- 11 Jul, 2011 1 commit
-
-
Tejun Heo authored
Commit 2706a0bf ("x86, NUMA: Enable CONFIG_AMD_NUMA on 32bit too") enabled AMD NUMA for 32bit too. Unfortunately, SPARSEMEM on 32bit had rather coarse (512MiB) addr->node mapping granularity due to lack of space in page->flags. This led to boot failure on certain AMD NUMA machines which had 128MiB alignment on nodes. Patches to properly detect this condition and reject NUMA configuration are posted[1] but deemed too pervasive for merge at this point (-rc6). Disable AMD NUMA for 32bit for now and re-enable once the detection logic is merged. [1] http://thread.gmane.org/gmane.linux.kernel/1161279/focus=1162583Reported-by:
Hans Rosenfeld <hans.rosenfeld@amd.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Conny Seidel <conny.seidel@amd.com> Link: http://lkml.kernel.org/r/20110711083432.GC943@htj.dyndns.orgSigned-off-by:
Ingo Molnar <mingo@elte.hu>
-
- 10 Jul, 2011 7 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/stagingLinus Torvalds authored
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: hwmon: (pmbus) Improve auto-detection of temperature status register hwmon: (lm95241) Fix negative temperature results hwmon: (lm95241) Fix chip detection code
-
Guenter Roeck authored
It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1. Improve temperature status register detection to address this condition. Reported-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
Guenter Roeck <guenter.roeck@ericsson.com> Acked-by:
-
Guenter Roeck authored
Negative temperatures were returned in degrees C instead of milli-Degrees C. Also, negative temperatures were reported for remote temperature sensors even if the chip was configured for positive-only results. Fix by detecting temperature modes, and by treating negative temperatures similar to positive temperatures, with appropriate sign extension. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ALSA: hda - Fix a copmile warning ASoC: ak4642: fixup snd_soc_update_bits mask for PW_MGMT2 ALSA: hda - Change all ADCs for dual-adc switching mode for Realtek ASoC: Manage WM8731 ACTIVE bit as a supply widget ASoC: Don't set invalid name string to snd_card->driver field ASoC: Ensure we delay long enough for WM8994 FLL to lock when starting ASoC: Tegra: I2S: Ensure clock is enabled when writing regs ASoC: Fix Blackfin I2S _pointer() implementation return in bounds values ASoC: tlv320aic3x: Do soft reset to codec when going to bias off state ASoC: tlv320aic3x: Don't sync first two registers from register cache audio: tlv320aic26: fix PLL register configuration
-
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI: conditional resource-reallocation through kernel parameter pci=realloc
-
Linus Torvalds authored
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm: ARM: 6994/1: smp_twd: Fix typo in 'twd_timer_rate' printing ARM: 6987/1: l2x0: fix disabling function to avoid deadlock ARM: 6966/1: ep93xx: fix inverted RTS/DTR signals on uart1 ARM: 6980/1: mmci: use StartBitErr to detect bad connections ARM: 6979/1: mach-vt8500: add forgotten irq_data conversion ARM: move memory layout sanity checking before meminfo initialization ARM: 6990/1: MAINTAINERS: add entry for ARM PMU profiling and debugging ARM: 6989/1: perf: do not start the PMU when no events are present ARM: dmabounce: fix map_single() error return value
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/radeon/kms: clean up multiple crtc handling for evergreen+ (v2)
-
- 09 Jul, 2011 18 commits
-
-
Takashi Iwai authored
-
Takashi Iwai authored
It's harmless but annyoing. sound/pci/hda/patch_realtek.c: In function ‘alc_cap_getput_caller’: sound/pci/hda/patch_realtek.c:2722:9: warning: ‘err’ may be used uninitialized in this function Signed-off-by:Takashi Iwai <tiwai@suse.de>
-
Takashi Iwai authored
Merge branch 'for-3.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into fix/asoc
-
Linus Torvalds authored
Merge branch 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung * 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: S3C2440: fix section mismatch on mini2440 ARM: S3C24XX: drop return codes in void function of dma.c ARM: S3C24XX: don't use uninitialized variable in dma.c ARM: EXYNOS4: Set appropriate I2C device variant ARM: S5PC100: Fix for compilation error spi/s3c64xx: Bug fix for SPI with different FIFO level ARM: SAMSUNG: Add tx_st_done variable ARM: EXYNOS4: Address a section mismatch w/ suspend issue. ARM: S5P: Fix bug on init of PWMTimers for HRTimer ARM: SAMSUNG: header file revised to prevent declaring duplicated ARM: EXYNOS4: fix improper gpio configuration ARM: EXYNOS4: Fix card detection for sdhci 0 and 2
-
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: regulator: max8997: Fix setting inappropriate value for ramp_delay variable regulator: db8500-prcmu: small fixes regulator: max8997: remove dependency on platform_data pointer regulator: MAX8997: Fix for divide by zero error regulator: max8952 - fix wrong gpio valid check
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstableLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: btrfs: fix oops when doing space balance Btrfs: don't panic if we get an error while balancing V2 btrfs: add missing options displayed in mount output
