There's a check in set_secure_conn() that's supposed to ensure that SSP
is enabled before we try to request the controller to enable SC (since
SSP is a pre-requisite for it). However, this check only makes sense for
controllers actually supporting BR/EDR SC. If we have a 4.0 controller
we're only interested in the LE part of SC and should therefore not be
requiring SSP to be enabled. This patch adds an additional condition to
check for lmp_sc_capable(hdev) before requiring SSP to be enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The btusb_disconnect() callback calls hci_unregister_dev() which in turn
calls btusb_close() if the HCI device is powered. The btusb_close()
function in turn will call btusb_free_frags(). It's therefore
unnecessary to have another call to btusb_free_frags() in the
btusb_disconnect() function. Besides the redundancy the second call
seems to also cause some strange stability issues which this patch then
also fixes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When loading the Intel firmware it can happen that the firmware loading
complete vendor event arrives before the command complete event for the
last firmware fragment.

< HCI Command: Vendor (0x3f|0x0009) plen 7
        01 02 fc 03 00 00 00
> HCI Event: Vendor (0xff) plen 5
        06 00 00 00 00
> HCI Event: Command Complete (0x0e) plen 4
      Vendor (0x3f|0x0009) ncmd 31
        Status: Success (0x00)

This is mainly caused by the fact that the vendor command and its
command complete event are transported over the bulk endpoints. The
firmware loading complete event however is send over the interrupt
endpoint. So with just bad timing one event arrives before the other.

Currently the code does not account for it. There are precautions for
receiving firmware loading complete event quickly, but not for receiving
it before the command complete.

Introduce an extra flag that tracks when the firmware sending has
completed from the driver point of view and track the completion of
the firmware loading procedure with a different flag. That way the
wakeup can be handled properly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

If Secure Connections Only mode has been enabled, the it is important
to check that OOB data for P-256 values is provided. In case it is not,
then tell the remote side that no OOB data is present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When replying to the IO capability request for Secure Simple Pairing and
Secure Connections, the OOB data present fields needs to set. Instead of
making the calculation inline, split this into a separate helper
function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When Secure Connections Only mode has been enabled and remote OOB data
is requested, then only provide P-256 hash and randomizer vaulues. The
fields for P-192 hash and randomizer should be set to zero.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Until legacy SMP OOB pairing is implemented user space should be given a
clear error when trying to use it. This patch adds a corresponding check
to the Add Remote OOB Data handler function which returns "invalid
parameters" if non-zero Rand192 or Hash192 parameters were given for an
LE address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Intel Snowfield Peak devices do not come with Bluetooth firmware
loaded and thus require a full download of the operational Bluetooth
firmware when the device is connected via USB.

Snowfield Peak devices start with a bootloader mode that only accepts
a very limited set of HCI commands. The supported commands are enough
to identify the hardware and select the right firmware to load.

Previous patches to the btusb driver allow overwriting the handling
for bulk receive endpoint packets and HCI events processing. The
firmware loading makes heavy use of these new internal callbacks.

This patch also introduces additional internal states to track if the
device is in bootloader or operational mode. This allows for correct
feedback about the firmware loading procedure.

Output from /sys/kernel/debug/usb/devices for this device:

T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0a2b Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Based-on-patch-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The Dynex/Insignia USB dongles are Broadcom BCM20702B0 based and require
firmware update before operation.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=19ff ProdID=0239 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Since this is an unsual USB vendor ID (0x19ff), these dongles are added
via USB_DEVICE macro and not USB_VENDOR_AND_INTERFACE_INFO as done for
mainstream Broadcom based dongles.

The latest known working firmware is BCM20702B0_002.001.014.0527.0557.hex
which needs to be converted using hex2hcd utility and then installed
as /lib/firmware/brcm/BCM20702A0-19ff-0239.hcd to make this device fully
operational.

Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=2000 lmp_ver=06 lmp_subver=410e
Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=222d lmp_ver=06 lmp_subver=410e

With this firmware the device reports support for connectionless slave
broadcast (master and slave) feature used by 3D Glasses and TVs.

