
[  310.223835] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  310.229572] CR2: 0000000000000008 CR3: 0000000fbc210004 CR4: 0000000000770ee0
[  310.236696] PKRU: 55555554
[  310.239399] Call Trace:
[  310.241844]  <IRQ>
[  310.243855]  ? dst_alloc+0x5b/0xb0
[  310.247260]  dev_hard_start_xmit+0x9e/0x1f0
[  310.251439]  sch_direct_xmit+0xa0/0x370
[  310.255276]  __qdisc_run+0x13e/0x580
[  310.258848]  __dev_queue_xmit+0x431/0xd00
[  310.262851]  ? selinux_ip_postroute+0x147/0x3f0
[  310.267377]  ip_finish_output2+0x26c/0x540

Fixes: aa626da9 ("iavf: Detach device during reset task")
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Patryk Piotrowski <patryk.piotrowski@intel.com>
Cc: SlawomirX Laba <slawomirx.laba@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Elements with an end interval flag set on do not store extensions. The
global set definition is currently setting on the timeout and stateful
expression for end interval elements.

This leads to skipping end interval elements from the set->ops->walk()
path as the expired check bogusly reports true.

Moreover, do not set up stateful expressions for elements with end
interval flag set on since this is never used.

Fixes: 65038428 ("netfilter: nf_tables: allow to specify stateful expression in set definition")
Fixes: 8d8540c4 ("netfilter: nft_set_rbtree: add timeout support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

nf_conn:mark can be read from and written to in parallel. Use
READ_ONCE()/WRITE_ONCE() for reads and writes to prevent unwanted
compiler optimizations.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

In pch_gbe_xmit_frame(), NETDEV_TX_OK will be returned whether
pch_gbe_tx_queue() sends data successfully or not, so pch_gbe_tx_queue()
needs to free skb before returning. But pch_gbe_tx_queue() returns without
freeing skb in case of dma_map_single() fails. Add dev_kfree_skb_any()
to fix it.

Fixes: 77555ee7 ("net: Add Gigabit Ethernet driver of Topcliff PCH")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously we leverage NCI_UNREG and the lock inside nci_close_device to
prevent the race condition between opening a device and closing a
device. However, it still has problem because a failed opening command
will erase the NCI_UNREG flag and allow another opening command to
bypass the status checking.

This fix corrects that by making sure the NCI_UNREG is held.

Reported-by: syzbot+43475bf3cfbd6e41f5b7@syzkaller.appspotmail.com
Fixes: 48b71a9e ("NFC: add NCI_UNREG flag to eliminate the race")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>