The strlcpy should not be used because it doesn't limit the source
length. Preferred is strscpy.
Signed-off-by: XueBing Chen <chenxuebing@jari.cn>
Link: https://lore.kernel.org/r/2d2fcbf7.e33.181eda8e70e.Coremail.chenxuebing@jari.cnSigned-off-by: Johannes Berg <johannes.berg@intel.com>

In AP mode, multicast traffic is handled very differently from normal traffic,
especially if at least one client is in powersave mode.
This means that multicast packets can be buffered a lot longer than normal
unicast packets, and can eat up the AQL budget very quickly because of the low
data rate.
Along with the recent change to maintain a global PHY AQL limit, this can lead
to significant latency spikes for unicast traffic.

Since queueing multicast to hardware is currently not constrained by AQL limits
anyway, let's just exclude it from the AQL pending airtime calculation entirely.

Fixes: 8e4bac06 ("wifi: mac80211: add a per-PHY AQL limit to improve fairness")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220713083444.86129-1-nbd@nbd.nameSigned-off-by: Johannes Berg <johannes.berg@intel.com>

We won't really have enough skbs to need a 64-bit cookie,
and on 32-bit platforms storing the 64-bit cookie into the
void *rate_driver_data doesn't work anyway. Switch back to
using just a 32-bit cookie and uintptr_t for the type to
avoid compiler warnings about all this.

Fixes: 4ee186fa ("wifi: mac80211_hwsim: fix race condition in pending packet")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Remove a variable here that was now set but never used.

Fixes: f276e20b ("wifi: mac80211: move interface config to new struct")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Saeed Mahameed says:

====================
mlx5-updates-2022-07-13

1) Support 802.1ad for bridge offloads

Vlad Buslov Says:
=================

Current mlx5 bridge VLAN offload implementation only supports 802.1Q VLAN
Ethernet protocol. That protocol type is assumed by default and
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification is ignored.

In order to support dynamically setting VLAN protocol handle
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification by flushing FDB and
re-creating VLAN modify header actions with a new protocol. Implement support
for 802.1ad protocol by saving the current VLAN protocol to per-bridge variable
and re-create the necessary flow groups according to its current value (either
use cvlan or svlan flow fields).
==================

2) debugfs to count ongoing FW commands

3) debugfs to query eswitch vport firmware diagnostic counters

4) Add missing meter configuration in flow action

5) Some misc cleanup

* tag 'mlx5-updates-2022-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5e: Remove the duplicating check for striding RQ when enabling LRO
  net/mlx5e: Move the LRO-XSK check to mlx5e_fix_features
  net/mlx5e: Extend flower police validation
  net/mlx5e: configure meter in flow action
  net/mlx5e: Removed useless code in function
  net/mlx5: Bridge, implement QinQ support
  net/mlx5: Bridge, implement infrastructure for VLAN protocol change
  net/mlx5: Bridge, extract VLAN push/pop actions creation
  net/mlx5: Bridge, rename filter fg to vlan_filter
  net/mlx5: Bridge, refactor groups sizes and indices
  net/mlx5: debugfs, Add num of in-use FW command interface slots
  net/mlx5: Expose vnic diagnostic counters for eswitch managed vports
  net/mlx5: Use software VHCA id when it's supported
  net/mlx5: Introduce ifc bits for using software vhca id
  net/mlx5: Use the bitmap API to allocate bitmaps
====================

Link: https://lore.kernel.org/r/20220713225859.401241-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jiri Pirko says:

====================
net: devlink: couple of trivial fixes

Just a couple of trivial fixes I found on the way.
====================

Link: https://lore.kernel.org/r/20220713141853.2992014-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Return directly without intermediate value store at the end of
devlink_port_new_notify() function.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix the typo in a name of devlink_port_new_notifiy() function.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The return value is not used, so change the return value type to void.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

include/net/sock.h
  310731e2 ("net: Fix data-races around sysctl_mem.")
  e70f3c70 ("Revert "net: set SK_MEM_QUANTUM to 4096"")
https://lore.kernel.org/all/20220711120211.7c8b7cba@canb.auug.org.au/

net/ipv4/fib_semantics.c
  747c1430 ("ip: fix dflt addr selection for connected nexthop")
  d62607c3 ("net: rename reference+tracking helpers")

