Jose Abreu says:

====================
net: stmmac: Misc Fixes

Some small fixes for stmmac targeting -net. Detailed info in commit log.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, TX is given a budget which is consumed by stmmac_tx_clean()
and stmmac_rx() is given the remaining non-consumed budget.

This is wrong and in case we are sending a large number of packets this
can starve RX because remaining budget will be low.

Let's give always the same budget for RX and TX clean.

While at it, check if we missed any interrupts while we were in NAPI
callback by looking at DMA interrupt status.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RX Watchdog can be disabled by platform definitions but currently we are
initializing the descriptors before checking if Watchdog must be
disabled or not.

Fix this by checking earlier if user wants Watchdog disabled or not.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check if CBS is currently supported before trying to configure it in HW.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In DMA interrupt handler we were clearing all interrupts status, even
the ones that were not active. Fix this and only clear the active
interrupts.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit b7d0f08e, the enable / disable of PCI device is not
managed which will result in IO regions not being automatically unmapped.
As regions continue mapped it is currently not possible to remove and
then probe again the PCI module of stmmac.

Fix this by manually unmapping regions on remove callback.

Changes from v1:
- Fix build error

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Fixes: b7d0f08e ("net: stmmac: Fix WoL for PCI-based setups")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2019-01-11

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix TCP-BPF support for correctly setting the initial window
   via TCP_BPF_IW on an active TFO sender, from Yuchung.

2) Fix a panic in BPF's stack_map_get_build_id()'s ELF parsing on
   32 bit archs caused by page_address() returning NULL, from Song.

3) Fix BTF pretty print in kernel and bpftool when bitfield member
   offset is greater than 256. Also add test cases, from Yonghong.

4) Fix improper argument handling in xdp1 sample, from Ioana.

5) Install missing tcp_server.py and tcp_client.py files from
   BPF selftests, from Anders.

6) Add test_libbpf to gitignore in libbpf and BPF selftests,
   from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Yonghong Song says:

====================
The previous BTF kind_flag support patch set introduced a bug
for kernel bpffs pretty printing and another bug for bpftool
map pretty printing. If a bitfield struct member offset is
greater than 256 bits, printed value for that struct
member will be incorrect.

- Patch #1 fixed the bug in kernel bpffs pretty printing.
- Patch #2 enhanced the test_btf test case to cover the
           issue exposed by patch #1.
- Patch #3 fixed the bug in bpftool map pretty printing.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Commit 8772c8bc ("tools: bpftool: support pretty print
with kind_flag set") added bpftool map dump with kind_flag
support. When bitfield_size can be retrieved directly from
btf_member, function btf_dumper_bitfield() is called to
dump the bitfield. The implementation passed the
wrong parameter "bit_offset" to the function. The excepted
value is the bit_offset within a byte while the passed-in
value is the struct member offset.

This commit fixed the bug with passing correct "bit_offset"
with adjusted data pointer.

Fixes: 8772c8bc ("tools: bpftool: support pretty print with kind_flag set")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch modified test_btf pretty print test to cover
the bitfield with struct member equal to or greater 256.

Without the previous kernel patch fix, the modified test will fail:

  $ test_btf -p
  ......
  BTF pretty print array(#1)......unexpected pprint output
  expected: 0: {0,0,0,0x3,0x0,0x3,{0|[0,0,0,0,0,0,0,0]},ENUM_ZERO,4,0x1}
      read: 0: {0,0,0,0x3,0x0,0x3,{0|[0,0,0,0,0,0,0,0]},ENUM_ZERO,4,0x0}

  BTF pretty print array(#2)......unexpected pprint output
  expected: 0: {0,0,0,0x3,0x0,0x3,{0|[0,0,0,0,0,0,0,0]},ENUM_ZERO,4,0x1}
      read: 0: {0,0,0,0x3,0x0,0x3,{0|[0,0,0,0,0,0,0,0]},ENUM_ZERO,4,0x0}

  PASS:6 SKIP:0 FAIL:2

With the kernel fix, the modified test will succeed:
  $ test_btf -p
  ......
  BTF pretty print array(#1)......OK
  BTF pretty print array(#2)......OK
  PASS:8 SKIP:0 FAIL:0

Fixes: 9d5f9f70 ("bpf: btf: fix struct/union/fwd types with kind_flag")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Commit 9d5f9f70 ("bpf: btf: fix struct/union/fwd types
with kind_flag") introduced kind_flag and used bitfield_size
in the btf_member to directly pretty print member values.

