The change is only hardware, and does not need driver change:
Added hardware flow control during transmit packet with variable delay.
The new id is then added to the ids list structure.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211215141727.4901-2-yann.gautier@foss.st.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

During test campaign, and especially after several unbind/bind sequences,
it has been seen that the SD-card on SDMMC1 thread could freeze.
The freeze always appear on a CMD23 following a CMD19.
Checking SDMMC internal registers shows that the tuning command (CMD19)
has failed.
The freeze is then due to the delay block involved in the tuning sequence.
To correct this, clear the delay block register DLYB_CR register after
the tuning commands.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 1103f807 ("mmc: mmci_sdmmc: Add execute tuning with delay block")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211215141727.4901-4-yann.gautier@foss.st.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Although this compatible is not used in kernel, as we use the common
MMCI driver, it is used by bootloaders. The U-Boot driver was merged
before the kernel driver and uses this compatible.

To avoid issues when aligning device tree files between kernel and
boot loader, the ST dedicated compatible is added to bindings file.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211210091834.28958-1-yann.gautier@foss.st.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Remove MESON_SDHC_NUM_BUILTIN_CLKS because it is not used anywhere in
the driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211219153442.463863-3-martin.blumenstingl@googlemail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.

This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
  brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
                          BCM43362/1
  brcmf_sdiod_ramrw: membytes transfer failed
  brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
                                 at 0x00000000
  brcmf_sdio_download_firmware: dongle image file download failed

And with this change:
  brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
                          BCM43362/1
  brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
                            have limited channels available
  brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
                         version 5.90.195.89.6 FWID 01-b30a427d

Fixes: e4bf1b09 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211219153442.463863-2-martin.blumenstingl@googlemail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It's seems prone to problems by allowing card detect and its corresponding
mmc_rescan() work to run, during platform shutdown. For example, we may end
up turning off the power while initializing a card, which potentially could
damage it.

To avoid this scenario, let's add ->shutdown_pre() callback for the mmc host
class device and then turn of the card detect from there.
Reported-by: Al Cooper <alcooperx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211203141555.105351-1-ulf.hansson@linaro.org

Convert the Broadcom STB SDHCI controller Device Tree binding to YAML.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211208003727.3596577-2-f.fainelli@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If there is no driver match function, the driver core assumes that each
candidate pair (driver, device) matches, see driver_match_device().

Drop the mmc bus's match function that always returned 1 and so implements
the same behaviour as when there is no match function.
Signed-off-by: lizhe <sensor1010@163.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211207095029.96387-1-sensor1010@163.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When 'unevaluatedProperties' support is enabled, the following warnings
are generated in the mmc bindings:

Documentation/devicetree/bindings/mmc/mtk-sd.example.dt.yaml: mmc@11230000: Unevaluated properties are not allowed ('reg', 'interrupts' were unexpected)
Documentation/devicetree/bindings/mmc/sdhci-am654.example.dt.yaml: mmc@4f80000: Unevaluated properties are not allowed ('sdhci-caps-mask' was unexpected)
Documentation/devicetree/bindings/mmc/socionext,uniphier-sd.example.dt.yaml: mmc@5a400000: Unevaluated properties are not allowed ('dma-names', 'dmas' were unexpected)
Documentation/devicetree/bindings/mmc/arm,pl18x.example.dt.yaml: mmc@80126000: Unevaluated properties are not allowed ('dmas', 'dma-names' were unexpected)
Documentation/devicetree/bindings/mmc/arasan,sdhci.example.dt.yaml: mmc@80420000: Unevaluated properties are not allowed ('resets' was unexpected)
Documentation/devicetree/bindings/mmc/arm,pl18x.example.dt.yaml: mmc@52007000: Unevaluated properties are not allowed ('interrupt-names' was unexpected)
Documentation/devicetree/bindings/clock/imx8qxp-lpcg.example.dt.yaml: mmc@5b010000: Unevaluated properties are not allowed ('power-domains' was unexpected)

Add the missing properties as necessary. For pl18x, drop interrupt-names
as there isn't any use of it when there are 2 interrupts.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Chaotian Jing <chaotian.jing@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Wenbin Mei <wenbin.mei@mediatek.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211206174201.2297265-1-robh@kernel.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use write_or_read temporary variable in mmc_spi_data_do() to deduplicate
the conditional code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211206115218.73874-2-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Convert 'multiple' to be boolean in mmc_spi_data_do() since
it's initially being used as boolean.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211206115218.73874-1-andriy.shevchenko@linux.intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for i.MXRT1050's sdhc.

Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20211125211443.1150135-12-Mr.Bossman075@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add i.MXRT documentation for compatible string.

Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211125211443.1150135-11-Mr.Bossman075@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Move the common MMC_CAP_CMD23 capability to common_caps so that only the
special case of MMC_CAP_1_8V_DDR and MMC_CAP_8_BIT_DATA are set via
caps/num_caps.  Both of those can, and should, be set via device tree
properties instead, so we can now say that exynos_dwmmc_caps is only
used for backwards compatibility.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211124184603.3897245-5-john@metanate.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The capabilities for all instances are the same, so use common_caps
instead of caps/num_caps to remove the dependency on the mshcN device
tree alias.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211124184603.3897245-4-john@metanate.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The capabilities for all instances are the same, so use common_caps
instead of caps/num_caps to remove the dependency on the mshcN device
tree alias.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211124184603.3897245-3-john@metanate.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The caps field depends on the mshcN alias ID but for some devices this
is unnecessary as the capabilities are the same for all instances
sharing the same compatible.

Add a common_caps field for this case which updates the host's
capabilities without needing the mshcN alias ID.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211124184603.3897245-2-john@metanate.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add PCI ID for Intel ADL eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211124094850.1783220-1-adrian.hunter@intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The TMOUT register is always set with a full value for every transfer,
which (with a 200MHz clock) will give a full DRTO of ~84 milliseconds.
This is normally good enough to complete the request, but setting a full
value makes it impossible to test shorter timeouts, when for example
testing data read times on different SD cards.

Add a function to set any value smaller than the maximum of 0xFFFFFF.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20211119155337.14341-1-marten.lindahl@axis.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In mmc_send_op_cond(), loops are continuously performed at the same
interval of 10 ms.  However the behaviour is not good for some eMMC
which can be out from a busy state earlier than 10 ms if normal.

Rather than fixing about the interval time in mmc_send_op_cond(),
let's instead convert into using the common __mmc_poll_for_busy().

The reason for adjusting the interval time is that it is important
to reduce the eMMC initialization time, especially in devices that
use eMMC as rootfs.

Test log(eMMC:KLM8G1GETF-B041):

before: 12 ms (0.311016 - 0.298729)
[    0.295823] mmc0: starting CMD0 arg 00000000 flags 000000c0
[    0.298729] mmc0: starting CMD1 arg 40000080 flags 000000e1<-start
[    0.311016] mmc0: starting CMD1 arg 40000080 flags 000000e1<-finish
[    0.311336] mmc0: starting CMD2 arg 00000000 flags 00000007

after: 2 ms (0.301270 - 0.298762)
[    0.295862] mmc0: starting CMD0 arg 00000000 flags 000000c0
[    0.298762] mmc0: starting CMD1 arg 40000080 flags 000000e1<-start
[    0.299067] mmc0: starting CMD1 arg 40000080 flags 000000e1
[    0.299441] mmc0: starting CMD1 arg 40000080 flags 000000e1
[    0.299879] mmc0: starting CMD1 arg 40000080 flags 000000e1
[    0.300446] mmc0: starting CMD1 arg 40000080 flags 000000e1
[    0.301270] mmc0: starting CMD1 arg 40000080 flags 000000e1<-finish
[    0.301572] mmc0: starting CMD2 arg 00000000 flags 00000007
Signed-off-by: Huijin Park <huijin.park@samsung.com>
Link: https://lore.kernel.org/r/20211104063231.2115-3-huijin.park@samsung.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch changes the __mmc_poll_for_busy() first parameter type
from 'struct mmc_card*' to 'struct mmc_host*'.
Because the function refers only 'struct mmc_host' to get hostname.
Signed-off-by: Huijin Park <huijin.park@samsung.com>
Link: https://lore.kernel.org/r/20211104063231.2115-2-huijin.park@samsung.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The USDHC on i.MX8ULP is derived from i.MX8MM, it uses two
compatible strings, so update the compatible string for i.MX8ULP.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20211112082930.3809351-3-peng.fan@oss.nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If we get a data error during a block transfer command, a stop command
(CMD12) is normally initiated. But this does not work for the general
command (CMD56), but instead the action is ignored and an uninitialized
command struct is used for the stop action, with unexpected result.

