For PHYs that call rtl821x_probe() where an external clock can be
configured, make sure that the clock is disabled
when ->suspend() is called and enabled on resume.

The PHY_ALWAYS_CALL_SUSPEND is added to ensure that the suspend function
is actually always called.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ethern PHYs can have external an clock that needs to be activated before
communicating with the PHY.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases, the PHY can use an external clock source instead of a
crystal.

Add an optional clock in the phy node to make sure that the clock source
is enabled, if specified, before probing.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocate the size of rx indirection table dynamically in netvsc
from the value of size provided by OID_GEN_RECEIVE_SCALE_CAPABILITIES
query instead of using a constant value of ITAB_NUM.
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Tested-on: Ubuntu22 (azure VM, SKU size: Standard_F72s_v2)
Testcases:
1. ethtool -x eth0 output
2. LISA testcase:PERF-NETWORK-TCP-THROUGHPUT-MULTICONNECTION-NTTTCP-Synthetic
3. LISA testcase:PERF-NETWORK-TCP-THROUGHPUT-MULTICONNECTION-NTTTCP-SRIOV
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace these open-code bearer rcu_dereference access with bearer_get(),
like other places in bearer.c. While at it, also use tipc_net() instead
of net_generic(net, tipc_net_id) to get "tn" in bearer.c.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Link: https://lore.kernel.org/r/1072588a8691f970bda950c7e2834d1f2983f58e.1685976044.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Guillaume Nault says:

====================
ipv4: Remove RT_CONN_FLAGS() calls in flowi4_init_output().

Remove a few RT_CONN_FLAGS() calls used inside flowi4_init_output().
These users can be easily converted to set the scope properly, instead
of overloading the tos parameter with scope information as done by
RT_CONN_FLAGS().

The objective is to eventually remove RT_CONN_FLAGS() entirely, which
will then allow to also remove RTO_ONLINK and to finally convert
->flowi4_tos to dscp_t.
====================

Link: https://lore.kernel.org/r/cover.1685999117.git.gnault@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

RT_CONN_FLAGS(sk) overloads flowi4_tos with the RTO_ONLINK bit when
sk has the SOCK_LOCALROUTE flag set. This allows
ip_route_output_key_hash() to eventually adjust flowi4_scope.

Instead of relying on special handling of the RTO_ONLINK bit, we can
just set the route scope correctly. This will eventually allow to avoid
special interpretation of tos variables and to convert ->flowi4_tos to
dscp_t.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

RT_CONN_FLAGS(sk) overloads the tos parameter with the RTO_ONLINK bit
when sk has the SOCK_LOCALROUTE flag set. This is only useful for
ip_route_output_key_hash() to eventually adjust the route scope.

Let's drop RTO_ONLINK and set the correct scope directly to avoid this
special case in the future and to allow converting ->flowi4_tos to
dscp_t.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Robert Hancock says:

====================
Move KSZ9477 errata handling to PHY driver

Patches to move handling for KSZ9477 PHY errata register fixes from
the DSA switch driver into the corresponding PHY driver, for more
proper layering and ordering.
====================

Link: https://lore.kernel.org/r/20230605153943.1060444-1-robert.hancock@calian.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The KSZ9477 PHY errata handling code has now been moved into the Micrel
PHY driver, so it is no longer needed inside the DSA switch driver.
Remove it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The ksz9477 DSA switch driver is currently updating some MMD registers
on the internal port PHYs to address some chip errata. However, these
errata are really a property of the PHY itself, not the switch they are
part of, so this is kind of a layering violation. It makes more sense for
these writes to be done inside the driver which binds to the PHY and not
the driver for the containing device.

This also addresses some issues where the ordering of when these writes
are done may have been incorrect, causing the link to erratically fail to
come up at the proper speed or at all. Doing this in the PHY driver
during config_init ensures that they happen before anything else tries to
change the state of the PHY on the port.

