- 22 Oct, 2021 20 commits
-
-
Christophe Leroy authored
Add support for out-of-line static calls on PPC32. This change improve performance of calls to global function pointers by using direct calls instead of indirect calls. The trampoline is initialy populated with a 'blr' or branch to target, followed by an unreachable long jump sequence. In order to cater with parallele execution, the trampoline needs to be updated in a way that ensures it remains consistent at all time. This means we can't use the traditional lis/addi to load r12 with the target address, otherwise there would be a window during which the first instruction contains the upper part of the new target address while the second instruction still contains the lower part of the old target address. To avoid that the target address is stored just after the 'bctr' and loaded from there with a single instruction. Then, depending on the target distance, arch_static_call_transform() will either replace the first instruction by a direct 'bl <target>' or 'nop' in order to have the trampoline fall through the long jump sequence. For the special case of __static_call_return0(), to avoid the risk of a far branch, a version of it is inlined at the end of the trampoline. Performancewise the long jump sequence is probably not better than the indirect calls set by GCC when we don't use static calls, but such calls are unlikely to be required on powerpc32: With most configurations the kernel size is far below 32 Mbytes so only modules may happen to be too far. And even modules are likely to be close enough as they are allocated below the kernel core and as close as possible of the kernel text. static_call selftest is running successfully with this change. With this patch, __do_irq() has the following sequence to trace irq entries: c0004a00 <__SCT__tp_func_irq_entry>: c0004a00: 48 00 00 e0 b c0004ae0 <__traceiter_irq_entry> c0004a04: 3d 80 c0 00 lis r12,-16384 c0004a08: 81 8c 4a 1c lwz r12,18972(r12) c0004a0c: 7d 89 03 a6 mtctr r12 c0004a10: 4e 80 04 20 bctr c0004a14: 38 60 00 00 li r3,0 c0004a18: 4e 80 00 20 blr c0004a1c: 00 00 00 00 .long 0x0 ... c0005654 <__do_irq>: ... c0005664: 7c 7f 1b 78 mr r31,r3 ... c00056a0: 81 22 00 00 lwz r9,0(r2) c00056a4: 39 29 00 01 addi r9,r9,1 c00056a8: 91 22 00 00 stw r9,0(r2) c00056ac: 3d 20 c0 af lis r9,-16209 c00056b0: 81 29 74 cc lwz r9,29900(r9) c00056b4: 2c 09 00 00 cmpwi r9,0 c00056b8: 41 82 00 10 beq c00056c8 <__do_irq+0x74> c00056bc: 80 69 00 04 lwz r3,4(r9) c00056c0: 7f e4 fb 78 mr r4,r31 c00056c4: 4b ff f3 3d bl c0004a00 <__SCT__tp_func_irq_entry> Before this patch, __do_irq() was doing the following to trace irq entries: c0005700 <__do_irq>: ... c0005710: 7c 7e 1b 78 mr r30,r3 ... c000574c: 93 e1 00 0c stw r31,12(r1) c0005750: 81 22 00 00 lwz r9,0(r2) c0005754: 39 29 00 01 addi r9,r9,1 c0005758: 91 22 00 00 stw r9,0(r2) c000575c: 3d 20 c0 af lis r9,-16209 c0005760: 83 e9 f4 cc lwz r31,-2868(r9) c0005764: 2c 1f 00 00 cmpwi r31,0 c0005768: 41 82 00 24 beq c000578c <__do_irq+0x8c> c000576c: 81 3f 00 00 lwz r9,0(r31) c0005770: 80 7f 00 04 lwz r3,4(r31) c0005774: 7d 29 03 a6 mtctr r9 c0005778: 7f c4 f3 78 mr r4,r30 c000577c: 4e 80 04 21 bctrl c0005780: 85 3f 00 0c lwzu r9,12(r31) c0005784: 2c 09 00 00 cmpwi r9,0 c0005788: 40 82 ff e4 bne c000576c <__do_irq+0x6c> Behind the fact of now using a direct 'bl' instead of a 'load/mtctr/bctr' sequence, we can also see that we get one less register on the stack. Signed-off-by:
Christophe Leroy <christophe.leroy@csgroup.eu> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/6ec2a7865ed6a5ec54ab46d026785bafe1d837ea.1630484892.git.christophe.leroy@csgroup.eu