  < HCI Command: Read Local Extended Features (0x04|0x0004) plen 1
          Page: 2
  > HCI Event: Command Complete (0x0e) plen 14
        Read Local Extended Features (0x04|0x0004) ncmd 1
          Status: Success (0x00)
          Page: 2/2
          Features: 0x0f 0x00 0x00 0x00 0x00 0x00 0x00 0x00
            Connectionless Slave Broadcast - Master
            Connectionless Slave Broadcast - Slave
            Synchronization Train
            Synchronization Scan

However there are some flaws with this feature. The Set Event Mask Page 2
command is actually not supported and with that all connectionless slave
broadcast events are always enabled.

  < HCI Command: Set Event Mask Page 2 (0x03|0x0063) plen 8
          Mask: 0x00000000000f0000
            Synchronization Train Received
            Connectionless Slave Broadcast Receive
            Connectionless Slave Broadcast Timeout
            Truncated Page Complete
  > HCI Event: Command Complete (0x0e) plen 4
        Set Event Mask Page 2 (0x03|0x0063) ncmd 1
          Status: Unknown HCI Command (0x01)

In addition the Synchronization Train Received event is actually broken
on this controller. It mixes up the order of parameters. According to the
Bluetooth Core specification the fields are like this:

  struct hci_ev_sync_train_received {
          __u8     status;
          bdaddr_t bdaddr;
          __le32   offset;
          __u8     map[10];
          __u8     lt_addr;
          __le32   instant;
          __le16   interval;
          __u8     service_data;
  } __packed;

This controller however sends the service_data as 5th parameter instead
of having it as last parameter.

  struct hci_ev_sync_train_received {
          __u8     status;
          bdaddr_t bdaddr;
          __le32   offset;
          __u8     map[10];
          __u8     service_data;
          __u8     lt_addr;
          __le32   instant;
          __le16   interval;
  } __packed;

So anybody trying to use this hardware for utilizing connectionless slave
broadcast receivers (aka 3D Glasses), be warned about this shortcoming.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org

l2cap/rfcomm/sco_sock_accept() are wait loops which may acquire
sleeping locks. Since both wait loops and sleeping locks use
task_struct.state to sleep and wake, the nested sleeping locks
destroy the wait loop state.

Use the newly-minted wait_woken() and DEFINE_WAIT_FUNC() for the
wait loop. DEFINE_WAIT_FUNC() allows an alternate wake function
to be specified; in this case, the predefined scheduler function,
woken_wake_function(). This wait construct ensures wakeups will
not be missed without requiring the wait loop to set the
task state before condition evaluation. How this works:

 CPU 0                            |  CPU 1
                                  |
                                  | is <condition> set?
                                  | no
set <condition>                   |
                                  |
wake_up_interruptible             |
  woken_wake_function             |
    set WQ_FLAG_WOKEN             |
    try_to_wake_up                |
                                  | wait_woken
                                  |   set TASK_INTERRUPTIBLE
                                  |   WQ_FLAG_WOKEN? yes
                                  |   set TASK_RUNNING
                                  |
                                  | - loop -
				  |
				  | is <condition> set?
                                  | yes - exit wait loop

Fixes "do not call blocking ops when !TASK_RUNNING" warnings
in l2cap_sock_accept(), rfcomm_sock_accept() and sco_sock_accept().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

This patch converts the Set Secure Connection HCI handling to use a HCI
request instead of using a hard-coded callback in hci_event.c. This e.g.
ensures that we don't clear the flags incorrectly if something goes
wrong with the power up process (not related to a mgmt Set SC command).

The code can also be simplified a bit since only one pending Set SC
command is allowed, i.e. mgmt_pending_foreach usage is not needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Add Remote OOB Data mgmt command should allow data to be passed for
LE as well. This patch removes a left-over check for BDADDR_BREDR that
should not be there anymore.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Before doing any other verifications, the add_remote_oob_data function
should first check that the given address is valid. This patch adds such
a missing check to the beginning of the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When BR/EDR is supported by a controller, then it is required to enable
Secure Simple Pairing first before enabling the Secure Connections
feature.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When a powered on dual-mode controller has been configured to operate
as LE only with secure connections, then the BR/EDR side of things can
not be switched back on. Do reconfigure the controller it first needs
to be powered down.

The secure connections feature is implemented in the BR/EDR controller
while for LE it is implemented in the host. So explicitly forbid such
a transaction to avoid inconsistent states.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The BR/EDR Secure Connections feature should only be enabled when the
Secure Simple Pairing mode has been enabled first. However since secure
connections is feature that is valid for BR/EDR and LE, this needs
special handling.

