The type of arg passed to dmatest_callback is struct dmatest_done.
It refers to test_done in struct dmatest_thread, not done_wait.

Fixes: 6f6a23a2 ("dmaengine: dmatest: move callback wait ...")
Signed-off-by: Yang Shunyong <shunyong.yang@hxt-semitech.com>
Acked-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Sparse warns that 'sprd_dma_prep_dma_memcpy' should be static so make it
static.

drivers/dma/sprd-dma.c:713:32: warning:
symbol'sprd_dma_prep_dma_memcpy' was not declared. Should it be static?
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The hidma driver open codes populating address and IRQ resources from DT.
We have standard functions of_address_to_resource and of_irq_to_resource
for this, so use them instead.

The DT binding states each child should have 2 addresses and 1 IRQ, so we
can simplify the logic and do a fixed size resource allocation. Using the
standard of_address_to_resource will also do any address translation which
was missing.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Monospace is more readable and is also used elsewhere in the docs.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The bullet list documenting the 'struct dma_device' fields has several
nesting errors, making it render improperly. It also has incoherent
formatting: some fields have a description in the same bullet, some in
a sub-bullet.

Fix both to have a correct and coherent formatting.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The test should be >= ARRAY_SIZE() instead of > ARRAY_SIZE().
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This avoid the following error when using an initramfs on wandboard quad
Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Previously enabled clks are only disabled if clk_prepare_enable() fails.
However, there are other error paths were the previously enabled
clocks are not disabled.

To fix the problem, fsl_disable_clocks() now takes the number of clocks
that shall be disabled + unprepared. For existing calls were all clocks
were already successfully prepared + enabled, DMAMUX_NR is passed to
disable + unprepare all clocks.

In error paths were only some clocks were successfully prepared +
enabled the loop counter is passed, in order to disable + unprepare
all successfully prepared + enabled clocks.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Andreas Platschek <andreas.platschek@opentech.at>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The location for destination event channel register has been relocated from
offset 0x28 to 0x40. Update the code accordingly.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Add support for probing the newer HW and also organize MSI capable hardware
into an array for maintenance reasons.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

A new version of the HIDMA IP has been released with bug fixes. Bumping the
hardware version to differentiate from others.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Now that we have a get_match_data() callback as part of the firmware node,
implement the ACPI specific piece for it.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Now that we have a get_match_data() callback as part of the firmware node,
implement the OF specific piece for it.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

There is an OF/ACPI function to obtain the driver data. We want to hide
OF/ACPI details from the device drivers and abstract following the device
family of functions.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

OF has of_device_get_match_data() function to extract driver specific data
structure. Add a similar function for ACPI.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Driver is missing the interrupts if two requests are queued up at the same
time as the interrupt handler is servicing a request that was just
delivered.

The ISR clears the interrupt at the end but it could be clearing the
interrupt for an outstanding event. Therefore, second interrupt never
arrives.

Clear the interrupt first and then check for completions.

Also, make sure that request start and interrupt clear do not overlap in
time by using a spinlock.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

in error path of jz4740_dma_probe(), call clk_disable_unprepare() to clean
up.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 25ce6c35 MIPS: jz4740: Remove custom DMA API
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Commit adfa543e ("dmatest: don't use set_freezable_with_signal()")
introduced a bug (that is in fact documented by the patch commit text)
that leaves behind a dangling pointer. Since the done_wait structure is
allocated on the stack, future invocations to the DMATEST can produce
undesirable results (e.g., corrupted spinlocks).

Commit a9df21e3 ("dmaengine: dmatest: warn user when dma test times
out") attempted to WARN the user that the stack was likely corrupted but
did not fix the actual issue.

This patch fixes the issue by pushing the wait queue and callback
structs into the the thread structure. If a failure occurs due to time,
dmaengine_terminate_all will force the callback to safely call
wake_up_all() without possibility of using a freed pointer.

Cc: stable@vger.kernel.org
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=197605
Fixes: adfa543e ("dmatest: don't use set_freezable_with_signal()")
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Suggested-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Fix ptr_ret.cocci warnings:
drivers/dma/mic_x100_dma.c:483:1-3: WARNING: PTR_ERR_OR_ZERO can be used

Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

_xt_ is being dereferenced before it is null checked, hence there is a
potential null pointer dereference.

Fix this by moving the pointer dereference after _xt_ has been null
checked.

This issue was detected with the help of Coccinelle.

Fixes: 4483320e ("dmaengine: Use Pointer xt after NULL check.")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

If the last test in 'ioat_dma_self_test()' fails, we must release all
the allocated resources and not just part of them.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

SYS/RT/Audio DMAC includes independent data buffers for reading
and writing. Therefore, the read transfer counter and write transfer
counter have different values.
TCR indicates read counter, and TCRB indicates write counter.
The relationship is like below.

	        TCR       TCRB
	[SOURCE] -> [DMAC] -> [SINK]

In the MEM_TO_DEV direction, what really matters is how much data has
been written to the device. If the DMA is interrupted between read and
write, then, the data doesn't end up in the destination, so shouldn't
be counted. TCRB is thus the register we should use in this cases.

In the DEV_TO_MEM direction, the situation is more complex. Both the
read and write side are important. What matters from a data consumer
point of view is how much data has been written to memory.
On the other hand, if the transfer is interrupted between read and
write, we'll end up losing data. It can also be important to report.

