- 01 Feb, 2023 3 commits
-
-
Dmitry Torokhov authored
Switch the driver from legacy gpio API that is deprecated to the newer gpiod API that respects line polarities described in ACPI/DT. Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Link: https://lore.kernel.org/r/20230201053447.4098486-2-dmitry.torokhov@gmail.comSigned-off-by:
Stefan Schmidt <stefan@datenfreihafen.org>
-
Dmitry Torokhov authored
There are no users of platform data in the mainline tree, and new boards should use either ACPI or device tree, so let's stop supporting it. This will help with converting the driver to gpiod API. Signed-off-by:
-
Stefan Schmidt authored
This reverts commit 622bd6ea. Dmitry Torokhov points out that this conversion leaves an existing board in reset state due to not properly handled polarity. Additionally, the GPIO name inadvertenly changes from "reset-gpio" to "rstn-gpios". Revert to avoid these regressions. Follow up patches for a better conversion are applied as well. Signed-off-by:
-
- 31 Jan, 2023 1 commit
-
-
Arnd Bergmann authored
cc2520 supports both probing from static platform_data and from devicetree, but there have never been any definitions of the platform data in the mainline kernel, so it's safe to assume that only the DT path is used. After folding cc2520_platform_data into the driver itself, the GPIO handling can be simplified by moving to the modern gpiod interface. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20230126161658.2983292-1-arnd@kernel.orgSigned-off-by:
-
- 30 Jan, 2023 1 commit
-
-
Miquel Raynal authored
When compiling scan.c with C=1, Sparse complains with: sparse: expected unsigned short [usertype] val sparse: got restricted __le16 [usertype] pan_id sparse: sparse: cast from restricted __le16 sparse: expected unsigned long long [usertype] val sparse: got restricted __le64 [usertype] extended_addr sparse: sparse: cast from restricted __le64 The tool is right, both pan_id and extended_addr already are rightfully defined as being __le16 and __le64 on both sides of the operations and do not require extra endianness handling. Fixes: 3accf476 ("mac802154: Handle basic beaconing") Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20230130154306.114265-1-miquel.raynal@bootlin.comSigned-off-by:
-
- 28 Jan, 2023 3 commits
-
-
Arnd Bergmann authored
There are no remaining in-tree users of the platform_data, so this driver can be converted to using the simpler gpiod interfaces. Any out-of-tree users that rely on the platform data can provide the data using the device_property and gpio_lookup interfaces instead. Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Miquel Raynal authored
Implement the core hooks in order to provide the softMAC layer support for sending beacons. Coordinators may be requested to send beacons in a beacon enabled PAN in order for the other devices around to self discover the available PANs automatically. Changing the channels is prohibited while a beacon operation is ongoing. The implementation uses a workqueue triggered at a certain interval depending on the symbol duration for the current channel and the interval order provided. Sending beacons in response to a BEACON_REQ frame (ie. answering active scans) is not yet supported. This initial patchset has no security support (llsec). Co-developed-by:
David Girault <david.girault@qorvo.com> Signed-off-by:
Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20230125102923.135465-3-miquel.raynal@bootlin.comSigned-off-by:
-
Miquel Raynal authored
Parse user requests for sending beacons, start sending beacons at a regular pace. If needed, the pace can be updated with a new request. The process can also be interrupted at any moment. The page and channel must be changed beforehands if needed. Interval orders above 14 are reserved to tell a device it must answer BEACON_REQ coming from another device as part of an active scan procedure and this is not yet supported. A netlink "beacon request" structure is created to list the requirements. Mac layers may now implement the ->send_beacons() and ->stop_beacons() hooks. Co-developed-by:
-
- 03 Jan, 2023 6 commits
-
-
Miquel Raynal authored
Implement the core hooks in order to provide the softMAC layer support for passive scans. Scans are requested by the user and can be aborted. Changing channels manually is prohibited during scans. The implementation uses a workqueue triggered at a certain interval depending on the symbol duration for the current channel and the duration order provided. More advanced drivers with internal scheduling capabilities might require additional care but there is none mainline yet. Received beacons during a passive scan are processed in a work queue and their result forwarded to the upper layer. Active scanning is not supported yet. Co-developed-by:
-
Miquel Raynal authored
These have the exact same behavior as before, except they expect the rtnl to be already taken (and will complain otherwise). This allows performing MLME transmissions from different contexts. Signed-off-by:
-
Miquel Raynal authored
The scan logic will bypass the whole ->set_channel() logic from the top by calling the driver hook to just switch between channels when required. We can no longer rely on the "current" page/channel settings to set the right symbol duration. Let's add these as new parameters to allow providing the page/channel couple that we want. There is no functional change. Signed-off-by:
-
Miquel Raynal authored
This helper for now only checks if the page member and channel member are valid (in the specification range) and supported (by checking the device capabilities). Soon two new parameters will be introduced and having this helper will let us only modify its content rather than modifying the logic everywhere else in the subsystem. There is not functional change. Signed-off-by:
-
Miquel Raynal authored
This definition will be used when adding support for scanning and defines the content of a beacon frame header as in the 802.15.4 specification. Signed-off-by:
-
Miquel Raynal authored
The ieee802154 layer should be able to scan a set of channels in order to look for beacons advertizing PANs. Supporting this involves adding two user commands: triggering scans and aborting scans. The user should also be notified when a new beacon is received and also upon scan termination. A scan request structure is created to list the requirements and to be accessed asynchronously when changing channels or receiving beacons. Mac layers may now implement the ->trigger_scan() and ->abort_scan() hooks. Co-developed-by:
-
- 08 Dec, 2022 26 commits
-
-
Jakub Kicinski authored
Roger Quadros says: ==================== net: ethernet: ti: am65-cpsw: Fix set channel operation This contains a critical bug fix for the recently merged suspend/resume support [1] that broke set channel operation. (ethtool -L eth0 tx <n>) As there were 2 dependent patches on top of the offending commit [1] first revert them and then apply them back after the correct fix. [1] fd23df72 ("net: ethernet: ti: am65-cpsw: Add suspend/resume support") ==================== Link: https://lore.kernel.org/r/20221206094419.19478-1-rogerq@kernel.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Roger Quadros authored
On low power during system suspend the ALE table context is lost. Save the ALE context before suspend and restore it after resume. Signed-off-by:
Roger Quadros <rogerq@kernel.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Roger Quadros authored
During suspend resume the context of PORT_VLAN_REG is lost so save it during suspend and restore it during resume for host port and slave ports. Signed-off-by:
-
Roger Quadros authored
Add PM handlers for System suspend/resume. As DMA driver doesn't yet support suspend/resume we free up the DMA channels at suspend and acquire and initialize them at resume. In this revised approach we do not free the TX/RX IRQs at am65_cpsw_nuss_common_stop() as it causes problems. We will now free them only on .suspend() as we need to release the DMA channels (as DMA looses context) and re-acquiring them on .resume() may not necessarily give us the same IRQs. To make this easier: - introduce am65_cpsw_nuss_remove_rx_chns() which is similar to am65_cpsw_nuss_remove_tx_chns(). These will be invoked in pm.suspend() to release the DMA channels and free up the IRQs. - move napi_add() and request_irq() calls to am65_cpsw_nuss_init_rx/tx_chns() so we can invoke them in pm.resume() to acquire the DMA channels and IRQs. As CPTS looses contect during suspend/resume, invoke the necessary CPTS suspend/resume helpers. ALE_CLEAR command is issued in cpsw_ale_start() so no need to issue it before the call to cpsw_ale_start(). Signed-off-by:
-
Roger Quadros authored
This reverts commit fd23df72. This commit broke set channel operation. Revert this and implement it with a different approach in a separate patch. Signed-off-by:
-
Roger Quadros authored
This reverts commit 643cf0e3. This is to make it easier to revert the offending commit fd23df72 ("net: ethernet: ti: am65-cpsw: Add suspend/resume support") Signed-off-by:
-
Roger Quadros authored
This reverts commit 1af3cb37. This is to make it easier to revert the offending commit fd23df72 ("net: ethernet: ti: am65-cpsw: Add suspend/resume support") Signed-off-by:
-
Jakub Kicinski authored
