- 23 Jan, 2020 28 commits
-
-
Jian-Hong Pan authored
commit 176a7fca upstream. Some of ASUS laptops like UX431FL keyboard backlight cannot be set to brightness 0. According to ASUS' information, the brightness should be 0x80 ~ 0x83. This patch fixes it by following the logic. Fixes: e9809c0b ("asus-wmi: add keyboard backlight support") Signed-off-by:
Jian-Hong Pan <jian-hong@endlessm.com> Reviewed-by:
Daniel Drake <drake@endlessm.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Xiang Chen authored
commit 465f4eda upstream. If an attached disk with protection information enabled is reformatted to Type 0 the revalidation code does not clear the original protection type and subsequent accesses will keep setting RDPROTECT/WRPROTECT. Set the protection type to 0 if the disk reports PROT_EN=0 in READ CAPACITY(16). [mkp: commit desc] Fixes: fe542396 ("[SCSI] sd: Ensure we correctly disable devices with unknown protection type") Link: https://lore.kernel.org/r/1578532344-101668-1-git-send-email-chenxiang66@hisilicon.comSigned-off-by:
Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
James Bottomley authored
commit 529244bd upstream. Doing an add/remove/add on a SCSI device in an enclosure leads to an oops caused by poisoned values in the enclosure device list pointers. The reason is because we are keeping the enclosure device across the enclosed device add/remove/add but the current code is doing a device_add/device_del/device_add on it. This is the wrong thing to do in sysfs, so fix it by not doing a device_del on the enclosure device simply because of a hot remove of the drive in the slot. [mkp: added missing email addresses] Fixes: 43d8eb9c ("[SCSI] ses: add support for enclosure component hot removal") Link: https://lore.kernel.org/r/1578532892.3852.10.camel@HansenPartnership.comSigned-off-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Reported-by:
Luo Jiaxing <luojiaxing@huawei.com> Tested-by:
John Garry <john.garry@huawei.com> Signed-off-by:
-
Bart Van Assche authored
commit e88982ad upstream. The code added by this patch is similar to the code that already exists in ibmvscsis_determine_resid(). This patch has been tested by running the following command: strace sg_raw -r 1k /dev/sdb 12 00 00 00 60 00 -o inquiry.bin |& grep resid= Link: https://lore.kernel.org/r/20191105214632.183302-1-bvanassche@acm.org Fixes: a42d985b ("ib_srpt: Initial SRP Target merge for v3.3-rc1") Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Acked-by:
Honggang Li <honli@redhat.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Nathan Chancellor authored
commit 7935799e upstream. Clang warns: ../fs/cifs/smb2file.c:70:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] if (oparms->tcon->use_resilient) { ^ ../fs/cifs/smb2file.c:66:2: note: previous statement is here if (rc) ^ 1 warning generated. This warning occurs because there is a space after the tab on this line. Remove it so that the indentation is consistent with the Linux kernel coding style and clang no longer warns. Fixes: 592fafe6 ("Add resilienthandles mount parm") Link: https://github.com/ClangBuiltLinux/linux/issues/826Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Taehee Yoo authored
commit 3ed0a1d5 upstream. The supervision frame is L2 frame. When supervision frame is created, hsr module doesn't set network header. If tap routine is enabled, dev_queue_xmit_nit() is called and it checks network_header. If network_header pointer wasn't set(or invalid), it resets network_header and warns. In order to avoid unnecessary warning message, resetting network_header is needed. Test commands: ip netns add nst ip link add veth0 type veth peer name veth1 ip link add veth2 type veth peer name veth3 ip link set veth1 netns nst ip link set veth3 netns nst ip link set veth0 up ip link set veth2 up ip link add hsr0 type hsr slave1 veth0 slave2 veth2 ip a a 192.168.100.1/24 dev hsr0 ip link set hsr0 up ip netns exec nst ip link set veth1 up ip netns exec nst ip link set veth3 up ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3 ip netns exec nst ip a a 192.168.100.2/24 dev hsr1 ip netns exec nst ip link set hsr1 up tcpdump -nei veth0 Splat looks like: [ 175.852292][ C3] protocol 88fb is buggy, dev veth0 Fixes: f421436a ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Geert Uytterhoeven authored