In the MEM_TO_MEM direction, what matters is of course how much data
has been written to memory from data consumer point of view.
Here, because read and write have independent data buffers, it will
take a while for TCR and TCRB to become equal. Thus we should check
TCRB in this case, too.

Thus, all cases we should check TCRB instead of TCR.

Without this patch, Sound Capture has noise after PulseAudio support
(= 07b7acb5 ("ASoC: rsnd: update pointer more accurate")), because
the recorder will use wrong residue counter which indicates transferred
from sound device, but in reality the data was not yet put to memory
and recorder will record it.

However, because DMAC is buffering data until it can be transferable
size, TCRB might not be updated.
For example, if consumer doesn't know how much data can be received,
it requests enough size to DMAC. But in reality, it might receive very
few data. In such case, DMAC just buffered it until transferable size,
and no TCRB updated.

In such case, this buffered data will be transferred if CHCR::DE bit was
cleared, and this is happen if rcar_dmac_chan_halt(). In other word, it
happen when consumer called dmaengine_terminate_all().

Because of this behavior, it need to flush buffered data when it returns
"residue" (= dmaengine_tx_status()).
Otherwise, consumer might calculate wrong things if it called
dmaengine_tx_status() and dmaengine_terminate_all() consecutively.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

DMAC reads data from source device, and buffered it until transferable
size for sink device. Because of this behavior, DMAC is including
buffered data .

Now, CHCR DE bit is controlling DMA transfer enable/disable.

If DE bit was cleared during data transferring, or during buffering,
it will flush buffered data if source device was peripheral device
(The buffered data will be removed if source device was memory).
Because of this behavior, driver should ensure that DE bit is actually
0 after clearing.

This patch adds new rcar_dmac_chcr_de_barrier() and call it after CHCR
register access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Pull ARM fixes from Russell King:

 - LPAE fixes for kernel-readonly regions

 - Fix for get_user_pages_fast on LPAE systems

 - avoid tying decompressor to a particular platform if DEBUG_LL is
   enabled

 - BUG if we attempt to return to userspace but the to-be-restored PSR
   value keeps us in privileged mode (defeating an issue that ftracetest
   found)

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: BUG if jumping to usermode address in kernel mode
  ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
  ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
  ARM: make decompressor debug output user selectable
  ARM: fix get_user_pages_fast

Pull irq fixes from Thomas Glexiner:

 - unbreak the irq trigger type check for legacy platforms

 - a handful fixes for ARM GIC v3/4 interrupt controllers

 - a few trivial fixes all over the place

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/matrix: Make - vs ?: Precedence explicit
  irqchip/imgpdc: Use resource_size function on resource object
  irqchip/qcom: Fix u32 comparison with value less than zero
  irqchip/exiu: Fix return value check in exiu_init()
  irqchip/gic-v3-its: Remove artificial dependency on PCI
  irqchip/gic-v4: Add forward definition of struct irq_domain_ops
  irqchip/gic-v3: pr_err() strings should end with newlines
  irqchip/s3c24xx: pr_err() strings should end with newlines
  irqchip/gic-v3: Fix ppi-partitions lookup
  irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
  genirq: Track whether the trigger type has been set

Pull misc x86 fixes from Ingo Molnar:
 - topology enumeration fixes
 - KASAN fix
 - two entry fixes (not yet the big series related to KASLR)
 - remove obsolete code
 - instruction decoder fix
 - better /dev/mem sanity checks, hopefully working better this time
 - pkeys fixes
 - two ACPI fixes
 - 5-level paging related fixes
 - UMIP fixes that should make application visible faults more debuggable
 - boot fix for weird virtualization environment

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  x86/decoder: Add new TEST instruction pattern
  x86/PCI: Remove unused HyperTransport interrupt support
  x86/umip: Fix insn_get_code_seg_params()'s return value
  x86/boot/KASLR: Remove unused variable
  x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
  x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
  x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
  x86/pkeys/selftests: Fix protection keys write() warning
  x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
  x86/mpx/selftests: Fix up weird arrays
  x86/pkeys: Update documentation about availability
  x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
  x86/smpboot: Fix __max_logical_packages estimate
  x86/topology: Avoid wasting 128k for package id array
  perf/x86/intel/uncore: Cache logical pkg id in uncore driver
  x86/acpi: Reduce code duplication in mp_override_legacy_irq()
  x86/acpi: Handle SCI interrupts above legacy space gracefully
  x86/boot: Fix boot failure when SMP MP-table is based at 0
  x86/mm: Limit mmap() of /dev/mem to valid physical addresses
  x86/selftests: Add test for mapping placement for 5-level paging
  ...

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: a documentation fix, a Sparse warning fix and a debugging
  fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix task state recording/printout
  sched/deadline: Don't use dubious signed bitfields
  sched/deadline: Fix the description of runtime accounting in the documentation

Pull perf fixes from Ingo Molnar:
 "Misc fixes: two PMU driver fixes and a memory leak fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix memory leak triggered by perf --namespace
  perf/x86/intel/uncore: Add event constraint for BDX PCU
  perf/x86/intel: Hide TSX events when RTM is not supported

Pull static key fix from Ingo Molnar:
 "Fix a boot warning related to bad init ordering of the static keys
  self-test"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  jump_label: Invoke jump_label_test() via early_initcall()