The new code also ensures that autonegotiation is disabled during the
register writes and re-enabled afterwards, as indicated by the latest
version of the errata documentation from Microchip.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
tools: ynl: user space C

Use the code gen which is already in tree to generate a user space
library for a handful of simple families. I find YNL C quite useful
in some WIP projects, and I think others may find it useful, too.
I was hoping someone will pick this work up and finish it...
but it seems that Python YNL has largely stolen the thunder.
Python may not be great for selftest, tho, and actually this lib
is more fully-featured. The Python script was meant as a quick demo,
funny how those things go.

v2: https://lore.kernel.org/all/20230604175843.662084-1-kuba@kernel.org/
v1: https://lore.kernel.org/all/20230603052547.631384-1-kuba@kernel.org/
====================

Link: https://lore.kernel.org/r/20230605190108.809439-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add a sample application using the C library.
My main goal is to make writing selftests easier but until
I have some of those ready I think it's useful to show off
the functionality and let people poke and tinker.

Sample outputs - dump:

$ ./netdev
Select ifc ($ifindex; or 0 = dump; or -2 ntf check): 0
      lo[1]	0:
  enp1s0[2]	23: basic redirect rx-sg

Notifications (watching veth pair getting added and deleted):

$ ./netdev
Select ifc ($ifindex; or 0 = dump; or -2 ntf check): -2
[53]	0: (ntf: dev-add-ntf)
[54]	0: (ntf: dev-add-ntf)
[54]	23: basic redirect rx-sg (ntf: dev-change-ntf)
[53]	23: basic redirect rx-sg (ntf: dev-change-ntf)
[53]	23: basic redirect rx-sg (ntf: dev-del-ntf)
[54]	23: basic redirect rx-sg (ntf: dev-del-ntf)
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Generate the code for netdev and fou families. They are simple
and already supported by the code gen.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add "fixed" part of the user space Netlink Spec-based library.
This will get linked with the protocol implementations to form
a full API.
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Do not print empty lines before closing brackets.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of its intention to define PPPOE_HASH_BITS_1, commit 96ba44c6
("net/pppoe: make number of hash bits configurable") actually defined
config PPPOE_HASH_BITS_2 twice in the ppp's Kconfig file due to a quick
typo with the numbers.

Fix the typo and define PPPOE_HASH_BITS_1.

Fixes: 96ba44c6 ("net/pppoe: make number of hash bits configurable")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jaco Kroon <jaco@uls.co.za>
Link: https://lore.kernel.org/r/20230605072743.11247-1-lukas.bulwahn@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Since hex_to_bin() is provided by hex.h there is no need to require
kernel.h. Replace the latter by the former and add missing export.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230604132858.6650-1-andriy.shevchenko@linux.intel.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The GRO control block (NAPI_GRO_CB) is currently at its maximum size.
This commit reduces its size by putting two groups of fields that are
used only at different times into a union.

Specifically, the fields frag0 and frag0_len are the fields that make up
the frag0 optimisation mechanism, which is used during the initial
parsing of the SKB.

The fields last and age are used after the initial parsing, while the
SKB is stored in the GRO list, waiting for other packets to arrive.

There was one location in dev_gro_receive that modified the frag0 fields
after setting last and age. I changed this accordingly without altering
the code behaviour.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230601161407.GA9253@debianSigned-off-by: Paolo Abeni <pabeni@redhat.com>

David Howells says:

====================
splice, net: Handle MSG_SPLICE_PAGES in AF_KCM

Here are patches to make AF_KCM handle the MSG_SPLICE_PAGES internal
sendmsg flag.  MSG_SPLICE_PAGES is an internal hint that tells the protocol
that it should splice the pages supplied if it can.  Its sendpage
implementation is then turned into a wrapper around that.

Does anyone actually use AF_KCM?  Upstream it has some issues.  It doesn't
seem able to handle a "message" longer than 113920 bytes without jamming
and doesn't handle the client termination once it is jammed.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=51c78a4d532efe9543a4df019ff405f05c6157f6 # part 1
Link: https://lore.kernel.org/r/20230524144923.3623536-1-dhowells@redhat.com/ # v1
====================

Link: https://lore.kernel.org/r/20230531110423.643196-1-dhowells@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Convert kcm_sendpage() to use sendmsg() with MSG_SPLICE_PAGES rather than
directly splicing in the pages itself.