Fix this by adding a check for GEN_CMD when preparing stop transmission.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20211103182716.28419-1-marten.lindahl@axis.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Due to recent changes to the mmc core, card quirks can be applied based
upon a compatible string in child OF node. The quirk needed for wl1251
(SDIO card) is managed in the core, therefore there is no longer any reason
to deal with this in omap_hsmmc too, so let's remove it.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/77d313b97d1e18b0eb7ed2d88d718d960f329bb0.1636564631.git.hns@goldelico.com
[Ulf: Re-wrote the commit message to make it more clear]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The TiWi WL1251 WiFi chip needs special setup of the sdio
interface before it can be probed.

So far, this is done in omap_hsmmc_init_card() in omap_hsmmc.c
which makes it useable only if connected to omap devices
which use the omap_hsmmc. The OpenPandora is the most promient
example.

There are plans to switch to a newer sdhci-omap driver and
retire omap_hsmmc. Hence this quirk must be reworked or moved
somewhere else. Ideally to some location that is not dependent
on the specific SoC mmc host driver.

This is achieved by the new mmc_fixup_device() option introduced
by ("mmc: allow to match the device tree to apply quirks") to match
through device tree compatible string.

This quirk will be called early right after where host->ops->init_card()
and thus omap_hsmmc_init_card() was previously called.

Note that we do not need to transplant

	card->ocr = 0x80;

because we rely on ("mmc: core: Fixup storing of OCR for MMC_QUIRK_NONSTD_SDIO").
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/774565df7f02124c003aaf8b879706352548f832.1636564631.git.hns@goldelico.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.

In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.

To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This (initially empty) table allows to match quirks early based
on .compatible of the child node of some mmc/sdio interface.

This allows to add quirks based on device tree instead of having
card specific code in the host ops.

A new macro SDIO_FIXUP_COMPATIBLE makes the definition readable.

And we call mmc_fixup_device(sdio_card_init_methods) just after
where host->ops->init_card() can be optionally called.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/b13fd8b3eebc3c23b6816b254a518c224cbdcfd4.1636564631.git.hns@goldelico.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MMC subsystem provides a way to apply quirks when a device match some
properties (VID, PID, etc...) Unfortunately, some SDIO devices do not
comply with the SDIO specification and does not provide reliable VID/PID
(eg. Silabs WF200).

So, the drivers for these devices rely on device tree to identify the
device.

This patch allows the MMC to also rely on the device tree to apply a
quirk.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/9e68e3d23e62a78527aabc1281f89e15200c7d09.1636564631.git.hns@goldelico.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Currently, mmc_fixup_device() is a bit difficult to read because of
particularly long condition.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/6515c1e8b3aa69ad273726f6e877d85c20f286ad.1636564631.git.hns@goldelico.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Refactor the code so that card detect irqs are always reenabled after a
reset. This avoids doing it manually all over the code or forgetting to
do this in the future.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
[wsa: added a comment when 'native_hotplug' has to be set]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211103122646.64422-1-wsa+renesas@sang-engineering.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When CMD13 is sent after switching to HS400ES mode, the bus
is operating at either MMC_HIGH_26_MAX_DTR or MMC_HIGH_52_MAX_DTR.
To meet Tegra SDHCI requirement at HS400ES mode, force SDHCI
interface clock to MMC_HS200_MAX_DTR (200 MHz) so that host
controller CAR clock and the interface clock are rate matched.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: dfc9700c ("mmc: tegra: Implement HS400 enhanced strobe")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211214113653.4631-1-pshete@nvidia.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 5.16-rc5.  They include:

   - gadget driver fixes for reported issues

   - xhci fixes for reported problems.

