We now have *one* tty_port for both TTYs. How this was supposed to
work? Change it to have a tty_port for each of TTYs.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fail paths in ->probe and pti_init are incomplete. Fix that by adding
proper clean-up paths.

Note that we used to leak tty_driver on module unload. This is fixed
here too.

tty_unregister_driver needs not retval checking, so remove that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, probe initializes some parts. Then, some of them are
unwound in ->remove, some in module_exit. Let us do the opposite of
whole ->probe in ->remove.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function is lost somewhere in the forest. Move it to have it along
with probe and other pci_driver stuff.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Ioremap space is different to iomap. ->probe function uses ioremap,
but ->remove calls pci_iounmap. That one is illegal. Fix that by using
iounmap.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As we set drvdata unconditionally in ->probe, we need not check if it
is NULL. Let us remove the check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is annotated as __devinitconst. Despite the annotation is useless
in most cases, const keyword is misssing there. So we are placing
non-const data into rodata section. Fix that now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need to link a port to a tty in install. And since dlci is
allocated even in open, we need to create gsmtty_install, allocate
dlci there and create also the link.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty_struct->termios is no longer a pointer. This was changed recently
by "tty: move the termios object into the tty". But 68328serial was
not changed, so we now have a compilation error:
68328serial.c: In function 'change_speed':
68328serial.c:518:22: error: invalid type argument of '->' (have 'struct ktermios')
68328serial.c: In function 'rs_set_ldisc':
68328serial.c:620:31: error: invalid type argument of '->' (have 'struct ktermios')
68328serial.c: In function 'rs_set_termios':
68328serial.c:988:20: error: invalid type argument of '->' (have 'struct ktermios')

Fix that now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In case alloc_tty_struct fails in pty_common_install, we pass NULL to
free_tty_struct. This is invalid as the function is not ready to cope
with that. And even if it was, it is not nice to do that anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When PARMRK is set and large transfers of characters that will get
marked are being received, n_tty could drop data silently (i.e.
without reporting any error to the client). This is because
characters have the potential to take up to three bytes in the line
discipline (when they get marked with parity or framing errors), but
the amount of free space reported to tty_buffer flush_to_ldisc (via
tty->receive_room) is based on the pre-marked data size.

With this patch, the n_tty layer will no longer assume that each byte
will only take up one byte in the line discipline. Instead, it will
make an overly conservative estimate that each byte will take up
three bytes in the line discipline when PARMRK is set.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix possible panic caused by unlocked access to tty->read_cnt in
while-loop condition in n_tty_read().
Signed-off-by: Stanislav Kozina <skozina@redhat.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Also fix the silly speed setting bug.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The termios and other changes mean the other protections needed on the driver
tty arrays should be adequate. Turn it all back on.

This contains pieces folded in from the fixes made to the original patches

| From: Geert Uytterhoeven <geert@linux-m68k.org>	(fix m68k)
| From: Paul Gortmaker <paul.gortmaker@windriver.com>	(fix cris)
| From: Jiri Kosina <jkosina@suze.cz>			(lockdep)
| From: Eric Dumazet <eric.dumazet@gmail.com>		(lockdep)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We sometimes pass NULL pointers to free_tty_struct().  One example where
it can happen is in the error handling code in pty_common_install().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We're trying to save the termios state and we need to allocate a buffer
to do it.  Smatch complains that the buffer is leaked at the end of the
function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes the leak of a tty kref that Jiri pointed out.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the termios stuff but while we are at it do something about the rest of
it
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fixes these errors:

drivers/usb/serial/console.c: In function 'usb_console_setup':
drivers/usb/serial/console.c:168:16: error: invalid type argument of '->' (have 'struct ktermios')
drivers/usb/serial/console.c:169:4: error: incompatible type for argument 1 of 'tty_termios_encode_baud_rate'
include/linux/tty.h:449:13: note: expected 'struct ktermios *' but argument is of type 'struct ktermios'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This handles the merge issue in:
	arch/um/drivers/line.c
	arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull OLPC platform updates from Andres Salomon:
 "These move the OLPC Embedded Controller driver out of
  arch/x86/platform and into drivers/platform/olpc.

  OLPC machines are now ARM-based (which means lots of x86 and ARM
  changes), but are typically pretty self-contained..  so it makes more
  sense to go through a separate OLPC tree after getting the appropriate
  review/ACKs."

* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
  x86: OLPC: move s/r-related EC cmds to EC driver
  Platform: OLPC: move global variables into priv struct
  Platform: OLPC: move debugfs support from x86 EC driver
  x86: OLPC: switch over to using new EC driver on x86
  Platform: OLPC: add a suspended flag to the EC driver
  Platform: OLPC: turn EC driver into a platform_driver
  Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
  drivers: OLPC: update various drivers to include olpc-ec.h
  Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver

Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
 "This contains a set of device-tree conversions for Marvell Orion
  platforms that were staged early but took a few tries to get the
  branch into a format where it was suitable for us to pick up.