net/tls/tls.h
include/net/tls.h
  3d8c51b2 ("net/tls: Check for errors in tls_device_init")
  58790314 ("tls: create an internal header")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Clang warns:

  arch/x86/kernel/cpu/bugs.c:58:21: error: section attribute is specified on redeclared variable [-Werror,-Wsection]
  DEFINE_PER_CPU(u64, x86_spec_ctrl_current);
                      ^
  arch/x86/include/asm/nospec-branch.h:283:12: note: previous declaration is here
  extern u64 x86_spec_ctrl_current;
             ^
  1 error generated.

The declaration should be using DECLARE_PER_CPU instead so all
attributes stay in sync.

Cc: stable@vger.kernel.org
Fixes: fc02735b ("KVM: VMX: Prevent guest RSB poisoning attacks with eIBRS")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from netfilter, bpf and wireless.

  Still no major regressions, the release continues to be calm. An
  uptick of fixes this time around due to trivial data race fixes and
  patches flowing down from subtrees.

  There has been a few driver fixes (particularly a few fixes for false
  positives due to 66e4c8d9 which went into -next in May!) that make
  me worry the wide testing is not exactly fully through.

  So "calm" but not "let's just cut the final ASAP" vibes over here.

  Current release - regressions:

   - wifi: rtw88: fix write to const table of channel parameters

  Current release - new code bugs:

   - mac80211: add gfp_t arg to ieeee80211_obss_color_collision_notify

   - mlx5:
      - TC, allow offload from uplink to other PF's VF
      - Lag, decouple FDB selection and shared FDB
      - Lag, correct get the port select mode str

   - bnxt_en: fix and simplify XDP transmit path

   - r8152: fix accessing unset transport header

  Previous releases - regressions:

   - conntrack: fix crash due to confirmed bit load reordering (after
     atomic -> refcount conversion)

   - stmmac: dwc-qos: disable split header for Tegra194

  Previous releases - always broken:

   - mlx5e: ring the TX doorbell on DMA errors

   - bpf: make sure mac_header was set before using it

   - mac80211: do not wake queues on a vif that is being stopped

   - mac80211: fix queue selection for mesh/OCB interfaces

   - ip: fix dflt addr selection for connected nexthop

   - seg6: fix skb checksums for SRH encapsulation/insertion

   - xdp: fix spurious packet loss in generic XDP TX path

   - bunch of sysctl data race fixes

   - nf_log: incorrect offset to network header

  Misc:

   - bpf: add flags arg to bpf_dynptr_read and bpf_dynptr_write APIs"

* tag 'net-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
  nfp: flower: configure tunnel neighbour on cmsg rx
  net/tls: Check for errors in tls_device_init
  MAINTAINERS: Add an additional maintainer to the AMD XGBE driver
  xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
  selftests/net: test nexthop without gw
  ip: fix dflt addr selection for connected nexthop
  net: atlantic: remove aq_nic_deinit() when resume
  net: atlantic: remove deep parameter on suspend/resume functions
  sfc: fix kernel panic when creating VF
  seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
  seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
  seg6: fix skb checksum evaluation in SRH encapsulation/insertion
  sfc: fix use after free when disabling sriov
  net: sunhme: output link status with a single print.
  r8152: fix accessing unset transport header
  net: stmmac: fix leaks in probe
  net: ftgmac100: Hold reference returned by of_get_child_by_name()
  nexthop: Fix data-races around nexthop_compat_mode.
  ipv4: Fix data-races around sysctl_ip_dynaddr.
  tcp: Fix a data-race around sysctl_tcp_ecn_fallback.
  ...

Pull cifs fixes from Steve French:
 "Three smb3 client fixes:

   - two multichannel fixes: fix a potential deadlock freeing a channel,
     and fix a race condition on failed creation of a new channel

   - mount failure fix: work around a server bug in some common older
     Samba servers by avoiding padding at the end of the negotiate
     protocol request"

* tag '5.19-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: workaround negprot bug in some Samba servers
  cifs: remove unnecessary locking of chan_lock while freeing session
  cifs: fix race condition with delayed threads

Pull nfsd fixes from Chuck Lever:
 "Notable regression fixes:

   - Enable SETATTR(time_create) to fix regression with Mac OS clients

   - Fix a lockd crasher and broken NLM UNLCK behavior"

* tag 'nfsd-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
  lockd: fix nlm_close_files
  lockd: set fl_owner when unlocking files
  NFSD: Decode NFSv4 birth time attribute

Merge tag 'integrity-v5.19-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity

Pull integrity fixes from Mimi Zohar:
 "Here are a number of fixes for recently found bugs.

