- 30 Aug, 2022 1 commit
-
-
Jani Nikula authored
Add a helper for getting the DP PHY name. In the interest of caller simplicity and to avoid allocations and passing in of buffers, duplicate the const strings to return. It's a minor penalty to pay for simplicity in all the call sites. v2: Rebase, add kernel-doc, ensure non-NULL always Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/b08dc12a7e621a48ec35546d6cd1ed4b1434810d.1660553850.git.jani.nikula@intel.com
-
- 29 Aug, 2022 7 commits
-
-
Hsin-Yi Wang authored
The double reset power-on sequence is a workaround for the hardware flaw in some chip that SPI Clock output glitch and cause internal MPU unable to read firmware correctly. The sequence is suggested in ps8640 application note. Signed-off-by:
Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by:
Rock Chiu <rock.chiu@paradetech.corp-partner.google.com> Signed-off-by:
Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220815093905.134164-1-hsinyi@chromium.org
-
Lucas Stach authored
There are two events that signal a real change of the link state: HPD going high means the sink is newly connected or wants the source to re-read the EDID, RX sense going low is a indication that the link has been disconnected. Ignore the other two events that also trigger interrupts, but don't need immediate attention: HPD going low does not necessarily mean the link has been lost and should not trigger a immediate read of the status. RX sense going high also does not require a detect cycle, as HPD going high is the right point in time to read the EDID. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> (v1) Reviewed-by:
Robert Foss <robert.foss@linaro.org> Signed-off-by:
-
Marek Vasut authored
The drm_of_lvds_get_data_mapping() returns either negative value on error or MEDIA_BUS_FMT_* otherwise. The check for 'ret' would also catch the positive case of MEDIA_BUS_FMT_* and lead to probe failure every time 'data-mapping' DT property is specified. Fixes: 7c4dd0a2 ("drm: of: Add drm_of_lvds_get_data_mapping") Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> To: dri-devel@lists.freedesktop.org Reviewed-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
Marek Vasut authored
Currently the driver only handles panel directly connected to the DPI output. Handle the case where a bridge is connected past DPI output of this bridge. This could be e.g. DPI to LVDS encoder chip. Signed-off-by:
-
Xin Ji authored
1. Support HDMI_I2S audio format. 2. Return 0 if there is no sink connection in .hw_param callback. Signed-off-by:
Xin Ji <xji@analogixsemi.com> Acked-by:
-
Jason Wang authored
The double `the' is duplicated in the comment, remove one. Signed-off-by:
Jason Wang <wangborong@cdjrlc.com> Signed-off-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220804114751.46714-1-wangborong@cdjrlc.com
-
Patrik Jakobsson authored
At some point the DRM printers started adding a newline after each print. This caused SDVO command debug printing to look weird. Fix this by using snprintf to print into a buffer which can be printed as a whole by DRM_DEBUG_KMS(). Code is heavily inspired by i915. Signed-off-by:
Daniel Vetter <daniel@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20220610130925.8650-1-patrik.r.jakobsson@gmail.com
-
- 26 Aug, 2022 6 commits
-
-
Linus Walleij authored
The "ret" variable is ambiguously returning something that could be zero in the tve200_modeset_init() function, assign it an explicit error return code to make this unambiguous. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
-
Marek Vasut authored
The ICN6211 is capable of deriving its internal PLL clock from either MIPI DSI HS clock, external REFCLK clock, or even internal oscillator. Currently supported is only the first option. Add support for external REFCLK clock input in addition to that. There is little difference between these options, except that in case of MIPI DSI HS clock input, the HS clock are pre-divided by a fixed /4 divider before being fed to the PLL input, while in case of external REFCLK, the RECLK clock are fed directly into the PLL input. Per exceptionally poor documentation, the REFCLK must be in range of 10..154 MHz. Signed-off-by:
-
Marek Vasut authored
The ICN6211 is capable of deriving its internal PLL clock from either MIPI DSI HS clock, external REFCLK clock, or even internal oscillator. Currently supported is only the first option. Document support for external REFCLK clock input in addition to that. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Marek Vasut authored
Fill in hs_rate and lp_rate to struct mipi_dsi_device for this bridge and adjust DSI input frequency calculations such that they expect the DSI host to configure HS clock according to hs_rate. This is an optimization for the DSI burst mode case. In case the DSI device supports DSI burst mode, it is recommended to operate the DSI interface at the highest possible HS clock frequency which the DSI device supports. This permits the DSI host to send as short as possible bursts of data on the DSI link and keep the DSI data lanes in LP mode otherwise, which reduces power consumption. Signed-off-by:
