- 13 Mar, 2017 8 commits
-
-
Paul Burton authored
commit 67c75057 upstream. is_jump_ins() checks 16b instruction fields without verifying that the instruction is indeed 16b, as is done by is_ra_save_ins() & is_sp_move_ins(). Add the appropriate check. Signed-off-by:
Paul Burton <paul.burton@imgtec.com> Fixes: 34c2f668 ("MIPS: microMIPS: Add unaligned access support.") Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/14531/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Paul Burton authored
commit b6c7a324 upstream. get_frame_info() is meant to iterate over up to the first 128 instructions within a function, but for microMIPS kernels it will not reach that many instructions unless the function is 512 bytes long since we calculate the maximum number of instructions to check by dividing the function length by the 4 byte size of a union mips_instruction. In microMIPS kernels this won't do since instructions are variable length. Fix this by instead checking whether the pointer to the current instruction has reached the end of the function, and use max_insns as a simple constant to check the number of iterations against. Signed-off-by:
-
Paul Burton authored
commit a3552dac upstream. During stack unwinding we call a number of functions to determine what type of instruction we're looking at. The union mips_instruction pointer provided to them may be pointing at a 2 byte, but not 4 byte, aligned address & we thus cannot directly access the 4 byte wide members of the union mips_instruction. To avoid this is_ra_save_ins() copies the required half-words of the microMIPS instruction to a correctly aligned union mips_instruction on the stack, which it can then access safely. The is_jump_ins() & is_sp_move_ins() functions do not correctly perform this temporary copy, and instead attempt to directly dereference 4 byte fields which may be misaligned and lead to an address exception. Fix this by copying the instruction halfwords to a temporary union mips_instruction in get_frame_info() such that we can provide a 4 byte aligned union mips_instruction to the is_*_ins() functions and they do not need to deal with misalignment themselves. Signed-off-by:
-
Paul Burton authored
commit ccaf7caf upstream. get_frame_info() can be called in microMIPS kernels with the ISA bit already clear. For example this happens when unwind_stack_by_address() is called because we begin with a PC that has the ISA bit set & subtract the (odd) offset from the preceding symbol (which does not have the ISA bit set). Since get_frame_info() unconditionally subtracts 1 from the PC in microMIPS kernels it incorrectly misaligns the address it then attempts to access code at, leading to an address error exception. Fix this by using msk_isa16_mode() to clear the ISA bit, which allows get_frame_info() to function regardless of whether it is provided with a PC that has the ISA bit set or not. Signed-off-by:
-
James Cowgill authored
commit 884b4269 upstream. If copy_from_user is called with a large buffer (>= 128 bytes) and the userspace buffer refers partially to unreadable memory, then it is possible for Octeon's copy_from_user to report the wrong number of bytes have been copied. In the case where the buffer size is an exact multiple of 128 and the fault occurs in the last 64 bytes, copy_from_user will report that all the bytes were copied successfully but leave some garbage in the destination buffer. The bug is in the main __copy_user_common loop in octeon-memcpy.S where in the middle of the loop, src and dst are incremented by 128 bytes. The l_exc_copy fault handler is used after this but that assumes that "src < THREAD_BUADDR($28)". This is not the case if src has already been incremented. Fix by adding an extra fault handler which rewinds the src and dst pointers 128 bytes before falling though to l_exc_copy. Thanks to the pwritev test from the strace test suite for originally highlighting this bug! Fixes: 5b3b1688 ("MIPS: Add Cavium OCTEON processor support ...") Signed-off-by:
James Cowgill <James.Cowgill@imgtec.com> Acked-by:
David Daney <david.daney@cavium.com> Reviewed-by:
James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/14978/Signed-off-by:
-
Ralf Baechle authored
