The driver's handling of DMA buffers for non-aligned transfers
was kind of nuts. For IN transfers, it left the URB DMA buffer
mapped until the transfer completed, then synced it, copied the
data from the bounce buffer, then synced it again.

Instead of that, just call usb_hcd_unmap_urb_for_dma() to unmap
the buffer before starting the transfer. Then no syncing is
required when doing the copy. This should also allow handling of
other types of mappings besides just dma_map_single() ones.

Also reduce the size of the bounce buffer allocation for Isoc
endpoints to 3K, since that's the largest possible transfer size.

Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clip max_transfer_size to 65535 for host. dwc2_hc_setup_align_buf()
allocates coherent buffers with this size, and if it's too large we
can exhaust the coherent DMA pool.

Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When device is stopped or suspended clock is not needed so we
can disable it for this time.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Because we have not enough memory to have each TX FIFO of size at least
3072 bytes (the maximum single packet size with 3 transactions per
microframe), we create four FIFOs of lenght 1024, and four of length
3072 bytes, and assing them to endpoints dynamically according to
maxpacket size value of given endpoint.

Up to now there were initialized 16 TX FIFOs, but we use only 8 IN
endpoints, so we can split available memory for 8 FIFOs to have more
memory for each one.

It needed to do some small modifications in few places in code, because
there was assumption that TX FIFO numbers assigned to endpoints are the
same as the endpoint numbers, which is not true since we have dynamic
FIFO assigning.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Print warning if FIFOs are configured in such a way that they don't fit
into the SPRAM available on the s3c hsotg module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some DWC2/s3c-hsotg debug messages are really useless for typical user,
so hide them behind dev_dbg().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Adjust the debug text to the name of the printed variable.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Felipe writes:

usb: changes for v3.18 merge window

Quite big pull request this time. Audio and UVC gadgets
can now be used with our configfs-based binding. We have
three PHY drivers being removed because a new one has been
added using new PHY framework.

Gadget framework got a new ->reset callback preparing for
some other changes to come on next merge window.

A few new drivers came in as well; among those we have a
new UDC driver from Xilinx and two new glue layers for
DWC3 (ST and Qualcomm).

DWC3 also learned about tracepoints which will help debugging
quite a bit.

Other than that, a big series of non-critical fixes and
cleanups.

All patches have been on linux-next for quite a bit of time
and I boot tested these changes on platforms I have access
to and work with mainline.
Signed-of-by: Felipe Balbi <balbi@ti.com>

This reverts commit be0a8887.

The original commit f2267089
(usb: gadget: composite: dequeue cdev->req before free it in
composite_dev_cleanup) ended up being reverted because it caused
more issues then fixed. We will also revert this counter part
commit so we start clean to properly add that idea back.

Cc: Li Jun <b47624@freescale.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>

This adds a bounce buffer that handles the end of OUT requests where
req.length is not divisible by ep->ep.maxpacket.

Before this, such requests were rejected as the DMA engine cannot
restrict itself to buffers that are smaller than ep->ep.maxpacket.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The state attribute is connected to the kobj of the udc, not the gadget.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

if we don't make sure to kill the timer, it could
expire after we have already gated our clocks.

That will trigger a Data Abort exception because
we would try to access register while clock is gated.

Fix that bug.

Cc: <stable@vger.kernel.org> # v3.14+
Fixes 869c5978 (usb: musb: dsps: add support for suspend and resume)
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use the local queue variable instead of computing it every time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The struct usb_endpoint_descriptor wMaxPacketSize field the struct
usb_ss_ep_comp_descriptor wBytesPerInterval field are stored in
little-endian format. Convert the values from CPU order to little endian
before storing the values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The function isn't called from outside of its compilation unit, make it
static.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch introduces virtual endpoint address mapping. It separates
function logic form physical endpoint addresses making it more hardware
independent.

Following modifications changes user space API, so to enable them user
have to switch on the FUNCTIONFS_VIRTUAL_ADDR flag in descriptors.