When enabling secure connections on a LE only configured controller,
thent the BR/EDR side should not be enabled in the controller. This
patches makes the BR/EDR Secure Connections feature depending on
enabling Secure Simple Pairing mode first.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Start Discovery was reporting 0 RSSI for invalid RSSI only for
BR/EDR devices. LE devices were reported with RSSI 127.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.19+

T:  Bus=03 Lev=01 Prnt=01 Port=06 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17cf Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=54271E3298CD
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Firmware is extracted from the latest Broadcom BCM4352 Windows driver
by extracting the zip and searching the .hex file names for '17cf'.

The hex file must then be converted to hcd format using the hex2hcd
utility and then moved to /lib/firmware/brcm/.
Signed-off-by: Rick Dunn <rick@rickdunn.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Add support of 13d3:3423 device.

BugLink: https://bugs.launchpad.net/bugs/1411193

T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3423 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Merge tag 'mac80211-next-for-davem-2015-01-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Some further updates for net-next:
 * fix network-manager which was broken by the previous changes
 * fix delete-station events, which were broken by me making the
   genlmsg_end() mistake
 * fix a timer left running during suspend in some race conditions
   that would cause an annoying (but harmless) warning
 * (less important, but in the tree already) remove 80+80 MHz rate
   reporting since the spec doesn't distinguish it from 160 MHz;
   as the bitrate they're both 160 MHz bandwidth
Signed-off-by: David S. Miller <davem@davemloft.net>

My previous patch to this file changed the code to be bug-compatible
towards userspace. Unless userspace (which I wasn't able to find)
implements the dump reader by hand in a wrong way, this isn't needed.
If it uses libnl or similar code putting multiple messages into a
single SKB is far more efficient.

Change the code to do this. While at it, also clean it up and don't
use so many variables - just store the address in the callback args
directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit (3d125f9c) cause i.MX6SX sdb enet cannot work. The cause is
the commit add mdio node with un-correct phy address.

The patch just correct i.MX6sx sdb board enet phy address.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This tc action allows you to retrieve the connection tracking mark
This action has been used heavily by openwrt for a few years now.

There are known limitations currently:

doesn't work for initial packets, since we only query the ct table.
  Fine given use case is for returning packets

no implicit defrag.
  frags should be rare so fix later..

won't work for more complex tasks, e.g. lookup of other extensions
  since we have no means to store results

we still have a 2nd lookup later on via normal conntrack path.
This shouldn't break anything though since skb->nfct isn't altered.

V2:
remove unnecessary braces (Jiri)
change the action identifier to 14 (Jiri)
Fix some stylistic issues caught by checkpatch
V3:
Move module params to bottom (Cong)
Get rid of tcf_hashinfo_init and friends and conform to newer API (Cong)
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: DSA fixes for bridge and ip-autoconf

These two patches address some real world use cases of the DSA master and slave
network devices.

You have already seen patch 1 previously and you rejected it since my
explanations were not good enough to provide a justification as to why it is
useful, hopefully this time my explanation is better.

Patch 2 solves a different, yet very real problem as well at the bridge layer
when using DSA network devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA-enabled master network devices with a switch tagging protocol should
strip the protocol specific format before handing the frame over to
higher layer.

When adding such a DSA master network device as a bridge member, we go
through the following code path when receiving a frame:

__netif_receive_skb_core
	-> first ptype check against ptype_all is not returning any
	   handler for this skb

	-> check and invoke rx_handler:
		-> deliver frame to the bridge layer: br_handle_frame

DSA registers a ptype handler with the fake ETH_XDSA ethertype, which is
called *after* the bridge-layer rx_handler has run. br_handle_frame()
tries to parse the frame it received from the DSA master network device,
and will not be able to match any of its conditions and jumps straight
at the end of the end of br_handle_frame() and returns
RX_HANDLER_CONSUMED there.

Since we returned RX_HANDLER_CONSUMED, __netif_receive_skb_core() stops
RX processing for this frame and returns NET_RX_SUCCESS, so we never get
a chance to call our switch tag packet processing logic and deliver
frames to the DSA slave network devices, and so we do not get any
functional bridge members at all.