-
Bjorn Helgaas authored
Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Wolfram Sang authored
This driver handles the variants pca9530-pca9533, so it chose the name "pca953x". However, there is a gpio driver which decided on the same name. As a result, those two can't be loaded at the same time. Add a subsystem prefix to make the driver name unique. Device matching will not suffer, because both are I2C drivers which match using a i2c_device_id-table which is not altered. Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Acked-by:
-
Bob Liu authored
remap_pfn_range() means map physical address pfn<<PAGE_SHIFT to user addr. For nommu arch it's implemented by vma->vm_start = pfn << PAGE_SHIFT which is wrong acroding the original meaning of this function. And some driver developer using remap_pfn_range() with correct parameter will get unexpected result because vm_start is changed. It should be implementd like addr = pfn << PAGE_SHIFT but which is meanless on nommu arch, this patch just make it simply return. Parameter name and setting of vma->vm_flags also be fixed. Signed-off-by:
Bob Liu <lliubbo@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: David Howells <dhowells@redhat.com> Acked-by:
Greg Ungerer <gerg@uclinux.org> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Bob Liu <lliubbo@gmail.com> Cc: <stable@kernel.org> Signed-off-by:
-
Jean-François Dagenais authored
This fixes a regression in 3.0 reported by Paul Parsons regarding the removal of the msleep(1) in the ds1wm_reset() function: : The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying" : error messages on an HP iPAQ hx4700 PDA (XScale-PXA270): : : <snip> : Driver for 1-wire Dallas network protocol. : DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko : 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko : ds1wm ds1wm: pass: 1 bus error, retrying : ds1wm ds1wm: pass: 2 bus error, retrying : ds1wm ds1wm: pass: 3 bus error, retrying : ds1wm ds1wm: pass: 4 bus error, retrying : ds1wm ds1wm: pass: 5 bus error, retrying : ... : : The visible result is that the battery charging LED is erratic; sometimes : it works, mostly it doesn't. : : The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1, : 3.0-rc2, or 3.0-rc3. This sleep should not be required on normal circuitry provided the pull-ups on the bus are correctly adapted to the slaves. Unfortunately, this is not always the case. The sleep is restored but as a parameter to the probe function in the pdata. [akpm@linux-foundation.org: coding-style fixes] Reported-by:
Paul Parsons <lost.distance@yahoo.com> Tested-by:
Jean-François Dagenais <dagenaisj@sonatest.com> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by:
-
KAMEZAWA Hiroyuki authored
commit 889976db ("memcg: reclaim memory from nodes in round-robin order") adds an numa node round-robin for memcg. But the information is updated once per 10sec. This patch changes the update trigger from jiffies to memcg's event count. After this patch, numa scan information will be updated when we see 1024 events of pagein/pageout under a memcg. [akpm@linux-foundation.org: attempt to repair code layout] Signed-off-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Ying Han <yinghan@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp> Signed-off-by:
-
KAMEZAWA Hiroyuki authored
Now, in mem_cgroup_hierarchical_reclaim(), mem_cgroup_local_usage() is used for checking whether the memcg contains reclaimable pages or not. If no pages in it, the routine skips it. But, mem_cgroup_local_usage() contains Unevictable pages and cannot handle "noswap" condition correctly. This doesn't work on a swapless system. This patch adds test_mem_cgroup_reclaimable() and replaces mem_cgroup_local_usage(). test_mem_cgroup_reclaimable() see LRU counter and returns correct answer to the caller. And this new function has "noswap" argument and can see only FILE LRU if necessary. [akpm@linux-foundation.org: coding-style fixes] [akpm@linux-foundation.org: fix kerneldoc layout] Signed-off-by:
-
Shaohua Li authored
__tlb_remove_page() switches to a new batch page, but still checks space in the old batch. This check always fails, and causes a forced tlb flush. Signed-off-by:
Shaohua Li <shaohua.li@intel.com> Acked-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by:
-
Mel Gorman authored