commit 66fd848c upstream. For certain arguments such as saddr = 0xc0a8fd60, daddr = 0xc0a8fda1, len = 80, proto = 17, sum = 0x7eae049d there will be a carry when folding the intermediate 64 bit checksum to 32 bit but the code doesn't add the carry back to the one's complement sum, thus an incorrect result will be generated. Reported-by:
Mark Zhang <bomb.zhang@gmail.com> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
commit ecf1e225 upstream. Instead of the one when another syscall takes place while another is being processed (in another CPU, but we show it serialized, so need to "interrupt" the other), and also when finally showing the sys_enter + sys_exit + duration, where we were showing the sample->time for the sys_exit, duh. Before: # perf trace sleep 1 <SNIP> 0.373 ( 0.001 ms): close(fd: 3 ) = 0 1000.626 (1000.211 ms): nanosleep(rqtp: 0x7ffd6ddddfb0) = 0 1000.653 ( 0.003 ms): close(fd: 1 ) = 0 1000.657 ( 0.002 ms): close(fd: 2 ) = 0 1000.667 ( 0.000 ms): exit_group( ) # After: # perf trace sleep 1 <SNIP> 0.336 ( 0.001 ms): close(fd: 3 ) = 0 0.373 (1000.086 ms): nanosleep(rqtp: 0x7ffe303e9550) = 0 1000.481 ( 0.002 ms): close(fd: 1 ) = 0 1000.485 ( 0.001 ms): close(fd: 2 ) = 0 1000.494 ( 0.000 ms): exit_group( ) [root@jouet linux]# [js] no trace__printf_interrupted_entry in 3.12 yet Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/n/tip-ecbzgmu2ni6glc6zkw8p1zmx@git.kernel.org Fixes: 752fde44 ("perf trace: Support interrupted syscalls") Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Shmulik Ladkani authored
commit d65f2fa6 upstream. META_COLLECTOR int_vlan_tag() assumes that if the accel tag (vlan_tci) is zero, then no vlan accel tag is present. This is incorrect for zero VID vlan accel packets, making the following match fail: tc filter add ... basic match 'meta(vlan mask 0xfff eq 0)' ... Apparently 'int_vlan_tag' was implemented prior VLAN_TAG_PRESENT was introduced in 05423b24 "vlan: allow null VLAN ID to be used" (and at time introduced, the 'vlan_tx_tag_get' call in em_meta was not adapted). Fix, testing skb_vlan_tag_present instead of testing skb_vlan_tag_get's value. Fixes: 05423b24 ("vlan: allow null VLAN ID to be used") Fixes: 1a31f204 ("netsched: Allow meta match on vlan tag on receive") Signed-off-by:
Shmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
- 11 Mar, 2017 2 commits
-
-
Marcelo Ricardo Leitner authored
commit dfcb9f4f upstream. commit 2dcab598 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf") attempted to avoid a BUG_ON call when the association being used for a sendmsg() is blocked waiting for more sndbuf and another thread did a peeloff operation on such asoc, moving it to another socket. As Ben Hutchings noticed, then in such case it would return without locking back the socket and would cause two unlocks in a row. Further analysis also revealed that it could allow a double free if the application managed to peeloff the asoc that is created during the sendmsg call, because then sctp_sendmsg() would try to free the asoc that was created only for that call. This patch takes another approach. It will deny the peeloff operation if there is a thread sleeping on the asoc, so this situation doesn't exist anymore. This avoids the issues described above and also honors the syscalls that are already being handled (it can be multiple sendmsg calls). Joint work with Xin Long. Fixes: 2dcab598 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf") Cc: Alexander Popov <alex.popov@linux.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
colyli@suse.de authored
commit 03a9e24e upstream. Recently I receive a bug report that on Linux v3.0 based kerenl, hot add disk to a md linear device causes kernel crash at linear_congested(). From the crash image analysis, I find in linear_congested(), mddev->raid_disks contains value N, but conf->disks[] only has N-1 pointers available. Then a NULL pointer deference crashes the kernel. There is a race between linear_add() and linear_congested(), RCU stuffs used in these two functions cannot avoid the race. Since Linuv v4.0 RCU code is replaced by introducing mddev_suspend(). After checking the upstream code, it seems linear_congested() is not called in generic_make_request() code patch, so mddev_suspend() cannot provent it from being called. The possible race still exists. Here I explain how the race still exists in current code. For a machine has many CPUs, on one CPU, linear_add() is called to add a hard disk to a md linear