commit d935bd50 upstream. When a GPIO offset in a lookup table is out-of-range, the printed error message (1) does not include the actual out-of-range value, and (2) contains an off-by-one error in the upper bound. Avoid user confusion by also printing the actual GPIO offset, and correcting the upper bound of the range. While at it, use "%u" for unsigned int. Sample impact: -requested GPIO 0 is out of range [0..32] for chip e6052000.gpio +requested GPIO 0 (45) is out of range [0..31] for chip e6052000.gpio Fixes: 2a3cf6a3 ("gpiolib: return -ENOENT if no GPIO mapping exists") Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20191127095919.4214-1-geert+renesas@glider.beSigned-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Jon Derrick authored
commit 7d4e6ccd upstream. This adds the missing teardown step that removes the device link from the group when the device addition fails. Signed-off-by:
Jon Derrick <jonathan.derrick@intel.com> Fixes: 797a8b4d ("iommu: Handle default domain attach failure") Reviewed-by:
Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Ran Bi authored
commit 653997ee upstream. Alarm registers high byte was reserved for other functions. This add mask in alarm registers operation functions. This also fix error condition in interrupt handler. Fixes: fc297911 ("rtc: mediatek: Add MT6397 RTC driver") Signed-off-by:
Ran Bi <ran.bi@mediatek.com> Signed-off-by:
Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Link: https://lore.kernel.org/r/1576057435-3561-6-git-send-email-hsin-hsiung.wang@mediatek.comSigned-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
YueHaibing authored
commit 1d3ff095 upstream. If dccp_feat_push_change fails, we forget free the mem which is alloced by kmemdup in dccp_feat_clone_sp_val. Reported-by:
Hulk Robot <hulkci@huawei.com> Fixes: e8ef967a ("dccp: Registration routines for changing feature values") Reviewed-by:
Mukesh Ojha <mojha@codeaurora.org> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Theodore Ts'o authored
commit 4ea99936 upstream. It's possible to specify a non-zero s_want_extra_isize via debugging option, and this can cause bad things(tm) to happen when using a file system with an inode size of 128 bytes. Add better checking when the file system is mounted, as well as when we are actually doing the trying to do the inode expansion. Link: https://lore.kernel.org/r/20191110121510.GH23325@mit.edu Reported-by: syzbot+f8d6f8386ceacdbfff57@syzkaller.appspotmail.com Reported-by: syzbot+33d7ea72e47de3bdf4e1@syzkaller.appspotmail.com Reported-by: syzbot+44b6763edfc17144296f@syzkaller.appspotmail.com Signed-off-by:
Theodore Ts'o <tytso@mit.edu> [bwh: Backported to 4.9: adjust context] Signed-off-by:
-
Barret Rhoden authored
commit 7bc04c5c upstream. When remounting with debug_want_extra_isize, we were not performing the same checks that we do during a normal mount. That allowed us to set a value for s_want_extra_isize that reached outside the s_inode_size. Fixes: e2b911c5 ("ext4: clean up feature test macros with predicate functions") Reported-by: syzbot+f584efa0ac7213c226b7@syzkaller.appspotmail.com Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Barret Rhoden <brho@google.com> Signed-off-by:
-
Navid Emamdoost authored
commit 6f3ef5c2 upstream. In the implementation of i2400m_op_rfkill_sw_toggle() the allocated buffer for cmd should be released before returning. The documentation for i2400m_msg_to_dev() says when it returns the buffer can be reused. Meaning cmd should be released in either case. Move kfree(cmd) before return to be reached by all execution paths. Fixes: 2507e6ab ("wimax: i2400: fix memory leak") Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by:
-
Navid Emamdoost authored
commit 2507e6ab upstream. In i2400m_op_rfkill_sw_toggle cmd buffer should be released along with skb response. Signed-off-by:
-
Vandana BN authored
commit 5d2e73a5 upstream. SyzKaller hit the null pointer deref while reading from uninitialized udev->product in zr364xx_vidioc_querycap(). ================================================================== BUG: KASAN: null-ptr-deref in read_word_at_a_time+0xe/0x20 include/linux/compiler.h:274 Read of size 1 at addr 0000000000000000 by task v4l_id/5287 CPU: 1 PID: 5287 Comm: v4l_id Not tainted 5.1.0-rc3-319004-g43151d6 #6 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xe8/0x16e lib/dump_stack.c:113 kasan_report.cold+0x5/0x3c mm/kasan/report.c:321 read_word_at_a_time+0xe/0x20 include/linux/compiler.h:274 strscpy+0x8a/0x280 lib/string.c:207 zr364xx_vidioc_querycap+0xb5/0x210 drivers/media/usb/zr364xx/zr364xx.c:706 v4l_querycap+0x12b/0x340 drivers/media/v4l2-core/v4l2-ioctl.c:1062 __video_do_ioctl+0x5bb/0xb40 drivers/media/v4l2-core/v4l2-ioctl.c:2874 video_usercopy+0x44e/0xf00 drivers/media/v4l2-core/v4l2-ioctl.c:3056 v4l2_ioctl+0x14e/0x1a0 drivers/media/v4l2-core/v4l2-dev.c:364 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0xced/0x12f0 fs/ioctl.c:696 