-
Christophe Leroy authored
ppc_md.iommu_save() is not set anymore by any platform after commit c40785ad ("powerpc/dart: Use a cachable DART"). So iommu_save() has become a nop and can be removed. ppc_md.show_percpuinfo() is not set anymore by any platform after commit 4350147a ("[PATCH] ppc64: SMU based macs cpufreq support"). Last users of ppc_md.rtc_read_val() and ppc_md.rtc_write_val() were removed by commit 0f03a43b ("[POWERPC] Remove todc code from ARCH=powerpc") Last user of kgdb_map_scc() was removed by commit 17ce452f ("kgdb, powerpc: arch specific powerpc kgdb support"). ppc.machine_kexec_prepare() has not been used since commit 8ee3e0d6 ("powerpc: Remove the main legacy iSerie platform code"). This allows the removal of machine_kexec_prepare() and the rename of default_machine_kexec_prepare() into machine_kexec_prepare() Signed-off-by:
Daniel Axtens <dja@axtens.net> [mpe: Drop prototype for default_machine_kexec_prepare() as noted by dja] Signed-off-by:
-
Christophe Leroy authored
Commit d75d68cf ("powerpc: Clean up obsolete code relating to decrementer and timebase") made generic_suspend_enable_irqs() and generic_suspend_disable_irqs() static. Fold them into their only caller. Signed-off-by:
-
Christophe Leroy authored
Commit e65e1fc2 ("[PATCH] syscall class hookup for all normal targets") added generic support for AUDIT but that didn't include support for bi-arch like powerpc. Commit 4b588411 ("audit: Add generic compat syscall support") added generic support for bi-arch. Convert powerpc to that bi-arch generic audit support. Signed-off-by:
-
Christophe Leroy authored
Instructions lmw/stmw are interesting for functions that are rarely used and not in the cache, because only one instruction is to be copied into the instruction cache instead of 19. However those instruction are less performant than 19x raw lwz/stw as they require synchronisation plus one additional cycle. SAVE_NVGPRS / REST_NVGPRS are used in only a few places which are mostly in interrupts entries/exits and in task switch so they are likely already in the cache. Using standard lwz improves null_syscall selftest by: - 10 cycles on mpc832x. - 2 cycles on mpc8xx. Signed-off-by:
-
Anatolij Gustschin authored
Fixes build warnings: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name Signed-off-by:
Anatolij Gustschin <agust@denx.de> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Anatolij Gustschin authored
Fix ranges property warnings: pci@f0000d00:ranges: 'oneOf' conditional failed, one must be fixed: Signed-off-by:
-
Anatolij Gustschin authored
Add ranges property to fix build warnings: Warning (pci_bridge): /pci@f0000d00: missing ranges for PCI bridge (or not a bridge) Signed-off-by:
-
Gustavo A. R. Silva authored
(!ptr && !ptr->foo) strikes again. :) The expression (!ptr && !ptr->foo) is bogus and in case ptr is NULL, it leads to a NULL pointer dereference: ptr->foo. Fix this by converting && to || This issue was detected with the help of Coccinelle, and audited and fixed manually. Fixes: 1a0d0d5e ("powerpc/vas: Add platform specific user window operations") Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by:
Tyrel Datwyler <tyreld@linux.ibm.com> Signed-off-by:
-
Christophe Leroy authored