device; at the same time on other CPU, linear_congested() is called to detect whether this md linear device is congested before issuing an I/O request onto it. Now I use a possible code execution time sequence to demo how the possible race happens, seq linear_add() linear_congested() 0 conf=mddev->private 1 oldconf=mddev->private 2 mddev->raid_disks++ 3 for (i=0; i<mddev->raid_disks;i++) 4 bdev_get_queue(conf->disks[i].rdev->bdev) 5 mddev->private=newconf In linear_add() mddev->raid_disks is increased in time seq 2, and on another CPU in linear_congested() the for-loop iterates conf->disks[i] by the increased mddev->raid_disks in time seq 3,4. But conf with one more element (which is a pointer to struct dev_info type) to conf->disks[] is not updated yet, accessing its structure member in time seq 4 will cause a NULL pointer deference fault. To fix this race, there are 2 parts of modification in the patch, 1) Add 'int raid_disks' in struct linear_conf, as a copy of mddev->raid_disks. It is initialized in linear_conf(), always being consistent with pointers number of 'struct dev_info disks[]'. When iterating conf->disks[] in linear_congested(), use conf->raid_disks to replace mddev->raid_disks in the for-loop, then NULL pointer deference will not happen again. 2) RCU stuffs are back again, and use kfree_rcu() in linear_add() to free oldconf memory. Because oldconf may be referenced as mddev->private in linear_congested(), kfree_rcu() makes sure that its memory will not be released until no one uses it any more. Also some code comments are added in this patch, to make this modification to be easier understandable. This patch can be applied for kernels since v4.0 after commit: 3be260cc ("md/linear: remove rcu protections in favour of suspend/resume"). But this bug is reported on Linux v3.0 based kernel, for people who maintain kernels before Linux v4.0, they need to do some back back port to this patch. Changelog: - V3: add 'int raid_disks' in struct linear_conf, and use kfree_rcu() to replace rcu_call() in linear_add(). - v2: add RCU stuffs by suggestion from Shaohua and Neil. - v1: initial effort. Signed-off-by:
Coly Li <colyli@suse.de> Cc: Shaohua Li <shli@fb.com> Cc: Neil Brown <neilb@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
- 06 Mar, 2017 1 commit
-
-
Jiri Slaby authored
-
- 03 Mar, 2017 24 commits
-
-
Johan Hovold authored
commit 8727bf68 upstream. Fix errors during open not being returned to userspace. Specifically, failed control-line manipulations or control or read urb submissions would not be detected. Fixes: 7fb57a01 ("USB: cdc-acm: Fix potential deadlock (lockdep warning)") Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Johan Hovold authored
commit 703df329 upstream. We must not do the usb_autopm_put_interface() before submitting the read urbs or we might end up doing I/O to a suspended device. Fixes: 088c64f8 ("USB: cdc-acm: re-write read processing") Signed-off-by:
-
Alexey Khoroshilov authored
commit 070c0b17 upstream. If acm_submit_read_urbs() fails in acm_port_activate(), error handling code calls usb_autopm_put_interface() while it is already called before acm_submit_read_urbs(). The patch reorganizes error handling code to avoid double decrement of USB interface's PM-usage counter. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by:
Oliver Neukum <oliver@neukum.org> Signed-off-by:
-
Heiko Carstens authored
commit e84d2f8d upstream. This is the s390 variant of Alexei's JIT bug fix. (patch description below stolen from Alexei's patch) bpf_alloc_binary() adds 128 bytes of room to JITed program image and rounds it up to the nearest page size. If image size is close to page size (like 4000), it is rounded to two pages: round_up(4000 + 4 + 128) == 8192 then 'hole' is computed as 8192 - (4000 + 4) = 4188 If prandom_u32() % hole selects a number >= PAGE_SIZE - sizeof(*header) then kernel will crash during bpf_jit_free(): kernel BUG at arch/x86/mm/pageattr.c:887! Call Trace: [<ffffffff81037285>] change_page_attr_set_clr+0x135/0x460 [<ffffffff81694cc0>] ? _raw_spin_unlock_irq+0x30/0x50 [<ffffffff810378ff>] set_memory_rw+0x2f/0x40 [<ffffffffa01a0d8d>] bpf_jit_free_deferred+0x2d/0x60 [<ffffffff8106bf98>] process_one_work+0x1d8/0x6a0 [<ffffffff8106bf38>] ? process_one_work+0x178/0x6a0 [<ffffffff8106c90c>] worker_thread+0x11c/0x370 since bpf_jit_free() does: unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK; struct bpf_binary_header *header = (void *)addr; to compute start address of 'bpf_binary_header' and header->pages will pass junk to: set_memory_rw(addr, header->pages); Fix it by making sure that &header->image[prandom_u32() % hole] and &header are in the same page. Fixes: aa2d2c73 ("s390/bpf,jit: address randomize and write protect jit code") Reported-by:
Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
Alexei Starovoitov authored
commit 773cd38f upstream. bpf_alloc_binary() adds 128 bytes of room to JITed program image and rounds it up to the nearest page size. If image size is close to page size (like 4000), it is rounded to two pages: round_up(4000 + 4 + 128) == 8192 then 'hole' is computed as 8192 - (4000 + 4) = 4188 If prandom_u32() % hole selects a number >= PAGE_SIZE - sizeof(*header) then kernel will crash during bpf_jit_free(): kernel BUG at arch/x86/mm/pageattr.c:887! Call Trace: [<ffffffff81037285>] change_page_attr_set_clr+0x135/0x460 [<ffffffff81694cc0>] ? _raw_spin_unlock_irq+0x30/0x50 [<ffffffff810378ff>] set_memory_rw+0x2f/0x40 [<ffffffffa01a0d8d>] bpf_jit_free_deferred+0x2d/0x60 [<ffffffff8106bf98>] process_one_work+0x1d8/0x6a0 [<ffffffff8106bf38>] ? process_one_work+0x178/0x6a0 [<ffffffff8106c90c>] worker_thread+0x11c/0x370 since bpf_jit_free() does: unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK; struct bpf_binary_header *header = (void *)addr; to compute start address of 'bpf_binary_header' and header->pages will pass junk to: set_memory_rw(addr, header->pages); Fix it by making sure that &header->image[prandom_u32() % hole] and &header are in the same page Fixes: 314beb9b ("x86: bpf_jit_comp: secure bpf jit against spraying attacks") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Claudiu Manoil authored
commit 98a46d46 upstream. This fixes a seg fault on 'ethtool -A' entry if the interface is down. Obviously we need to have the phy device initialized / "connected" (see of_phy_connect()) to be able to advertise pause frame capabilities. Fixes: 23402bddSigned-off-by:
Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by:
-
Thomas Petazzoni authored
commit 398f5d5e upstream. MBus windows are used on Marvell platforms to map certain peripherals in the physical address space. In the PCIe context, MBus windows are needed to map PCIe I/O and memory regions in the physical address. However, those MBus windows can only have power of two sizes, while PCIe BAR do not necessarily guarantee this. For this reason, the current pci-mvebu breaks on platforms where PCIe devices have BARs that don't sum up to a power of two size at the emulated bridge level. This commit fixes this by allowing the pci-mvebu driver to create multiple contiguous MBus windows (each having a power of two size) to cover a given PCIe BAR. To achieve this, two functions are added: mvebu_pcie_add_windows() and mvebu_pcie_del_windows() to respectively add and remove all the MBus windows that are needed to map the provided PCIe region base and size. The emulated PCI bridge code now calls those functions, instead of directly calling the mvebu-mbus driver functions. Fixes: 45361a4f ('pci: PCIe driver for Marvell Armada 370/XP systems') Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Link: https://lkml.kernel.org/r/1397823593-1932-8-git-send-email-thomas.petazzoni@free-electrons.comTested-by:
Neil Greatorex <neil@fatboyfat.co.uk> Acked-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
-
Jingoo Han authored
commit 06489002 upstream. Use max_t() instead of max(resource_size_t,) in order to fix the following checkpatch warning. WARNING: max() should probably be max_t(resource_size_t, SZ_64K, size) WARNING: max() should probably be max_t(resource_size_t, SZ_1M, size) Signed-off-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
-
Steffen Klassert authored
commit a3245236 upstream. We currently count the size of LL_MAX_HEADER and struct iphdr twice for vti4 devices, this leads to a wrong device mtu. The size of LL_MAX_HEADER and struct iphdr is already counted in ip_tunnel_bind_dev(), so don't do it again in vti_tunnel_init(). Fixes: b9959fd3 ("vti: switch to new ip tunnel code") Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Daniel Borkmann authored