During allocator-intensive workloads, kswapd will be woken frequently causing free memory to oscillate between the high and min watermark. This is expected behaviour. Unfortunately, if the highest zone is small, a problem occurs. When balance_pgdat() returns, it may be at a lower classzone_idx than it started because the highest zone was unreclaimable. Before checking if it should go to sleep though, it checks pgdat->classzone_idx which when there is no other activity will be MAX_NR_ZONES-1. It interprets this as it has been woken up while reclaiming, skips scheduling and reclaims again. As there is no useful reclaim work to do, it enters into a loop of shrinking slab consuming loads of CPU until the highest zone becomes reclaimable for a long period of time. There are two problems here. 1) If the returned classzone or order is lower, it'll continue reclaiming without scheduling. 2) if the highest zone was marked unreclaimable but balance_pgdat() returns immediately at DEF_PRIORITY, the new lower classzone is not communicated back to kswapd() for sleeping. This patch does two things that are related. If the end_zone is unreclaimable, this information is communicated back. Second, if the classzone or order was reduced due to failing to reclaim, new information is not read from pgdat and instead an attempt is made to go to sleep. Due to this, it is also necessary that pgdat->classzone_idx be initialised each time to pgdat->nr_zones - 1 to avoid re-reads being interpreted as wakeups. Signed-off-by:
Mel Gorman <mgorman@suse.de> Reported-by:
Pádraig Brady <P@draigBrady.com> Tested-by:
Andrew Lutomirski <luto@mit.edu> Acked-by:
Rik van Riel <riel@redhat.com> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@kernel.org> Signed-off-by:
-
Mel Gorman authored
When deciding if kswapd is sleeping prematurely, the classzone is taken into account but this is different to what balance_pgdat() and the allocator are doing. Specifically, the DMA zone will be checked based on the classzone used when waking kswapd which could be for a GFP_KERNEL or GFP_HIGHMEM request. The lowmem reserve limit kicks in, the watermark is not met and kswapd thinks it's sleeping prematurely keeping kswapd awake in error. Signed-off-by:
Minchan Kim <minchan.kim@gmail.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@kernel.org> Signed-off-by:
-
Mel Gorman authored
During allocator-intensive workloads, kswapd will be woken frequently causing free memory to oscillate between the high and min watermark. This is expected behaviour. When kswapd applies pressure to zones during node balancing, it checks if the zone is above a high+balance_gap threshold. If it is, it does not apply pressure but it unconditionally shrinks slab on a global basis which is excessive. In the event kswapd is being kept awake due to a high small unreclaimable zone, it skips zone shrinking but still calls shrink_slab(). Once pressure has been applied, the check for zone being unreclaimable is being made before the check is made if all_unreclaimable should be set. This miss of unreclaimable can cause has_under_min_watermark_zone to be set due to an unreclaimable zone preventing kswapd backing off on congestion_wait(). Signed-off-by:
KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@kernel.org> Signed-off-by:
-
Mel Gorman authored
During allocator-intensive workloads, kswapd will be woken frequently causing free memory to oscillate between the high and min watermark. This is expected behaviour. Unfortunately, if the highest zone is small, a problem occurs. This seems to happen most with recent sandybridge laptops but it's probably a co-incidence as some of these laptops just happen to have a small Normal zone. The reproduction case is almost always during copying large files that kswapd pegs at 100% CPU until the file is deleted or cache is dropped. The problem is mostly down to sleeping_prematurely() keeping kswapd awake when the highest zone is small and unreclaimable and compounded by the fact we shrink slabs even when not shrinking zones causing a lot of time to be spent in shrinkers and a lot of memory to be reclaimed. Patch 1 corrects sleeping_prematurely to check the zones matching the classzone_idx instead of all zones. Patch 2 avoids shrinking slab when we are not shrinking a zone. Patch 3 notes that sleeping_prematurely is checking lower zones against a high classzone which is not what allocators or balance_pgdat() is doing leading to an artifical belief that kswapd should be still awake. Patch 4 notes that when balance_pgdat() gives up on a high zone that the decision is not communicated to sleeping_prematurely() This problem affects 2.6.38.8 for certain and is expected to affect 2.6.39 and 3.0-rc4 as well. If accepted, they need to go to -stable to be picked up by distros and this series is against 3.0-rc4. I've cc'd people that reported similar problems recently to see if they still suffer from the problem and if this fixes it. This patch: correct the check for kswapd sleeping in sleeping_prematurely() During allocator-intensive workloads, kswapd will be woken frequently causing free memory to oscillate between the high and min watermark. This is expected behaviour. A problem occurs if the highest zone is small. balance_pgdat() only considers unreclaimable zones when priority is DEF_PRIORITY but sleeping_prematurely considers all zones. It's possible for this sequence to occur 1. kswapd wakes up and enters balance_pgdat() 2. At DEF_PRIORITY, marks highest zone unreclaimable 3. At DEF_PRIORITY-1, ignores highest zone setting end_zone 4. At DEF_PRIORITY-1, calls shrink_slab freeing memory from highest zone, clearing all_unreclaimable. Highest zone is still unbalanced 5. kswapd returns and calls sleeping_prematurely 6. sleeping_prematurely looks at *all* zones, not just the ones being considered by balance_pgdat. The highest small zone has all_unreclaimable cleared but the zone is not balanced. all_zones_ok is false so kswapd stays awake This patch corrects the behaviour of sleeping_prematurely to check the zones balance_pgdat() checked. Signed-off-by: -