  Given that most people working on these platforms are hobbyists with
  limited time, we were a bit more flexible with merging it even though
  it came in late."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: Kirkwood: Replace mrvl with marvell
  ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
  ARM: Kirkwood: Describe Dreamplug LEDs in DT.
  ARM: Kirkwood: Describe iConnects LEDs in DT.
  ARM: Kirkwood: Describe iConnects temperature sensor in DT.
  ARM: Kirkwood: Describe IB62x0 LEDs in DT.
  ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
  ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
  ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
  ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
  ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
  ARM: Kirkwood: Use DT to configure SATA device.
  ARM: kirkwood: use devicetree for SPI on dreamplug
  ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
  ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
  ARM: Kirkwood: Add basic device tree support for QNAP TS219.
  ATA: sata_mv: Add device tree support
  ARM: Orion: DTify the watchdog timer.
  ARM: Orion: Add arch support needed for I2C via DT.
  ARM: kirkwood: use devicetree for orion-spi
  ...

Conflicts:
	drivers/watchdog/orion_wdt.c

Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
 "Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
  but didn't go in because the pull request ended up rejected.  So it
  just got merged, and we got this staged branch that enables the
  coupled cpuidle code on OMAP.

  With a stable git workflow from the other maintainer we could have
  staged this earlier, but that wasn't the case so we have had to merge
  it late.

  The alternative is to hold it off until 3.7 but given that the code is
  well-isolated to OMAP and they are eager to see it go in, I didn't
  push back hard in that direction."

* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP4: CPUidle: Open broadcast clock-event device.
  ARM: OMAP4: CPUidle: add synchronization for coupled idle states
  ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
  ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes for merge window fallout, and a bugfix for timer resume on
  PRIMA2."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: mmp: add missing irqs.h
  arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
  ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
  ARM: mxc: Include missing irqs.h header

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...

Pull additional md update from NeilBrown:
 "This contains a few patches that depend on plugging changes in the
  block layer so needed to wait for those.

  It also contains a Kconfig fix for the new RAID10 support in dm-raid."

* tag 'md-3.6' of git://neil.brown.name/md:
  md/dm-raid: DM_RAID should select MD_RAID10
  md/raid1: submit IO from originating thread instead of md thread.
  raid5: raid5d handle stripe in batch way
  raid5: make_request use batch stripe release

Pull two ceph fixes from Sage Weil:
 "The first patch fixes up the old crufty open intent code to use the
  atomic_open stuff properly, and the second fixes a possible null deref
  and memory leak with the crypto keys."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: fix crypto key null deref, memory leak
  ceph: simplify+fix atomic_open

Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes a bug when the lower filesystem mount options include 'acl',
   but the eCryptfs mount options do not
 - Cleanups in the messaging code
 - Better handling of empty files in the lower filesystem to improve
   usability.  Failed file creations are now cleaned up and empty lower
   files are converted into eCryptfs during open().
 - The write-through cache changes are being reverted due to bugs that
   are not easy to fix.  Stability outweighs the performance
   enhancements here.
 - Improvement to the mount code to catch unsupported ciphers specified
   in the mount options

* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: check for eCryptfs cipher support at mount
  eCryptfs: Revert to a writethrough cache model
  eCryptfs: Initialize empty lower files when opening them
  eCryptfs: Unlink lower inode when ecryptfs_create() fails
  eCryptfs: Make all miscdev functions use daemon ptr in file private_data
  eCryptfs: Remove unused messaging declarations and function
  eCryptfs: Copy up POSIX ACL and read-only flags from lower mount

Pull CIFS update from Steve French:
 "Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.

  I am holding up a few more days on merging the remainder of the
  SMB2/SMB2.1 enablement although it is nearing review completion, in
  order to address some review comments from Jeff Layton on a few of the
  subsequent SMB2 patches, and also to debug an unrelated cifs problem
  that Pavel discovered."

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Add SMB2 support for rmdir
  CIFS: Move rmdir code to ops struct
  CIFS: Add SMB2 support for mkdir operation
  CIFS: Separate protocol specific part from mkdir
  CIFS: Simplify cifs_mkdir call

Borislav Petkov reports that the new warning added in commit
88fdf75d ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.