The commit contained a bug where the incorrect parameters could be
passed to function btf_bitfield_seq_show(). The bits_offset
parameter in the function expects a value less than 8.
Instead, the member offset in the structure is passed.

The below is btf_bitfield_seq_show() func signature:
  void btf_bitfield_seq_show(void *data, u8 bits_offset,
                             u8 nr_bits, struct seq_file *m)
both bits_offset and nr_bits are u8 type. If the bitfield
member offset is greater than 256, incorrect value will
be printed.

This patch fixed the issue by calculating correct proper
data offset and bits_offset similar to non kind_flag case.

Fixes: 9d5f9f70 ("bpf: btf: fix struct/union/fwd types with kind_flag")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

linux 5.0-rc1 shows following warning on bpi-r2/mt7623 bootup:

[ 5.170597] WARNING: CPU: 3 PID: 1 at drivers/net/phy/phy.c:548 phy_start_aneg+0x110/0x144
[ 5.178826] called from state READY
....
[ 5.264111] [<c0629fd4>] (phy_start_aneg) from [<c0e3e720>] (mtk_init+0x414/0x47c)
[ 5.271630] r7:df5f5eec r6:c0f08c48 r5:00000000 r4:dea67800
[ 5.277256] [<c0e3e30c>] (mtk_init) from [<c07dabbc>] (register_netdevice+0x98/0x51c)
[ 5.285035] r8:00000000 r7:00000000 r6:c0f97080 r5:c0f08c48 r4:dea67800
[ 5.291693] [<c07dab24>] (register_netdevice) from [<c07db06c>] (register_netdev+0x2c/0x44)
[ 5.299989] r8:00000000 r7:dea2e608 r6:deacea00 r5:dea2e604 r4:dea67800
[ 5.306646] [<c07db040>] (register_netdev) from [<c06326d8>] (mtk_probe+0x668/0x7ac)
[ 5.314336] r5:dea2e604 r4:dea2e040
[ 5.317890] [<c0632070>] (mtk_probe) from [<c05a78fc>] (platform_drv_probe+0x58/0xa8)
[ 5.325670] r10:c0f86bac r9:00000000 r8:c0fbe578 r7:00000000 r6:c0f86bac r5:00000000
[ 5.333445] r4:deacea10
[ 5.335963] [<c05a78a4>] (platform_drv_probe) from [<c05a5248>] (really_probe+0x2d8/0x424)

maybe other boards using this generic driver are affected

v2:
optimization:

- phy_set_max_speed() is only needed if you want to reduce the
  max speed, typically if the PHY supports 1Gbps but the MAC
  supports 100Mbps only.

- The pause parameters are autonegotiated. Except you have a specific
  need you normally don't need to manually fiddle with this.

- phy_start_aneg() is called implicitly by the phylib state machine,
  you shouldn't call it manually except you have a good excuse.

- netif_carrier_on/netif_carrier_off in mtk_phy_link_adjust() isn't
  needed. It's done by phy_link_change() in phylib.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously upon SYN timeouts the sender recomputes the txhash to
try a different path. However this does not apply on the initial
timeout of SYN-data (active Fast Open). Therefore an active IPv6
Fast Open connection may incur one second RTO penalty to take on
a new path after the second SYN retransmission uses a new flow label.