Shay Drory says: ==================== devlink: Add port function attribute to enable/disable Roce and migratable This series is a complete rewrite of the series "devlink: Add port function attribute to enable/disable roce" link: https://lore.kernel.org/netdev/20221102163954.279266-1-danielj@nvidia.com/ Currently mlx5 PCI VF and SF are enabled by default for RoCE functionality. And mlx5 PCI VF is disable by dafault for migratable functionality. Currently a user does not have the ability to disable RoCE for a PCI VF/SF device before such device is enumerated by the driver. User is also incapable to do such setting from smartnic scenario for a VF from the smartnic. Current 'enable_roce' device knob is limited to do setting only at driverinit time. By this time device is already created and firmware has already allocated necessary system memory for supporting RoCE. Also, Currently a user does not have the ability to enable migratable for a PCI VF. The above are a hyper visor level control, to set the functionality of devices passed through to guests. This is achieved by extending existing 'port function' object to control capabilities of a function. This enables users to control capability of the device before enumeration. Examples when user prefers to disable RoCE for a VF when using switchdev mode: $ devlink port show pci/0000:06:00.0/1 pci/0000:06:00.0/1: type eth netdev pf0vf0 flavour pcivf controller 0 pfnum 0 vfnum 0 external false splittable false function: hw_addr 00:00:00:00:00:00 roce enable $ devlink port function set pci/0000:06:00.0/1 roce disable $ devlink port show pci/0000:06:00.0/1 pci/0000:06:00.0/1: type eth netdev pf0vf0 flavour pcivf controller 0 pfnum 0 vfnum 0 external false splittable false function: hw_addr 00:00:00:00:00:00 roce disable FAQs: ----- 1. What does roce enable/disable do? Ans: It disables RoCE capability of the function before its enumerated, so when driver reads the capability from the device firmware, it is disabled. At this point RDMA stack will not be able to create UD, QP1, RC, XRC type of QPs. When RoCE is disabled, the GID table of all ports of the device is disabled in the device and software stack. 2. How is the roce 'port function' option different from existing devlink param? Ans: RoCE attribute at the port function level disables the RoCE capability at the specific function level; while enable_roce only does at the software level. 3. Why is this option for disabling only RoCE and not the whole RDMA device? Ans: Because user still wants to use the RDMA device for non RoCE commands in more memory efficient way. ==================== Link: https://lore.kernel.org/r/20221206185119.380138-1-shayd@nvidia.comSigned-off-by:
-
Shay Drory authored
Implement devlink port function commands to enable / disable migratable. This is used to control the migratable capability of the device. Signed-off-by:
Shay Drory <shayd@nvidia.com> Reviewed-by:
Mark Bloch <mbloch@nvidia.com> Acked-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
-
Shay Drory authored
Expose port function commands to enable / disable migratable capability, this is used to set the port function as migratable. Live migration is the process of transferring a live virtual machine from one physical host to another without disrupting its normal operation. In order for a VM to be able to perform LM, all the VM components must be able to perform migration. e.g.: to be migratable. In order for VF to be migratable, VF must be bound to VFIO driver with migration support. When migratable capability is enabled for a function of the port, the device is making the necessary preparations for the function to be migratable, which might include disabling features which cannot be migrated. Example of LM with migratable function configuration: Set migratable of the VF's port function. $ devlink port show pci/0000:06:00.0/2 pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1 function: hw_addr 00:00:00:00:00:00 migratable disable $ devlink port function set pci/0000:06:00.0/2 migratable enable $ devlink port show pci/0000:06:00.0/2 pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1 function: hw_addr 00:00:00:00:00:00 migratable enable Bind VF to VFIO driver with migration support: $ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/unbind $ echo mlx5_vfio_pci > /sys/bus/pci/devices/0000:08:00.0/driver_override $ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/bind Attach VF to the VM. Start the VM. Perform LM. Signed-off-by:Jiri Pirko <jiri@nvidia.com> Acked-by:
Shannon Nelson <shannon.nelson@amd.com> Signed-off-by:
-
Yishai Hadas authored
Implement devlink port function commands to enable / disable RoCE. This is used to control the RoCE device capabilities. This patch implement infrastructure which will be used by downstream patches that will add additional capabilities. Signed-off-by:
Yishai Hadas <yishaih@nvidia.com> Signed-off-by:
Daniel Jurgens <danielj@nvidia.com> Signed-off-by:
Parav Pandit <parav@nvidia.com> Reviewed-by:
-
Shay Drory authored
Downstream patch requires to get other function GENERAL2 caps while mlx5_vport_get_other_func_cap() gets only one type of caps (general). Rename it to represent this and introduce a generic implementation of mlx5_vport_get_other_func_cap(). Signed-off-by:
-
Shay Drory authored