-
Randy Dunlap authored
drm_mipi_dbi needs lots of DRM_KMS_HELPER support, so select that Kconfig symbol like it is done is most other uses, and the way that it was before MIPS_DBI was moved from tinydrm to its core location. Fixes these build errors: ld: drivers/gpu/drm/drm_mipi_dbi.o: in function `mipi_dbi_buf_copy': drivers/gpu/drm/drm_mipi_dbi.c:205: undefined reference to `drm_gem_fb_get_obj' ld: drivers/gpu/drm/drm_mipi_dbi.c:211: undefined reference to `drm_gem_fb_begin_cpu_access' ld: drivers/gpu/drm/drm_mipi_dbi.c:215: undefined reference to `drm_gem_fb_vmap' ld: drivers/gpu/drm/drm_mipi_dbi.c:222: undefined reference to `drm_fb_swab' ld: drivers/gpu/drm/drm_mipi_dbi.c:224: undefined reference to `drm_fb_memcpy' ld: drivers/gpu/drm/drm_mipi_dbi.c:227: undefined reference to `drm_fb_xrgb8888_to_rgb565' ld: drivers/gpu/drm/drm_mipi_dbi.c:235: undefined reference to `drm_gem_fb_vunmap' ld: drivers/gpu/drm/drm_mipi_dbi.c:237: undefined reference to `drm_gem_fb_end_cpu_access' ld: drivers/gpu/drm/drm_mipi_dbi.o: in function `mipi_dbi_dev_init_with_formats': ld: drivers/gpu/drm/drm_mipi_dbi.o:/X64/../drivers/gpu/drm/drm_mipi_dbi.c:469: undefined reference to `drm_gem_fb_create_with_dirty' Fixes: 174102f4 ("drm/tinydrm: Move mipi-dbi") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Reported-by:
kernel test robot <lkp@intel.com> Cc: Dillon Min <dillon.minfei@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Noralf Trønnes <noralf@tronnes.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: dri-devel@lists.freedesktop.org Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
-
Randy Dunlap authored
Use 'select' instead of 'depends on' for DRM helpers for the Ilitek ILI9341 panel driver. This is what is done in the vast majority of other cases and this makes it possible to fix a build error with drm_mipi_dbi. Fixes: 5a042273 ("drm/panel: Add ilitek ili9341 panel driver") Signed-off-by:
-
- 25 Aug, 2022 6 commits
-
-
Rob Clark authored
When VIRTGPU_EXECBUF_RING_IDX is used, we should be considering the timeline that the EB if running on rather than the global driver fence context. Fixes: 85c83ea9 ("drm/virtio: implement context init: allocate an array of fence contexts") Signed-off-by:
Rob Clark <robdclark@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/20220812224001.2806463-1-robdclark@gmail.comSigned-off-by:
Gerd Hoffmann <kraxel@redhat.com>
-
Vivek Kasireddy authored
When userspace tries to map the dmabuf and if for some reason (e.g. OOM) the creation of the sg table fails, ubuf->sg needs to be set to NULL. Otherwise, when the userspace subsequently closes the dmabuf fd, we'd try to erroneously free the invalid sg table from release_udmabuf resulting in the following crash reported by syzbot: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] CPU: 0 PID: 3609 Comm: syz-executor487 Not tainted 5.19.0-syzkaller-13930-g7ebfc85e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/22/2022 RIP: 0010:dma_unmap_sgtable include/linux/dma-mapping.h:378 [inline] RIP: 0010:put_sg_table drivers/dma-buf/udmabuf.c:89 [inline] RIP: 0010:release_udmabuf+0xcb/0x4f0 drivers/dma-buf/udmabuf.c:114 Code: 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 2b 04 00 00 48 8d 7d 0c 4c 8b 63 30 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 e2 RSP: 0018:ffffc900037efd30 EFLAGS: 00010246 RAX: dffffc0000000000 RBX: ffffffff8cb67800 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff84ad27e0 RDI: 0000000000000000 RBP: fffffffffffffff4 R08: 0000000000000005 R09: 0000000000000000 R10: 0000000000000000 R11: 000000000008c07c R12: ffff88801fa05000 R13: ffff888073db07e8 R14: ffff888025c25440 R15: 0000000000000000 FS: 0000555555fc4300(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc1c0ce06e4 CR3: 00000000715e6000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> dma_buf_release+0x157/0x2d0 drivers/dma-buf/dma-buf.c:78 __dentry_kill+0x42b/0x640 fs/dcache.c:612 dentry_kill fs/dcache.c:733 [inline] dput+0x806/0xdb0 fs/dcache.c:913 __fput+0x39c/0x9d0 fs/file_table.c:333 task_work_run+0xdd/0x1a0 kernel/task_work.c:177 ptrace_notify+0x114/0x140 kernel/signal.c:2353 ptrace_report_syscall include/linux/ptrace.h:420 [inline] ptrace_report_syscall_exit include/linux/ptrace.h:482 [inline] syscall_exit_work kernel/entry/common.c:249 [inline] syscall_exit_to_user_mode_prepare+0x129/0x280 kernel/entry/common.c:276 __syscall_exit_to_user_mode_work kernel/entry/common.c:281 [inline] syscall_exit_to_user_mode+0x9/0x50 kernel/entry/common.c:294 