ksys_ioctl+0xa0/0xc0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x74/0xb0 fs/ioctl.c:718 do_syscall_64+0xcf/0x4f0 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x7f3b56d8b347 Code: 90 90 90 48 8b 05 f1 fa 2a 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 90 90 90 90 90 90 90 90 90 90 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d c1 fa 2a 00 31 d2 48 29 c2 64 RSP: 002b:00007ffe005d5d68 EFLAGS: 00000202 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f3b56d8b347 RDX: 00007ffe005d5d70 RSI: 0000000080685600 RDI: 0000000000000003 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000400884 R13: 00007ffe005d5ec0 R14: 0000000000000000 R15: 0000000000000000 ================================================================== For this device udev->product is not initialized and accessing it causes a NULL pointer deref. The fix is to check for NULL before strscpy() and copy empty string, if product is NULL Reported-by: syzbot+66010012fd4c531a1a96@syzkaller.appspotmail.com Signed-off-by:
Vandana BN <bnvandana@gmail.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> [bwh: Backported to 4.9: This function uses strlcpy() instead of strscpy()] Signed-off-by:
-
Jouni Malinen authored
commit 3e493173 upstream. The Layer 2 Update frame is used to update bridges when a station roams to another AP even if that STA does not transmit any frames after the reassociation. This behavior was described in IEEE Std 802.11F-2003 as something that would happen based on MLME-ASSOCIATE.indication, i.e., before completing 4-way handshake. However, this IEEE trial-use recommended practice document was published before RSN (IEEE Std 802.11i-2004) and as such, did not consider RSN use cases. Furthermore, IEEE Std 802.11F-2003 was withdrawn in 2006 and as such, has not been maintained amd should not be used anymore. Sending out the Layer 2 Update frame immediately after association is fine for open networks (and also when using SAE, FT protocol, or FILS authentication when the station is actually authenticated by the time association completes). However, it is not appropriate for cases where RSN is used with PSK or EAP authentication since the station is actually fully authenticated only once the 4-way handshake completes after authentication and attackers might be able to use the unauthenticated triggering of Layer 2 Update frame transmission to disrupt bridge behavior. Fix this by postponing transmission of the Layer 2 Update frame from station entry addition to the point when the station entry is marked authorized. Similarly, send out the VLAN binding update only if the STA entry has already been authorized. Signed-off-by:
Jouni Malinen <jouni@codeaurora.org> Reviewed-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Dedy Lansky authored
commit 30ca1aa5 upstream. Make ieee80211_send_layer2_update() a common function so other drivers can re-use it. Signed-off-by:
Dedy Lansky <dlansky@codeaurora.org> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [bwh: Backported to 4.9 as dependency of commit 3e493173 "mac80211: Do not send Layer 2 Update frame before authorization": - Retain type-casting of skb_put() return value - Adjust context] Signed-off-by:
-
Laura Abbott authored
commit 82034c23 upstream. Commit 15122ee2 ("arm64: Enforce BBM for huge IO/VMAP mappings") disallowed block mappings for ioremap since that code does not honor break-before-make. The same APIs are also used for permission updating though and the extra checks prevent the permission updates from happening, even though this should be permitted. This results in read-only permissions not being fully applied. Visibly, this can occasionaly be seen as a failure on the built in rodata test when the test data ends up in a section or as an odd RW gap on the page table dump. Fix this by using pgattr_change_is_safe instead of p*d_present for determining if the change is permitted. Reviewed-by:
Kees Cook <keescook@chromium.org> Tested-by:
Peter Robinson <pbrobinson@gmail.com> Reported-by:
Laura Abbott <labbott@redhat.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Will Deacon authored
commit 15122ee2 upstream. ioremap_page_range doesn't honour break-before-make and attempts to put down huge mappings (using p*d_set_huge) over the top of pre-existing table entries. This leads to us leaking page table memory and also gives rise to TLB conflicts and spurious aborts, which have been seen in practice on Cortex-A75. Until this has been resolved, refuse to put block mappings when the existing entry is found to be present. Fixes: 324420bf ("arm64: add support for ioremap() block mappings") Reported-by:
Hanjun Guo <hanjun.guo@linaro.org> Reported-by:
Lei Li <lious.lilei@hisilicon.com> Acked-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Ben Hutchings authored
This is preparation for the following backported fixes. It was done upstream as part of commit 20a004e7 "arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables", the rest of which does not seem suitable for stable. Signed-off-by:
-
Kristina Martsenko authored
commit 19338304 upstream. Instead of open coding the generation of page table entries, use the macros/functions that exist for this - pfn_p*d and p*d_populate. Most code in the kernel already uses these macros, this patch tries to fix up the few places that don't. This is useful for the next patch in this series, which needs to change the page table entry logic, and it's better to have that logic in one place. The KVM extended ID map is special, since we're creating a level above CONFIG_PGTABLE_LEVELS and the required function isn't available. Leave it as is and add a comment to explain it. (The normal kernel ID map code doesn't need this change because its page tables are created in assembly (__create_page_tables)). Tested-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by:
Marc Zyngier <marc.zyngier@arm.com> Tested-by:
Bob Picco <bob.picco@oracle.com> Reviewed-by:
Kristina Martsenko <kristina.martsenko@arm.com> Signed-off-by:
-
Ard Biesheuvel authored
commit e98216b5 upstream. Now that we take care not manipulate the live kernel page tables in a way that may lead to TLB conflicts, the case where a table mapping is replaced by a block mapping can no longer occur. So remove the handling of this at the PUD and PMD levels, and instead, BUG() on any occurrence of live kernel page table manipulations that modify anything other than the permission bits. Since mark_rodata_ro() is the only caller where the kernel mappings that are being manipulated are actually live, drop the various conditional flush_tlb_all() invocations, and add a single call to mark_rodata_ro() instead. Signed-off-by:
-
Sanjay Konduri authored
commit abd39c6d upstream. Observed crash in some scenarios when assertion has occurred, this is because hw structure is freed and is tried to get accessed in some functions where null check is already present. So, avoided the crash by making the hw to NULL after freeing. Signed-off-by:
Sanjay Konduri <sanjay.konduri@redpinesignals.com> Signed-off-by:
Sushant Kumar Mishra <sushant.mishra@redpinesignals.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Arnd Bergmann authored
commit ad312f95 upstream. The select() implementation is carefully tuned to put a sensible amount of data on the stack for holding a copy of the user space fd_set, but not too large to risk overflowing the kernel stack. When building a 32-bit kernel with clang, we need a little more space than with gcc, which often triggers a warning: fs/select.c:619:5: error: stack frame size of 1048 bytes in function 'core_sys_select' [-Werror,-Wframe-larger-than=] int core_sys_select(int n, fd_set __user *inp, fd_set __user *outp, I experimentally found that for 32-bit ARM, reducing the maximum stack usage by 64 bytes keeps us reliably under the warning limit again. Link: http://lkml.kernel.org/r/20190307090146.1874906-1-arnd@arndb.deSigned-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Andi Kleen <ak@linux.intel.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Cc: Eric Dumazet <edumazet@google.com> Cc: "Darrick J. Wong" <darrick.wong@oracle.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Miles Chen <miles.chen@mediatek.com> Signed-off-by:
-
Arnd Bergmann authored
commit 3499e87e upstream. clang inlines the dev_ethtool() more aggressively than gcc does, leading to a larger amount of used stack space: net/core/ethtool.c:2536:24: error: stack frame size of 1216 bytes in function 'dev_ethtool' [-Werror,-Wframe-larger-than=] Marking the sub-functions that require the most stack space as noinline_for_stack gives us reasonable behavior on all compilers. Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
Jiri Kosina authored
[ Upstream commit 9e635c28 ] hidraw and uhid device nodes are always available for writing so we should always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when there is nothing to read. Reported-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Marcel Holtmann authored