Instead of cluttering the bridge receive path with DSA-specific checks,
and rely on assumptions about how __netif_receive_skb_core() is
processing frames, we simply deny adding the DSA master network device
(conduit interface) as a bridge member, leaving only the slave DSA
network devices to be bridge members, since those will work correctly in
all circumstances.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The logic to configure a network interface for kernel IP
auto-configuration is very simplistic, and does not handle the case
where a device is stacked onto another such as with DSA. This causes the
kernel not to open and configure the master network device in a DSA
switch tree, and therefore slave network devices using this master
network devices as conduit device cannot be open.

This restriction comes from a check in net/dsa/slave.c, which is
basically checking the master netdev flags for IFF_UP and returns
-ENETDOWN if it is not the case.

Automatically bringing-up DSA master network devices allows DSA slave
network devices to be used as valid interfaces for e.g: NFS root booting
by allowing kernel IP autoconfiguration to succeed on these interfaces.

On the reverse path, make sure we do not attempt to close a DSA-enabled
device as this would implicitely prevent the slave DSA network device
from operating.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mii_check_media() does not update the link (carrier) state or log link
changes when the link mode is forced.  Drivers using the mii library
must do this themselves, but most of them do not.

Instead of changing them all, provide a sensible default behaviour
similar to mii_check_link() when the mode is forced.

via-rhine depends on it being a no-op in this case, so make its call
to mii_check_media() conditional.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Praveen Madhavan says:

====================
csiostor: Remove T4 FCoE support

We found a subtle issue with FCoE on T4 very late in the game
and decided not to productize FCoE on T4 and therefore there
are no customers that will be impacted by this change. FCoE is
supported on T5 cards.

Please apply on net-next since depends on previous commits.

Changes in v2:
  - Make the commit message more clearer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We have decided not to productize FCoE on T4.
Hence file is removed.
Signed-off-by: Praveen Madhavan <praveenm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We found a subtle issue with FCoE on T4 very late in the game
and decided not to productize FCoE on T4 and therefore there
are no customers that will be impacted by this change. Hence
T4 FCoE support is removed. FCoE supported only on T5 cards.

changes in v2:
  - Make the commit message more clearer.
Signed-off-by: Praveen Madhavan <praveenm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Murali Karicheri says:

====================
net: Add Keystone NetCP ethernet driver support

The Network Coprocessor (NetCP) is a hardware accelerator that processes
Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsystem with a ethernet
switch sub-module to send and receive packets. NetCP also includes a packet
accelerator (PA) module to perform packet classification operations such as
header matching, and packet modification operations such as checksum
generation. NetCP can also optionally include a Security Accelerator(SA)
capable of performing IPSec operations on ingress/egress packets.

Keystone SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which
includes a 3-port Ethernet switch sub-module capable of 10Gb/s and
1Gb/s rates per Ethernet port.

Both GBE and XGBE network processors supported using common driver. It
is also designed to handle future variants of NetCP.

version history
---------------
v7->v8

 - Reworked comments against v7, related to checker warning.
 - Patch 2/4 that has all of the driver code in v7 is now split into 3
   patches based on functionality so that we have 3 smaller patches
   review instead of a big patch.
 - Patch for MAINTAINER is merged to 2/4 along with netcp core driver
 - Separate patch (3/4) for 1G and  (4/4) for 10G
 - Removed big endian support for initial version (will add it later)

v6->v7
 - Fixed some minor documentation error and also modified the netcp driver
   to fix the set* functions to include correct le/be macros.

v5->v6
 - updated version after incorporating comments [6] from David Miller,
   David Laight & Geert Uytterhoeven on v5. I would like get this in
   for v3.19 merge window if the latest version is acceptable.

v4->v5
 - Sorry to spin v5 quickly but I missed few check-patch warnings which
   were pointed by Joe Perches(thanks). I folded his changes [5] along with
   few more check-patch warning fixes. I would like get this in for v3.18
   merge window if David is happy with this version.

v3->v4
 - Couple of fixes in in error path as pointed [4] out by David. Rest of
   the patches are unchanged from v3.

v2->v3
 - Update v3 after incorporating Jamal and David Miller's comment/suggestion
   from earlier versions [1] [2].  After per the discussion here [3], the
   controversial custom exports have been dropped now. And for future
   future offload support additions, we will plug into generic frameworks
   as an when they are available.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enhances the NetCP gbe driver to support 10GbE subsystem
available in Keystone NetCP. The 3-port 10GbE switch sub-module contains
the following components:- 10GbE Switch, MDIO Module, 2 PCS-R Modules
(10GBase-R) and 2 SGMII modules (10/100/1000Base-T). The GBE driver
together with netcp core driver provides support for 10G Ethernet
on Keystone SoCs.