This allows ->sendpage() to be replaced by something that can handle
multiple multipage folios in a single transaction.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Tom Herbert <tom@herbertland.com>
cc: Tom Herbert <tom@quantonium.net>
cc: Cong Wang <cong.wang@bytedance.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make AF_KCM sendmsg() support MSG_SPLICE_PAGES.  This causes pages to be
spliced from the source iterator if possible.

This allows ->sendpage() to be replaced by something that can handle
multiple multipage folios in a single transaction.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Tom Herbert <tom@herbertland.com>
cc: Tom Herbert <tom@quantonium.net>
cc: Cong Wang <cong.wang@bytedance.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5-updates-2023-05-31

net/mlx5: Support 4 ports VF LAG, part 1/2

This series continues the series[1] "Support 4 ports HCAs LAG mode"
by Mark Bloch. This series adds support for 4 ports VF LAG (single FDB
E-Switch).

This series of patches focuses on refactoring different sections of the
code that make assumptions about VF LAG supporting only two ports. For
instance, it assumes that each device can only have one peer.

Patches 1-5:
- Refactor ETH handling of TC rules of eswitches with peers.
Patch 6:
- Refactors peer miss group table.
Patches 7-9:
- Refactor single FDB E-Switch creation.
Patch 10:
- Refactor the DR layer.
Patches 11-14:
- Refactors devcom layer.

Next series will refactor LAG layer and enable 4 ports VF LAG.
This series specifically allows HCAs with 4 ports to create a VF LAG
with only 4 ports. It is not possible to create a VF LAG with 2 or 3
ports using HCAs that have 4 ports.

Currently, the Merged E-Switch feature only supports HCAs with 2 ports.
However, upcoming patches will introduce support for HCAs with 4 ports.

In order to activate VF LAG a user can execute:

devlink dev eswitch set pci/0000:08:00.0 mode switchdev
devlink dev eswitch set pci/0000:08:00.1 mode switchdev
devlink dev eswitch set pci/0000:08:00.2 mode switchdev
devlink dev eswitch set pci/0000:08:00.3 mode switchdev
ip link add name bond0 type bond
ip link set dev bond0 type bond mode 802.3ad
ip link set dev eth2 master bond0
ip link set dev eth3 master bond0
ip link set dev eth4 master bond0
ip link set dev eth5 master bond0

Where eth2, eth3, eth4 and eth5 are net-interfaces of pci/0000:08:00.0
pci/0000:08:00.1 pci/0000:08:00.2 pci/0000:08:00.3 respectively.

User can verify LAG state and type via debugfs:
/sys/kernel/debug/mlx5/0000\:08\:00.0/lag/state
/sys/kernel/debug/mlx5/0000\:08\:00.0/lag/type

[1]
https://lore.kernel.org/netdev/20220510055743.118828-1-saeedm@nvidia.com/

* tag 'mlx5-updates-2023-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5: Devcom, extend mlx5_devcom_send_event to work with more than two devices
  net/mlx5: Devcom, introduce devcom_for_each_peer_entry
  net/mlx5: E-switch, mark devcom as not ready when all eswitches are unpaired
  net/mlx5: Devcom, Rename paired to ready
  net/mlx5: DR, handle more than one peer domain
  net/mlx5: E-switch, generalize shared FDB creation
  net/mlx5: E-switch, Handle multiple master egress rules
  net/mlx5: E-switch, refactor FDB miss rule add/remove
  net/mlx5: E-switch, enlarge peer miss group table
  net/mlx5e: Handle offloads flows per peer
  net/mlx5e: en_tc, re-factor query route port
  net/mlx5e: rep, store send to vport rules per peer
  net/mlx5e: tc, Refactor peer add/del flow
  net/mlx5e: en_tc, Extend peer flows to a list
====================

Link: https://lore.kernel.org/r/20230602191301.47004-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Andrzej Hajda says:

====================
drm/i915: use ref_tracker library for tracking wakerefs

This is reviewed series of ref_tracker patches, ready to merge
via network tree, rebased on net-next/main.
i915 patches will be merged later via intel-gfx tree.
====================

Merge on top of an -rc tag in case it's needed in another tree.