Enable STRICT_KERNEL_RWX on fsl_booke. For that, we need additional TLBCAMs dedicated to linear mapping, based on the alignment of _sinittext. By default, up to 768 Mbytes of memory are mapped. It uses 3 TLBCAMs of size 256 Mbytes. With a data alignment of 16, we need up to 9 TLBCAMs: 16/16/16/16/64/64/64/256/256 With a data alignment of 4, we need up to 12 TLBCAMs: 4/4/4/4/16/16/16/64/64/64/256/256 With a data alignment of 1, we need up to 15 TLBCAMs: 1/1/1/1/4/4/4/16/16/16/64/64/64/256/256 By default, set a 16 Mbytes alignment as a compromise between memory usage and number of TLBCAMs. This can be adjusted manually when needed. For the time being, it doens't work when the base is randomised. Signed-off-by:
-
Christophe Leroy authored
After init, set readonly memory as ROX and set readwrite memory as RWX, if STRICT_KERNEL_RWX is enabled. Signed-off-by:
-
Christophe Leroy authored
Reorganise TLBCAM allocation so that when STRICT_KERNEL_RWX is enabled, TLBCAMs are allocated such that readonly memory uses different TLBCAMs. This results in an allocation looking like: Memory CAM mapping: 4/4/4/1/1/1/1/16/16/16/64/64/64/256/256 Mb, residual: 256Mb Signed-off-by:
-
Christophe Leroy authored
In order to be able to call map_mem_in_cams() once more after init for STRICT_KERNEL_RWX, add an argument. For now, map_mem_in_cams() is always called only during init. Signed-off-by:
-
Christophe Leroy authored
Avoid switching to AS1 when reloading TLBCAM after init for STRICT_KERNEL_RWX. When we setup AS1 we expect the entire accessible memory to be mapped through one entry, this is not the case anymore at the end of init. We are not changing the size of TLBCAMs, only flags, so no need to switch to AS1. So change loadcam_multi() to not switch to AS1 when the given temporary tlb entry in 0. Signed-off-by:
-
Christophe Leroy authored
Don't force MAS3_SX and MAS3_UX at all time. Take into account the exec flag. While at it, fix a couple of closeby style problems (indent with space and unnecessary parenthesis), it keeps more readability. Signed-off-by:
-
Christophe Leroy authored
We have a myriad of CONFIG symbols around different variants of BOOKEs, which would be worth tidying up one day. But at least, make file names and CONFIG option match: We have CONFIG_FSL_BOOKE and CONFIG_PPC_FSL_BOOK3E. fsl_booke.c is selected by and only by CONFIG_PPC_FSL_BOOK3E. So rename it fsl_book3e to reduce confusion. Signed-off-by:
-
Christophe Leroy authored
fsl_booke and 44x are not able to map kernel linear memory with pages, so they can't support DEBUG_PAGEALLOC and KFENCE, and STRICT_KERNEL_RWX is also a problem for now. Enable those only on book3s (both 32 and 64 except KFENCE), 8xx and 40x. Fixes: 88df6e90 ("[POWERPC] DEBUG_PAGEALLOC for 32-bit") Fixes: 95902e6c ("powerpc/mm: Implement STRICT_KERNEL_RWX on PPC32") Fixes: 90cbac0e ("powerpc: Enable KFENCE for PPC32") Signed-off-by:
-
Wan Jiabing authored
Fix following coccicheck warning: ./arch/powerpc/kexec/file_load_64.c:698:1-22: WARNING: Function for_each_node_by_type should have of_node_put() before goto Early exits from for_each_node_by_type should decrement the node reference counter. Signed-off-by:
Wan Jiabing <wanjiabing@vivo.com> Acked-by:
Hari Bathini <hbathini@linux.ibm.com> Signed-off-by:
-
Wan Jiabing authored
Fix following coccicheck warning: ./arch/powerpc/platforms/pseries/iommu.c:924:1-28: WARNING: Function for_each_node_with_property should have of_node_put() before break Early exits from for_each_node_with_property should decrement the node reference counter. Signed-off-by:
Leonardo Bras <leobras.c@gmail.com> Signed-off-by:
-
Joel Stanley authored