This patch removes this undesirable behavior so Fast Open changes
the flow label just like the regular connections. This also helps
avoid falsely disabling Fast Open on the sender which triggers
after two consecutive SYN timeouts on Fast Open.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

A network device stack with multiple layers of bonding devices can
trigger a false positive lockdep warning. Adding lockdep nest levels
fixes this. Update the level on both enslave and unlink, to avoid the
following series of events ..

    ip netns add test
    ip netns exec test bash
    ip link set dev lo addr 00:11:22:33:44:55
    ip link set dev lo down

    ip link add dev bond1 type bond
    ip link add dev bond2 type bond

    ip link set dev lo master bond1
    ip link set dev bond1 master bond2

    ip link set dev bond1 nomaster
    ip link set dev bond2 master bond1

.. from still generating a splat:

    [  193.652127] ======================================================
    [  193.658231] WARNING: possible circular locking dependency detected
    [  193.664350] 4.20.0 #8 Not tainted
    [  193.668310] ------------------------------------------------------
    [  193.674417] ip/15577 is trying to acquire lock:
    [  193.678897] 00000000a40e3b69 (&(&bond->stats_lock)->rlock#3/3){+.+.}, at: bond_get_stats+0x58/0x290
    [  193.687851]
    	       but task is already holding lock:
    [  193.693625] 00000000807b9d9f (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0x58/0x290

    [..]

    [  193.851092]        lock_acquire+0xa7/0x190
    [  193.855138]        _raw_spin_lock_nested+0x2d/0x40
    [  193.859878]        bond_get_stats+0x58/0x290
    [  193.864093]        dev_get_stats+0x5a/0xc0
    [  193.868140]        bond_get_stats+0x105/0x290
    [  193.872444]        dev_get_stats+0x5a/0xc0
    [  193.876493]        rtnl_fill_stats+0x40/0x130
    [  193.880797]        rtnl_fill_ifinfo+0x6c5/0xdc0
    [  193.885271]        rtmsg_ifinfo_build_skb+0x86/0xe0
    [  193.890091]        rtnetlink_event+0x5b/0xa0
    [  193.894320]        raw_notifier_call_chain+0x43/0x60
    [  193.899225]        netdev_change_features+0x50/0xa0
    [  193.904044]        bond_compute_features.isra.46+0x1ab/0x270
    [  193.909640]        bond_enslave+0x141d/0x15b0
    [  193.913946]        do_set_master+0x89/0xa0
    [  193.918016]        do_setlink+0x37c/0xda0
    [  193.921980]        __rtnl_newlink+0x499/0x890
    [  193.926281]        rtnl_newlink+0x48/0x70
    [  193.930238]        rtnetlink_rcv_msg+0x171/0x4b0
    [  193.934801]        netlink_rcv_skb+0xd1/0x110
    [  193.939103]        rtnetlink_rcv+0x15/0x20
    [  193.943151]        netlink_unicast+0x3b5/0x520
    [  193.947544]        netlink_sendmsg+0x2fd/0x3f0
    [  193.951942]        sock_sendmsg+0x38/0x50
    [  193.955899]        ___sys_sendmsg+0x2ba/0x2d0
    [  193.960205]        __x64_sys_sendmsg+0xad/0x100
    [  193.964687]        do_syscall_64+0x5a/0x460
    [  193.968823]        entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: 7e2556e4 ("bonding: avoid lockdep confusion in bond_get_stats()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As Naresh reported, test_stacktrace_build_id() causes panic on i386 and
arm32 systems. This is caused by page_address() returns NULL in certain
cases.

This patch fixes this error by using kmap_atomic/kunmap_atomic instead
of page_address.

Fixes: 615755a7 (" bpf: extend stackmap to save binary_build_id+offset instead of address")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

When test_tcpbpf_user runs it complains that it can't find files
tcp_server.py and tcp_client.py.

Rework so that tcp_server.py and tcp_client.py gets installed, added them
to the variable TEST_PROGS_EXTENDED.

Fixes: d6d4f60c ("bpf: add selftest for tcpbpf")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Use optind as index for argv instead of a hardcoded value.
When the program has options this leads to improper parameter handling.

