Add driver for the HDMI/eDP TX Combo PHY found on Rockchip RK3588 SoC.

The PHY is based on a Samsung IP block and supports HDMI 2.1 TMDS, FRL
and eDP links.  The maximum data rate is 12Gbps (FRL), while the minimum
is 250Mbps (TMDS).

Only the TMDS link is currently supported.
Co-developed-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240214-phy-hdptx-v4-2-e7974f46c1a7@collabora.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add dt-binding schema for the HDMI/eDP Transmitter Combo PHY found on
Rockchip RK3588 SoC.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240214-phy-hdptx-v4-1-e7974f46c1a7@collabora.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The resume callback restores the submode of each PHY.

It uses the submode stored in struct phy_gmii_sel_phy_priv (variable
phy_if_mode). The submode was saved by the set_mode PHY operation.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240125171754.773909-1-thomas.richard@bootlin.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

This is a new driver that supports the MIPI CSI CD-PHY version 0.5

The number of PHYs depend on the SoC.
Each PHY can support D-PHY only or CD-PHY configuration.
The driver supports only D-PHY mode, so CD-PHY
compatible PHY are configured in D-PHY mode.

[Julien Stephan: simplify driver model: one instance per phy vs
one instance for all phys]
Signed-off-by: Louis Kuo <louis.kuo@mediatek.com>
Signed-off-by: Phi-bang Nguyen <pnguyen@baylibre.com>
[Julien Stephan: refactor code]
Co-developed-by: Julien Stephan <jstephan@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240111101738.468916-1-jstephan@baylibre.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

This adds the bindings, for the MIPI CD-PHY module v0.5 embedded in
some Mediatek soc, such as the mt8365
Signed-off-by: Florian Sylvestre <fsylvestre@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240111101504.468169-2-jstephan@baylibre.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add a separate compatible and registers map table for TI J7200.
TI J7200 uses Torrent SD0805 version which is a special version
derived from Torrent SD0801 with some differences in register
configurations.

Add register sequences for USXGMII(156.25MHz) + SGMII/QSGMII(100MHz)
multilink config for TI J7200. USXGMII uses PLL0 and SGMII/QSGMII
uses PLL1.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-6-sjakhade@cadence.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

TI J7200 uses Torrent SD0805 version which is a special version derived
from Torrent SD0801 with some differences in register configurations.
Add a separate compatible for TI J7200 platforms.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-5-sjakhade@cadence.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add register sequences for USXGMII(156.25MHz) + SGMII/QSGMII(100MHz)
multilink configuration. USXGMII uses PLL0 and SGMII/QSGMII uses PLL1.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-4-sjakhade@cadence.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Torrent PHY can have separate input reference clocks for PLL0 and PLL1.
Add support for dual reference clock multilink configurations.

Add register sequences for PCIe(100MHz) + USXGMII(156.25MHz) multilink
configuration. PCIe uses PLL0 and USXGMII uses PLL1.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-3-sjakhade@cadence.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add a new optional input reference clock (pll1_refclk) for PLL1.
Update bindings to support dual reference clock multilink configurations.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-2-sjakhade@cadence.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Device drivers should just rely on the clocks provided by the devicetree
and enable/disable them based on the requirement. There is no need to
validate the clocks provided by devicetree in the driver. That's the job
of DT schema.

So let's switch to devm_clk_bulk_get_all() API that just gets the clocks
provided by devicetree and remove hardcoded clocks info.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-2-58a49d2f4605@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

All QMP UFS PHYs except MSM8996 require 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC or TCSR (since SM8550)

MSM8996 only requires 'ref' and 'qref' clocks. Hence, fix the binding to
reflect the actual clock topology.

This change obviously breaks the ABI, but it is inevitable since the
clock topology needs to be accurately described in the binding.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-1-58a49d2f4605@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Follow the example of the rest of the QMP PHY drivers and move SGMII PCS
registers to a separate header file.

Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-8-a463d0b57836@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

The Qualcomm SGMII SerDes PHY is a QMP PHY. As such, it uses standard
registers for QSERDES COM/RX/TX regions. Use register defines from the
existing headers.

Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-7-a463d0b57836@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

None of the PHYs supported by the USBC driver need power down delay.
Drop corresponding flag and code.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-6-a463d0b57836@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Move bit definitions for the common headers to the common phy-qcom-qmp.h
header.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-5-a463d0b57836@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Split the DP PHY register definitions to separate headers, removing them
from the global one.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-4-a463d0b57836@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Move common init tables code to the common header phy-qcom-qmp-common.h.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-3-a463d0b57836@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

All PHYs supported by qmp-usb-legacy driver don't have issues with the
PCS region. Replace qmp_usb_legacy_iomap() with devm_of_iomap().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-2-a463d0b57836@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

All PHYs supported by usb-legacy have two lanes. Drop support for
single-lane configuration.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad DYbcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-1-a463d0b57836@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Align PCIe0 PHY settings with SM8550 latest PCIe PHY Hardware Programming
Guide.
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Link: https://lore.kernel.org/r/1703742157-69840-3-git-send-email-quic_qianyu@quicinc.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Align PCIe1 PHY settings with SM8550 latest PCIe PHY Hardware Programming
Guide.
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Link: https://lore.kernel.org/r/1703742157-69840-2-git-send-email-quic_qianyu@quicinc.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Armada 38x supports 3 functions on serdes #0:
- pcie port 0
- sata port 0
- gbe port 0

Add missing entry for gbe port 0 on serdes 0 to the gbe_mux array.