Endpoints are now refered using virtual endpoint addresses chosen by
user in endpoint descpriptors. This applies to each context when endpoint
address can be used:
- when accessing endpoint files in FunctionFS filesystemi (in file name),
- in setup requests directed to specific endpoint (in wIndex field),
- in descriptors returned by FUNCTIONFS_ENDPOINT_DESC ioctl.

In endpoint file names the endpoint address number is formatted as
double-digit hexadecimal value ("ep%02x") which has few advantages -
it is easy to parse, allows to easly recognize endpoint direction basing
on its name (IN endpoint number starts with digit 8, and OUT with 0)
which can be useful for debugging purpose, and it makes easier to introduce
further features allowing to use each endpoint number in both directions
to have more endpoints available for function if hardware supports this
(for example we could have ep01 which is endpoint 1 with OUT direction,
and ep81 which is endpoint 1 with IN direction).

Physical endpoint address can be still obtained using ioctl named
FUNCTIONFS_ENDPOINT_REVMAP, but now it's not neccesary to handle
USB transactions properly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Linux 3.17-rc5
Signed-off-by: Felipe Balbi <balbi@ti.com>

Conflicts:
	Documentation/devicetree/bindings/usb/mxs-phy.txt
	drivers/usb/phy/phy-mxs-usb.c

We need the USB fixes in there to build on top of in this branch for
3.18.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull vfs fixes from Al Viro:
 "double iput() on failure exit in lustre, racy removal of spliced
  dentries from ->s_anon in __d_materialise_dentry() plus a bunch of
  assorted RCU pathwalk fixes"

The RCU pathwalk fixes end up fixing a couple of cases where we
incorrectly dropped out of RCU walking, due to incorrect initialization
and testing of the sequence locks in some corner cases.  Since dropping
out of RCU walk mode forces the slow locked accesses, those corner cases
slowed down quite dramatically.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  be careful with nd->inode in path_init() and follow_dotdot_rcu()
  don't bugger nd->seq on set_root_rcu() from follow_dotdot_rcu()
  fix bogus read_seqretry() checks introduced in b37199e6
  move the call of __d_drop(anon) into __d_materialise_unique(dentry, anon)
  [fix] lustre: d_make_root() does iput() on dentry allocation failure

The performance regression that Josef Bacik reported in the pathname
lookup (see commit 99d263d4 "vfs: fix bad hashing of dentries") made
me look at performance stability of the dcache code, just to verify that
the problem was actually fixed.  That turned up a few other problems in
this area.

There are a few cases where we exit RCU lookup mode and go to the slow
serializing case when we shouldn't, Al has fixed those and they'll come
in with the next VFS pull.

But my performance verification also shows that link_path_walk() turns
out to have a very unfortunate 32-bit store of the length and hash of
the name we look up, followed by a 64-bit read of the combined hash_len
field.  That screws up the processor store to load forwarding, causing
an unnecessary hickup in this critical routine.

It's caused by the ugly calling convention for the "hash_name()"
function, and easily fixed by just making hash_name() fill in the whole
'struct qstr' rather than passing it a pointer to just the hash value.

With that, the profile for this function looks much smoother.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull parisc updates from Helge Deller:
 "The most important patch is a new Light Weigth Syscall (LWS) for 8,
  16, 32 and 64 bit atomic CAS operations which is required in order to
  be able to implement the atomic gcc builtins on our platform.

  Other than that, we wire up the seccomp, getrandom and memfd_create
  syscalls, fixes a minor off-by-one bug and a wrong printk string"

* 'parisc-3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Implement new LWS CAS supporting 64 bit operations.
  parisc: Wire up seccomp, getrandom and memfd_create syscalls
  parisc: dino: fix %d confusingly prefixed with 0x in format string
  parisc: sys_hpux: NUL terminator is one past the end

in the former we simply check if dentry is still valid after picking
its ->d_inode; in the latter we fetch ->d_inode in the same places
where we fetch dentry and its ->d_seq, under the same checks.

Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

return the value instead, and have path_init() do the assignment.  Broken by
"vfs: Fix absolute RCU path walk failures due to uninitialized seq number",
which was Cc-stable with 2.6.38+ as destination.  This one should go where
it went.

To avoid dummy value returned in case when root is already set (it would do
no harm, actually, since the only caller that doesn't ignore the return value
is guaranteed to have nd->root *not* set, but it's more obvious that way),
lift the check into callers.  And do the same to set_root(), to keep them
in sync.

Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull ntb driver bugfixes from Jon Mason:
 "NTB driver fixes for queue spread and buffer alignment.  Also, update
  to MAINTAINERS to reflect new e-mail address"

* tag 'ntb-3.17' of git://github.com/jonmason/ntb:
  ntb: Add alignment check to meet hardware requirement
  MAINTAINERS: update NTB info
  NTB: correct the spread of queues over mw's

Pull ARM irq chip fixes from Thomas Gleixner:
 "Another pile of ARM specific irq chip fixlets:

   - off by one bugs in the crossbar driver
   - missing annotations
   - a bunch of "make it compile" updates

  I pulled the lot today from Jason, but it has been in -next for at
  least a week"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: gic-v3: Declare rdist as __percpu pointer to __iomem pointer
  irqchip: gic: Make gic_default_routable_irq_domain_ops static
  irqchip: exynos-combiner: Fix compilation error on ARM64
  irqchip: crossbar: Off by one bugs in init
  irqchip: gic-v3: Tag all low level accessors __maybe_unused
  irqchip: gic-v3: Only define gic_peek_irq() when building SMP

irqchip fixes for v3.17 from Jason Cooper

 - GIC/GICV3: Various fixlets
 - crossbar: Fix off-by-one bug
 - exynos-combiner: Fix arm64 build error

The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Update my contact info to my personal email address and add Dave Jiang.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>

The detection of an uneven number of queues on the given memory windows
was not correct.  The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Signed-off-by: Jon Mason <jon.mason@intel.com>

read_seqretry() returns true on mismatch, not on match...

Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

and lock the right list there

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

double-free is a bad thing
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Merge branches 'locking-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull futex and timer fixes from Thomas Gleixner:
 "A oneliner bugfix for the jinxed futex code:

   - Drop hash bucket lock in the error exit path.  I really could slap
     myself for intruducing that bug while fixing all the other horror
     in that code three month ago ...

  and the timer department is not too proud about the following fixes:

   - Deal with a long standing rounding bug in the timeval to jiffies
     conversion.  It's a real issue and this fix fell through the cracks
     for quite some time.

   - Another round of alarmtimer fixes.  Finally this code gets used
     more widely and the subtle issues hidden for quite some time are
     noticed and fixed.  Nothing really exciting, just the itty bitty
     details which bite the serious users here and there"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Unlock hb->lock in futex_wait_requeue_pi() error path

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  alarmtimer: Lock k_itimer during timer callback
  alarmtimer: Do not signal SIGEV_NONE timers
  alarmtimer: Return relative times in timer_gettime
  jiffies: Fix timeval conversion to jiffies

The current LWS cas only works correctly for 32bit. The new LWS allows
for CAS operations of variable size.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Helge Deller <deller@gmx.de>

Josef Bacik found a performance regression between 3.2 and 3.10 and
narrowed it down to commit bfcfaa77 ("vfs: use 'unsigned long'
accesses for dcache name comparison and hashing"). He reports:

 "The test case is essentially

      for (i = 0; i < 1000000; i++)
              mkdir("a$i");

  On xfs on a fio card this goes at about 20k dir/sec with 3.2, and 12k
  dir/sec with 3.10.  This is because we spend waaaaay more time in
  __d_lookup on 3.10 than in 3.2.