The page_alloc.c code will call into __kernel_map_pages() when DEBUG_PAGEALLOC is configured and enabled. As the implementation assumes hash, this should crash spectacularly if not for a bit of luck in __kernel_map_pages(). In this function linear_map_hash_count is always zero, the for loop exits without doing any damage. There are no other platforms that determine if they support debug_pagealloc at runtime. Instead of adding code to mm/page_alloc.c to do that, this change turns the map/unmap into a noop when in radix mode and prints a warning once. Signed-off-by:
Joel Stanley <joel@jms.id.au> Reviewed-by:
-
- 14 Oct, 2021 2 commits
-
-
Christophe Leroy authored
.opd section contains function descriptors used to locate functions in the kernel. If someone is able to modify a function descriptor he will be able to run arbitrary kernel function instead of another. To avoid that, move .opd section inside read-only memory. Signed-off-by:
-
Athira Rajeev authored
On power9 and earlier platforms, the default event used for cyles and instructions is PM_CYC (0x0001e) and PM_INST_CMPL (0x00002) respectively. These events use two programmable PMCs and by default will count irrespective of the run latch state (idle state). But since they use programmable PMCs, these events can lead to multiplexing with other events, because there are only 4 programmable PMCs. Hence in power10, performance monitoring unit (PMU) driver uses performance monitor counter 5 (PMC5) and performance monitor counter6 (PMC6) for counting instructions and cycles. Currently on power10, the event used for cycles is PM_RUN_CYC (0x600F4) and instructions uses PM_RUN_INST_CMPL (0x500fa). But counting of these events in idle state is controlled by the CC56RUN bit setting in Monitor Mode Control Register0 (MMCR0). If the CC56RUN bit is zero, PMC5/6 will not count when CTRL[RUN] (run latch) is zero. This could lead to missing some counts if a thread is in idle state during system wide profiling. To fix it, set the CC56RUN bit in MMCR0 for power10, which makes PMC5 and PMC6 count instructions and cycles regardless of the run latch state. Since this change make PMC5/6 count as PM_INST_CMPL/PM_CYC, rename the event code 0x600f4 as PM_CYC instead of PM_RUN_CYC and event code 0x500fa as PM_INST_CMPL instead of PM_RUN_INST_CMPL. The changes are only for PMC5/6 event codes and will not affect the behaviour of PM_RUN_CYC/PM_RUN_INST_CMPL if progammed in other PMC's. Fixes: a64e697c ("powerpc/perf: power10 Performance Monitoring support") Signed-off-by:
Athira Rajeev <atrajeev@linux.vnet.ibm.cm> Reviewed-by:
Madhavan Srinivasan <maddy@linux.ibm.com> [mpe: Tweak change log wording for style and consistency] Signed-off-by:
-
- 13 Oct, 2021 3 commits
-
-
Kai Song authored
We fix the following warnings when building kernel with W=1: arch/powerpc/kernel/eeh.c:598: warning: Function parameter or member 'function' not described in 'eeh_pci_enable' arch/powerpc/kernel/eeh.c:774: warning: Function parameter or member 'edev' not described in 'eeh_set_dev_freset' arch/powerpc/kernel/eeh.c:774: warning: expecting prototype for eeh_set_pe_freset(). Prototype was for eeh_set_dev_freset() instead arch/powerpc/kernel/eeh.c:814: warning: Function parameter or member 'include_passed' not described in 'eeh_pe_reset_full' arch/powerpc/kernel/eeh.c:944: warning: Function parameter or member 'ops' not described in 'eeh_init' arch/powerpc/kernel/eeh.c:1451: warning: Function parameter or member 'include_passed' not described in 'eeh_pe_reset' arch/powerpc/kernel/eeh.c:1526: warning: Function parameter or member 'func' not described in 'eeh_pe_inject_err' arch/powerpc/kernel/eeh.c:1526: warning: Excess function parameter 'function' described in 'eeh_pe_inject_err' Signed-off-by:
Kai Song <songkai01@inspur.com> Reviewed-by:
-
Cédric Le Goater authored