[ Upstream commit 9f3b61dc ] When polling a connected /dev/hidrawX device, it is useful to get the EPOLLOUT when writing is possible. Since writing is possible as soon as the device is connected, always return it. Right now EPOLLOUT is only returned when there are also input reports are available. This works if devices start sending reports when connected, but some HID devices might need an output report first before sending any input reports. This change will allow using EPOLLOUT here as well. Fixes: 378b8037 ("hidraw: Return EPOLLOUT from hidraw_poll") Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Fabian Henneke authored
[ Upstream commit 378b8037 ] Always return EPOLLOUT from hidraw_poll when a device is connected. This is safe since writes are always possible (but will always block). hidraw does not support non-blocking writes and instead always calls blocking backend functions on write requests. Hence, so far, a call to poll never returned EPOLLOUT, which confuses tools like socat. Signed-off-by:
Fabian Henneke <fabian.henneke@gmail.com> In-reply-to: <CA+hv5qkyis03CgYTWeWX9cr0my-d2Oe+aZo+mjmWRXgjrGqyrw@mail.gmail.com> Signed-off-by:
-
- 14 Jan, 2020 12 commits
-
-
Greg Kroah-Hartman authored
-
Akeem G Abodunrin authored
commit bc8a76a1 upstream. Intel ID: PSIRT-TA-201910-001 CVEID: CVE-2019-14615 Intel GPU Hardware prior to Gen11 does not clear EU state during a context switch. This can result in information leakage between contexts. For Gen8 and Gen9, hardware provides a mechanism for fast cleardown of the EU state, by issuing a PIPE_CONTROL with bit 27 set. We can use this in a context batch buffer to explicitly cleardown the state on every context switch. As this workaround is already in place for gen8, we can borrow the code verbatim for Gen9. Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by:
Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Cc: Kumar Valsan Prathap <prathap.kumar.valsan@intel.com> Cc: Chris Wilson <chris.p.wilson@intel.com> Cc: Balestrieri Francesco <francesco.balestrieri@intel.com> Cc: Bloomfield Jon <jon.bloomfield@intel.com> Cc: Dutt Sudeep <sudeep.dutt@intel.com> Signed-off-by:
-
Florian Westphal authored
commit 22dad713 upstream. The set uadt functions assume lineno is never NULL, but it is in case of ip_set_utest(). syzkaller managed to generate a netlink message that calls this with LINENO attr present: general protection fault: 0000 [#1] PREEMPT SMP KASAN RIP: 0010:hash_mac4_uadt+0x1bc/0x470 net/netfilter/ipset/ip_set_hash_mac.c:104 Call Trace: ip_set_utest+0x55b/0x890 net/netfilter/ipset/ip_set_core.c:1867 nfnetlink_rcv_msg+0xcf2/0xfb0 net/netfilter/nfnetlink.c:229 netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477 nfnetlink_rcv+0x1ba/0x460 net/netfilter/nfnetlink.c:563 pass a dummy lineno storage, its easier than patching all set implementations. This seems to be a day-0 bug. Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Reported-by: syzbot+34bd2369d38707f3f4a7@syzkaller.appspotmail.com Fixes: a7b4f989 ("netfilter: ipset: IP set core support") Signed-off-by:
Florian Westphal <fw@strlen.de> Acked-by:
Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Florian Westphal authored
commit 1b789577 upstream. We get crash when the targets checkentry function tries to make use of the network namespace pointer for arptables. When the net pointer got added back in 2010, only ip/ip6/ebtables were changed to initialize it, so arptables has this set to NULL. This isn't a problem for normal arptables because no existing arptables target has a checkentry function that makes use of par->net. However, direct users of the setsockopt interface can provide any target they want as long as its registered for ARP or UNPSEC protocols. syzkaller managed to send a semi-valid arptables rule for RATEEST target which is enough to trigger NULL deref: kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN RIP: xt_rateest_tg_checkentry+0x11d/0xb40 net/netfilter/xt_RATEEST.c:109 [..] xt_check_target+0x283/0x690 net/netfilter/x_tables.c:1019 check_target net/ipv4/netfilter/arp_tables.c:399 [inline] find_check_entry net/ipv4/netfilter/arp_tables.c:422 [inline] translate_table+0x1005/0x1d70 net/ipv4/netfilter/arp_tables.c:572 do_replace net/ipv4/netfilter/arp_tables.c:977 [inline] do_arpt_set_ctl+0x310/0x640 net/ipv4/netfilter/arp_tables.c:1456 Fixes: add67461 ("netfilter: add struct net * to target parameters") Reported-by: syzbot+d7358a458d8a81aee898@syzkaller.appspotmail.com Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Alan Stern authored
