The FPGA QP is a high-bandwidth communication channel between the host
CPU and the FPGA device. It allows performing DMA operations between
host memory and the FPGA logic via the ConnectX chip.

Add ConnectX FW commands which create and manipulate FPGA QPs.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The FPGA init and cleanup routines should be called just once per
device.
Move them to the init_once and cleanup_once routines.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

A QP in ConnectX is a concatenation of RQ and SQ which share a QP-number
and work together.
Add support for allocating and managing the work-queue buffer for a QP, in
a similar way to how SQs and RQs are already supported.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Move mlx5e_get_cqe routine to wq.h and rename it to
mlx5_cqwq_get_cqe.

This allows it to be used by other CQ users outside of the
ethernet driver code.

A later patch in this patchset will make use of it from
FPGA code for the FPGA high-speed connection.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Reserved gids are taken by the mlx5_core, report smaller GID table
size to IB core.

Set mlx5_query_roce_port's return value back to int. In case of
error, return an indication. This rolls back some of the change
in commit 50f22fd8 ("IB/mlx5: Set mlx5_query_roce_port's return value to void")

Change set_roce_addr to use gid_set function, instead of directly
sending the command.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Previously, only mlx5_ib enabled RoCE on the port, but FPGA needs it as
well.
Add support for counting number of enables, so that FPGA and IB can work
in parallel and independently.
Program the HW to enable RoCE on the first enable call, and program to
disable RoCE on the last disable call.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Reserved GIDs are entries in the GID table in use by the mlx5_core
and its submodules (e.g. FPGA, SRIOV, E-Swtich, netdev).
The entries are reserved at the high indexes of the GID table.

A mlx5 submodule may reserve a certain amount of GIDs for its own use
during the load sequence by calling mlx5_core_reserve_gids, and must
also take care to un-reserve these GIDs when it closes.
Reservation is only allowed during the load sequence and before any
interfaces (e.g. mlx5_ib or mlx5_en) are up.

After reservation, a submodule may call mlx5_core_reserved_gid_alloc/
free to allocate entries from the reserved GIDs pool.

Reserve a GID table entry for every supported FPGA QP.

A later patch in the patchset will remove them from being reported to
IB core.
Another such patch will make use of these for FPGA QPs in Innova NIC.

Added lib/mlx5.h to serve as a library for mlx5 submodlues, and to
expose only public mlx5 API, more mlx5 library files will be added in
future submissions.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In load_one, the interface flags are changed from down to up,
only after initializing the interfaces.
In unload_one, the flags are changed from up to down before the
interface cleanup.

Change the cleanup order to be opposite to initialization order.

This fixes flag consistency between init and cleanup.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Trivial fix to spelling mistake in en_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Matthias Schiffer says:

====================
net: add netlink_ext_ack support to rtnl_link_ops

Same changes as http://patchwork.ozlabs.org/patch/780351/ , split into
separate patches for each rtnl_link_ops field as requested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case the MACB is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2017-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.13

New features and bug fixes to quite a few different drivers, but
nothing really special standing out.

What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:

https://lkml.org/lkml/2006/1/5/671

Major changes:

wil6210

* add low level RF sector interface via nl80211 vendor commands

* add module parameter ftm_mode to load separate firmware for factory
  testing

* support devices with different PCIe bar size

* add support for PCIe D3hot in system suspend

* remove ioctl interface which should not be in a wireless driver

ath10k

* go back to using dma_alloc_coherent() for firmware scratch memory

* add per chain RSSI reporting

brcmfmac

* add support multi-scheduled scan

* add scheduled scan support for specified BSSIDs

* add support for brcm43430 revision 0

wlcore

* add wil1285 compatible

rsi

* add RS9113 USB support

iwlwifi

* FW API documentation improvements (for tools and htmldoc)

* continuing work for the new A000 family

* bump the maximum supported FW API to 31

* improve the differentiation between 8000, 9000 and A000 families
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
sctp: RFC 4960 Errata fixes

This patchset contains fixes for 4 Errata topics from
https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01
Namely, sections:
 3.12. Order of Adjustments of partial_bytes_acked and cwnd
 3.22. Increase of partial_bytes_acked in Congestion Avoidance
 3.26. CWND Increase in Congestion Avoidance Phase
 3.27. Refresh of cwnd and ssthresh after Idle Period

Tests performed with netperf using net namespaces, with drop rates at
0%, 0.5% and 1% by netem, IPv4 and IPv6, 10 runs for each combination.
I couldn't spot differences on the stats. With and without these patches
the results vary in a similar way in terms of throughput and
retransmissions.

Tests with 20ms delay and 20ms delay + drops at 0.5% and 1% also had
results in a similar way, no noticeable difference.

Looking at cwnd, it was possible to notice slightly lower values being
used while still sustaining same throughput profile.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 4960 Errata 3.27 identifies that ssthresh should be adjusted to cwnd
because otherwise it could cause the transport to lock into congestion
avoidance phase specially if ssthresh was previously reduced by some
packet drop, leading to poor performance.

The Errata says to adjust ssthresh to cwnd only once, though the same
goal is achieved by updating it every time we update cwnd too. The
caveat is that we could take longer to get back up to speed but that
should be compensated by the fact that we don't adjust on RTO basis (as
RFC says) but based on Heartbeats, which are usually way longer.

See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.27Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC4960 Errata 3.26 identified that at the same time RFC4960 states that
cwnd should never grow more than 1*MTU per RTT, Section 7.2.2 was
underspecified and as described could allow increasing cwnd more than
that.

This patch updates it so partial_bytes_acked is maxed to cwnd if
flight_size doesn't reach cwnd, protecting it from such case.