CONFIG_PPC64_BOOT_WRAPPER is selected by CPU_LITTLE_ENDIAN which is used to compile support for other platforms such as Microwatt. There is no need for OPAL calls on these. Signed-off-by:
Cédric Le Goater <clg@kaod.org> Reviewed-by:
-
Christophe Leroy authored
max_mapnr is used by virt_addr_valid() to check if a linear address is valid. It must only include lowmem PFNs, like other architectures. Problem detected on a system with 1G mem (Only 768M are mapped), with CONFIG_DEBUG_VIRTUAL and CONFIG_TEST_DEBUG_VIRTUAL, it didn't report virt_to_phys(VMALLOC_START), VMALLOC_START being 0xf1000000. Signed-off-by:
-
- 12 Oct, 2021 2 commits
-
-
Athira Rajeev authored
Patch adds support to include Sampled Instruction Address Register (SIAR) and Sampled Data Address Register (SDAR) SPRs as part of extended registers. Update the definition of PERF_REG_PMU_MASK_300/31 and PERF_REG_EXTENDED_MAX to include these SPR's. Signed-off-by:
Athira Rajeev <atrajeev@linux.vnet.ibm.com> Reviewed-by:
-
Athira Rajeev authored
PERF_REG_PMU_MASK_300 and PERF_REG_PMU_MASK_31 defines the mask value for extended registers. Current definition of these mask values uses hex constant and does not use registers by name, making it less readable. Patch refactor the macro values by or'ing together the actual register value constants. Also include PERF_REG_EXTENDED_MAX as part of enum definition. Suggested-by:
-
- 08 Oct, 2021 13 commits
-
-
Nathan Lynch authored
This comment likely refers to the obsolete DLPAR workflow where some resource state transitions were driven more directly from user space utilities, but it also seems to contradict itself: "Change isolate state to Isolate [...]" is at odds with the preceding sentences, and it does not relate at all to the code that follows. Remove it to prevent confusion. Signed-off-by:
Nathan Lynch <nathanl@linux.ibm.com> Reviewed-by:
Daniel Henrique Barboza <danielhb413@gmail.com> Signed-off-by:
-
Nathan Lynch authored
The core DLPAR code supports two actions (add and remove) and three subtypes of action: * By DRC index: the action is attempted on a single specified resource. This is the usual case for processors. * By indexed count: the action is attempted on a range of resources beginning at the specified index. This is implemented only by the memory DLPAR code. * By count: the lower layer (CPU or memory) is responsible for locating the specified number of resources to which the action can be applied. I cannot find any evidence of the "by count" subtype being used by drmgr or qemu for processors. And when I try to exercise this code, the add case does not work: $ ppc64_cpu --smt ; nproc SMT=8 24 $ printf "cpu remove count 2" > /sys/kernel/dlpar $ nproc 8 $ printf "cpu add count 2" > /sys/kernel/dlpar -bash: printf: write error: Invalid argument $ dmesg | tail -2 pseries-hotplug-cpu: Failed to find enough CPUs (1 of 2) to add dlpar: Could not handle DLPAR request "cpu add count 2" $ nproc 8 $ drmgr -c cpu -a -q 2 # this uses the by-index method Validating CPU DLPAR capability...yes. CPU 1 CPU 17 $ nproc 24 This is because find_drc_info_cpus_to_add() does not increment drc_index appropriately during its search. This is not hard to fix. But the _by_count() functions also have the property that they attempt to roll back all prior operations if the entire request cannot be satisfied, even though the rollback itself can encounter errors. It's not possible to provide transaction-like behavior at this level, and it's undesirable to have code that can only pretend to do that. Any users of these functions cannot know what the state of the system is in the error