- 06 Jun, 2014 9 commits
-
-
Shannon Nelson authored
Add the missing unicast, multicast, and broadcast stats for the port. Change-ID: Ifc366d7b7745f70eaac9d00eeb0694eb9ec076a9 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Shannon Nelson authored
Add VSI HW stats for unicast, multicast, and broadcast for Rx and Tx. Stop printing the netdev multicast value because it doesn't include Tx and would be confusing. Change-ID: I08278b6657e7c838fd29a4a1f305f78fe1b150be Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Shannon Nelson authored
The wait time was originally too optimistic and the resets were failing after EMPR. This increases the loop count to wait considerably longer. This won't delay the actual wait longer than really needed, just allows us to poll more times as needed. Change-ID: If7b96f55cc25b8d06cbbe8665259d250188c53d7 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Matt Jared authored
Add a function which indicates our intention to enable or disable a particular Tx queue. Also add a function to notify the device's Tx unit that we're about to enable or disable a Tx queue. Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d Signed-off-by: Matt Jared <matthew.a.jared@intel.com> Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Kamil Krawczyk authored
B0 Si blocks AQ registers when in Blank Flash mode - write is dropped, read gives 0xDEADBEEF. Introduce a simple check for a correct value in one of the AQ registers to be sure that AQ was configured correctly. Without this check we get into an endless loop while trying to send GetVersion AQ cmd. Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Mitch Williams authored
Depending on the timing of what the PF driver is doing, it make take a few tries before the VF driver is able to communicate with the PF driver on init or reset recovery. In order to prevent confusion, make the most common messages less scary by lowering them to a less terrifying log level and indicate that the driver will retry. Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jesse Brandeburg authored
The driver and hardware are not expected to work correctly with revision_id 0 hardware. Don't prevent the user from using it, but be sure to print a warning. Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Shannon Nelson authored
Print the VEB statistics in the ethtool stats output. Change-ID: Ic93d4c3922345c43e4cfd7f7e7a906844dd2f49f Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Shannon Nelson authored
When the VEB is created for the basic LAN device and its VSIs, we need to set the tracking lan_veb index for later use. Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 05 Jun, 2014 31 commits
-
-
Sven Wegener authored
To avoid the confusion of having two variables, shrink the function to only use the parameter variable for looping. Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller authored
Conflicts: drivers/net/xen-netback/netback.c net/core/filter.c A filter bug fix overlapped some cleanups and a conversion over to some new insn generation macros. A xen-netback bug fix overlapped the addition of multi-queue support. Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexei Starovoitov authored
BPF classic->internal converter broke SKF_AD_PKTTYPE extension, since pkt_type_offset() was failing to find skb->pkt_type field which is defined as: __u8 pkt_type:3, fclone:2, ipvs_property:1, peeked:1, nf_trace:1; Fix it by searching for 3 most significant bits and shift them by 5 at run-time Fixes: bd4cf0ed ("net: filter: rework/optimize internal BPF interpreter's instruction set") Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Tested-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Konrad Zapalowicz authored
This commit fixes the following sparse warning: drivers/net/phy/fixed.c:207 - warning: symbol 'fixed_phy_del' was not declared. Should it be static? by adding symbol definition to the phy_fixed.h API file. It is ok to do because the function in question is an exported symbol. Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Florian Fainelli says: ==================== net: systemport: misc fixes This patch series contains some misc fixes for the SYSTEMPORT driver. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
The SYSTEMPORT driver uses libphy to determine the carrier state, so make sure we start with a carrier off until libphy has completed the link training process. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
The comment about how the hardware prepends 2bytes to align the IP header on a 4-byte boundary was not correct, fix that. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