See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.26Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As per RFC4960 Errata 3.22, this condition is not needed anymore as it
could cause the partial_bytes_acked to not consider the TSNs acked in
the Gap Ack Blocks although they were received by the peer successfully.

This patch thus drops the check for new Cumulative TSN Ack Point,
leaving just the flight_size < cwnd one.

See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.22Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC4960 Errata 3.12 says RFC4960 is unclear about the order of
adjustments applied to partial_bytes_acked and cwnd in the congestion
avoidance phase, and that the actual order should be:
partial_bytes_acked is reset to (partial_bytes_acked - cwnd). Next, cwnd
is increased by MTU.

We were first increasing cwnd, and then subtracting the new value pba,
which leads to a different result as pba is smaller than what it should
and could cause cwnd to not grow as much.

See-also: https://tools.ietf.org/html/draft-ietf-tsvwg-rfc4960-errata-01#section-3.12Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like commit f663dd9a ("net: core: explicitly select a txq before doing l2 forwarding")
has removed the need for this dedicated xmit function [it even explicitly
states so in its commit log message] but it hasn't removed the definition
of the ndo.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
CC: Jason Wang <jasowang@redhat.com>
CC: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Timur Tabi says:

====================
net: qcom/emac: various minor improvements

A collection of minor fixes and features to the Qualcomm Technologies
EMAC network driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On emulation systems, the EMAC's internal PHY ("SGMII") is not present,
but is not needed for network functionality.  So just display a warning
message and ignore the SGMII.
Tested-by: Philip Elcan <pelcan@codeaurora.org>
Tested-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On ACPI systems, the driver depends on firmware pre-initializing the
EMAC because we don't have access to the clocks, and the EMAC has specific
clock programming requirements.  Therefore, we don't want to reset the
EMAC while we are completing the initialization.
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The shutdown function halts all DMA and interrupts, so that all
operations are discontinued when the system shuts down, e.g. via
kexec or a forced reboot.
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify that the caller-provided sockaddr structure is large enough to
contain the sa_family field, before accessing it in bind() and connect()
handlers of the AF_IUCV socket. Since neither syscall enforces a minimum
size of the corresponding memory region, very short sockaddrs (zero or
one byte long) result in operating on uninitialized memory while
referencing .sa_family.

Fixes: 52a82e23 ("af_iucv: Validate socket address length in iucv_sock_bind()")
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com>
[jwi: removed unneeded null-check for addr]
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use proper endianness conversion for an skb protocol assignment. Given
that IUCV is only available on big endian systems (s390), this simply
avoids an endianness warning reported by sparse.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We're accidentally returning the wrong variable.  "cmode" is
uninitialized at this point so it causes a static checker warning.

Fixes: 6335e9f2 ("net: dsa: mv88e6xxx: mv88e6390X SERDES support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
nfp: add flower app with representors

this series adds a flower app to the NFP driver.
It initialises four types of netdevs:

* PF netdev - lower-device for communication of packets to device
* PF representor netdev
* VF representor netdevs
* Phys port representor netdevs

The PF netdev acts as a lower-device which sends and receives packets to
and from the firmware. The representors act as upper-devices. For TX
representors attach a metadata dst to the skb which is used by the PF
netdev to prepend metadata to the packet before forwarding the firmware. On
RX the PF netdev looks up the representor based on the prepended metadata
received from the firmware and forwards the skb to the representor after
removing the metadata.

Control queues are used to send and receive control messages which are
used to communicate configuration information with the firmware. These
are in separate vNIC to the queues belonging to the PF netdev. The control
queues are not exposed to use-space via a netdev or any other means.

The first 9 patches of this series provide app-independent infrastructure
to instantiate representors and the remaining 3 patches provide an app
which uses this infrastructure.

As the name implies this app is targeted at providing offload of TC flower.
Flower offload - allowing classifiers to be attached to representor netdevs
- is intended to be provided by follow-up patches at which point it will
become the dominant feature of the app.

Minor changes since v2 noted in changelogs of individual patches.
Review of v1 and v2 of this patchset have been addressed either
through discussion on-list or changes in this patchset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialise VF and PF representors in flower app.

Based in part on work by Benjamin LaHaise, Bert van Leeuwen and
Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add app for flower offload. At this point the PF netdev and phys port
representor netdevs are initialised. Follow-up work will add support for
VF and PF representors and beyond that offloading the flower classifier.

Based in part on work by Benjamin LaHaise and Bert van Leeuwen.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for adding a new flower app - targeted at offloading
the flower classifier - provide support for control message that it will
use to communicate with the NFP.

Based in part on work by Bert van Leeuwen.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow tx/rx with metadata port id. This will be used for tx/rx of
representor netdevs acting as upper-devices while a pf netdev acts
as a lower-device.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide port rather than vNIC as parameter of nfp_net_get_mac_addr.
This is to allow this function to be used by representor netdevs where
a vNIC may have more than one physical port none of which are associated
with the vNIC.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add app-callbacks for app-specific initialisation of SRIOV.

Disabling SRIOV is brought forward in nfp_pci_remove()
so that nfp_app_sriov_disable is called while the app still exists.

This is intended to be used to implement representor netdevs for virtual
ports.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide helpers for stats and xmit on representor netdevs.

Parts based on work by Bert van Leeuwen, Benjamin LaHaise and
Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide infrastructure to create and destroy representors of a given type.

Parts based on work by Bert van Leeuwen, Benjamin LaHaise,
and Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If present map mac_stats and vf_cfg BARs. These will be used by
representor netdevs to read statistics for phys port and vf representors.

Also provide defines describing the layout of the mac_stats area.
Similar defines are already present for the cf_cfg area.

Based in part on work by Jakub Kicinski.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>