case. And the error paths are, to my knowledge, impossible to test without adding custom error injection code. Summary: * This code has not worked reliably since its introduction. * There is no evidence that it is used. * It contains questionable rollback behaviors in error paths which are difficult to test. So let's remove it. Fixes: ac713800 ("powerpc/pseries: Add CPU dlpar remove functionality") Fixes: 90edf184 ("powerpc/pseries: Add CPU dlpar add functionality") Fixes: b015f6bc ("powerpc/pseries: Add cpu DLPAR support for drc-info property") Signed-off-by:
-
Nathan Lynch authored
If, due to bugs elsewhere, we get into unregister_cpu_online() with a CPU that isn't marked hotpluggable, we can emit a warning and return an appropriate error instead of crashing. Signed-off-by:
-
Nathan Lynch authored
On pseries, cache nodes in the device tree can be added and removed by the CPU DLPAR code as well as the partition migration (mobility) code. PowerVM partitions in dedicated processor mode typically have L2 and L3 cache nodes. The CPU DLPAR code has the following shortcomings: * Cache nodes returned as siblings of a new CPU node by ibm,configure-connector are silently discarded; only the CPU node is added to the device tree. * Cache nodes which become unreferenced in the processor removal path are not removed from the device tree. This can lead to duplicate nodes when the post-migration device tree update code replaces cache nodes. This is long-standing behavior. Presumably it has gone mostly unnoticed because the two bugs have the property of obscuring each other in common simple scenarios (e.g. remove a CPU and add it back). Likely you'd notice only if you cared to inspect the device tree or the sysfs cacheinfo information. Booted with two processors: $ pwd /sys/firmware/devicetree/base/cpus $ ls -1d */ l2-cache@2010/ l2-cache@2011/ l3-cache@3110/ l3-cache@3111/ PowerPC,POWER9@0/ PowerPC,POWER9@8/ $ lsprop */l2-cache l2-cache@2010/l2-cache 00003110 (12560) l2-cache@2011/l2-cache 00003111 (12561) PowerPC,POWER9@0/l2-cache 00002010 (8208) PowerPC,POWER9@8/l2-cache 00002011 (8209) $ ls /sys/devices/system/cpu/cpu0/cache/ index0 index1 index2 index3 After DLPAR-adding PowerPC,POWER9@10, we see that its associated cache nodes are absent, its threads' L2+L3 cacheinfo is unpopulated, and it is missing a cache level in its sched domain hierarchy: $ ls -1d */ l2-cache@2010/ l2-cache@2011/ l3-cache@3110/ l3-cache@3111/ PowerPC,POWER9@0/ PowerPC,POWER9@10/ PowerPC,POWER9@8/ $ lsprop PowerPC\,POWER9@10/l2-cache PowerPC,POWER9@10/l2-cache 00002012 (8210) $ ls /sys/devices/system/cpu/cpu16/cache/ index0 index1 $ grep . /sys/kernel/debug/sched/domains/cpu{0,8,16}/domain*/name /sys/kernel/debug/sched/domains/cpu0/domain0/name:SMT /sys/kernel/debug/sched/domains/cpu0/domain1/name:CACHE /sys/kernel/debug/sched/domains/cpu0/domain2/name:DIE /sys/kernel/debug/sched/domains/cpu8/domain0/name:SMT /sys/kernel/debug/sched/domains/cpu8/domain1/name:CACHE /sys/kernel/debug/sched/domains/cpu8/domain2/name:DIE /sys/kernel/debug/sched/domains/cpu16/domain0/name:SMT /sys/kernel/debug/sched/domains/cpu16/domain1/name:DIE When removing PowerPC,POWER9@8, we see that its cache nodes are left behind: $ ls -1d */ l2-cache@2010/ l2-cache@2011/ l3-cache@3110/ l3-cache@3111/ PowerPC,POWER9@0/ When DLPAR is combined with VM migration, we can get duplicate nodes. E.g. removing one processor, then migrating, adding a processor, and then migrating again can result in warnings from the OF core during post-migration device tree updates: Duplicate name in cpus, renamed to "l2-cache@2011#1" Duplicate name in cpus, renamed to "l3-cache@3111#1" and nodes with duplicated phandles in the tree, making lookup behavior unpredictable: $ lsprop l[23]-cache@*/ibm,phandle l2-cache@2010/ibm,phandle 00002010 (8208) l2-cache@2011#1/ibm,phandle 00002011 (8209) l2-cache@2011/ibm,phandle 00002011 (8209) l3-cache@3110/ibm,phandle 00003110 (12560) l3-cache@3111#1/ibm,phandle 00003111 (12561) l3-cache@3111/ibm,phandle 00003111 (12561) Address these issues by: * Correctly processing siblings of the node returned from dlpar_configure_connector(). * Removing cache nodes in the CPU remove path when it can be determined that they are not associated with other CPUs or caches. Use the of_changeset API in both cases, which allows us to keep the error handling in this code from becoming more complex while ensuring that the device tree cannot become inconsistent. Fixes: ac713800 ("powerpc/pseries: Add CPU dlpar remove functionality") Fixes: 90edf184 ("powerpc/pseries: Add CPU dlpar add functionality") Signed-off-by: -
Nathan Lynch authored
vcpu_is_preempted() can be used outside of preempt-disabled critical sections, yielding warnings such as: BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/185 caller is rwsem_spin_on_owner+0x1cc/0x2d0 CPU: 1 PID: 185 Comm: systemd-udevd Not tainted 5.15.0-rc2+ #33 Call Trace: [c000000012907ac0] [c000000000aa30a8] dump_stack_lvl+0xac/0x108 (unreliable) [c000000012907b00] [c000000001371f70] check_preemption_disabled+0x150/0x160 [c000000012907b90] [c0000000001e0e8c] rwsem_spin_on_owner+0x1cc/0x2d0 [c000000012907be0] [c0000000001e1408] rwsem_down_write_slowpath+0x478/0x9a0 [c000000012907ca0] [c000000000576cf4] filename_create+0x94/0x1e0 [c000000012907d10] [c00000000057ac08] do_symlinkat+0x68/0x1a0 [c000000012907d70] [c00000000057ae18] sys_symlink+0x58/0x70 [c000000012907da0] [c00000000002e448] system_call_exception+0x198/0x3c0 [c000000012907e10] [c00000000000c54c] system_call_common+0xec/0x250 The result of vcpu_is_preempted() is always used speculatively, and the function does not access per-cpu resources in a (Linux) preempt-unsafe way. Use raw_smp_processor_id() to avoid such warnings, adding explanatory comments. Fixes: ca3f969d ("powerpc/paravirt: Use is_kvm_guest() in vcpu_is_preempted()") Signed-off-by:
Srikar Dronamraju <srikar@linux.vnet.ibm.com> Signed-off-by:
-
Nathan Lynch authored
Add comments more clearly documenting that this function determines whether hypervisor-level preemption of the VM has occurred. Signed-off-by:
-
Nathan Lynch authored
When check_kvm_guest() succeeds in looking up a /hypervisor OF node, it returns without performing a matching put for the lookup, leaving the node's reference count elevated. Add the necessary call to of_node_put(), rearranging the code slightly to avoid repetition or goto. Fixes: 107c5500 ("powerpc/pseries: Add KVM guest doorbell restrictions") Signed-off-by:
-
Christophe Leroy authored
While investigating a lockup at startup on Powerbook 3400C, it was identified that the fbdev driver generates alignment exception at startup: --- interrupt: 600 at memset+0x60/0xc0 NIP: c0021414 LR: c03fc49c CTR: 00007fff REGS: ca021c10 TRAP: 0600 Tainted: G W (5.14.2-pmac-00727-g12a41fa69492) MSR: 00009032 <EE,ME,IR,DR,RI> CR: 44008442 XER: 20000100 DAR: cab80020 DSISR: 00017c07 GPR00: 00000007 ca021cd0 c14412e0 cab80000 00000000 00100000 cab8001c 00000004 GPR08: 00100000 00007fff 00000000 00000000 84008442 00000000 c0006fb4 00000000 GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000 GPR24: 00000000 81800000 00000320 c15fa400 c14d1878 00000000 c14d1800 c094e19c