  Only 'ima: fix violation measurement list record' was introduced in
  the current release. The rest address existing bugs"

* tag 'integrity-v5.19-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
  ima: Fix potential memory leak in ima_init_crypto()
  ima: force signature verification when CONFIG_KEXEC_SIG is configured
  ima: Fix a potential integer overflow in ima_appraise_measurement
  ima: fix violation measurement list record
  Revert "evm: Fix memleak in init_desc"

Pull ARM fixes from Russell King:

 - quieten the spectre-bhb prints

 - mark flattened device tree sections as shareable

 - remove some obsolete CPU domain code and help text

 - fix thumb unaligned access abort emulation

 - fix amba_device_add() refcount underflow

 - fix literal placement

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9208/1: entry: add .ltorg directive to keep literals in range
  ARM: 9207/1: amba: fix refcount underflow if amba_device_add() fails
  ARM: 9214/1: alignment: advance IT state after emulating Thumb instruction
  ARM: 9213/1: Print message about disabled Spectre workarounds only once
  ARM: 9212/1: domain: Modify Kconfig help text
  ARM: 9211/1: domain: drop modify_domain()
  ARM: 9210/1: Mark the FDT_FIXED sections as shareable
  ARM: 9209/1: Spectre-BHB: avoid pr_info() every time a CPU comes out of idle

The UML function names to_virt() and to_phys() are exposed by UML
headers, and are very generic and may be defined by drivers.  As it
turns out, commit 9409c9b6 ("pmem: refactor pmem_clear_poison()")
did exactly that.

This results in build errors such as the following when trying to build
um:allmodconfig:

  drivers/nvdimm/pmem.c: In function ‘pmem_dax_zero_page_range’:
  ./arch/um/include/asm/page.h:105:20: error: too few arguments to function ‘to_phys’
    105 | #define __pa(virt) to_phys((void *) (unsigned long) (virt))
        |                    ^~~~~~~

Use less generic function names for the um specific to_phys() and
to_virt() functions to fix the problem and to avoid similar problems in
the future.

Fixes: 9409c9b6 ("pmem: refactor pmem_clear_poison()")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sound fixes from Takashi Iwai:
 "Hopefully the last one for 5.19. This became bigger than wished, but
  all changes are pretty device-specific small fixes, which look less
  worrisome.

  The majority of changes are about various ASoC fixes, while the usual
  HD-audio quirks are included as well"

* tag 'sound-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (28 commits)
  ALSA: hda/realtek - Enable the headset-mic on a Xiaomi's laptop
  ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc221
  ALSA: hda/realtek: fix mute/micmute LEDs for HP machines
  ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
  ALSA: hda - Add fixup for Dell Latitidue E5430
  ALSA: hda/conexant: Apply quirk for another HP ProDesk 600 G3 model
  ALSA: hda/realtek: Fix headset mic for Acer SF313-51
  ASoC: Intel: Skylake: Correct the handling of fmt_config flexible array
  ASoC: Intel: Skylake: Correct the ssp rate discovery in skl_get_ssp_clks()
  ASoC: rt5640: Fix the wrong state of JD1 and JD2
  ASoC: Intel: sof_rt5682: fix out-of-bounds array access
  ASoC: qdsp6: fix potential memory leak in q6apm_get_audioreach_graph()
  ASoC: tas2764: Fix amp gain register offset & default
  ASoC: tas2764: Correct playback volume range
  ASoC: tas2764: Fix and extend FSYNC polarity handling
  ASoC: tas2764: Add post reset delays
  ASoC: dt-bindings: Fix description for msm8916
  ASoC: doc: Capitalize RESET line name
  ASoC: arizona: Update arizona_aif_cfg_changed to use RX_BCLK_RATE
  ASoC: cs47l92: Fix event generation for OUT1 demux
  ...

nfp_tun_write_neigh() function will configure a tunnel neighbour when
calling nfp_tun_neigh_event_handler() or nfp_flower_cmsg_process_one_rx()
(with no tunnel neighbour type) from firmware.