Fixes: dc378a1a ("samples: bpf: get ifindex from ifname")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

We build test_libbpf with CXX to make sure linking against C++ works.

$ make -s -C tools/lib/bpf
$ git status -sb
? tools/lib/bpf/test_libbpf
$ make -s -C tools/testing/selftests/bpf
$ git status -sb
? tools/lib/bpf/test_libbpf
? tools/testing/selftests/bpf/test_libbpf

Fixes: 8c4905b9 ("libbpf: make sure bpf headers are c++ include-able")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch makes sure the flow label in the IPv6 header
forged in ipv6_local_error() is initialized.

BUG: KMSAN: kernel-infoleak in _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
CPU: 1 PID: 24675 Comm: syz-executor1 Not tainted 4.20.0-rc7+ #4
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x173/0x1d0 lib/dump_stack.c:113
 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613
 kmsan_internal_check_memory+0x455/0xb00 mm/kmsan/kmsan.c:675
 kmsan_copy_to_user+0xab/0xc0 mm/kmsan/kmsan_hooks.c:601
 _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
 copy_to_user include/linux/uaccess.h:177 [inline]
 move_addr_to_user+0x2e9/0x4f0 net/socket.c:227
 ___sys_recvmsg+0x5d7/0x1140 net/socket.c:2284
 __sys_recvmsg net/socket.c:2327 [inline]
 __do_sys_recvmsg net/socket.c:2337 [inline]
 __se_sys_recvmsg+0x2fa/0x450 net/socket.c:2334
 __x64_sys_recvmsg+0x4a/0x70 net/socket.c:2334
 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x457ec9
Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f8750c06c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002f
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457ec9
RDX: 0000000000002000 RSI: 0000000020000400 RDI: 0000000000000005
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f8750c076d4
R13: 00000000004c4a60 R14: 00000000004d8140 R15: 00000000ffffffff

Uninit was stored to memory at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:204 [inline]
 kmsan_save_stack mm/kmsan/kmsan.c:219 [inline]
 kmsan_internal_chain_origin+0x134/0x230 mm/kmsan/kmsan.c:439
 __msan_chain_origin+0x70/0xe0 mm/kmsan/kmsan_instr.c:200
 ipv6_recv_error+0x1e3f/0x1eb0 net/ipv6/datagram.c:475
 udpv6_recvmsg+0x398/0x2ab0 net/ipv6/udp.c:335
 inet_recvmsg+0x4fb/0x600 net/ipv4/af_inet.c:830
 sock_recvmsg_nosec net/socket.c:794 [inline]
 sock_recvmsg+0x1d1/0x230 net/socket.c:801
 ___sys_recvmsg+0x4d5/0x1140 net/socket.c:2278
 __sys_recvmsg net/socket.c:2327 [inline]
 __do_sys_recvmsg net/socket.c:2337 [inline]
 __se_sys_recvmsg+0x2fa/0x450 net/socket.c:2334
 __x64_sys_recvmsg+0x4a/0x70 net/socket.c:2334
 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:204 [inline]
 kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:158
 kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176
 kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185
 slab_post_alloc_hook mm/slab.h:446 [inline]
 slab_alloc_node mm/slub.c:2759 [inline]
 __kmalloc_node_track_caller+0xe18/0x1030 mm/slub.c:4383
 __kmalloc_reserve net/core/skbuff.c:137 [inline]
 __alloc_skb+0x309/0xa20 net/core/skbuff.c:205
 alloc_skb include/linux/skbuff.h:998 [inline]
 ipv6_local_error+0x1a7/0x9e0 net/ipv6/datagram.c:334
 __ip6_append_data+0x129f/0x4fd0 net/ipv6/ip6_output.c:1311
 ip6_make_skb+0x6cc/0xcf0 net/ipv6/ip6_output.c:1775
 udpv6_sendmsg+0x3f8e/0x45d0 net/ipv6/udp.c:1384
 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg net/socket.c:631 [inline]
 __sys_sendto+0x8c4/0xac0 net/socket.c:1788
 __do_sys_sendto net/socket.c:1800 [inline]
 __se_sys_sendto+0x107/0x130 net/socket.c:1796
 __x64_sys_sendto+0x6e/0x90 net/socket.c:1796
 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7