   - config endpoint parsing fixes for where we got bitfields wrong

  Most of these have been in linux-next, the remaining few were not, but
  got lots of local testing in my systems and in some cloud testing
  infrastructures"

* tag 'usb-5.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: core: config: using bit mask instead of individual bits
  usb: core: config: fix validation of wMaxPacketValue entries
  USB: gadget: zero allocate endpoint 0 buffers
  USB: gadget: detect too-big endpoint 0 requests
  xhci: avoid race between disable slot command and host runtime suspend
  xhci: Remove CONFIG_USB_DEFAULT_PERSIST to prevent xHCI from runtime suspending
  Revert "usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default"

Pull char/misc driver fixes from Greg KH:
 "Here are a bunch of small char/misc and other driver subsystem fixes.

  Included in here are:

   - iio driver fixes for reported problems

   - phy driver fixes for a number of reported problems

   - mhi resume bugfix for broken hardware

   - nvmem driver fix

   - rtsx driver fix for irq issues

   - fastrpc packet parsing fix

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (33 commits)
  bus: mhi: core: Add support for forced PM resume
  iio: trigger: stm32-timer: fix MODULE_ALIAS
  misc: rtsx: Avoid mangling IRQ during runtime PM
  nvmem: eeprom: at25: fix FRAM byte_len
  misc: fastrpc: fix improper packet size calculation
  MAINTAINERS: add maintainer for Qualcomm FastRPC driver
  bus: mhi: pci_generic: Fix device recovery failed issue
  iio: adc: stm32: fix null pointer on defer_probe error
  phy: HiSilicon: Fix copy and paste bug in error handling
  dt-bindings: phy: zynqmp-psgtr: fix USB phy name
  phy: ti: omap-usb2: Fix the kernel-doc style
  phy: qualcomm: ipq806x-usb: Fix kernel-doc style
  iio: at91-sama5d2: Fix incorrect sign extension
  iio: adc: axp20x_adc: fix charging current reporting on AXP22x
  iio: gyro: adxrs290: fix data signedness
  phy: ti: tusb1210: Fix the kernel-doc warn
  phy: qualcomm: usb-hsic: Fix the kernel-doc warn
  phy: qualcomm: qmp: Add missing struct documentation
  phy: mvebu-cp110-utmi: Fix kernel-doc warns
  iio: ad7768-1: Call iio_trigger_notify_done() on error
  ...

Pull timer fixes from Thomas Gleixner:
 "Two fixes for clock chip drivers:

   - A regression fix for the Designware APB timer. A recent change to
     the error checking code transformed the error condition wrongly so
     it turned into a fail if good condition.

   - Fix a clang build fail of the ARM architected timer driver"

* tag 'timers-urgent-2021-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/arm_arch_timer: Force inlining of erratum_set_next_event_generic()
  clocksource/drivers/dw_apb_timer_of: Fix probe failure

Pull irq fixes from Thomas Gleixner:
 "A set of interrupt chip driver fixes:

   - Fix the multi vector MSI allocation on Armada 370XP

   - Do interrupt acknowledgement correctly in the aspeed-scu driver

   - Make the IPR register offset correct in the NVIC driver

   - Make redistribution table flushing correct by issueing a SYNC
     command to ensure that the invalidation command has been executed

   - Plug a device tree node reference leak in the bcm7210-l2 driver

   - Trivial fixes in the MIPS GIC and the Apple AIC drivers"

* tag 'irq-urgent-2021-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-bcm7120-l2: Add put_device() after of_find_device_by_node()
  irqchip/irq-gic-v3-its.c: Force synchronisation when issuing INVALL
  irqchip/apple-aic: Mark aic_init_smp() as __init
  irqchip: nvic: Fix offset for Interrupt Priority Offsets
  irqchip/mips-gic: Use bitfield helpers
  irqchip/aspeed-scu: Replace update_bits with write_bits.
  irqchip/armada-370-xp: Fix support for Multi-MSI interrupts
  irqchip/armada-370-xp: Fix return value of armada_370_xp_msi_alloc()

Pull scheduler fix from Thomas Gleixner:
 "A single fix for the x86 scheduler topology:

  Using cluster topology on hybrid CPUs, e.g. Alder Lake, biases the
  scheduler towards the ATOM cluster as that has more total capacity.
  Use selection based on CPU priority instead"

* tag 'sched-urgent-2021-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched,x86: Don't use cluster topology for x86 hybrid CPUs