commit 2548288b upstream. It turns out that even though endpoints with a maxpacket length of 0 aren't useful for data transfer, the descriptors do serve other purposes. In particular, skipping them will also skip over other class-specific descriptors for classes such as UVC. This unexpected side effect has caused some UVC cameras to stop working. In addition, the USB spec requires that when isochronous endpoint descriptors are present in an interface's altsetting 0 (which is true on some devices), the maxpacket size _must_ be set to 0. Warning about such things seems like a bad idea. This patch updates an earlier commit which would log a warning and skip these endpoint descriptors. Now we only log a warning, and we don't even do that for isochronous endpoints in altsetting 0. We don't need to worry about preventing endpoints with maxpacket = 0 from ever being used for data transfers; usb_submit_urb() already checks for this. Reported-and-tested-by:
Roger Whittaker <Roger.Whittaker@suse.com> Fixes: d482c7bb ("USB: Skip endpoints with 0 maxpacket length") Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2 Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.orgSigned-off-by:
-
Navid Emamdoost authored
commit a2cdd074 upstream. In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb should be released. Signed-off-by:
Chris Chiu <chiu@endlessm.com> Signed-off-by:
-
Navid Emamdoost authored
commit 0e62395d upstream. In bfad_im_get_stats if bfa_port_get_stats fails, allocated memory needs to be released. Link: https://lore.kernel.org/r/20190910234417.22151-1-navid.emamdoost@gmail.comSigned-off-by:
-
Navid Emamdoost authored
commit db8fd2cd upstream. In mwifiex_pcie_alloc_cmdrsp_buf, a new skb is allocated which should be released if mwifiex_map_pci_memory() fails. The release is added. Fixes: fc331460 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe") Signed-off-by:
Ganapathi Bhat <gbhat@marvell.com> Signed-off-by:
-
Ganapathi Bhat authored
commit 3d94a4a8 upstream. mwifiex_process_country_ie() function parse elements of bss descriptor in beacon packet. When processing WLAN_EID_COUNTRY element, there is no upper limit check for country_ie_len before calling memcpy. The destination buffer domain_info->triplet is an array of length MWIFIEX_MAX_TRIPLET_802_11D(83). The remote attacker can build a fake AP with the same ssid as real AP, and send malicous beacon packet with long WLAN_EID_COUNTRY elemen (country_ie_len > 83). Attacker can force STA connect to fake AP on a different channel. When the victim STA connects to fake AP, will trigger the heap buffer overflow. Fix this by checking for length and if found invalid, don not connect to the AP. This fix addresses CVE-2019-14895. Reported-by:
huangwen <huangwenabc@gmail.com> Signed-off-by:
-
Sudip Mukherjee authored
commit 273f6329 upstream. If the serial device is disconnected and reconnected, it re-enumerates properly but does not link it. fwiw, linking means just saving the port index, so allow it always as there is no harm in saving the same value again even if it tries to relink with the same port. Fixes: fb2b9001 ("tty: link tty and port before configuring it as console") Reported-by:
Kenneth R. Crudup <kenny@panix.com> Signed-off-by:
Sudip Mukherjee <sudipm.mukherjee@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191227174434.12057-1-sudipm.mukherjee@gmail.comSigned-off-by:
-
Sudip Mukherjee authored
commit fb2b9001 upstream. There seems to be a race condition in tty drivers and I could see on many boot cycles a NULL pointer dereference as tty_init_dev() tries to do 'tty->port->itty = tty' even though tty->port is NULL. 'tty->port' will be set by the driver and if the driver has not yet done it before we open the tty device we can get to this situation. By adding some extra debug prints, I noticed that: 6.650130: uart_add_one_port 6.663849: register_console 6.664846: tty_open 6.674391: tty_init_dev 6.675456: tty_port_link_device uart_add_one_port() registers the console, as soon as it registers, the userspace tries to use it and that leads to tty_open() but uart_add_one_port() has not yet done tty_port_link_device() and so tty->port is not yet configured when control reaches tty_init_dev(). Further look into the code and tty_port_link_device() is done by uart_add_one_port(). After registering the console uart_add_one_port() will call tty_port_register_device_attr_serdev() and tty_port_link_device() is called from this. Call add tty_port_link_device() before uart_configure_port() is done and add a check in tty_port_link_device() so that it only links the port if it has not been done yet. Suggested-by:
Jiri Slaby <jslaby@suse.com> Signed-off-by:
-
Michael Straube authored
commit 58dcc5bf upstream. This device was added to the stand-alone driver on github. Add it to the staging driver as well. Link: https://github.com/lwfinger/rtl8188eu/commit/b9b537aa25a8Signed-off-by:
Michael Straube <straube.linux@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191228143725.24455-1-straube.linux@gmail.comSigned-off-by:
-