When configuring IP on physical port as a tunnel endpoint, no operation
will be performed after receiving the cmsg mentioned above.

Therefore, add a progress to configure tunnel neighbour in this case.

v2: Correct format of fixes tag.

Fixes: f1df7956 ("nfp: flower: rework tunnel neighbour configuration")
Signed-off-by: Tianyu Yuan <tianyu.yuan@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220714081915.148378-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add missing error checks in tls_device_init.

Fixes: e8f69799 ("net/tls: Add generic NIC offload infrastructure")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220714070754.1428-1-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add Shyam Sundar S K as an additional maintainer to support the AMD XGBE
network device driver.

Cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/db367f24089c2bbbcd1cec8e21af49922017a110.1657751501.git.thomas.lendacky@amd.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

xenvif_rx_next_skb() is expecting the rx queue not being empty, but
in case the loop in xenvif_rx_action() is doing multiple iterations,
the availability of another skb in the rx queue is not being checked.

This can lead to crashes:

[40072.537261] BUG: unable to handle kernel NULL pointer dereference at 0000000000000080
[40072.537407] IP: xenvif_rx_skb+0x23/0x590 [xen_netback]
[40072.537534] PGD 0 P4D 0
[40072.537644] Oops: 0000 [#1] SMP NOPTI
[40072.537749] CPU: 0 PID: 12505 Comm: v1-c40247-q2-gu Not tainted 4.12.14-122.121-default #1 SLE12-SP5
[40072.537867] Hardware name: HP ProLiant DL580 Gen9/ProLiant DL580 Gen9, BIOS U17 11/23/2021
[40072.537999] task: ffff880433b38100 task.stack: ffffc90043d40000
[40072.538112] RIP: e030:xenvif_rx_skb+0x23/0x590 [xen_netback]
[40072.538217] RSP: e02b:ffffc90043d43de0 EFLAGS: 00010246
[40072.538319] RAX: 0000000000000000 RBX: ffffc90043cd7cd0 RCX: 00000000000000f7
[40072.538430] RDX: 0000000000000000 RSI: 0000000000000006 RDI: ffffc90043d43df8
[40072.538531] RBP: 000000000000003f R08: 000077ff80000000 R09: 0000000000000008
[40072.538644] R10: 0000000000007ff0 R11: 00000000000008f6 R12: ffffc90043ce2708
[40072.538745] R13: 0000000000000000 R14: ffffc90043d43ed0 R15: ffff88043ea748c0
[40072.538861] FS: 0000000000000000(0000) GS:ffff880484600000(0000) knlGS:0000000000000000
[40072.538988] CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033
[40072.539088] CR2: 0000000000000080 CR3: 0000000407ac8000 CR4: 0000000000040660
[40072.539211] Call Trace:
[40072.539319] xenvif_rx_action+0x71/0x90 [xen_netback]
[40072.539429] xenvif_kthread_guest_rx+0x14a/0x29c [xen_netback]

Fix that by stopping the loop in case the rx queue becomes empty.

Cc: stable@vger.kernel.org
Fixes: 98f6d57c ("xen-netback: process guest rx packets in batches")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220713135322.19616-1-jgross@suse.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The DRM_AMD_DC_DCN display engine support (Raven, Navi, and newer) has
not been building cleanly on powerpc and causes link errors due to
mixing hard- and soft-float object files:

  powerpc64-linux-ld: drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses hard float, drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o uses soft float
  powerpc64-linux-ld: failed to merge target specific data of file drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o
  [..]

and while patches are floating around, it's not exactly obvious what is
going on.

The problem bisects to commit 41b7a347 ("powerpc: Book3S 64-bit
outline-only KASAN support") but that is probably more about changing
config variables than the fundamental cause.

Despite the bisection result, a more directly related commit seems to be
26f4712a ("drm/amd/display: move FPU related code from dcn31 to
dml/dcn31 folder").  It's probably a combination of the two.