Because this array looks obscure to new readers, also add a comment
explaining the meaning of rows, columns and values.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240106-fix-a38x-comphy-sd0-gbe0-v1-1-c7fd87272050@solid-run.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add the X1E80100 G3 and G4 configurations.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231223-x1e80100-phy-pcie-v2-3-223c0556908a@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

For consistency, add the QMP v6 registers layout even though
they are the same as v5. Also switch all QMP v6 PHYs to use this
new layout.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231223-x1e80100-phy-pcie-v2-2-223c0556908a@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Document the QMP PCIe PHYs on the X1E80100 platform.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20231223-x1e80100-phy-pcie-v2-1-223c0556908a@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Provide PHY configuration for the USB QMP PHY for the SDM630 / SDM660
platforms.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240116-sdm660-usb3-support-v1-2-2fbd683aea77@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Declare the USB-C QMP PHY present on the Qualcomm SDM660 / SDM630
platforms.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240116-sdm660-usb3-support-v1-1-2fbd683aea77@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

The QMP USB PHYs on msm8998, qcm2290 and some other platforms don't have
the PCS_MISC_CLAMP_ENABLE register. Instead they need to toggle the
register in the TCSR space. Make the new phy-qcom-qmp-usbc driver
correctly handle the clamp register.

Fixes: a51969fa ("phy: qcom-qmp: Add QMP V3 USB3 PHY support for msm8998")
Fixes: 8abe5e77 ("phy: qcom-qmp: Add QCM2290 USB3 PHY support")
Cc: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-3-a950c223f10f@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

The QMP USB PHYs on msm8998, qcm2290 and some other platforms don't have
the PCS_MISC_CLAMP_ENABLE register. Instead they need to toggle the
register in the TCSR space. Declare the registers accessible through the
TCSR space.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-2-a950c223f10f@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

The USB-C PHYs on the msm8998, QCM2290 and SM6115 platforms use special
register to control which lanes of the Type-C port are used for the
SuperSpeed USB connection. Mimic the qmp-combo driver and handle this
register.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-12-182d9aa0a5b3@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Now as all dual-lane PHYs have been migrated to a new driver, drop
support for dual lanes configuration. If the PHY uses two lanes for USB,
it is symthom that it should use either a combo USB+DP or a USB-C PHY
driver.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-11-182d9aa0a5b3@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

In preparation to adding Type-C handling for MSM8998, QCM2290 and SM6115
platforms, create new QMP USB-C PHY driver by splitting mentioned
platforms to a separate file. In future it will also be extended with
support for the DisplayPort handling. It will also be reused later for
such platforms as SDM660, SM6125, SM6150.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-10-182d9aa0a5b3@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Extend the Qualcomm USB-C QMP PHY schema with the USB-C related entry
points: orientation-switch property and USB-C connection graph.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-4-182d9aa0a5b3@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

In preparation to defining the USB-C handling on MSM8998, QCM2290 and
SM6115 split existing QMP USB3 PHY schema into pure USB3 and USB-C
schema definitions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-3-182d9aa0a5b3@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

On SM8550, two sets of UFS PHY settings are provided, one set is to support
HS-G5, another set is to support HS-G4 and lower gears. The two sets of PHY
settings are programming different values to different registers, mixing
the two sets and/or overwriting one set with another set is definitely not
blessed by UFS PHY designers.

To add HS-G5 support for SM8550, split the two sets of PHY settings into
their dedicated overlay tables, only the common parts of the two sets of
PHY settings are left in the .tbls.

Consider we are going to add even higher gear support in future, to avoid
adding more tables with different names, rename the .tbls_hs_g4 and make it
an array, a size of 2 is enough as of now.

In this case, .tbls alone is not a complete set of PHY settings, so either
tbls_hs_overlay[0] or tbls_hs_overlay[1] must be applied on top of the
.tbls to become a complete set of PHY settings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1703557892-1822-1-git-send-email-quic_cang@quicinc.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The SC7180 UFS PHY is identical to the one found on SM7150. Add a
compatible for it.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: David Wronek <davidwronek@gmail.com>
Link: https://lore.kernel.org/r/20240121-sm7125-upstream-v4-5-f7d1212c8ebb@gmail.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Document the QMP UFS PHY compatible for SC7180
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Wronek <davidwronek@gmail.com>
Link: https://lore.kernel.org/r/20240121-sm7125-upstream-v4-3-f7d1212c8ebb@gmail.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...