s390 defines a global dump_trace() symbol. Rename ours to
dump_ucode_trace() to avoid a collision in build tests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

In case memory resources for *fw* were allocated, release them
before return.

Addresses-Coverity-ID: 1472044 ("Resource leak")
Fixes: 6a794a27 ("fsi: master-ast-cf: Add new FSI master using Aspeed ColdFire")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Then reading the RTAG/RCRC "registers" from the coprocessor after
a command is complete, mask out the top bits, only keep the relevant
bits. Microcode v5 will leave garbage in those top bits as a
result of a performance optimization.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---

A couple of places forgot the 'z' qualifier for dev_dbg
when printing a size_t
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

They get retrieved from the device-tree and exposed
as an attribute in sysfs
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This represents a physical chip in the system and allows
a stable numbering scheme to be passed to udev for userspace
to recognize which chip is which.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Rob Herring <robh@kernel.org>

Some of the exit path missed the unlock. Move the mutex to
an outer function to avoid the problem completely
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The Aspeed AST2x00 can contain a ColdFire v1 coprocessor which
is currently unused on OpenPower systems.

This adds an alternative to the fsi-master-gpio driver that
uses that coprocessor instead of bit banging from the ARM
core itself. The end result is about 4 times faster.

The firmware for the coprocessor and its source code can be
found at https://github.com/ozbenh/cf-fsi and is system specific.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This isn't per-se a real device, it's a pseudo-device that
represents the use of the Aspeed built-in ColdFire to
implement the FSI protocol by bitbanging the GPIOs instead
of doing it from the ARM core.

Thus it's a drop-in replacement for the existing
fsi-master-gpio pseudo-device for use on systems based
on the Aspeed chips. It has most of the same properties,
plus some more needed to operate the coprocessor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Rob Herring <robh@kernel.org>

There are still quite a few cases where a device might want
to get to a different node of the device-tree, obtain the
resources and map them.

We have of_iomap() and of_io_request_and_map() but they both
have shortcomings, such as not returning the size of the
resource found (which can be useful) and not being "managed".

This adds a devm_of_iomap() that provides all of these and
should probably replace uses of the above in most drivers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

Merge the GPIO tree "ib-aspeed" topic branch which contains pre-requisites
for subsequent changes. This branch is also in gpio "next".

This moves the definitions for various protocol details
(message & response codes, delays etc...) out of
fsi-master-gpio.c to fsi-master.h in order to share them
with other master implementations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

The embedded struct device needs a release function to be
able to successfully remove the driver.

We remove the devm_gpiod_put() as they are unnecessary
(the resources will be released automatically) and because
fsi_master_unregister() will cause the master structure to
be freed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

In the error path of fsi_master_register(), we currently
use device_unregister(). This will cause the last reference
to the structure to be dropped, thus freeing the enclosing
structure, which isn't what the callers want.

Use device_del() instead so that we return to the caller
with a refcount of 1. The caller can then assume that it
must use put_device() after a call to fsi_master_register()
regardless of whether the latter suceeded or failed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Some definitions are generic to the FSI protocol or any
give master implementation. Rename them to remove the
"GPIO" prefix in preparation for moving them to a common
header.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

# Conflicts:
#	drivers/fsi/fsi-master-gpio.c

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

This adds a few more tracepoints that have proven useful when
debugging issues with the FSI bus.

This also makes echo_delay() use clock_zeros() instead of
open-code it in order to share the tracepoint.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

To configure the send and echo delays
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

What the driver called "FSI_GPIO_PRIME_SLAVE_CLOCKS" is what
the FSI spec calls tSendDelay and should be 16 clocks by
default.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

Those values control the amount of "dummy" clocks between commands and
between a command and its response.

This adds a way to configure them from sysfs (to be later extended to
defaults in the device-tree). The default remains 16 (the HW default).

This is only supported if the backend supports the new link_config()
callback to configure the generation of those delays.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
---

Move fsi_slave_set_smode() and its helpers to before it's
first user and remove the corresponding forward declaration.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>

"dev" is dereferences before it's checked.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The driver calls of_platform_device_create() which is only available
if OF_ADDRESS is enabled. When building sparc64 images, this results
in

ERROR: "of_platform_device_create" [drivers/fsi/fsi-sbefifo.ko] undefined!

Fixes: 9f4a8a2d ("fsi/sbefifo: Add driver for the SBE FIFO")
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

There was no unlock of the FFDC mutex.