This has been going on since the merge window, without any final word.
So instead of blindly applying patches that may or may not be the right
thing, let's disable this for now.

As Michael Ellerman says:
 "IIUIC this code was never enabled on ppc before, so disabling it seems
  like a reasonable fix to get the build clean"

and once we have more actual feedback (and find any potential users) we
can always re-enable it with the patch that fixes the issues and
back-port as necessary.

Fixes: 41b7a347 ("powerpc: Book3S 64-bit outline-only KASAN support")
Fixes: 26f4712a ("drm/amd/display: move FPU related code from dcn31 to dml/dcn31 folder")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/all/20220606153910.GA1773067@roeck-us.net/
Link: https://lore.kernel.org/all/20220618232737.2036722-1-linux@roeck-us.net/
Link: https://lore.kernel.org/all/20220713050724.GA2471738@roeck-us.net/Acked-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This test implement the scenario described in the commit
"ip: fix dflt addr selection for connected nexthop".
The test configures a nexthop object with an output device only (no gateway
address) and a route that uses this nexthop. The goal is to check if the
kernel selects a valid source address.

Link: https://lore.kernel.org/netdev/20220712095545.10947-1-nicolas.dichtel@6wind.com/Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220713114853.29406-2-nicolas.dichtel@6wind.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When a nexthop is added, without a gw address, the default scope was set
to 'host'. Thus, when a source address is selected, 127.0.0.1 may be chosen
but rejected when the route is used.

When using a route without a nexthop id, the scope can be configured in the
route, thus the problem doesn't exist.

To explain more deeply: when a user creates a nexthop, it cannot specify
the scope. To create it, the function nh_create_ipv4() calls fib_check_nh()
with scope set to 0. fib_check_nh() calls fib_check_nh_nongw() wich was
setting scope to 'host'. Then, nh_create_ipv4() calls
fib_info_update_nhc_saddr() with scope set to 'host'. The src addr is
chosen before the route is inserted.

When a 'standard' route (ie without a reference to a nexthop) is added,
fib_create_info() calls fib_info_update_nhc_saddr() with the scope set by
the user. iproute2 set the scope to 'link' by default.

Here is a way to reproduce the problem:
ip netns add foo
ip -n foo link set lo up
ip netns add bar
ip -n bar link set lo up
sleep 1

ip -n foo link add name eth0 type dummy
ip -n foo link set eth0 up
ip -n foo address add 192.168.0.1/24 dev eth0

ip -n foo link add name veth0 type veth peer name veth1 netns bar
ip -n foo link set veth0 up
ip -n bar link set veth1 up

ip -n bar address add 192.168.1.1/32 dev veth1
ip -n bar route add default dev veth1

ip -n foo nexthop add id 1 dev veth0
ip -n foo route add 192.168.1.1 nhid 1

Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> RTNETLINK answers: Invalid argument
> $ ip netns exec foo ping -c1 192.168.1.1
> ping: connect: Invalid argument

Try without nexthop group (iproute2 sets scope to 'link' by dflt):
ip -n foo route del 192.168.1.1
ip -n foo route add 192.168.1.1 dev veth0

Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> 192.168.1.1 dev veth0 src 192.168.0.1 uid 0
>     cache
> $ ip netns exec foo ping -c1 192.168.1.1
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.039 ms
>
> --- 192.168.1.1 ping statistics ---
> 1 packets transmitted, 1 received, 0% packet loss, time 0ms
> rtt min/avg/max/mdev = 0.039/0.039/0.039/0.000 ms

CC: stable@vger.kernel.org
Fixes: 597cfe4f ("nexthop: Add support for IPv4 nexthops")
Reported-by: Edwin Brossette <edwin.brossette@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220713114853.29406-1-nicolas.dichtel@6wind.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

LKP reports a build issue on Clang, related to a literal load of
__current issued through the ldr_va macro. This turns out to be due to
the fact that group relocations are disabled when CONFIG_COMPILE_TEST=y,
which means that the ldr_va macro resolves to a pair of LDR
instructions, the first one being a literal load issued too far from its
literal pool.