NIP [c0021414] memset+0x60/0xc0 LR [c03fc49c] chipsfb_pci_init+0x160/0x580 --- interrupt: 600 [ca021cd0] [c03fc46c] chipsfb_pci_init+0x130/0x580 (unreliable) [ca021d20] [c03a3a70] pci_device_probe+0xf8/0x1b8 [ca021d50] [c043d584] really_probe.part.0+0xac/0x388 [ca021d70] [c043d914] __driver_probe_device+0xb4/0x170 [ca021d90] [c043da18] driver_probe_device+0x48/0x144 [ca021dc0] [c043e318] __driver_attach+0x11c/0x1c4 [ca021de0] [c043ad30] bus_for_each_dev+0x88/0xf0 [ca021e10] [c043c724] bus_add_driver+0x190/0x22c [ca021e40] [c043ee94] driver_register+0x9c/0x170 [ca021e60] [c0006c28] do_one_initcall+0x54/0x1ec [ca021ed0] [c08246e4] kernel_init_freeable+0x1c0/0x270 [ca021f10] [c0006fdc] kernel_init+0x28/0x11c [ca021f30] [c0017148] ret_from_kernel_thread+0x14/0x1c Instruction dump: 7d4601a4 39490777 7d4701a4 39490888 7d4801a4 39490999 7d4901a4 39290aaa 7d2a01a4 4c00012c 4bfffe88 0fe00000 <4bfffe80> 9421fff0 38210010 48001970 This is due to 'dcbz' instruction being used on non-cached memory. 'dcbz' instruction is used by memset() to zeroize a complete cacheline at once, and memset() is not expected to be used on non cached memory. When performing a 'sparse' check on fbdev driver, it also appears that the use of memset() is unexpected: drivers/video/fbdev/chipsfb.c:334:17: warning: incorrect type in argument 1 (different address spaces) drivers/video/fbdev/chipsfb.c:334:17: expected void * drivers/video/fbdev/chipsfb.c:334:17: got char [noderef] __iomem *screen_base drivers/video/fbdev/chipsfb.c:334:15: warning: memset with byte count of 1048576 Use fb_memset() instead of memset(). fb_memset() is defined as memset_io() for powerpc. Fixes: 8c870933 ("[PATCH] ppc32: Remove CONFIG_PMAC_PBOOK") Reported-by:
Stan Johnson <userm57@yahoo.com> Signed-off-by:
-
Vasant Hegde authored
Signed-off-by:
Vasant Hegde <hegdevasant@linux.vnet.ibm.com> Reviewed-by:
-
Nick Desaulniers authored
UPD_CONSTR was previously a preprocessor define for an old GCC 4.9 inline asm bug with m<> constraints. Fixes: 6563139d ("powerpc: remove GCC version check for UPD_CONSTR") Suggested-by:
Nathan Chancellor <nathan@kernel.org> Suggested-by:
Nick Desaulniers <ndesaulniers@google.com> Reviewed-by:
-
Christophe Leroy authored
powerpc/mem: Fix arch/powerpc/mm/mem.c:53:12: error: no previous prototype for 'create_section_mapping' Commit 8e11d62e ("powerpc/mem: Add back missing header to fix 'no previous prototype' error") was supposed to fix the problem, but in the meantime commit a927bd6b ("mm: fix phys_to_target_node() and* memory_add_physaddr_to_nid() exports") moved create_section_mapping() prototype from asm/sparsemem.h to asm/mmzone.h Fixes: 8e11d62e ("powerpc/mem: Add back missing header to fix 'no previous prototype' error") Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
-
Niklas Schnelle authored
On powerpc, pci_dev_is_added() is called as part of SR-IOV fixups that are done under pcibios_add_device() which in turn is only called in pci_device_add() whih is called when a PCI device is scanned. pci_dev_assign_added() is called in pci_bus_add_device() which is only called after scanning the device. Thus pci_dev_is_added() is always false and can be dropped. Signed-off-by:
Niklas Schnelle <schnelle@linux.ibm.com> Reviewed-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Oliver O'Halloran <oohall@gmail.com> [mpe: Tweak change log slightly to reflect Oliver's comments] Signed-off-by:
-
Christophe Leroy authored
pmac_md doesn't exist anymore, remove stall declaration. Fixes: e8222502 ("[PATCH] powerpc: Kill _machine and hard-coded platform numbers") Signed-off-by:
-