Fixes: 9f4a8a2d ("fsi/sbefifo: Add driver for the SBE FIFO")
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

On the Aspeed chip, the GPIOs can be under control of the ARM
chip or of the ColdFire coprocessor. (There's a third command
source, the LPC bus, which we don't use or support yet).

The control of which master is allowed to modify a given
GPIO is per-bank (8 GPIOs).

Unfortunately, systems already exist for which we want to
use GPIOs of both sources in the same bank.

This provides an API exported by the gpio-aspeed driver
that an aspeed coprocessor driver can use to "grab" some
GPIOs for use by the coprocessor, and allow the coprocessor
driver to provide callbacks for arbitrating access.

Once at least one GPIO of a given bank has been "grabbed"
by the coprocessor, the entire bank is marked as being
under coprocessor control. It's command source is switched
to the coprocessor.

If the ARM then tries to write to a GPIO in such a marked bank,
the provided callbacks are used to request access from the
coprocessor driver, which is responsible to doing whatever
is necessary to "pause" the coprocessor or prevent it from
trying to use the GPIOs while the ARM is doing its accesses.

During that time, the command source for the bank is temporarily
switched back to the ARM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the definitions for the command source registers
and a helper to set them.

Those registers allow to control which bus master on the
SoC is allowed to modify a given bank of GPIOs and will
be used by subsequent patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Aspeed GPIO hardware has a quirk: the value register, for an
output GPIO, doesn't contain the last value written (the write
latch content) but the sampled input value.

This means that when reading back shortly after writing, you can
get an incorrect value as the input value is delayed by a few
synchronizers.

The HW supports a separate read-only register "Data Read Register"
which allows you to read the write latch instead.

This adds the definition for it, and uses it for the initial
population of the GPIO value cache. It will be used more in
subsequent patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use a single accessor function for all register types instead
of several spread around. This will make it easier/cleaner
to introduce new registers and keep the mechanism in one
place.

The big switch/case is optimized at compile time since the
switch value is a constant.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This was too hard to split ... this adds a number of features
to the SCOM user interface:

 - Support for indirect SCOMs

 - read()/write() interface now handle errors and retries

 - New ioctl() "raw" interface for use by debuggers
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>

Add a few more register and bit definitions, also define and use
SCOM_READ_CMD (which is 0 but it makes the code clearer)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Eddie James <eajames@linux.vnet.ibm.com>

Use the proper annotated type __be32 and fixup the
accessor used for get_scom()
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Eddie James <eajames@linux.vnet.ibm.com>

No functional changes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Eddie James <eajames@linux.vnet.ibm.com>

Otherwise, multiple clients can open the driver and attempt
to access the PIB at the same time, thus clobbering each other
in the process.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Eddie James <eajames@linux.vnet.ibm.com>

fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:210:9: warning: cast to restricted __be32
fsi-core.c:606:15: warning: incorrect type in assignment (different base types)
fsi-core.c:606:15:    expected unsigned int [unsigned] [assigned] [usertype] smode
fsi-core.c:606:15:    got restricted __be32 [usertype] <noident>
fsi-core.c:492:28: warning: expression using sizeof(void)
fsi-core.c:520:29: warning: expression using sizeof(void)
fsi-core.c:682:19: warning: cast to restricted __be32
fsi-core.c:682:19: warning: cast to restricted __be32
fsi-core.c:682:19: warning: cast to restricted __be32
fsi-core.c:682:19: warning: cast to restricted __be32
fsi-core.c:682:19: warning: cast to restricted __be32
fsi-core.c:682:19: warning: cast to restricted __be32
fsi-core.c:706:24: warning: incorrect type in assignment (different base types)
fsi-core.c:706:24:    expected unsigned int [unsigned] [usertype] llmode
fsi-core.c:706:24:    got restricted __be32 [usertype] <noident>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

fsi-master-hub.c:128:13: warning: incorrect type in assignment (different base types)
fsi-master-hub.c:128:13:    expected unsigned int [unsigned] [usertype] cmd
fsi-master-hub.c:128:13:    got restricted __be32 [usertype] <noident>
fsi-master-hub.c:208:13: warning: incorrect type in assignment (different base types)
fsi-master-hub.c:208:13:    expected restricted __be32 [addressable] [assigned] [usertype] reg
fsi-master-hub.c:208:13:    got int
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