Bytes 4-7 of 28 are uninitialized
Memory access of size 28 starts at ffff8881937bfce0
Data copied to user address 0000000020000000
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes false-positive kmemleak reports about leaked neighbour entries:

unreferenced object 0xffff8885c6e4d0a8 (size 1024):
  comm "softirq", pid 0, jiffies 4294922664 (age 167640.804s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 20 2c f3 83 ff ff ff ff  ........ ,......
    08 c0 ef 5f 84 88 ff ff 01 8c 7d 02 01 00 00 00  ..._......}.....
  backtrace:
    [<00000000748509fe>] ip6_finish_output2+0x887/0x1e40
    [<0000000036d7a0d8>] ip6_output+0x1ba/0x600
    [<0000000027ea7dba>] ip6_send_skb+0x92/0x2f0
    [<00000000d6e2111d>] udp_v6_send_skb.isra.24+0x680/0x15e0
    [<000000000668a8be>] udpv6_sendmsg+0x18c9/0x27a0
    [<000000004bd5fa90>] sock_sendmsg+0xb3/0xf0
    [<000000008227b29f>] ___sys_sendmsg+0x745/0x8f0
    [<000000008698009d>] __sys_sendmsg+0xde/0x170
    [<00000000889dacf1>] do_syscall_64+0x9b/0x400
    [<0000000081cdb353>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
    [<000000005767ed39>] 0xffffffffffffffff
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are some lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are handful of lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 2efd4fca ("ip: in cmsg IP(V6)_ORIGDSTADDR call
pskb_may_pull") avoided a read beyond the end of the skb linear
segment by calling pskb_may_pull.

That function can trigger a BUG_ON in pskb_expand_head if the skb is
shared, which it is when when peeking. It can also return ENOMEM.

Avoid both by switching to safer skb_header_pointer.

Fixes: 2efd4fca ("ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull")
Reported-by: syzbot <syzkaller@googlegroups.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BUG: unable to handle kernel NULL pointer dereference at 00000000000000d1
Call Trace:
 ? napi_gro_frags+0xa7/0x2c0
 tun_get_user+0xb50/0xf20
 tun_chr_write_iter+0x53/0x70
 new_sync_write+0xff/0x160
 vfs_write+0x191/0x1e0
 __x64_sys_write+0x5e/0xd0
 do_syscall_64+0x47/0xf0
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

I think there is a subtle race between sending a packet via tap and
attaching it:

CPU0:                    CPU1:
tun_chr_ioctl(TUNSETIFF)
  tun_set_iff
    tun_attach
      rcu_assign_pointer(tfile->tun, tun);
                         tun_fops->write_iter()
                           tun_chr_write_iter
                             tun_napi_alloc_frags
                               napi_get_frags
                                 napi->skb = napi_alloc_skb
      tun_napi_init
        netif_napi_add
          napi->skb = NULL
                              napi->skb is NULL here
                              napi_gro_frags
                                napi_frags_skb
				  skb = napi->skb
				  skb_reset_mac_header(skb)
				  panic()

Move rcu_assign_pointer(tfile->tun) and rcu_assign_pointer(tun->tfiles) to
be the last thing we do in tun_attach(); this should guarantee that when we
call tun_get() we always get an initialized object.

v2 changes:
* remove extra napi_mutex locks/unlocks for napi operations
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 90e33d45 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing BPF TCP initial congestion window (TCP_BPF_IW) does not
to work on (active) Fast Open sender. This is because it changes the
(initial) window only if data_segs_out is zero -- but data_segs_out
is also incremented on SYN-data.  This patch fixes the issue by
proerly accounting for SYN-data additionally.

