- 29 Nov, 2012 1 commit
-
-
Emmanuel Grumbach authored
Don't return a hard coded -EFAULT, but rather the error that occurred in the flow. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
- 28 Nov, 2012 2 commits
-
-
Emmanuel Grumbach authored
Since the op_mode is leaving, the transport should set its pointer to it to NULL to not point to freed memory. Signed-off-by:
-
Emmanuel Grumbach authored
The FH (DMA engine) tells the driver the index of the last ready (closed) Rx buffer. This data is in closed_rb_num. If we read this data several times we may get inconsistencies between the code and the debug prints which can make it harder to debug issues here. Signed-off-by:
-
- 21 Nov, 2012 1 commit
-
-
Emmanuel Grumbach authored
Signed-off-by:
-
- 19 Nov, 2012 13 commits
-
-
Sachin Kamat authored
iwl-trans.h was included twice. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Emmanuel Grumbach authored
This will allow to reduce slightly the number of interrupts without sacrificing too much the latency in the Rx path. Signed-off-by:
-
Emmanuel Grumbach authored
It is not used outside pcie/rx.c. Signed-off-by:
-
Emmanuel Grumbach authored
Really trivial clean up. Signed-off-by:
-
Emmanuel Grumbach authored
Also, prefer the if(!X) notation over if(X == 0). Signed-off-by:
-
Johannes Berg authored
When software crypto is enabled, it isn't safe to enable MFP since the firmware interprets some management packets, and with MFP it would do so without proper validation. Reviewed-by:
Assaf Krauss <assaf.krauss@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
One one just a wrapper of the second, squash them. Signed-off-by:
-
Emmanuel Grumbach authored
Rename static functions. Function moved from trans.c to tx.c. A few could be made static, others had to be exported. Functions that implement the transport API are prefixed by iwl_trans_pcie_, the others by iwl_pcie_. Signed-off-by:
-
Emmanuel Grumbach authored
Functions that implement the transport API are prefixed by iwl_trans_pcie_, the others by iwl_pcie_. Signed-off-by:
-
Emmanuel Grumbach authored
Rename static functions. Function moved from trans.c to rx.c. A few could be made static, others had to be exported. Also, don't use rxb or rxbuf, but rb which stands for receive buffer. Signed-off-by:
-
Emmanuel Grumbach authored
This is its natural place Signed-off-by:
-
Emmanuel Grumbach authored
1) s/tx_queue/txq for the sake of consistency. 2) s/rx_queue/rxq for the sake of consistency. 3) Make all functions begin with iwl_pcie_ iwl_queue_init and iwl_queue_space are an exception since they are not PCIE specific although they are in pcie subdir. 4) s/trans_pcie_get_cmd_string/get_cmd_string it is much shorter and used in debug prints which are long lines. 5) s/iwl_bg_rx_replenish/iwl_pcie_rx_replenish_work this better emphasizes that it is a work 6) remove invalid kernelDOC markers pcie/tx.c and pcie/trans.c still needs to be cleaned up. Signed-off-by:
-
Emmanuel Grumbach authored
Signed-off-by:
-
- 14 Nov, 2012 2 commits
-
-
Emmanuel Grumbach authored
This is not needed, the comment there was wrong, it is only needed when MSI was *not* enabled. Signed-off-by:
-
Emmanuel Grumbach authored
The allocation failure will already be very verbose. Signed-off-by:
-
- 09 Nov, 2012 1 commit
-
-
Johannes Berg authored
When a firmware error occurs, don't just abort synchronous commands but also return an error (-EIO) and block any new commands as well. Currently, an error is only returned if WANT_SKB was set which is confusing and can lead to issues. Blocking is done until a new firmware image is loaded. Reviewed-by:
-
- 07 Nov, 2012 4 commits
-
-
Johannes Berg authored
The printk message should say RX, not TX. Reviewed-by:
-
Johannes Berg authored
There's no need to print the PCI resource length and base address, nor the hardware revision ID (which can be found in lspci) Reviewed-by:
-
Johannes Berg authored
There's no reason to print these all the time, the messages aren't all that interesting. Leave them as DEBUG_INFO though, just in case. Reviewed-by:
-
Johannes Berg authored
If the EEPROM reading was successful, don't print a message by default, the EEPROM version isn't all that interesting. Change the message to DEBUG_INFO priority so it can still be obtained. Reviewed-by:
-
- 05 Nov, 2012 6 commits
-
-
Emmanuel Grumbach authored
People tend not to set the fields they want to leave as 0. So make sure the struct is zeroed properly. Signed-off-by:
-
Emmanuel Grumbach authored
The ALIVE response of new fw inclues the base address of the SCD in SRAM. Until we read it from a prph register, which was set by the fw. Since the fw might well stop updating the prph register, add a WARN when there is an inconsitency between the ALIVE response and the register to catch any change in the behavior. Reviewed-by:
Gregory Greenman <gregory.greenman@intel.com> Reviewed-by:
-
Johannes Berg authored
Instead of open-coding it with a temporary list_head pointer, just use list_first_entry. Reviewed-by:
-
Johannes Berg authored
The flush_control parameter to iwlagn_txfifo_flush is passed as an internal value (context flags) and then sent to the device, that can't be right. Fix the confusion by removing the parameter, always use IWL_DROP_ALL that is redefined according to the firmware API in the flush control. Signed-off-by:
-
Johannes Berg authored
There's no reason to clear the CTL_AMPDU flag on transmitted frame status, it's not used by the driver here and mac80211 only uses it for some rate statistics. Also remove a stray space in the function. Reviewed-by:
-
Johannes Berg authored
The flush command really flushes queues, not FIFOs, and the first 32 bits indicate the queues to flush, not FIFOs. Change the command accordingly. Reviewed-by:
-
- 31 Oct, 2012 2 commits
-
-
Emmanuel Grumbach authored
When we unregister from mac80211 it will down the device anyway. Signed-off-by:
-
Emmanuel Grumbach authored
No HCMD can be sent while RFKILL is asserted. If a SYNC command is running while RFKILL is asserted the fw will silently discard it. This means that the driver needs to wake the process that sleeps on the CMD_SYNC. Since the RFKILL interrupt is handled in the transport layer and the code that sleeps in CMD_SYNC is also in the transport layer, all this logic can be handled there. This simplifies the work of the op_mode. So the transport layer will now return -ERFKILL when a CMD is sent and RFKILL is asserted. This will be the case even when the CMD is SYNC. The transport layer will return -ERFKILL straight away. Signed-off-by:
-
- 29 Oct, 2012 2 commits
-
-
Johannes Berg authored
Clarify the documentation to indicate that these flags can only be used at the end, i.e. after them a copy TFD (no flags set) is invalid. Reported-by:
Inbal Hacohen <inbal.hacohen@intel.com> Reviewed-by:
-
Johannes Berg authored
In addition to the NOCOPY flag, add a DUP flag that tells the transport to kmemdup() the buffer and free it after the command completes. Currently this is only supported for a single buffer in a given command, but that could be extended if it should be needed. Reviewed-by:
-
- 23 Oct, 2012 2 commits
-
-
Assaf Krauss authored
Remove the Kconfig option CONFIG_IWLWIFI_EXPERIMENTAL_MFP, if the firmware doesn't support MFP then the user shouldn't have the option to enable it as it won't work correctly. Signed-off-by:
-
Emmanuel Grumbach authored
Since the queue might not be empty, we need to free the pending Tx packets. Signed-off-by:
-
- 16 Oct, 2012 4 commits
-
-
Emmanuel Grumbach authored
This can happen when we shut down suddenly an interface. Signed-off-by:
-
Emmanuel Grumbach authored
Once in bus enumeration is enough, no need to print it again when the op_mode loads. Signed-off-by:
-
Emmanuel Grumbach authored
Doing the opposite is wrong, the SCD wouldn't like someone to clear its data while the queue is still active. Signed-off-by:
-
Emmanuel Grumbach authored
Instead of hardcoding the expression, use the macro provided in the previous patch. Signed-off-by:
-