fsi-sbefifo.c:547:58: warning: incorrect type in argument 2 (different base types)
fsi-sbefifo.c:547:58:    expected restricted __be32 [usertype] *word
fsi-sbefifo.c:547:58:    got unsigned int *<noident>
fsi-sbefifo.c:635:16: warning: incorrect type in assignment (different base types)
fsi-sbefifo.c:635:16:    expected unsigned int [unsigned] <noident>
fsi-sbefifo.c:635:16:    got restricted __be32 [usertype] <noident>
fsi-sbefifo.c:636:16: warning: incorrect type in assignment (different base types)
fsi-sbefifo.c:636:16:    expected unsigned int [unsigned] <noident>
fsi-sbefifo.c:636:16:    got restricted __be32 [usertype] <noident>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Pull block fixes from Jens Axboe:
 "A collection of fixes that should go into -rc1. This contains:

   - bsg_open vs bsg_unregister race fix (Anatoliy)

   - NVMe pull request from Christoph, with fixes for regressions in
     this window, FC connect/reconnect path code unification, and a
     trace point addition.

   - timeout fix (Christoph)

   - remove a few unused functions (Christoph)

   - blk-mq tag_set reinit fix (Roman)"

* tag 'for-linus-20180616' of git://git.kernel.dk/linux-block:
  bsg: fix race of bsg_open and bsg_unregister
  block: remov blk_queue_invalidate_tags
  nvme-fabrics: fix and refine state checks in __nvmf_check_ready
  nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
  nvme-fabrics: refactor queue ready check
  blk-mq: remove blk_mq_tagset_iter
  nvme: remove nvme_reinit_tagset
  nvme-fc: fix nulling of queue data on reconnect
  nvme-fc: remove reinit_request routine
  blk-mq: don't time out requests again that are in the timeout handler
  nvme-fc: change controllers first connect to use reconnect path
  nvme: don't rely on the changed namespace list log
  nvmet: free smart-log buffer after use
  nvme-rdma: fix error flow during mapping request data
  nvme: add bio remapping tracepoint
  nvme: fix NULL pointer dereference in nvme_init_subsystem
  blk-mq: reinit q->tag_set_list entry only after grace period

Pull documentation fixes from Mauro Carvalho Chehab:
 "This solves a series of broken links for files under Documentation,
  and improves a script meant to detect such broken links (see
  scripts/documentation-file-ref-check).

  The changes on this series are:

   - can.rst: fix a footnote reference;

   - crypto_engine.rst: Fix two parsing warnings;

   - Fix a lot of broken references to Documentation/*;

   - improve the scripts/documentation-file-ref-check script, in order
     to help detecting/fixing broken references, preventing
     false-positives.

  After this patch series, only 33 broken references to doc files are
  detected by scripts/documentation-file-ref-check"

* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
  fix a series of Documentation/ broken file name references
  Documentation: rstFlatTable.py: fix a broken reference
  ABI: sysfs-devices-system-cpu: remove a broken reference
  devicetree: fix a series of wrong file references
  devicetree: fix name of pinctrl-bindings.txt
  devicetree: fix some bindings file names
  MAINTAINERS: fix location of DT npcm files
  MAINTAINERS: fix location of some display DT bindings
  kernel-parameters.txt: fix pointers to sound parameters
  bindings: nvmem/zii: Fix location of nvmem.txt
  docs: Fix more broken references
  scripts/documentation-file-ref-check: check tools/*/Documentation
  scripts/documentation-file-ref-check: get rid of false-positives
  scripts/documentation-file-ref-check: hint: dash or underline
  scripts/documentation-file-ref-check: add a fix logic for DT
  scripts/documentation-file-ref-check: accept more wildcards at filenames
  scripts/documentation-file-ref-check: fix help message
  media: max2175: fix location of driver's companion documentation
  media: v4l: fix broken video4linux docs locations
  media: dvb: point to the location of the old README.dvb-usb file
  ...

Pull fsnotify updates from Jan Kara:
 "fsnotify cleanups unifying handling of different watch types.

  This is the shortened fsnotify series from Amir with the last five
  patches pulled out. Amir has modified those patches to not change
  struct inode but obviously it's too late for those to go into this
  merge window"

* tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fsnotify: add fsnotify_add_inode_mark() wrappers
  fanotify: generalize fanotify_should_send_event()
  fsnotify: generalize send_to_group()
  fsnotify: generalize iteration of marks by object type
  fsnotify: introduce marks iteration helpers
  fsnotify: remove redundant arguments to handle_event()
  fsnotify: use type id to identify connector object type