  The new hashing function for strings is suboptimal for <
  sizeof(unsigned long) string names (and hell even > sizeof(unsigned
  long) string names that I've tested).  I broke out the old hashing
  function and the new one into a userspace helper to get real numbers
  and this is what I'm getting:

      Old hash table had 1000000 entries, 0 dupes, 0 max dupes
      New hash table had 12628 entries, 987372 dupes, 900 max dupes
      We had 11400 buckets with a p50 of 30 dupes, p90 of 240 dupes, p99 of 567 dupes for the new hash

  My test does the hash, and then does the d_hash into a integer pointer
  array the same size as the dentry hash table on my system, and then
  just increments the value at the address we got to see how many
  entries we overlap with.

  As you can see the old hash function ended up with all 1 million
  entries in their own bucket, whereas the new one they are only
  distributed among ~12.5k buckets, which is why we're using so much
  more CPU in __d_lookup".

The reason for this hash regression is two-fold:

 - On 64-bit architectures the down-mixing of the original 64-bit
   word-at-a-time hash into the final 32-bit hash value is very
   simplistic and suboptimal, and just adds the two 32-bit parts
   together.

   In particular, because there is no bit shuffling and the mixing
   boundary is also a byte boundary, similar character patterns in the
   low and high word easily end up just canceling each other out.

 - the old byte-at-a-time hash mixed each byte into the final hash as it
   hashed the path component name, resulting in the low bits of the hash
   generally being a good source of hash data.  That is not true for the
   word-at-a-time case, and the hash data is distributed among all the
   bits.

The fix is the same in both cases: do a better job of mixing the bits up
and using as much of the hash data as possible.  We already have the
"hash_32|64()" functions to do that.
Reported-by: Josef Bacik <jbacik@fb.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The hash_64() function historically does the multiply by the
GOLDEN_RATIO_PRIME_64 number with explicit shifts and adds, because
unlike the 32-bit case, gcc seems unable to turn the constant multiply
into the more appropriate shift and adds when required.

However, that means that we generate those shifts and adds even when the
architecture has a fast multiplier, and could just do it better in
hardware.

Use the now-cleaned-up CONFIG_ARCH_HAS_FAST_MULTIPLIER (together with
"is it a 64-bit architecture") to decide whether to use an integer
multiply or the explicit sequence of shift/add instructions.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It used to be an ad-hoc hack defined by the x86 version of
<asm/bitops.h> that enabled a couple of library routines to know whether
an integer multiply is faster than repeated shifts and additions.

This just makes it use the real Kconfig system instead, and makes x86
(which was the only architecture that did this) select the option.

NOTE! Even for x86, this really is kind of wrong.  If we cared, we would
probably not enable this for builds optimized for netburst (P4), where
shifts-and-adds are generally faster than multiplies.  This patch does
*not* change that kind of logic, though, it is purely a syntactic change
with no code changes.

This was triggered by the fact that we have other places that really
want to know "do I want to expand multiples by constants by hand or
not", particularly the hash generation code.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull device mapper fix from Mike Snitzer:
 "Fix a race in the DM cache target that caused dirty blocks to be
  marked as clean.  This could cause no writeback to occur or spurious
  dirty block counts"

* tag 'dm-3.17-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm cache: fix race causing dirty blocks to be marked as clean

Pull block fixes from Jens Axboe:
 "A small collection of fixes for the current rc series.  This contains:

   - Two small blk-mq patches from Rob Elliott, cleaning up error case
     at init time.

   - A fix from Ming Lei, fixing SG merging for blk-mq where
     QUEUE_FLAG_SG_NO_MERGE is the default.

   - A dev_t minor lifetime fix from Keith, fixing an issue where a
     minor might be reused before all references to it were gone.

   - Fix from Alan Stern where an unbalanced queue bypass caused SCSI
     some headaches when it does a series of add/del on devices without
     fully registrering the queue.

   - A fix from me for improving the scaling of tag depth in blk-mq if
     we are short on memory"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: scale depth and rq map appropriate if low on memory
  Block: fix unbalanced bypass-disable in blk_register_queue
  block: Fix dev_t minor allocation lifetime
  blk-mq: cleanup after blk_mq_init_rq_map failures
  blk-mq: pass along blk_mq_alloc_tag_set return values
  blk-merge: fix blk_recount_segments