Due to the introduction of a couple of new uses of this macro in commit
50807460 ("ARM: 9195/1: entry: avoid explicit literal loads"),
the literal pools end up getting rearranged in a way that causes the
literal for __current to go out of range. Let's fix this up by putting a
.ltorg directive in a suitable place in the code.

Link: https://lore.kernel.org/all/202205290805.1vZLAr36-lkp@intel.com/

Fixes: 50807460 ("ARM: 9195/1: entry: avoid explicit literal loads")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

"ARM: 9192/1: amba: fix memory leak in amba_device_try_add()" leads
to a refcount underflow if amba_device_add() fails, which called by
of_amba_device_create(), the of_amba_device_create() already exists
the error handling, so amba_put_device() only need to be added into
amba_deferred_retry().

Fixes: 7719a68b ("ARM: 9192/1: amba: fix memory leak in amba_device_try_add()")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

aq_nic_deinit() has been called while suspending, so we don't have to call
it again on resume.
Actually, call it again leads to another hang issue when resuming from
S3.

Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992345] Call Trace:
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992346] <TASK>
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992348] aq_nic_deinit+0xb4/0xd0 [atlantic]
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992356] aq_pm_thaw+0x7f/0x100 [atlantic]
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992362] pci_pm_resume+0x5c/0x90
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992366] ? pci_pm_thaw+0x80/0x80
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992368] dpm_run_callback+0x4e/0x120
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992371] device_resume+0xad/0x200
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992373] async_resume+0x1e/0x40
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992374] async_run_entry_fn+0x33/0x120
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992377] process_one_work+0x220/0x3c0
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992380] worker_thread+0x4d/0x3f0
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992382] ? process_one_work+0x3c0/0x3c0
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992384] kthread+0x12a/0x150
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992386] ? set_kthread_struct+0x40/0x40
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992387] ret_from_fork+0x22/0x30
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992391] </TASK>
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992392] ---[ end trace 1ec8c79604ed5e0d ]---
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992394] PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110
Jul 8 03:09:44 u-Precision-7865-Tower kernel: [ 5910.992397] atlantic 0000:02:00.0: PM: failed to resume async: error -110

Fixes: 1809c30b ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://lore.kernel.org/r/20220713111224.1535938-2-acelan.kao@canonical.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Below commit claims that atlantic NIC requires to reset the device on pm
op, and had set the deep to true for all suspend/resume functions.
commit 1809c30b ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
So, we could remove deep parameter on suspend/resume functions without
any functional change.

Fixes: 1809c30b ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://lore.kernel.org/r/20220713111224.1535938-1-acelan.kao@canonical.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When creating VFs a kernel panic can happen when calling to
efx_ef10_try_update_nic_stats_vf.

When releasing a DMA coherent buffer, sometimes, I don't know in what
specific circumstances, it has to unmap memory with vunmap. It is
disallowed to do that in IRQ context or with BH disabled. Otherwise, we
hit this line in vunmap, causing the crash:
  BUG_ON(in_interrupt());

This patch reenables BH to release the buffer.

Log messages when the bug is hit:
 kernel BUG at mm/vmalloc.c:2727!
 invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
 CPU: 6 PID: 1462 Comm: NetworkManager Kdump: loaded Tainted: G          I      --------- ---  5.14.0-119.el9.x86_64 #1
 Hardware name: Dell Inc. PowerEdge R740/06WXJT, BIOS 2.8.2 08/27/2020
 RIP: 0010:vunmap+0x2e/0x30
 ...skip...
 Call Trace:
  __iommu_dma_free+0x96/0x100
  efx_nic_free_buffer+0x2b/0x40 [sfc]
  efx_ef10_try_update_nic_stats_vf+0x14a/0x1c0 [sfc]
  efx_ef10_update_stats_vf+0x18/0x40 [sfc]
  efx_start_all+0x15e/0x1d0 [sfc]
  efx_net_open+0x5a/0xe0 [sfc]
  __dev_open+0xe7/0x1a0
  __dev_change_flags+0x1d7/0x240
  dev_change_flags+0x21/0x60
  ...skip...

Fixes: d7788196 ("sfc: DMA the VF stats only when requested")
Reported-by: Ma Yuying <yuma@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220713092116.21238-1-ihuguet@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Jan Beulich says:

====================
xen-netfront: XSA-403 follow-on

While investigating the XSA, I did notice a few more things. The two
patches aren't really dependent on one another.