10GbE hardware spec is available at

http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=spruhj5&fileType=pdf

 Cc: David Miller <davem@davemloft.net>
 Cc: Rob Herring <robh+dt@kernel.org>
 Cc: Grant Likely <grant.likely@linaro.org>
 Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
 Cc: Pawel Moll <pawel.moll@arm.com>
 Cc: Mark Rutland <mark.rutland@arm.com>
 Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
 Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add support for 1G Ethernet driver based on Keystone
NetCP hardware. The gigabit Ethernet (GbE) switch subsystem is one of the main
components of the network coprocessor (NETCP) peripheral. The purpose of the
gigabit Ethernet switch subsystem in the NETCP is to provide an interface to
transfer data between the host device and another connected device in
compliance with the Ethernet protocol. GbE consists of 5 port Ethernet Switch
module, 4 Serial Gigabit Media Independent Interface (SGMII) modules, MDIO
module and SerDes.

Driver for 5 port GbE switch and SGMII module is added in this patch. These
hardware modules along with netcp core driver provides Network driver functions
for 1G Ethernet.

Detailed hardware spec is available at

http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf

 Cc: David Miller <davem@davemloft.net>
 Cc: Rob Herring <robh+dt@kernel.org>
 Cc: Grant Likely <grant.likely@linaro.org>
 Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
 Cc: Pawel Moll <pawel.moll@arm.com>
 Cc: Mark Rutland <mark.rutland@arm.com>
 Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
 Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The network coprocessor (NetCP) is a hardware accelerator available in
Keystone SoCs that processes Ethernet packets. NetCP consists of following
hardware components

 1 Gigabit Ethernet (GbE) subsystem with a Ethernet switch sub-module to
   send and receive packets.
 2 Packet Accelerator (PA) module to perform packet classification
   operations such as header matching, and packet modification operations
   such as checksum generation.
 3 Security Accelerator(SA) capable of performing IPSec operations on
   ingress/egress packets.
 4 An optional 10 Gigabit Ethernet Subsystem (XGbE) which includes a
   3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates
   per Ethernet port.
 5 Packet DMA and Queue Management Subsystem (QMSS) to enqueue and dequeue
   packets and DMA the packets between memory and NetCP hardware components
   described above.

NetCP core driver make use of the Keystone Navigator driver API to allocate
DMA channel for the Ethenet device and to handle packet queue/de-queue,
Please refer API's in include/linux/soc/ti/knav_dma.h and
drivers/soc/ti/knav_qmss.h for details.

NetCP driver consists of NetCP core driver and at a minimum Gigabit
Ethernet (GBE) module (1) driver to implement the Network device function.
Other modules (2,3) can be optionally added to achieve supported hardware
acceleration function. The initial version of the driver include NetCP
core driver and GBE driver modules.

Please refer Documentation/devicetree/bindings/net/keystone-netcp.txt
for design of the driver.

 Cc: David Miller <davem@davemloft.net>
 Cc: Rob Herring <robh+dt@kernel.org>
 Cc: Grant Likely <grant.likely@linaro.org>
 Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
 Cc: Pawel Moll <pawel.moll@arm.com>
 Cc: Mark Rutland <mark.rutland@arm.com>
 Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
 Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Wingman Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The network coprocessor (NetCP) is a hardware accelerator that processes
Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsystem with a ethernet
switch sub-module to send and receive packets. NetCP also includes a packet
accelerator (PA) module to perform packet classification operations such as
header matching, and packet modification operations such as checksum
generation. NetCP can also optionally include a Security Accelerator(SA)
capable of performing IPSec operations on ingress/egress packets.

Keystone SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which
includes a 3-port Ethernet switch sub-module capable of 10Gb/s and
1Gb/s rates per Ethernet port.

