Use direct baud-rate encoding rather than divisors for supported baud
rates.

This restores the way baud rates were set prior to commit 8d48fdf6
("USB: PL2303: correctly handle baudrates above 115200") which added
divisor encoding, but also switched to the new encoding method for all
baudrates above 115200.

As noted by Frank Schäfer <fschaefer.oss@googlemail.com>, baud rate 500k
was later errounously added to the supported baud-rate table although
it can only be set using divisors.

Note that the current implementation could easily be extended to support
arbitrary non-standard baud rates using divisors (e.g. by falling back
to divisors when the table lookup fails).

Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add helper function for direct baud-rate encoding.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor baud-rate divisor handling.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enforce any baud-rate limits before doing table lookup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor supported baud-rate table lookup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rename baud-rate encoding function to match tty naming.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Encode all device-type specifics in a struct rather than testing for
device type and spreading such information throughout the driver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add quirk for legacy devices (type 0 and 1) rather than testing on
device type throughout the driver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge types 0 and 1, whose differences are unknown and have always been
treated the same.
Add TYPE_-prefix to both types.
Test for TYPE_01 (rather than !TYPE_HX) for legacy device quirks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use speed_t for baud rates throughout.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Implement line-status handling for Siemens phones as a quirk rather than
spreading such information all over the driver by matching on vendor and
and product ids.

Note that the SIEMENS_PRODUCT_ID_EF81, which was added after the
line-status handling for the other Siemens phones was fixed, might also
need this quirk.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove redundant get_line_request (the read back settings are never
used).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor and add error handling to line requests.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add error handling to set_control_lines.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add error handling and clean up vendor read and write functions.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use u16 rather than __u16.
Fix multi-line comment style.
Remove some comments.
Remove unnecessary whitespace and add some where appropriate.
Drop DRIVER_DESC define.
Merge and simplify multi-line error message.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove bogus MSR wait-queue wake up from process_read_urb which never
updates the MSR flags.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Switch to generic tiocmiwait rather than rely on a custom implementation
using racy interruptible_sleep_on().

Note that this driver is mostly stubbed out so neither version of
tiocmiwait will actually work until someone implements
f81232_update_line_status().
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove bogus call to wake up delta_msr_wait from process_read_urb where
the MSR status is never updated (only the LSR bits are masked out).

Comment that the wake-up call should made in f81232_update_line_status
when the MSR status changes.

Note that this driver is still mostly stubbed out.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove redundant error messages on allocation failures, which have
already been logged.

Cc: Joe Perches <joe@perches.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove redundant ioctl debugging from subdrivers. The ioctl request code
has already been logged by usb-serial core.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Declare device-id tables as const where possible.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some PL2303 devices are known to lose bytes if you change serial
settings even to the same values as before. Avoid this by comparing the
encoded settings with the previsouly used ones before configuring the
device.

The common case was fixed by commit bf5e5834 ("pl2303: Fix mode
switching regression"), but this problem was still possible to trigger,
for instance, by using the TCSETS2-interface to repeatedly request
115201 baud, which gets mapped to 115200 and thus always triggers a
settings update.

Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Felipe writes:

usb: changes for v3.14 merge window

This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:

New drivers:
	- Keystone PHY driver and DWC3 Glue Layer
	- Aeroflex Gaisler GRUSBDC
	- Tahvo PHY driver for N770
	- JZ4740 MUSB gluer Layer
	- Broadcom PHY Driver

Important new features:
	- MUSB DSPS learned about suspend/resume
	- New quirk_ep_out_aligned_size flag added to struct usb_gadget
	- DWC3 initializes the new quirk flag so gadget drivers can use it.
	- AM335x PHY Driver learns about remote wakeup
	- Renesas USBHS now requests DMA Engine only once
	- s3c-hsotg is now re-used on Broadcom devices
	- USB PHY layer now makes sure to initialize the notifier for all
		drivers
	- omap-control learned about TI's new AM437x devices
	- few other usb gadget/function drivers learned about the new
		configfs-based binding.

Misc Fixes and Clean Ups:
	- Several sparse fixes all over the place
	- Removal of redundant of_match_ptr()
	- r-car gen2 phy now uses usb_add_phy_dev()
	- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
	- conversion to clk_prepare/clk_unprepare on r8a66597-udc
	- some randconfig errors and build warnings were fixed
	- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>

Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Removing the check to usb_disable() before registering the platform
driver allows to build this driver when !USB && USB_GADGET, to be
used in gadget-only mode.

Also, use module_platform_driver() to register the platform driver.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This resolves the merge issue with drivers/usb/host/ohci-at91.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e117e742 (usb: gadget: add "maxpacket_limit"
field to struct usb_ep) added a build warning to
at91_udc when it passed the wrong argument to
usb_ep_set_maxpacket_limit().

Fix this by passing correct argument.
Signed-off-by: Felipe Balbi <balbi@ti.com>

This adds an UDC driver for GRUSBDC USB Device Controller cores available in the
GRLIB VHDL IP core library. The driver only supports DMA mode.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add a driver for the internal Broadcom Kona USB 2.0 PHY found
on the BCM281xx family of SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add a binding that describes the Broadcom Kona USB2 PHY found
on the BCM281xx family of SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Adds support for querying the phy bus width from the generic phy
subsystem. Configure UTMI bus width in GUSBCFG based on this value.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Adds support for the generic PHY subsystem. Generic PHY
support is probed and then the driver falls back to checking
for an old style USB PHY and pdata if not found.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Enable support for the dwc2 binding.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Remove unused Samsung-specific machine include and Kconfig
dependency on S3C.
Signed-off-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

dwc2/s3c-hsotg require a single clock to be specified and optionally
a generic phy. On the s3c-hsotg driver old style USB phy support is
present as a fallback so the generic phy properties are optional.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This adds a pair of APIs that allows the generic PHY subsystem to
provide information on the PHY bus width. The PHY provider driver may
use phy_set_bus_width() to set the bus width that the PHY supports.
The controller driver may then use phy_get_bus_width() to fetch the
PHY bus width in order to properly configure the controller.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Linux 3.13-rc5

* tag 'v3.13-rc5': (231 commits)
  Linux 3.13-rc5
  aio: clean up and fix aio_setup_ring page mapping
  aio/migratepages: make aio migrate pages sane
  aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
  Don't set the INITRD_COMPRESS environment variable automatically
  mm: fix build of split ptlock code
  pstore: Don't allow high traffic options on fragile devices
  mm: do not allocate page->ptl dynamically, if spinlock_t fits to long
  mm: page_alloc: revert NUMA aspect of fair allocation policy
  Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy"
  mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support
  qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
  target: Remove extra percpu_ref_init
  arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
  ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
  target/file: Update hw_max_sectors based on current block_size
  iser-target: Move INIT_WORK setup into isert_create_device_ib_res
  iscsi-target: Fix incorrect np->np_thread NULL assignment
  mm/hugetlb: check for pte NULL pointer in __page_check_address()
  fix build with make 3.80
  ...

Conflicts:
	drivers/usb/phy/Kconfig

This USB controller can work in as host-only, gadget-only or dual-role
modes. Rework the dependency on the USB and USB_GADGET configs in order
to allow building the driver when !USB or !USG_GADGET.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Some module names are not up to date in Kconfig help texts. Fix that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>