The call trace looks like this:

  x86_64_start_kernel ->
    x86_64_start_reservations ->
    start_kernel ->
    setup_arch ->
    paging_init ->
    zone_sizes_init ->
    free_area_init_nodes ->
    free_area_init_node

and (with the warning replaced by debug output), Borislav sees

  On node 0 totalpages: 4193848
    DMA zone: 64 pages used for memmap
    DMA zone: 6 pages reserved
    DMA zone: 3890 pages, LIFO batch:0
    DMA32 zone: 16320 pages used for memmap
    DMA32 zone: 798464 pages, LIFO batch:31
    Normal zone: 52736 pages used for memmap
    Normal zone: 3322368 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 4423680      <----
  On node 1 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 8617984      <----
  On node 2 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 12812288     <----
  On node 3 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31

so remove the bogus warning for now to avoid annoying people.  Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1

Include <mach/irqs.h> to fix this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
	SIRFSOC_TIMER_LATCH);

Writing values to LATCHED registers directly is useless at all.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Avoid crashing if the crypto key payload was NULL, as when it was not correctly
allocated and initialized.  Also, avoid leaking it.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>

The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work.  Replace it with a fresh
method.  In particular:

 * always attempt to do an atomic open+lookup, both for the create case
   and for lookups of existing files.
 * fix symlink handling by returning 1 to the VFS so that we can follow
   the link to its destination. This fixes a longstanding ceph bug (#2392).
Signed-off-by: Sage Weil <sage@inktank.com>

setup-sh7722.c defines several objects, whose types are defined in
sh_dma.h, so, it has to be included explicitly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Pull MIPS updates from Ralf Baechle:
 "The lion share of this pull request are fixes for clk-related breakage
  caused by other changes during this merge window.  For some platforms
  the fix was as simple as selecting HAVE_CLK, for others like the
  Loongson 2 significant restructuring was required.

  The remainder are changes required to get the Lantiq code to work
  again."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Loongson 2: Sort out clock managment.
  MIPS: Loongson 1: more clk support and add select HAVE_CLK
  MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: Lantiq: Platform specific CLK fixup
  MIPS: Lantiq: Add device_tree_init function
  MIPS: Lantiq: Fix interface clock and PCI control register offset

Pull UML fixes from Richard Weinberger:
 "This patch set contains mostly fixes and cleanups.  The UML tty driver
  uses now tty_port and is no longer broken like hell  :-)"

* 'for-linus-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Add arch/x86/um to MAINTAINERS
  um: pass siginfo to guest process
  um: fix ubd_file_size for read-only files
  um: pull interrupt_end() into userspace()
  um: split syscall_trace(), pass pt_regs to it
  um: switch UPT_SET_RETURN_VALUE and regs_return_value to pt_regs
  um: set BLK_CGROUP=y in defconfig
  um: remove count_lock
  um: fully use tty_port
  um: Remove dead code
  um: remove line_ioctl()
  TTY: um/line, use tty from tty_port
  TTY: um/line, add tty_port

Pull ARM DMA engine updates from Russell King:
 "This looks scary at first glance, but what it is is:
   - a rework of the sa11x0 DMA engine driver merged during the previous
     cycle, to extract a common set of helper functions for DMA engine
     implementations.
   - conversion of amba-pl08x.c to use these helper functions.
   - addition of OMAP DMA engine driver (using these helper functions),
     and conversion of some of the OMAP DMA users to use DMA engine.

  Nothing in the helper functions is ARM specific, so I hope that other
  implementations can consolidate some of their code by making use of
  these helpers.

  This has been sitting in linux-next most of the merge cycle, and has
  been tested by several OMAP folk.  I've tested it on sa11x0 platforms,
  and given it my best shot on my broken platforms which have the
  amba-pl08x controller.

  The last point is the addition to feature-removal-schedule.txt, which
  will have a merge conflict.  Between myself and TI, we're planning to
  remove the old TI DMA implementation next year."

Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}

* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
  ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
  ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
  Add feature removal of old OMAP private DMA implementation
  mtd: omap2: remove private DMA API implementation
  mtd: omap2: add DMA engine support
  spi: omap2-mcspi: remove private DMA API implementation
  spi: omap2-mcspi: add DMA engine support
  ARM: omap: remove mmc platform data dma_mask and initialization
  mmc: omap: remove private DMA API implementation
  mmc: omap: add DMA engine support
  mmc: omap_hsmmc: remove private DMA API implementation
  mmc: omap_hsmmc: add DMA engine support
  dmaengine: omap: add support for cyclic DMA
  dmaengine: omap: add support for setting fi
  dmaengine: omap: add support for returning residue in tx_state method
  dmaengine: add OMAP DMA engine driver
  dmaengine: sa11x0-dma: add cyclic DMA support
  dmaengine: sa11x0-dma: fix DMA residue support
  dmaengine: PL08x: ensure all descriptors are freed when channel is released
  dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
  ...