We were missing an and comparison with status to check whether RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix that. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Our transmit locking scheme did not account for the TX ring full interrupt. If a TX ring full interrupt fires while we are attempting to transmit, we will cause a deadlock to occur. Fix this by making sure that we properly disable interrupts while acquiring the spinlock. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter/nf_tables fixes for net-next This patchset contains fixes for recent updates available in your net-next, they are: 1) Fix double memory allocation for accounting objects that results in a leak, this slipped through with the new quota extension, patch from Mathieu Poirier. 2) Fix broken ordering when adding set element transactions. 3) Make sure that objects are released in reverse order in the abort path, to avoid possible use-after-free when accessing dependencies. 4) Allow to delete several objects (as long as dependencies are fulfilled) by using one batch. This includes changes in the use counter semantics of the nf_tables objects. 5) Fix illegal sleeping allocation from rcu callback. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Tom Lendacky says: ==================== amd-xgbe: AMD 10Gb Ethernet driver The following series implements support for the new AMD 10Gb Ethernet driver (amd-xgbe). It includes the 10Gb Ethernet driver as well as a 10Gb Ethernet PHY driver. This patch series is based on net-next. Changes in V3: - Add OF dependency to the phylib driver configuration ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
This patch adds the maintainer information for the AMD 10GbE platform driver. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
This patch provides the Kconfig and Makefile changes needed to configure and build the AMD 10GbE platform driver and the AMD 10GbE phylib driver. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
This patch provides the initial phylib driver in support of the AMD 10GbE device. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
This patch provides the initial platform driver for the AMD 10GbE device. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
This patch provides the documentation of the device bindings for the AMD 10GbE platform driver. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Toshiaki Makita authored
br_manage_promisc() incorrectly expects br_auto_port() to return only 0 or 1, while it actually returns flags, i.e., a subset of BR_AUTO_MASK. Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amos Kong authored
drivers/net/ethernet/amd/hplance.h: #define HPLANCE_MEMOFF 0x8000 /* struct lance_init_block */ #define HPLANCE_NVRAMOFF 0xC008 /* etheraddress as one *nibble* per byte */ The offset of RAM start is 0x8000, the offset of RAM end is 0xC008, so the RAM size is 16392 bytes. Signed-off-by: Amos Kong <akong@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amos Kong authored
The order of ram pages is 3, so the ram size is 2^3 * 4K = 32K. Signed-off-by: Amos Kong <akong@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Andrew Ruder says: ==================== miscellaneous dm9000 driver fixes This is a collection of changes discovered while bringing a PXA270 based board (Arcom ZEUS) with a Davicom DM9000A/B up to a more recent kernel (from 2.6.xx). This addresses all of my earlier issues (August 2013) listed here: http://marc.info/?l=linux-netdev&m=137598605603324&w=2 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Ruder authored
On the DM9000B, dm9000_msleep() is called during the dm9000_timeout() routine. Since dm9000_timeout() holds the main spinlock through the entire routine, mdelay() needs to be used rather than msleep(). Furthermore, the mutex_lock()/mutex_unlock() should be avoided so as to not sleep with spinlocks held. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Ruder authored
On the DM9000A/DM9000B force the initial check of the link status. The DM9000A/B has a link status changed event and this interrupt bit isn't always set out of reset when a cable is plugged in. This results in the driver not seeing the cable attached link status until the cable is removed and plugged in again. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Ruder authored
Since dm9000_interrupt() is already reading/clearing every set bit in DM9000_ISR, this additional clear in dm9000_rx() (which is only called by dm9000_interrupt()) is unnecessary and can be removed. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Ruder authored
DM9000 uses level-triggered interrupts. Some systems (PXA270) only support edge-triggered interrupts on GPIOs. Some changes are necessary to ensure that interrupts are not triggered while the GPIO interrupt is masked or we will miss the interrupt forever. * Make some helper functions called dm9000_mask_interrupts() and dm9000_unmask_interrupts() for readability. * dm9000_init_dm9000(): ensure that this function always leaves interrupts masked regardless of the state when it entered the function. This is primarily to support the situation in dm9000_open where the logic used to go: dm9000_open() dm9000_init_dm9000() unmask interrupts request_irq() If an interrupt occurred between unmasking the interrupt and requesting the irq, it would be missed forever as the edge event would never be seen by the GPIO hardware in the PXA270. This allows us to change the logic to: dm9000_open() dm9000_init_dm9000() dm9000_mask_interrupts() request_irq() dm9000_unmask_interrupts() * dm9000_timeout(), dm9000_drv_resume(): Add the missing dm9000_unmask_interrupts() now required by the change above. * dm9000_shutdown(): Use mask helper function * dm9000_interrupt(): Use mask/unmask helper functions Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Ruder authored
* Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset * Every single place where dm9000_init_dm9000 was ran, a dm9000_reset was called immediately before-hand. Bring dm9000_reset into dm9000_init_dm9000. * The following commit updated the dm9000_probe reset routine to use NCR_RST | NCR_MAC_LBK: 6741f40 DM9000B: driver initialization upgrade and a later commit added a bug-fix to always reset the chip twice: 09ee9f87 dm9000: Implement full reset of DM9000 network device Unfortunately, since the changes in 6741f40 were made by replacing the dm9000_probe dm9000_reset with the adjusted iow(), the changes in 09ee9f87 were not incorporated into the dm9000_probe reset. Furthermore, it bypassed the requisite reset-delay causing some boards to get at least one "read wrong id ..." dev_err message during dm9000_probe. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andrew Ruder authored
The DM9000 supports both active high interrupts and active low interrupts. This is configured via the attached EEPROM. In the device-tree case, make sure that the DM9000 driver passes the correct flags to request_irq. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Zoltan Kiss authored
A recent commit (a02eb4 "xen-netback: worse-case estimate in xenvif_rx_action is underestimating") capped the slot estimation to MAX_SKB_FRAGS, but that triggers the next BUG_ON a few lines down, as the packet consumes more slots than estimated. This patch introduces full_coalesce on the skb callback buffer, which is used in start_new_rx_buffer() to decide whether netback needs coalescing more aggresively. By doing that, no packet should need more than (XEN_NETIF_MAX_TX_SIZE + 1) / PAGE_SIZE data slots (excluding the optional GSO slot, it doesn't carry data, therefore irrelevant in this case), as the provided buffers are fully utilized. Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com> Cc: Paul Durrant <paul.durrant@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Paul Durrant <paul.durrant@gmail.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rajesh Borundia authored
o Uninitialzed fields in mailbox command structure caused commands to time out randomly due to garbage values so initialize it to zero. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Simon Horman authored
If an MPLS packet requires segmentation then use mpls_features to determine if the software implementation should be used. As no driver advertises MPLS GSO segmentation this will always be the case. I had not noticed that this was necessary before as software MPLS GSO segmentation was already being used in my test environment. I believe that the reason for that is the skbs in question always had fragments and the driver I used does not advertise NETIF_F_FRAGLIST (which seems to be the case for most drivers). Thus software segmentation was activated by skb_gso_ok(). This introduces the overhead of an extra call to skb_network_protocol() in the case where where CONFIG_NET_MPLS_GSO is set and skb->ip_summed == CHECKSUM_NONE. Thanks to Jesse Gross for prompting me to investigate this. Signed-off-by: Simon Horman <horms@verge.net.au> Acked-by: YAMAMOTO Takashi <yamamoto@valinux.co.jp> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Fabio Estevam authored
Quoting David Miller: "At the moment you call register_netdev() the device is visible, notifications are sent to userspace, and userland tools can try to bring the interface up and see the incorrect link state, before you do the netif_carrier_off(). Said another way, between the register_netdev() and netif_carrier_off() call, userspace can see the device in an inconsistent state." So call netif_carrier_off() prior to register_netdev(). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2014-06-05 This series contains updates to i40e and i40evf. Jesse fixes an issue reported by Dave Jones where a couple of FD checks ended up using bitwise OR where it should have been bitwise AND. Neerav removes unused defines and macros for receive LRO. Fix the driver from allowing the user to set a larger MTU size that the hardware was being configured to support. Refactors send version which moves code in two places into a small helper function. Kamil modifies register diagnostics since register ranges can vary among the different NVMs to avoid false test results. So now we try to identify the full range and use it for a register test and if we fail to define the proper register range, we will only test the first register from that group. Then removes the check for large buffer since this was added in the case this structure changed in the future, since the AQ definition is now mature enough that this check is no longer necessary. Mitch fixes i40evf driver to allocate descriptors in groups of 32 since the hardware requires it. Also fixes a crash when the ring size changed because it would change the count before deallocating resources, causing the driver to either free nonexistent buffers or leak leftover buffers. Fixed the driver to notify the VF for all types of resets so the VF can attempt a graceful reinit. Shannon refactors stats collection to create a unifying stats update routine to call the various stat collection routines. Removes rx_errors and rx_missed stats since they were removed from the chip design. Added missing VSI statistics that the hardware offers but are not apart of the standard netdev stats. v2: dropped patch "i40e: Allow disabling of DCB via debugfs" from Neerav based on feedback from David Miller. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-