Expose port function commands to enable / disable RoCE, this is used to control the port RoCE device capabilities. When RoCE is disabled for a function of the port, function cannot create any RoCE specific resources (e.g GID table). It also saves system memory utilization. For example disabling RoCE enable a VF/SF saves 1 Mbytes of system memory per function. Example of a PCI VF port which supports function configuration: Set RoCE of the VF's port function. $ devlink port show pci/0000:06:00.0/2 pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1 function: hw_addr 00:00:00:00:00:00 roce enable $ devlink port function set pci/0000:06:00.0/2 roce disable $ devlink port show pci/0000:06:00.0/2 pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1 function: hw_addr 00:00:00:00:00:00 roce disable Signed-off-by: -
Shay Drory authored
devlink port function hw_addr attr documentation is in mlx5 specific file while there is nothing mlx5 specific about it. Move it to devlink-port.rst. Signed-off-by:
-
Shay Drory authored
In order to avoid partial request processing, validate the request before processing it. Signed-off-by:
-
Yishai Hadas authored
Introduce IFC related capabilities to enable setting VF to be able to perform live migration. e.g.: to be migratable. Signed-off-by:
-
Jakub Kicinski authored
Ido Schimmel says: ==================== bridge: mcast: Preparations for EVPN extensions This patchset was split from [1] and includes non-functional changes aimed at making it easier to add additional netlink attributes later on. Future extensions are available here [2]. The idea behind these patches is to create an MDB configuration structure into which netlink messages are parsed into. The structure is then passed in the entry creation / deletion call chain instead of passing the netlink attributes themselves. The same pattern is used by other rtnetlink objects such as routes and nexthops. I initially tried to extend the current code, but it proved to be too difficult, which is why I decided to refactor it to the extensible and familiar pattern used by other rtnetlink objects. Tested using existing selftests and using a new selftest that will be submitted together with the planned extensions. [1] https://lore.kernel.org/netdev/20221018120420.561846-1-idosch@nvidia.com/ [2] https://github.com/idosch/linux/commits/submit/mdb_v1 ==================== Link: https://lore.kernel.org/r/20221206105809.363767-1-idosch@nvidia.comSigned-off-by:
-
Ido Schimmel authored
The 'group' argument is not modified, so mark it as 'const'. It will allow us to constify arguments of the callers of this function in future patches. Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Acked-by:
Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by:
-
Ido Schimmel authored
Drop the first three arguments and instead extract them from the MDB configuration structure. Signed-off-by:
-
Ido Schimmel authored
The checks only require information parsed from the RTM_NEWMDB netlink message and do not rely on any state stored in the bridge driver. Therefore, there is no need to perform the checks in the critical section under the multicast lock. Move the checks out of the critical section. Signed-off-by:
-
Ido Schimmel authored
The parsing of the netlink messages and the validity checks are now performed in br_mdb_config_init() so we can remove br_mdb_parse(). This finally allows us to stop passing netlink attributes deep in the MDB control path and only use the MDB configuration structure. Signed-off-by:
-
Ido Schimmel authored
The MDB group key (i.e., {source, destination, protocol, VID}) is currently determined under the multicast lock from the netlink attributes. Instead, use the group key from the MDB configuration structure that was prepared before acquiring the lock. No functional changes intended. Signed-off-by: -
Ido Schimmel authored
As an intermediate step towards only using the new MDB configuration structure, pass it further in the control path instead of passing individual attributes. No functional changes intended. Signed-off-by:
-
Ido Schimmel authored
The MDB configuration structure (i.e., struct br_mdb_config) now includes all the necessary information from the parsed RTM_{NEW,DEL}MDB netlink messages, so use it. This will later allow us to delete the calls to br_mdb_parse() from br_mdb_add() and br_mdb_del(). No functional changes intended. Signed-off-by: -
Ido Schimmel authored
These checks are now redundant as they are performed by br_mdb_config_init() while parsing the RTM_{NEW,DEL}MDB messages. Remove them. Signed-off-by: -
Ido Schimmel authored
Netlink attributes are currently passed deep in the MDB creation call chain, making it difficult to add new attributes. In addition, some validity checks are performed under the multicast lock although they can be performed before it is ever acquired. As a first step towards solving these issues, parse the RTM_{NEW,DEL}MDB messages into a configuration structure, relieving other functions from the need to handle raw netlink attributes. Subsequent patches will convert the MDB code to use this configuration structure. This is consistent with how other rtnetlink objects are handled, such as routes and nexthops. Signed-off-by:
-