1: remove leftover call to xennet_tx_buf_gc()
2: re-order error checks in xennet_get_responses()
====================

Link: https://lore.kernel.org/r/7fca0e44-43b5-8448-3653-249d117dc084@suse.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Check the retrieved grant reference first; there's no point trying to
have xennet_move_rx_slot() move invalid data (and further defer
recognition of the issue, likely making diagnosis yet more difficult).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

In talk_to_netback(), called earlier from xennet_connect(), queues and
shared rings were just re-initialized, so all this function call could
result in is setting ->broken (again) right away in case any unconsumed
responses were found.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Andrea Mayer says:

====================
seg6: fix skb checksum for SRH encapsulation/insertion

The Linux kernel supports Segment Routing Header (SRH)
encapsulation/insertion operations by providing the capability to: i)
encapsulate a packet in an outer IPv6 header with a specified SRH; ii)
insert a specified SRH directly after the IPv6 header of the packet.
Note that the insertion operation is also referred to as 'injection'.

The two operations are respectively supported by seg6_do_srh_encap() and
seg6_do_srh_inline(), which operate on the skb associated to the packet as
needed (e.g. adding the necessary headers and initializing them, while
taking care to recalculate the skb checksum).

seg6_do_srh_encap() and seg6_do_srh_inline() do not initialize the payload
length of the IPv6 header, which is carried out by the caller functions.
However, this approach causes the corruption of the skb checksum which
needs to be updated only after initialization of headers is completed
(thanks to Paolo Abeni for detecting this issue).

The patchset fixes the skb checksum corruption by moving the IPv6 header
payload length initialization from the callers of seg6_do_srh_encap() and
seg6_do_srh_inline() directly into these functions.

This patchset is organized as follows:
 - patch 1/3, seg6: fix skb checksum evaluation in SRH
   encapsulation/insertion;
    (* SRH encapsulation/insertion available since v4.10)

 - patch 2/3, seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps
   behaviors;
    (* SRv6 End.B6 and End.B6.Encaps behaviors available since v4.14)

 - patch 3/3, seg6: bpf: fix skb checksum in bpf_push_seg6_encap();
    (* bpf IPv6 Segment Routing helpers available since v4.18)

====================

Link: https://lore.kernel.org/r/20220712175837.16267-1-andrea.mayer@uniroma2.itSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Both helper functions bpf_lwt_seg6_action() and bpf_lwt_push_encap() use
the bpf_push_seg6_encap() to encapsulate the packet in an IPv6 with Segment
Routing Header (SRH) or insert an SRH between the IPv6 header and the
payload.
To achieve this result, such helper functions rely on bpf_push_seg6_encap()
which, in turn, leverages seg6_do_srh_{encap,inline}() to perform the
required operation (i.e. encap/inline).

This patch removes the initialization of the IPv6 header payload length
from bpf_push_seg6_encap(), as it is now handled properly by
seg6_do_srh_{encap,inline}() to prevent corruption of the skb checksum.

Fixes: fe94cc29 ("bpf: Add IPv6 Segment Routing helpers")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The SRv6 End.B6 and End.B6.Encaps behaviors rely on functions
seg6_do_srh_{encap,inline}() to, respectively: i) encapsulate the
packet within an outer IPv6 header with the specified Segment Routing
Header (SRH); ii) insert the specified SRH directly after the IPv6
header of the packet.

This patch removes the initialization of the IPv6 header payload length
from the input_action_end_b6{_encap}() functions, as it is now handled
properly by seg6_do_srh_{encap,inline}() to avoid corruption of the skb
checksum.

Fixes: 140f04c3 ("ipv6: sr: implement several seg6local actions")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Support for SRH encapsulation and insertion was introduced with
commit 6c8702c6 ("ipv6: sr: add support for SRH encapsulation and
injection with lwtunnels"), through the seg6_do_srh_encap() and
seg6_do_srh_inline() functions, respectively.
The former encapsulates the packet in an outer IPv6 header along with
the SRH, while the latter inserts the SRH between the IPv6 header and
the payload. Then, the headers are initialized/updated according to the
operating mode (i.e., encap/inline).
Finally, the skb checksum is calculated to reflect the changes applied
to the headers.