do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7fc1c0c35b6b Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24 0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44 RSP: 002b:00007ffd78a06090 EFLAGS: 00000293 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 0000000000000007 RCX: 00007fc1c0c35b6b RDX: 0000000020000280 RSI: 0000000040086200 RDI: 0000000000000006 RBP: 0000000000000007 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000293 R12: 000000000000000c R13: 0000000000000003 R14: 00007fc1c0cfe4a0 R15: 00007ffd78a06140 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- RIP: 0010:dma_unmap_sgtable include/linux/dma-mapping.h:378 [inline] RIP: 0010:put_sg_table drivers/dma-buf/udmabuf.c:89 [inline] RIP: 0010:release_udmabuf+0xcb/0x4f0 drivers/dma-buf/udmabuf.c:114 Reported-by: syzbot+c80e9ef5d8bb45894db0@syzkaller.appspotmail.com Cc: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by:
Vivek Kasireddy <vivek.kasireddy@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20220825063522.801264-1-vivek.kasireddy@intel.comSigned-off-by:
-
Danilo Krummrich authored
In vc4_hvs_dump_state() potentially freed resources are protected from being accessed with drm_dev_enter()/drm_dev_exit(). Also include drm_print_regset32() in the protected section, since drm_print_regset32() does access memory that is typically mapped via devm_* calls. Fixes: 969cfae1 ("drm/vc4: hvs: Protect device resources after removal") Signed-off-by:
Danilo Krummrich <dakr@redhat.com> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220824161327.330627-5-dakr@redhat.com
-
Danilo Krummrich authored
(Hardware) resources which are bound to the driver and device lifecycle must not be accessed after the device and driver are unbound. However, the DRM device isn't freed as long as the last user closed it, hence userspace can still call into the driver. Therefore protect the critical sections which are accessing those resources with drm_dev_enter() and drm_dev_exit(). Fixes: 7cc4214c ("drm/vc4: crtc: Switch to drmm_kzalloc") Signed-off-by:
-
Danilo Krummrich authored
(Hardware) resources which are bound to the driver and device lifecycle must not be accessed after the device and driver are unbound. However, the DRM device isn't freed as long as the last user closed it, hence userspace can still call into the driver. Therefore protect the critical sections which are accessing those resources with drm_dev_enter() and drm_dev_exit(). Fixes: 9872c7a3 ("drm/vc4: plane: Switch to drmm_universal_plane_alloc()") Signed-off-by:
-
Danilo Krummrich authored
In vc4_hdmi_encoder_{pre,post}_crtc_enable() commit cd00ed51 ("drm/vc4: hdmi: Protect device resources after removal") missed to unlock the mutex before returning due to drm_dev_enter() indicating the device being unplugged. Fixes: cd00ed51 ("drm/vc4: hdmi: Protect device resources after removal") Signed-off-by:
-
- 23 Aug, 2022 20 commits
-
-
Lyude Paul authored
Now that we've finally gotten rid of the non-atomic MST users leftover in the kernel, we can finally get rid of all of the legacy payload code we have and move as much as possible into the MST atomic state structs. The main purpose of this is to make the MST code a lot less confusing to work on, as there's a lot of duplicated logic that doesn't really need to be here. As well, this should make introducing features like fallback link retraining and DSC support far easier. Since the old payload code was pretty gnarly and there's a Lot of changes here, I expect this might be a bit difficult to review. So to make things as easy as possible for reviewers, I'll sum up how both the old and new code worked here (it took me a while to figure this out too!). The old MST code basically worked by maintaining two different payload tables - proposed_vcpis, and payloads. proposed_vcpis would hold the modified payload we wanted to push to the topology, while payloads held the payload table that was currently programmed in hardware. Modifications to proposed_vcpis would be handled through drm_dp_allocate_vcpi(), drm_dp_mst_deallocate_vcpi(), and drm_dp_mst_reset_vcpi_slots(). Then, they would be pushed via drm_dp_mst_update_payload_step1() and drm_dp_mst_update_payload_step2(). Furthermore, it's important to note how adding and removing VC payloads actually worked with drm_dp_mst_update_payload_step1(). When a VC payload is removed from the VC table, all VC payloads which come after the removed VC payload's slots must have their time slots shifted towards the start of the table. The old code handles this by looping through the entire payload table and recomputing the start slot for every payload in the topology from scratch. While very much overkill, this ends up doing the right thing because we always order the VCPIs for payloads from first to last starting timeslot. It's important to also note that drm_dp_mst_update_payload_step2() isn't actually