commit 4c47af4d upstream. Problem statement: 1) both paths (primary path1 and alternate path2) are up after the association has been established i.e., HB packets are normally exchanged, 2) path2 gets inactive after path_max_retrans * max_rto timed out (i.e. path2 is down completely), 3) now, if a transmission times out on the only surviving/active path1 (any ~1sec network service impact could cause this like a channel bonding failover), then the retransmitted packets are sent over the inactive path2; this happens with partial failover and without it. Besides not being optimal in the above scenario, a small failure or timeout in the only existing path has the potential to cause long delays in the retransmission (depending on RTO_MAX) until the still active path is reselected. Further, when the T3-timeout occurs, we have active_patch == retrans_path, and even though the timeout occurred on the initial transmission of data, not a retransmit, we end up updating retransmit path. RFC4960, section 6.4. "Multi-Homed SCTP Endpoints" states under 6.4.1. "Failover from an Inactive Destination Address" the following: Some of the transport addresses of a multi-homed SCTP endpoint may become inactive due to either the occurrence of certain error conditions (see Section 8.2) or adjustments from the SCTP user. When there is outbound data to send and the primary path becomes inactive (e.g., due to failures), or where the SCTP user explicitly requests to send data to an inactive destination transport address, before reporting an error to its ULP, the SCTP endpoint should try to send the data to an alternate __active__ destination transport address if one exists. When retransmitting data that timed out, if the endpoint is multihomed, it should consider each source-destination address pair in its retransmission selection policy. When retransmitting timed-out data, the endpoint should attempt to pick the most divergent source-destination pair from the original source-destination pair to which the packet was transmitted. Note: Rules for picking the most divergent source-destination pair are an implementation decision and are not specified within this document. So, we should first reconsider to take the current active retransmission transport if we cannot find an alternative active one. If all of that fails, we can still round robin through unkown, partial failover, and inactive ones in the hope to find something still suitable. Commit 4141ddc0 ("sctp: retran_path update bug fix") broke that behaviour by selecting the next inactive transport when no other active transport was found besides the current assoc's peer.retran_path. Before commit 4141ddc0, we would have traversed through the list until we reach our peer.retran_path again, and in case that is still in state SCTP_ACTIVE, we would take it and return. Only if that is not the case either, we take the next inactive transport. Besides all that, another issue is that transports in state SCTP_UNKNOWN could be preferred over transports in state SCTP_ACTIVE in case a SCTP_ACTIVE transport appears after SCTP_UNKNOWN in the transport list yielding a weaker transport state to be used in retransmission. This patch mostly reverts 4141ddc0, but also rewrites this function to introduce more clarity and strictness into the code. A strict priority of transport states is enforced in this patch, hence selection is active > unkown > partial failover > inactive. Fixes: 4141ddc0 ("sctp: retran_path update bug fix") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Cc: Gui Jianfeng <guijianfeng@cn.fujitsu.com> Acked-by:
Vlad Yasevich <yasevich@gmail.com> Signed-off-by:
-
Hannes Frederic Sowa authored
commit 11ffff75 upstream. In commit 1ec047eb ("ipv6: introduce per-interface counter for dad-completed ipv6 addresses") I build the detection of the first operational link-local address much to complex. Additionally this code now has a race condition. Replace it with a much simpler variant, which just scans the address list when duplicate address detection completes, to check if this is the first valid link local address and send RS and MLD reports then. Fixes: 1ec047eb ("ipv6: introduce per-interface counter for dad-completed ipv6 addresses") Reported-by:
Jiri Pirko <jiri@resnulli.us> Cc: Flavio Leitner <fbl@redhat.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by:
Flavio Leitner <fbl@redhat.com> Acked-by:
-
Daniel Borkmann authored
commit 965801e1 upstream. In function lowpan_header_create(), we invoke the following code construct: struct ipv6hdr *hdr; ... hdr = ipv6_hdr(skb); ... if (...) memcpy(hc06_ptr + 1, &hdr->flow_lbl[1], 2); else memcpy(hc06_ptr, &hdr, 4); Where the else path of the condition, that is, non-compression path, calls memcpy() with a pointer to struct ipv6hdr *hdr as source, thus two levels of indirection. This cannot be correct, and likely only one level of pointer was intended as source buffer for memcpy() here. Fixes: 44331fe2 ("IEEE802.15.4: 6LoWPAN basic support") Signed-off-by:
-
Li RongQing authored
commit abb6013c upstream. when read/write the 64bit data, the correct lock should be hold. Fixes: 87b6d218 ("tunnel: implement 64 bits statistics") Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
Li RongQing <roy.qing.li@gmail.com> Signed-off-by:
-
Viresh Kumar authored
commit 08fd8c1c upstream. Prevent __cpufreq_add_dev() from overwriting the existing values of user_policy.{min|max|policy|governor} with defaults during resume from system suspend. Fixes: 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume") Reported-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> [rjw: Changelog] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit 72368d12 upstream. If cpufreq_policy_restore() returns NULL during system resume, __cpufreq_add_dev() should just fall back to the full initialization instead of returning an error, because that may actually make things work. Moreover, it should not leave stale fallback data behind after it has failed to restore a previously existing policy. This change is based on Viresh Kumar's work. Fixes: 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume") Reported-by:
-
Viresh Kumar authored
commit 42f921a6 upstream. There are cases where cpufreq_add_dev() may fail for some CPUs during system resume. With the current code we will still have sysfs cpufreq files for those CPUs and struct cpufreq_policy would be already freed for them. Hence any operation on those sysfs files would result in kernel warnings. Example of problems resulting from resume errors (from Bjørn Mork): WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212() missing sysfs attribute operations for kobject: (null) Modules linked in: [stripped as irrelevant] CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153 Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011 0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006 ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000 ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310 Call Trace: [<ffffffff81380b0e>] dump_stack+0x55/0x76 [<ffffffff81038635>] warn_slowpath_common+0x7c/0x96 [<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212 [<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43 [<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82 [<ffffffff81182382>] ? sysfs_open_file+0x32/0x212 [<ffffffff811823c7>] sysfs_open_file+0x77/0x212 [<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac [<ffffffff81122562>] do_dentry_open+0x17c/0x257 [<ffffffff8112267e>] finish_open+0x41/0x4f [<ffffffff81130225>] do_last+0x80c/0x9ba [<ffffffff8112dbbd>] ? inode_permission+0x40/0x42 [<ffffffff81130606>] path_openat+0x233/0x4a1 [<ffffffff81130b7e>] do_filp_open+0x35/0x85 [<ffffffff8113b787>] ? __alloc_fd+0x172/0x184 [<ffffffff811232ea>] do_sys_open+0x6b/0xfa [<ffffffff811233a7>] SyS_openat+0xf/0x11 [<ffffffff8138c812>] system_call_fastpath+0x16/0x1b To fix this, remove those sysfs files or put the associated kobject in case of such errors. Also, to make it simple, remove the cpufreq sysfs links from all the CPUs (except for the policy->cpu) during suspend, as that operation won't result in a loss of sysfs file permissions and we can create those links during resume just fine. [js] no rwsem in 3.12 yet Fixes: 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume") Reported-and-tested-by:
-
Bjørn Mork authored