Fixes: fc747810 ("bpf: Adds support for setting initial cwnd")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

'dev' is non NULL when the addr_len check triggers so it must goto a label
that does the dev_put otherwise dev will have a leaked refcount.

This bug causes the ib_ipoib module to become unloadable when using
systemd-network as it triggers this check on InfiniBand links.

Fixes: 99137b78 ("packet: validate address length")
Reported-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2019-01-08

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix BSD'ism in sendmsg(2) to rewrite unspecified IPv6 dst for
   unconnected UDP sockets with [::1] _after_ cgroup BPF invocation,
   from Andrey.

2) Follow-up fix to the speculation fix where we need to reject a
   corner case for sanitation when ptr and scalars are mixed in the
   same alu op. Also, some unrelated minor doc fixes, from Daniel.

3) Fix BPF kselftest's incorrect uses of create_and_get_cgroup()
   by not assuming fd of zero value to be the result of an error
   case, from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a VLAN on a bridge port, delete it and make sure the PVID VLAN is
not affected.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a VLAN is deleted from a bridge port we should not change the PVID
unless the deleted VLAN is the PVID.

Fixes: fe9ccc78 ("mlxsw: spectrum_switchdev: Don't batch VLAN operations")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running the test on the Spectrum ASIC the generated packets are
counted on the ingress filter and injected back to the pipeline because
of the 'pass' action. The router block then drops the packets due to
checksum error, as the test generates packets with zero checksum.

When running the test on an emulator that is not as strict about
checksum errors the test fails since packets are counted twice. Once by
the emulated ASIC on its ingress filter and again by the kernel as the
emulator does not perform checksum validation and allows the packets to
be trapped by a matching host route.

Fix this by changing the action to 'drop', which will prevent the packet
from continuing further in the pipeline to the router block.

For veth pairs this change is essentially a NOP given packets are only
processed once (by the kernel).

Fixes: a0b61f3d ("selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When adding / deleting VLANs to / from a bridge port, the bridge driver
first tries to propagate the information via switchdev and falls back to
the 8021q driver in case the underlying driver does not support
switchdev. This can result in a memory leak [1] when VXLAN and mlxsw
ports are enslaved to the bridge:

$ ip link set dev vxlan0 master br0
# No mlxsw ports are enslaved to 'br0', so mlxsw ignores the switchdev
# notification and the bridge driver adds the VLAN on 'vxlan0' via the
# 8021q driver
$ bridge vlan add vid 10 dev vxlan0 pvid untagged
# mlxsw port is enslaved to the bridge
$ ip link set dev swp1 master br0
# mlxsw processes the switchdev notification and the 8021q driver is
# skipped
$ bridge vlan del vid 10 dev vxlan0

This results in 'struct vlan_info' and 'struct vlan_vid_info' being
leaked, as they were allocated by the 8021q driver during VLAN addition,
but never freed as the 8021q driver was skipped during deletion.

Fix this by introducing a new VLAN private flag that indicates whether
the VLAN was added on the port by switchdev or the 8021q driver. If the
VLAN was added by the 8021q driver, then we make sure to delete it via
the 8021q driver as well.