Link: https://lore.kernel.org/r/20230224-track_gt-v9-0-5b47a33f55d1@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Library can handle allocation failures. To avoid allocation warnings
__GFP_NOWARN has been added everywhere. Moreover GFP_ATOMIC has been
replaced with GFP_NOWAIT in case of stack allocation on tracker free
call.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Similar to stack_(depot|trace)_snprint the patch
adds helper to printing stats to memory buffer.
It will be helpful in case of debugfs.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In case the library is tracking busy subsystem, simply
printing stack for every active reference will spam log
with long, hard to read, redundant stack traces. To improve
readabilty following changes have been made:
- reports are printed per stack_handle - log is more compact,
- added display name for ref_tracker_dir - it will differentiate
  multiple subsystems,
- stack trace is printed indented, in the same printk call,
- info about dropped references is printed as well.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

To have reliable detection of leaks, caller must be able to check under
the same lock both: tracked counter and the leaks. dir.lock is natural
candidate for such lock and unlocked print helper can be called with this
lock taken.
As a bonus we can reuse this helper in ref_tracker_dir_exit.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Petr Machata says:

====================
mlxsw, selftests: Cleanups

This patchset consolidates a number of disparate items that can all be
considered cleanups. They are all related to mlxsw in that they are
directly in mlxsw code, or in selftests that mlxsw heavily uses.

- patch #1 fixes a comment, patch #2 propagates an extack

- patches #3 and #4 tweak several loops to query a resource once and cache
  in a local variable instead of querying on each iteration

- patches #5 and #6 fix selftest diagrams, and #7 adds a missing diagram
  into an existing test

- patch #8 disables a PVID on a bridge in a selftest that should not need
  said PVID
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When everything is configured, VLAN membership on the bridge in this
selftest are as follows:

    # bridge vlan show
    port              vlan-id
    swp2              1 PVID Egress Untagged
                      555
    br1               1 Egress Untagged
                      555 PVID Egress Untagged

Note that it is possible for untagged traffic to just flow through as VLAN
1, instead of using VLAN 555 as intended by the test. This configuration
seems too close to "works by accident", and it would be better to just shut
out VLAN 1 altogether.

To that end, configure vlan_default_pvid of 0:

    # bridge vlan show
    port              vlan-id
    swp2              555
    br1               555 PVID Egress Untagged
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a topology diagram to this selftest to make the configuration easier to
understand.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The topology diagram implies that $swp1 and $swp2 are members of the bridge
br0, when in fact only their uppers, $swp1.10 and $swp2.10 are. Adjust the
diagram.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The topology diagram implies that $swp1 and $swp2 are members of the bridge
br0, when in fact only their uppers, $swp1.10 and $swp2.10 are. Adjust the
diagram.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MLXSW_CORE_RES_GET involves a call to spectrum_core, a separate module.
Instead of making the call on every iteration, cache it up front, and use
the value.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MLXSW_CORE_RES_GET involves a call to spectrum_core, a separate module.
Instead of making the call on every iteration, cache it up front, and use
the value.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 26029225 ("mlxsw: spectrum_router: Propagate extack
further"), the mlxsw_sp_rif_ops.configure callback got a new argument,
extack. However the callbacks that deal with tunnel configuration,
mlxsw_sp1_rif_ipip_lb_configure() and mlxsw_sp2_rif_ipip_lb_configure(),
were never updated to pass the parameter further. Do that now.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"Reserved for X" usually means that only X is supposed to use a given
object. Here, it is used in the sense that X should consider the object
"reserved", as in "restricted".

Replace the comment simply by "X", with the implication that that's where
the field is used.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
convert sja1105 xpcs creation and remove xpcs_create

This series of three patches converts sja1105 to use the newly
provided xpcs_create_mdiodev(), and as there become no users of
xpcs_create(), removes this function from the global namespace to
discourage future direct use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There are now no callers of xpcs_create(), so let's remove it from
public view to discourage future direct usage.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the new xpcs_create_mdiodev() creator, which simplifies the
creation and destruction of the mdio device associated with xpcs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>