commit 2167e239 upstream. This is effectively a revert of commit 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume"), which enabled suspend/resume optimizations leaving the sysfs files in place. Errors during suspend/resume are not handled properly, leaving dead sysfs attributes in case of failures. There are are number of functions with special code for the "frozen" case, and all these need to also have special error handling. The problem is easy to demonstrate by making cpufreq_driver->init() or cpufreq_driver->get() fail during resume. The code is too complex for a simple fix, with split code paths in multiple blocks within a number of functions. It is therefore best to revert the patch enabling this code until the error handling is in place. Examples of problems resulting from resume errors: WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212() missing sysfs attribute operations for kobject: (null) Modules linked in: [stripped as irrelevant] CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153 Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011 0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006 ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000 ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310 Call Trace: [<ffffffff81380b0e>] dump_stack+0x55/0x76 [<ffffffff81038635>] warn_slowpath_common+0x7c/0x96 [<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212 [<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43 [<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82 [<ffffffff81182382>] ? sysfs_open_file+0x32/0x212 [<ffffffff811823c7>] sysfs_open_file+0x77/0x212 [<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac [<ffffffff81122562>] do_dentry_open+0x17c/0x257 [<ffffffff8112267e>] finish_open+0x41/0x4f [<ffffffff81130225>] do_last+0x80c/0x9ba [<ffffffff8112dbbd>] ? inode_permission+0x40/0x42 [<ffffffff81130606>] path_openat+0x233/0x4a1 [<ffffffff81130b7e>] do_filp_open+0x35/0x85 [<ffffffff8113b787>] ? __alloc_fd+0x172/0x184 [<ffffffff811232ea>] do_sys_open+0x6b/0xfa [<ffffffff811233a7>] SyS_openat+0xf/0x11 [<ffffffff8138c812>] system_call_fastpath+0x16/0x1b The failure to restore cpufreq devices on cancelled hibernation is not a new bug. It is caused by the ACPI _PPC call failing unless the hibernate is completed. This makes the acpi_cpufreq driver fail its init. Previously, the cpufreq device could be restored by offlining the cpu temporarily. And as a complete hibernation cycle would do this, it would be automatically restored most of the time. But after commit 5302c3fb the leftover sysfs attributes will block any device add action. Therefore offlining and onlining CPU 1 will no longer restore the cpufreq object, and a complete suspend/resume cycle will replace it with garbage. Fixes: 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume") Signed-off-by:
-
Dan Carpenter authored
commit bdefc8cb upstream. We should be taking the minimum here instead of the max. It could lead to a buffer overflow. Fixes: 438d99e3 ('drm/nvd0/disp: initial crtc object implementation') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> a/drm/nv50_display.c b/drm/nv50_display.c index f8e66c08b11a..4e384a2f99c3 100644 Signed-off-by:
-
Dan Carpenter authored
commit cb4855b4 upstream. We fixed this to use free_netdev() instead of kfree() but unfortunately free_netdev() doesn't accept NULL pointers. Smatch complains about this, it's not something I discovered through testing. Fixes: 3030d40b ('staging: vt6655: use free_netdev instead of kfree') Fixes: 0a438d5b ('staging: vt6656: use free_netdev instead of kfree') Signed-off-by:
-
Dan Carpenter authored
commit d6daef95 upstream. We assume that "pmic" could be NULL and then dereference it two lines later. I fix this by moving the dereference inside the NULL check. Fixes: c013f0a5 ('mfd: Add pm8xxx irq support') Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Dan Carpenter authored
commit 78032f9b upstream. We recently added a new error path and it needs a dev_put(). Fixes: 7adac1ec ('6lowpan: Only make 6lowpan links to IEEE802154 devices') Signed-off-by:
-
Ben Hutchings authored
commit 2b462638 upstream. If we failed to copy from the structure, writing back the flags leaks 31 bits of kernel memory (the rest of the ir_flags field). In any case, if we cannot copy from/to the structure, why should we expect putting just the flags to work? Also make sure ocfs2_info_handle_freeinode() returns the right error code if the copy_to_user() fails. Fixes: ddee5cdb ('Ocfs2: Add new OCFS2_IOC_INFO ioctl for ocfs2 v8.') Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Cc: Joel Becker <jlbec@evilplan.org> Acked-by:
Mark Fasheh <mfasheh@suse.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Theodore Ts'o authored
commit 2ba3e6e8 upstream. It is OK for s_first_meta_bg to be equal to the number of block group descriptor blocks. (It rarely happens, but it shouldn't cause any problems.) https://bugzilla.kernel.org/show_bug.cgi?id=194567 Fixes: 3a4b77cdSigned-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Eryu Guan authored
commit 3a4b77cd upstream. Ralf Spenneberg reported that he hit a kernel crash when mounting a modified ext4 image. And it turns out that kernel crashed when calculating fs overhead (ext4_calculate_overhead()), this is because the image has very large s_first_meta_bg (debug code shows it's 842150400), and ext4 overruns the memory in count_overhead() when setting bitmap buffer, which is PAGE_SIZE. ext4_calculate_overhead(): buf = get_zeroed_page(GFP_NOFS); <=== PAGE_SIZE buffer blks = count_overhead(sb, i, buf); count_overhead(): for (j = ext4_bg_num_gdb(sb, grp); j > 0; j--) { <=== j = 842150400 ext4_set_bit(EXT4_B2C(sbi, s++), buf); <=== buffer overrun count++; } This can be reproduced easily for me by this script: #!/bin/bash rm -f fs.img mkdir -p /mnt/ext4 fallocate -l 16M fs.img mke2fs -t ext4 -O bigalloc,meta_bg,^resize_inode -F fs.img debugfs -w -R "ssv first_meta_bg 842150400" fs.img mount -o loop fs.img /mnt/ext4 Fix it by validating s_first_meta_bg first at mount time, and refusing to mount if its value exceeds the largest possible meta_bg number. [js] use EXT4_HAS_INCOMPAT_FEATURE instead of new ext4_has_feature_meta_bg Reported-by:
Ralf Spenneberg <ralf@os-t.de> Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
Andreas Dilger <adilger@dilger.ca> Signed-off-by:
-
- 01 Mar, 2017 5 commits
-
-
Dan Carpenter authored
commit d7cf0c34 upstream. At first glance it looks like there is a missing curly brace but actually the code works the same either way. I have adjusted the indenting but left the code the same. Signed-off-by:
-
Michael Schenk authored
commit 575ddce0 upstream. In the function rtl_usb_start we pre-allocate a certain number of urbs for RX path but they will not be freed when calling rtl_usb_stop. This results in leaking urbs when doing ifconfig up and down. Eventually, the system has no available urbs. Signed-off-by:
Michael Schenk <michael.schenk@albis-elcon.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Thomas Gleixner authored
commit 6cf18e69 upstream. This interrupt handler is broken in several ways: - It loops forever when the op code is not decodeable - It never returns IRQ_HANDLED because the only way to exit the loop returns IRQ_NONE unconditionally. The whole concept of this is broken. Creating devices in an interrupt handler is beyond any point of sanity. Make it at least behave halfways sane so accidental users do not have to deal with a hard to debug lockup. Fixes: e809c22b ("goldfish: add the goldfish virtual bus") Reported-by:
Gabriel C <nix.or.die@gmail.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Acked-by:
-
Thomas Gleixner authored
commit 47512cfd upstream. The goldfish platform code registers the platform device unconditionally which causes havoc in several ways if the goldfish_pdev_bus driver is enabled: - Access to the hardcoded physical memory region, which is either not available or contains stuff which is completely unrelated. - Prevents that the interrupt of the serial port can be requested - In case of a spurious interrupt it goes into a infinite loop in the interrupt handler of the pdev_bus driver (which needs to be fixed seperately). Add a 'goldfish' command line option to make the registration opt-in when the platform is compiled in. I'm seriously grumpy about this engineering trainwreck, which has seven SOBs from Intel developers for 50 lines of code. And none of them figured out that this is broken. Impressive fail! Fixes: ddd70cf9 ("goldfish: platform device for x86") Reported-by:
-
Johan Hovold authored
commit 9fef37d7 upstream. The current implementation failed to detect short transfers, something which could lead to bits of the uninitialised heap transfer buffer leaking to user space. Fixes: 149fc791 ("USB: ark3116: Setup some basic infrastructure for new ark3116 driver.") Fixes: f4c1e8d5 ("USB: ark3116: Make existing functions 16450-aware and add close and release functions.") Reviewed-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