Guenter Roeck authored
The LM95241 driver accepts every chip ID equal to or larger than 0xA4 as its own, and other chips such as LM95245 use chip IDs in the accepted ID range. This results in false chip detection. Fix problem by accepting only the known LM95241 chip ID. Signed-off-by:
-
- 08 Jul, 2011 14 commits
-
-
Ram Pai authored
Multiple attempts to dynamically reallocate pci resources have unfortunately lead to regressions. Though we continue to fix the regressions and fine tune the dynamic-reallocation behavior, we have not reached a acceptable state yet. This patch provides a interim solution. It disables dynamic reallocation by default, but adds the ability to enable it through pci=realloc kernel command line parameter. Tested-by:Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Ram Pai <linuxram@us.ibm.com> Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org>
-
Donggeun Kim authored
The ramp_delay variable can be set lower than the desired value. This patch fixes it. Signed-off-by:
Donggeun Kim <dg77.kim@samsung.com> Signed-off-by:
MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by:
KyungMin Park <kyungmin.park@samsung.com> Acked-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
Liam Girdwood <lrg@slimlogic.co.uk>
-
Axel Lin authored
Small cleanups for better readability. Signed-off-by:
Axel Lin <axel.lin@gmail.com> Acked-by:
-
MyungJoo Ham authored
The platform_data (pdata) may be pointing to __initdata section, which may be free'd from the memory. The dependency on pdata in non-init functions is removed in this patch to allow platform to declare __initdata for platform data. Signed-off-by:
-
Tushar Behera authored
Currently, ramp_delay variable is used uninitialzed in max8997_set_voltage_ldobuck which gets called through regulator_register calls. To fix the problem, in max8997_pmic_probe, ramp_delay initialization code is moved before calls to regulator_register. Cc: Liam Girdwood <lrg@ti.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: MyungJoo Ham <myungjoo.ham@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
Tushar Behera <tushar.behera@linaro.org> Acked-by:
-
Jonghwan Choi authored
Signed-off-by:
Jonghwan Choi <jhbird.choi@samsung.com> Acked-by:
-
Alex Deucher authored
evergreen+ asics have 2-6 crtcs. Don't access crtc registers for crtc regs that don't exist as they have very high latency and may cause problems on some asics. The previous code missed a few cases and was not fine grained enough (missed the 4 crtc case for example). Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=38800 v2: fix typo noticed by Chris Bandy <cbandy@jbandy.com> Signed-off-by:
Alex Deucher <alexdeucher@gmail.com> Reviewed-by:
Michel Dänzer <michel@daenzer.net> Tested-by:
Simon Farnsworth <simon.farnsworth@onelan.co.uk> Signed-off-by:
Dave Airlie <airlied@redhat.com>
-
git://git.secretlab.ca/git/linux-2.6Linus Torvalds authored
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6: gpio/langwell_gpio: ack the correct bit for langwell gpio interrupts
-
git://oss.sgi.com/xfs/xfsLinus Torvalds authored
* 'for-linus' of git://oss.sgi.com/xfs/xfs: xfs: unpin stale inodes directly in IOP_COMMITTED
-
Linus Torvalds authored
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: omap: drop __initdata tags from static struct platform_device declarations
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/kms: allow drm_mode_group with no objects drm/radeon/kms: free ib pool on module unloading drm/radeon/kms: fix typo in evergreen disp int status register drm/radeon/kms: fix typo in IH_CNTL swap bitfield
-
Mathias Nyman authored
The wrong bit was masked when acking langwell gpio interrupts. Reason for maskig the wrong bit was probably because__ffs() and ffs() functions return bit indexes differently (0..31 vs 1..32) This fixes langwell based devices from hanging when a gpio interrupt is triggered and undoes the breakage which occurred in change set 732063b9Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
Grant Likely <grant.likely@secretlab.ca>
-
Wolfram Sang authored
If mini2440_init() is in __init, mini2440_parse_features() should also be in __init. Fixes: (.text+0x9adc): Section mismatch in reference from the function mini2440_parse_features.clone.0() to the (unknown reference) .init.data:(unknown) The function mini2440_parse_features.clone.0() references the (unknown reference) __initdata (unknown). Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Wolfram Sang authored
Commit bb072c3c (ARM / Samsung: Use struct syscore_ops for "core" power management) turned s3c2410_dma_resume_chan() from int to void. So, drop the actual return values, too. Fixes: arch/arm/plat-s3c24xx/dma.c: In function 's3c2410_dma_resume_chan': arch/arm/plat-s3c24xx/dma.c:1238:3: warning: 'return' with a value, in function returning void arch/arm/plat-s3c24xx/dma.c:1250:2: warning: 'return' with a value, in function returning void Signed-off-by:
Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by:
-