limited to updating a single payload - the driver can use it to queue up multiple payload changes so that as many of them can be sent as possible before waiting for the ACT. This is -technically- not against spec, but as Wayne Lin has pointed out it's not consistently implemented correctly in hubs - so it might as well be. drm_dp_mst_update_payload_step2() is pretty self explanatory and basically the same between the old and new code, save for the fact we don't have a second step for deleting payloads anymore -and thus rename it to drm_dp_mst_add_payload_step2(). The new payload code stores all of the current payload info within the MST atomic state and computes as much of the state as possible ahead of time. This has the one exception of the starting timeslots for payloads, which can't be determined at atomic check time since the starting time slots will vary depending on what order CRTCs are enabled in the atomic state - which varies from driver to driver. These are still stored in the atomic MST state, but are only copied from the old MST state during atomic commit time. Likewise, this is when new start slots are determined. Adding/removing payloads now works much more closely to how things are described in the spec. When we delete a payload, we loop through the current list of payloads and update the start slots for any payloads whose time slots came after the payload we just deleted. Determining the starting time slots for new payloads being added is done by simply keeping track of where the end of the VC table is in drm_dp_mst_topology_mgr->next_start_slot. Additionally, it's worth noting that we no longer have a single update_payload() function. Instead, we now have drm_dp_mst_add_payload_step1|2() and drm_dp_mst_remove_payload(). As such, it's now left it up to the driver to figure out when to add or remove payloads. The driver already knows when it's disabling/enabling CRTCs, so it also already knows when payloads should be added or removed. Changes since v1: * Refactor around all of the completely dead code changes that are happening in amdgpu for some reason when they really shouldn't even be there in the first place… :\ * Remove mention of sending one ACT per series of payload updates. As Wayne Lin pointed out, there are apparently hubs on the market that don't work correctly with this scheme and require a separate ACT per payload update. * Fix accidental drop of mst_mgr.lock - Wayne Lin * Remove mentions of allowing multiple ACT updates per payload change, mention that this is a result of vendors not consistently supporting this part of the spec and requiring a unique ACT for each payload change. * Get rid of reference to drm_dp_mst_port in DC - turns out I just got myself confused by DC and we don't actually need this. Changes since v2: * Get rid of fix for not sending payload deallocations if ddps=0 and just go back to wayne's fix Signed-off-by:
Lyude Paul <lyude@redhat.com> Cc: Wayne Lin <Wayne.Lin@amd.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Fangzhi Zuo <Jerry.Zuo@amd.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <sean@poorly.run> Acked-by:
-
Lyude Paul authored
Right now, radeon is technically the only non-atomic driver still making use of the MST helpers - and thus the final user of all of the legacy MST helpers. Originally I was going to look into seeing if we could move legacy MST into the radeon driver itself, however: * SI and CIK both can use amdgpu, which still supports MST * It currently doesn't work according to my own testing. I'm sure with some troubleshooting we could likely fix it, but that brings me to point #2: * It was never actually enabled by default, and is still marked as experimental in the module parameter description * If people were using it, someone probably would have probably seen a bug report about how it is currently not functional by now. That certainly doesn't appear to be the case, since before getting access to my own hardware I had to go out of my way to try finding someone to help test whether this legacy MST code even works - even amongst AMD employees. * Getting rid of this code and only having atomic versions of the MST helpers to maintain is likely going to be a lot easier in the long run, and will make it a lot easier for others contributing to this code to follow along with what's happening. FWIW - if anyone still wants this code to be in the tree and has a good idea of how to support this without needing to maintain the legacy MST helpers (trying to move them would probably be acceptable), I'm happy to suggestions. But my hope is that we can just drop this code and forget about it. I've already run this idea by Harry Wentland and Alex Deucher a few times as well. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Acked-by:
-
Lyude Paul authored