[1]
unreferenced object 0xffff88822d20b1e8 (size 256):
  comm "bridge", pid 2532, jiffies 4295216998 (age 1188.830s)
  hex dump (first 32 bytes):
    e0 42 97 ce 81 88 ff ff 00 00 00 00 00 00 00 00  .B..............
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
    [<00000000e0178b02>] vlan_vid_add+0x661/0x920
    [<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
    [<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
    [<000000003535392c>] br_vlan_info+0x132/0x410
    [<00000000aedaa9dc>] br_afspec+0x75c/0x870
    [<00000000f5716133>] br_setlink+0x3dc/0x6d0
    [<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
    [<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
    [<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
    [<000000008be8d614>] rtnetlink_rcv+0x21/0x30
    [<000000009ab2ca25>] netlink_unicast+0x52f/0x740
    [<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
    [<000000005d1e2050>] sock_sendmsg+0xbe/0x120
    [<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
    [<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270
unreferenced object 0xffff888227454308 (size 32):
  comm "bridge", pid 2532, jiffies 4295216998 (age 1188.882s)
  hex dump (first 32 bytes):
    88 b2 20 2d 82 88 ff ff 88 b2 20 2d 82 88 ff ff  .. -...... -....
    81 00 0a 00 01 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
    [<0000000018050631>] vlan_vid_add+0x3e6/0x920
    [<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
    [<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
    [<000000003535392c>] br_vlan_info+0x132/0x410
    [<00000000aedaa9dc>] br_afspec+0x75c/0x870
    [<00000000f5716133>] br_setlink+0x3dc/0x6d0
    [<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
    [<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
    [<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
    [<000000008be8d614>] rtnetlink_rcv+0x21/0x30
    [<000000009ab2ca25>] netlink_unicast+0x52f/0x740
    [<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
    [<000000005d1e2050>] sock_sendmsg+0xbe/0x120
    [<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
    [<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270

Fixes: d70e42b2 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test case for the issue fixed by previous commit. In case the
offloading of an unsupported VxLAN tunnel was triggered by adding the
mapped VLAN to a local port, then error should be returned to the user.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding a VLAN on a port can trigger the offload of a VXLAN tunnel which
is already a member in the VLAN. In case the configuration of the VXLAN
is not supported, the driver would return -EOPNOTSUPP.

This is problematic since bridge code does not interpret this as error,
but rather that it should try to setup the VLAN using the 8021q driver
instead of switchdev.

Fixes: d70e42b2 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drivers are not supposed to return errors in switchdev commit phase if
they returned OK in prepare phase. Otherwise, a WARNING is emitted.
However, when the offloading of a VXLAN tunnel is triggered by the
addition of a VLAN on a local port, it is not possible to guarantee that
the commit phase will succeed without doing a lot of work.

In these cases, the artificial division between prepare and commit phase
does not make sense, so simply do the work in the prepare phase.

Fixes: d70e42b2 ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When VXLAN is a loadable module, MLXSW_SPECTRUM must not be built-in:

drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:2547: undefined
reference to `vxlan_fdb_find_uc'

Add Kconfig dependency to enforce usable configurations.

Fixes: 1231e04f ("mlxsw: spectrum_switchdev: Add support for VxLAN encapsulation")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure that lag port TX is disabled before mlxsw_sp_port_lag_leave()
is called and prevent from possible EMAD error.

Fixes: 0d65fc13 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removal of the mlxsw driver on Spectrum-2 platforms hits an ASSERT_RTNL()
in Spectrum-2 ACL Bloom filter and in ERP removal paths. This happens
because the multicast router implementation in Spectrum-2 relies on ACLs.
Taking the RTNL lock upon driver removal is useless since the driver first
removes its ports and unregisters from notifiers so concurrent writes
cannot happen at that time. The assertions were originally put as a
reminder for future work involving ERP background optimization, but having
these assertions only during addition serves this purpose as well.

Therefore remove the ASSERT_RTNL() in both places related to ERP and Bloom
filter removal.

Fixes: cf7221a4 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When writing to C-TCAM, mlxsw driver uses cregion->ops->entry_insert().
In case of C-TCAM HW insertion error, the opposite action should take
place.
Add error handling case in which the C-TCAM region entry is removed, by
calling cregion->ops->entry_remove().

Fixes: a0a777b9 ("mlxsw: spectrum_acl: Start using A-TCAM")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This soft dependency works around an issue where sometimes the genphy
driver is used instead of the dedicated PHY driver. The root cause of
the issue isn't clear yet. People reported the unloading/re-loading
module r8169 helps, and also configuring this soft dependency in
the modprobe config files. Important just seems to be that the
realtek module is loaded before r8169.

Once this has been applied preliminary fix 38af4b90 ("net: phy:
add workaround for issue where PHY driver doesn't bind to the device")
will be removed.

Fixes: f1e911d5 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>