- 05 Mar, 2013 21 commits
-
-
Hans Verkuil authored
Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
- don't return -EINVAL for invalid field types, handle those as if it was FIELD_ANY. - the handling of FIELD_SEQ_BT/TB was wrong as well: if such field formats aren't supported, then fall back to FIELD_ANY instead of returning an error. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Set an initial frequencies when the driver is loaded. That way G_FREQUENCY will give a frequency that corresponds with reality. Signed-off-by:
-
Hans Verkuil authored
If no tuner is present, then disable the tuner and frequency ioctls. We can remove a number of checks from those ioctls testing for the presence of a tuner. Also remove some tuner type checks (now done by the core) and fix an error return when the prio check fails. Finally some 'unlikely' statements are removed since those only make sense in tightly often executed loops, otherwise they just clutter up the code. Signed-off-by:
-
Hans Verkuil authored
- Fix ENUM_INPUT audioset. - Fix incorrect input check in s_input. Signed-off-by:
-
Hans Verkuil authored
VIDIOC_DBG_G_CHIP_IDENT is a prerequisite for the G/S_REGISTER ioctls. In addition, add support to call G/S_REGISTER for supporting i2c devices. Signed-off-by:
-
Hans Verkuil authored
The querycap ioctl didn't support V4L2_CAP_DEVICE_CAPS and the radio device implemented audio and video inputs and s_std, which are not part of the radio API. Signed-off-by:
-
Hans Verkuil authored
Remove two maintainers: telegent.com no longer exists, so those email addresses are invalid as well. Added myself as co-maintainer and change the status to 'Odd Fixes'. Signed-off-by:
-
Hans Verkuil authored
ioctl debugging can now be done through the debug parameter in sysfs. Signed-off-by:
Huang Shijie <shijie8@gmail.com> Signed-off-by:
-
Hans Verkuil authored
Due to a poor administration of the driver state it wasn't possible to open a video or vbi device multiple times. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
The usual set of problems: the frequency isn't clamped to the frequency range, no tuner index check and the frequency isn't initialized properly on module load. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
- 04 Mar, 2013 19 commits
-
-
Hans Verkuil authored
This switch to v4l2_fh resolves the last v4l2_compliance issues with respect to control events and priority handling. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
The input and audio ioctls are only valid for video/vbi nodes. Signed-off-by:
-
Hans Verkuil authored
The driver already does locking, so it is safe to switch to unlocked_ioctl. Signed-off-by:
-
Hans Verkuil authored
This driver now passes the tuner and frequency tests of v4l2-compliance. It's the usual bugs: frequency wasn't clamped to the valid frequency range, incorrect tuner capabilities and tuner fields not filled in, missing test for invalid tuner index, no initial frequency and incorrect error handling. Signed-off-by:
-
Hans Verkuil authored
Set the correct parent for v4l2_device_register and don't set the name anymore (that's now deduced from the parent). Also remove an unnecessary forward reference and fix two weird looking log messages. Signed-off-by:
-
Frank Schaefer authored
Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Now that some devices initialize register 0x2a with different values, add the calculus formula, instead of hardcoding it. Signed-off-by: -
Mauro Carvalho Chehab authored
Up to now, the driver was simply assuming TV mode, 13 segs. Implement the logic to control the ISDB operational mode. Signed-off-by: -
Mauro Carvalho Chehab authored
Putting em28xx in suspend mode when a feed stops is just plain wrong. Every time a new PES filter is changed, the DVB demux code will stop the current feed, and then start a new one. If are there any code that switches off the frontend, via some GPIO setting, this would make the DVB fail. This condition was actually trigged with one device, during DVB scan, as, during scan, it is common that userspace apps to change the filter several times, in order to get all tables. Also, this is not needed at all, since the em28xx code already hooks into ops.ts_bus_ctrl(). This warrants that em28xx can check there if DVB frontend is in usage or not. The code there already puts the device on suspend mode, if the DVB frontend is not used (closed). Signed-off-by: -
Mauro Carvalho Chehab authored
Instead of using 3.3 MHz IF, use 4MHz. That's the standard value for the demod, and, while it can be adjusted, 3.3 MHz is out of the recommended range. So, let's stick with the default. With regards to the IF voltage level, instead of using 0.5 V(p-p) for IF, use 2V, giving a 12dB gain. The rationale is that, on PixelView SBTVD Hybrid, even 2V(p-p) would be in the nominal range for IF, as the maximum range on this particular device is 3V. A higher gain here should help to improve reception under weak signals. Signed-off-by: -
Mauro Carvalho Chehab authored
As the device got re-initialized, the stats should vanish until the device gets lock again. Signed-off-by: -
Mauro Carvalho Chehab authored
Signal strength is always available. There's no reason to reset it, as it has its own logic to reset it already. Signed-off-by: -
Mauro Carvalho Chehab authored
Always init the frontend when set_frontend is called. The rationale is: it was noticed that, on some devices, it fails to lock with a different channel. It seems that some other registers need to be restored to its initial state, when the channel changes. As it is better to reset everything, even wasting a few more miliseconds than to loose channel lock, let's change the logic to always reset. Signed-off-by: -
Mauro Carvalho Chehab authored
Use the AGC settings present on a newer device. The initial settings were taken from one of the first devices with mb86a20s, and there are several reports that this is not working properly on some places. So, instead of keeping using it, get the parameters taken from a newer device. Tests are welcomed. Tested also with cx231xx PixelView SBTVD Hybrid with no regressions noticed so far. Signed-off-by: -
Mauro Carvalho Chehab authored
Getting signal strength requires some loop poking with I2C. Don't let it happen too fast. Signed-off-by: -
Mauro Carvalho Chehab authored
A register typo made the calculation to not work. Fix it. Signed-off-by: -
Mauro Carvalho Chehab authored
State 9 means TS started to be output, and it should be associated with FE_HAS_SYNC. The mb86a20scan get CNR statistics at state 7, when frame sync is obtained. As CNR may help to adjust the antenna, provide it earlier. A latter patch could eventually start outputing MER measures earlier, but that would require a bigger change, and probably won't be better than the current way, as the time between changing from state 8 to 9 is generally lower than the time to get the stats collected. Signed-off-by:
-