NetCP Subsystem device tree layout looks something like below:

-----------------------------
  NetCP subsystem(10G or 1G)
-----------------------------
	|
	|-> NetCP Devices ->	|
	|			|-> GBE/XGBE Switch
	|			|
	|			|-> Packet Accelerator
	|			|
	|			|-> Security Accelerator
	|
	|
	|
	|-> NetCP Interfaces ->	|
				|-> Ethernet Port 0
				|
				|-> Ethernet Port 1
				|
				|-> Ethernet Port 2
				|
				|-> Ethernet Port 3

Common driver supports GBE as well XGBE network processors.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: David Miller <davem@davemloft.net>
Cc: Santosh Shilimkar <santosh.shilimkar@kernel.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit c03abd84 (net: ethernet: cpsw: don't requests IRQs we don't
use) left one build breakage when NET_POLL_CONTROLLER is enabled.

Fix this build break by referring to the correct irqs_table array.

Fixes: c03abd84 (net: ethernet: cpsw: don't requests IRQs we don't use)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'link_netns'

Nicolas Dichtel says:

====================
netns: allow to identify peer netns

The goal of this serie is to be able to multicast netlink messages with an
attribute that identify a peer netns.
This is needed by the userland to interpret some information contained in
netlink messages (like IFLA_LINK value, but also some other attributes in case
of x-netns netdevice (see also
http://thread.gmane.org/gmane.linux.network/315933/focus=316064 and
http://thread.gmane.org/gmane.linux.kernel.containers/28301/focus=4239)).

Ids of peer netns can be set by userland via a new rtnl cmd RTM_NEWNSID. When
the kernel needs an id for a peer (for example when advertising a new x-netns
interface via netlink), if the user didn't allocate an id, one will be
automatically allocated.
These ids are stored per netns and are local (ie only valid in the netns where
they are set). To avoid allocating an int for each peer netns, I use
idr_for_each() to retrieve the id of a peer netns. Note that it will be possible
to add a table (struct net -> id) later to optimize this lookup if needed.

Patch 1/4 introduces the rtnetlink API mechanism to set and get these ids.
Patch 2/4 and 3/4 implements an example of how to use these ids when advertising
information about a x-netns interface.
And patch 4/4 shows that the netlink messages can be symetric between a GET and
a SET.

iproute2 patches are available, I can send them on demand.

Here is a small screenshot to show how it can be used by userland.

$ ip netns add foo
$ ip netns del foo
$ ip netns
$ touch /var/run/netns/init_net
$ mount --bind /proc/1/ns/net /var/run/netns/init_net
$ ip netns add foo
$ ip -n foo netns
foo
init_net
$ ip -n foo netns set init_net 0
$ ip -n foo netns set foo 1

$ ip netns
foo
init_net
$ ip -n foo netns
foo (id: 1)
init_net (id: 0)

$ ip -n foo link add ipip1 link-netnsid 0 type ipip remote 10.16.0.121 local 10.16.0.249
$ ip -n foo link ls ipip1
6: ipip1@NONE: <POINTOPOINT,NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
    link/ipip 10.16.0.249 peer 10.16.0.121 link-netnsid 0

$ ip netns
foo
init_net
$ ip -n foo link add ipip2 type ipip remote 10.16.0.121 local 10.16.0.249
$ ip -n foo link set ipip2 netns init_net
$ ip link ls ipip2
7: ipip2@NONE: <POINTOPOINT,NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
    link/ipip 10.16.0.249 peer 10.16.0.121 link-netnsid 0
$ ip netns
foo (id: 0)
init_net

v4 -> v5:
  use rtnetlink instead of genetlink
  allocate automatically an id if user didn't assign one
  rename include/uapi/linux/netns.h to include/uapi/linux/net_namespace.h
  add vxlan in patch #3

RFCv3 -> v4:
  rebase on net-next
  add copyright text in the new netns.h file

RFCv2 -> RFCv3:
  ids are now defined by userland (via netlink). Ids are stored in each netns
  (and they are local to this netns).
  add get_link_net support for ip6 tunnels
  netnsid is now a s32 instead of a u32

RFCv1 -> RFCv2:
  remove useless ()
  ids are now stored in the user ns. It's possible to get an id for a peer netns
  only if the current netns and the peer netns have the same user ns parent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the ability to create a netdevice in a specified netns and
then move it into the final netns. In fact, it allows to have a symetry between
get and set rtnl messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new attribute (IFLA_LINK_NETNSID) which contains the 'link'
netns id when this netns is different from the netns where the interface
stands (for example for x-net interfaces like ip tunnels).
With this attribute, it's possible to interpret correctly all advertised
information (like IFLA_LINK, etc.).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>