Currently, we set drm_dp_atomic_payload->time_slots to 0 in order to indicate that we're about to delete a payload in the current atomic state. Since we're going to be dropping all of the legacy code for handling the payload table however, we need to be able to ensure that we still keep track of the current time slot allocations for each payload so we can reuse this info when asking the root MST hub to delete payloads. We'll also be using it to recalculate the start slots of each VC. So, let's keep track of the intent of a payload in drm_dp_atomic_payload by adding ->delete, which we set whenever we're planning on deleting a payload during the current atomic commit. Signed-off-by:
-
Lyude Paul authored
We want to start cutting down on all of the places that we use port validation, so that ports may be removed from the topology as quickly as possible to minimize the number of errors we run into as a result of being out of sync with the current topology status. This isn't a very typical scenario and I don't think I've ever even run into it - but since the next commit is going to make some changes to payload updates depending on their hotplug status I think it's a probably good idea to take precautions. Let's do this with CSNs by moving some code around so that we only queue link address probing work at the end of handling all CSNs - allowing us to make sure we drop as many topology references as we can beforehand. Signed-off-by:
-
Lyude Paul authored
There's another kind of situation where we could potentially race with nonblocking modesets and MST, especially if we were to only use the locking provided by atomic modesetting: * Display 1 begins as enabled on DP-1 in SST mode * Display 1 switches to MST mode, exposes one sink in MST mode * Userspace does non-blocking modeset to disable the SST display * Userspace does non-blocking modeset to enable the MST display with a different CRTC, but the SST display hasn't been fully taken down yet * Execution order between the last two commits isn't guaranteed since they share no drm resources We can fix this however, by ensuring that we always pull in the atomic topology state whenever a connector capable of driving an MST display performs its atomic check - and then tracking CRTC commits happening on the SST connector in the MST topology state. So, let's add some simple helpers for doing that and hook them up in various drivers. v2: * Use intel_dp_mst_source_support() to check for MST support in i915, fixes CI failures Signed-off-by:
-
Lyude Paul authored
Since we're going to be relying on atomic locking for payloads now (and the MST mgr needs to track CRTCs), pull in the topology state for all modesets in nv50_msto_atomic_check(). Signed-off-by:
-
Lyude Paul authored
Post-NV50, the only kind of encoder you'll find for DP connectors on Nvidia GPUs are SORs (serial output resources). Because SORs have fixed associations with their connectors, we can correctly assume that any DP connector on a nvidia GPU will have exactly one SOR encoder routed to it for DisplayPort. Since we're going to need to be able to retrieve this fixed SOR DP encoder much more often as a result of hooking up MST helpers for tracking SST<->MST transitions in atomic states, let's simply cache this encoder in nouveau_connector for any DP connectors on the system to avoid looking it up each time. This isn't safe for NV50 since PIORs then come into play, however there's no code pre-NV50 that would need to look this up anyhow - so it's not really an issue. Signed-off-by:
-
Lyude Paul authored
Currently with the MST helpers we avoid releasing payloads _and_ avoid pulling in the MST state if there aren't any actual payload changes. While we want to keep the first step, we need to now make sure that we're always pulling in the MST state on all modesets that can modify payloads - even if the resulting payloads in the atomic state are identical to the previous ones. This is mainly to make it so that if a CRTC is still assigned to a connector but is set to DPMS off, the CRTC still holds it's payload allocation in the atomic state and still appropriately pulls in the MST state for commit tracking. Otherwise, we'll occasionally forget to update MST payloads from changes caused by non-atomic DPMS changes. Doing this also allows us to track bandwidth limitations in a state correctly even between DPMS changes, so that there's no chance of a simple ->active change being rejected by the atomic check. Signed-off-by:
-
Lyude Paul authored
I'm not sure why, but at the time I originally wrote the find/release time slot helpers I thought we should avoid keeping modeset tracking out of the MST helpers. In retrospect though there's no actual good reason to do this, and the logic has ended up being identical across all the drivers using the helpers. Also, it needs to be fixed anyway so we don't break things when going atomic-only with MST. So, let's just move this code into drm_dp_atomic_release_time_slots() and stop open coding it. Signed-off-by:
-
Lyude Paul authored
As Daniel Vetter pointed out, if we only use the atomic modesetting locks with MST it's technically possible for a driver with non-blocking modesets to race when it comes to MST displays - as we make the mistake of not doing our own CRTC commit tracking in the topology_state object. This could potentially cause problems if something like this happens: * User starts non-blocking commit to disable CRTC-1 on MST topology 1 * User starts non-blocking commit to enable CRTC-2 on MST topology 1 There's no guarantee here that the commit for disabling CRTC-2 will only occur after CRTC-1 has finished, since neither commit shares a CRTC - only the private modesetting object for MST. Keep in mind this likely isn't a problem for blocking modesets, only non-blocking. So, begin fixing this by keeping track of which CRTCs on a topology have changed by keeping track of which CRTCs we release or allocate timeslots on. As well, add some helpers for: * Setting up the drm_crtc_commit structs in the ->commit_setup hook * Waiting for any CRTC dependencies from the previous topology state v2: * Use drm_dp_mst_atomic_setup_commit() directly - Jani Signed-off-by:
-
Lyude Paul authored
We already open-code this quite often, and will be iterating through payloads even more once we've moved all of the payload tracking into the atomic state. So, let's add a helper for doing this. Signed-off-by:
-
Lyude Paul authored
Since we're about to start adding some stuff here, we may as well fill in any missing documentation that we forgot to write. Signed-off-by:
-
Lyude Paul authored
For some reason we mention returning 0 if "slots have been added back to drm_dp_mst_topology_state->avail_slots". This is totally misleading, avail_slots is simply for figuring out the total number of slots available in total on the topology and has no relation to the current payload allocations. So, let's get rid of that comment. Signed-off-by:
-
Lyude Paul authored
VCPI is only sort of the correct term here, originally the majority of this code simply referred to timeslots vaguely as "slots" - and since I started working on it and adding atomic functionality, the name "VCPI slots" has been used to represent time slots. Now that we actually have consistent access to the DisplayPort spec thanks to VESA, I now know this isn't actually the proper term - as the specification refers to these as time slots. Since we're trying to make this code as easy to figure out as possible, let's take this opportunity to correct this nomenclature and call them by their proper name - timeslots. Likewise, we rename various functions appropriately, along with replacing references in the kernel documentation and various debugging messages. It's important to note that this patch series leaves the legacy MST code untouched for the most part, which is fine since we'll be removing it soon anyhow. There should be no functional changes in this series. v2: * Add note that Wayne Lin from AMD suggested regarding slots being between the source DP Tx and the immediate downstream DP Rx Signed-off-by:
-
Lyude Paul authored
In retrospect, the name I chose for this originally is confusing, as there's a lot more info in here then just the VCPI. This really should be called a payload. Let's make it more obvious that this is meant to be related to the atomic state and is about payloads by renaming it to drm_dp_mst_atomic_payload. Also, rename various variables throughout the code that use atomic payloads. Signed-off-by:
-
Lyude Paul authored
This function isn't too confusing if you see the comment around the call-site for it, but if you don't then it's not at all obvious this is meant to copy DRM's payload table over to DC's internal state structs. Seeing this function before finding that comment definitely threw me into a loop a few times. So, let's rename this to make it's purpose more obvious regardless of where in the code you are. Signed-off-by:
-
Lyude Paul authored
Just to make this more clear to outside contributors that these are DC-specific structs, as this also threw me into a loop a number of times before I figured out the purpose of this. Signed-off-by:
-
Steev Klimaszewski authored
Add an eDP panel entry for IVO M133NW4J-R3. Due to lack of documentation, use the delay_200_500_p2e100 timings for now. Signed-off-by:
Steev Klimaszewski <steev@kali.org> [dianders: fixed typo in commit message] Reviewed-by:
-
wangjianli authored
Delete the redundant word 'at'. Signed-off-by:
wangjianli <wangjianli@cdjrlc.com> Reviewed-by:
Karol Herbst <kherbst@redhat.com> Signed-off-by:
-
Beniamin Sandu authored
This makes the code look cleaner and easier to read. Signed-off-by:
Beniamin Sandu <beniaminsandu@gmail.com> Reviewed-by:
-