The IPv6 payload length ('payload_len') is not initialized
within seg6_do_srh_{inline,encap}() but is deferred in seg6_do_srh(), i.e.
the caller of seg6_do_srh_{inline,encap}().
However, this operation invalidates the skb checksum, since the
'payload_len' is updated only after the checksum is evaluated.

To solve this issue, the initialization of the IPv6 payload length is
moved from seg6_do_srh() directly into the seg6_do_srh_{inline,encap}()
functions and before the skb checksum update takes place.

Fixes: 6c8702c6 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/all/20220705190727.69d532417be7438b15404ee1@uniroma2.itSigned-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Set the maximum time firmware should poll for a link.
If not set firmware could block CPU for a long time resulting
in mailbox failures. If link doesn't come up within 1second,
firmware will anyway notify the status as and when LINK comes up
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha Sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20220712161815.12621-1-gakula@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-07-12

This series contains updates to ice driver only.

Paul fixes detection of E822 devices for firmware update and changes NVM
read for snapshot creation to be done in chunks as some systems cannot
read the entire NVM in the allotted time.
====================

Link: https://lore.kernel.org/r/20220712164829.7275-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use after free is detected by kfence when disabling sriov. What was read
after being freed was vf->pci_dev: it was freed from pci_disable_sriov
and later read in efx_ef10_sriov_free_vf_vports, called from
efx_ef10_sriov_free_vf_vswitching.

Set the pointer to NULL at release time to not trying to read it later.

Reproducer and dmesg log (note that kfence doesn't detect it every time):
$ echo 1 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs
$ echo 0 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs

 BUG: KFENCE: use-after-free read in efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]

 Use-after-free read at 0x00000000ff3c1ba5 (in kfence-#224):
  efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]
  efx_ef10_pci_sriov_disable+0x38/0x70 [sfc]
  efx_pci_sriov_configure+0x24/0x40 [sfc]
  sriov_numvfs_store+0xfe/0x140
  kernfs_fop_write_iter+0x11c/0x1b0
  new_sync_write+0x11f/0x1b0
  vfs_write+0x1eb/0x280
  ksys_write+0x5f/0xe0
  do_syscall_64+0x5c/0x80
  entry_SYSCALL_64_after_hwframe+0x44/0xae

 kfence-#224: 0x00000000edb8ef95-0x00000000671f5ce1, size=2792, cache=kmalloc-4k

 allocated by task 6771 on cpu 10 at 3137.860196s:
  pci_alloc_dev+0x21/0x60
  pci_iov_add_virtfn+0x2a2/0x320
  sriov_enable+0x212/0x3e0
  efx_ef10_sriov_configure+0x67/0x80 [sfc]
  efx_pci_sriov_configure+0x24/0x40 [sfc]
  sriov_numvfs_store+0xba/0x140
  kernfs_fop_write_iter+0x11c/0x1b0
  new_sync_write+0x11f/0x1b0
  vfs_write+0x1eb/0x280
  ksys_write+0x5f/0xe0
  do_syscall_64+0x5c/0x80
  entry_SYSCALL_64_after_hwframe+0x44/0xae

 freed by task 6771 on cpu 12 at 3170.991309s:
  device_release+0x34/0x90
  kobject_cleanup+0x3a/0x130
  pci_iov_remove_virtfn+0xd9/0x120
  sriov_disable+0x30/0xe0
  efx_ef10_pci_sriov_disable+0x57/0x70 [sfc]
  efx_pci_sriov_configure+0x24/0x40 [sfc]
  sriov_numvfs_store+0xfe/0x140
  kernfs_fop_write_iter+0x11c/0x1b0
  new_sync_write+0x11f/0x1b0
  vfs_write+0x1eb/0x280
  ksys_write+0x5f/0xe0
  do_syscall_64+0x5c/0x80
  entry_SYSCALL_64_after_hwframe+0x44/0xae

Fixes: 3c5eb876 ("sfc: create vports for VFs and assign random MAC addresses")
Reported-by: Yanghang Liu <yanghliu@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220712062642.6915-1-ihuguet@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>