- 31 Aug, 2021 12 commits
-
-
David S. Miller authored
Subbaraya Sundeep says: ==================== octeontx2-af: Miscellaneous fixes in npc This patchset consists of consolidated fixes in rvu_npc file. Two of the patches prevent infinite loop which can happen in corner cases. One patch is for fixing static code analyzer reported issues. And the last patch is a minor change in npc protocol checker hardware block to report ipv4 checksum errors as a known error codes. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Sunil Goutham authored
With current config, for packets with IPv4 checksum errors, errorcode is being set to UNKNOWN. Hence added a separate errorcodes for outer and inner IPv4 checksum and changed NPC configuration accordingly. Also turn on L2 multicast address check in NPC protocol check block. Fixes: 6b3321ba ("octeontx2-af: Enable packet length and csum validation") Signed-off-by:
Sunil Goutham <sgoutham@marvell.com> Signed-off-by:
Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by:
-
Subbaraya Sundeep authored
This patch fixes the static code analyzer reported issues in rvu_npc.c. The reported errors are different sizes of operands in bitops and returning uninitialized values. Fixes: 651cd265 ("octeontx2-af: MCAM entry installation support") Signed-off-by:
-
Subbaraya Sundeep authored
In npc_update_vf_flow_entry function the loop cursor 'index' is being changed inside the loop causing the loop to spin forever. This in turn hogs the kworker thread forever and no other mbox message is processed by AF driver after that. Fix this by using another variable in the loop. Fixes: 55307fcb ("octeontx2-af: Add mbox messages to install and delete MCAM rules") Signed-off-by:
-
Subbaraya Sundeep authored
When the given counter does not belong to the entry then code ends up in infinite loop because the loop cursor, entry is not getting updated further. This patch fixes that by updating entry for every iteration. Fixes: a958dd59 ("octeontx2-af: Map or unmap NPC MCAM entry and counter") Signed-off-by:
-
Eric Dumazet authored
syzbot was able to trigger NULL deref in unix_dgram_connect() [1] This happens in if (unix_peer(sk)) sk->sk_state = other->sk_state = TCP_ESTABLISHED; // crash because @other is NULL Because locks have been dropped, unix_peer() might be non NULL, while @other is NULL (AF_UNSPEC case) We need to move code around, so that we no longer access unix_peer() and sk_state while locks have been released. [1] general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] CPU: 0 PID: 10341 Comm: syz-executor239 Not tainted 5.14.0-rc7-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:unix_dgram_connect+0x32a/0xc60 net/unix/af_unix.c:1226 Code: 00 00 45 31 ed 49 83 bc 24 f8 05 00 00 00 74 69 e8 eb 5b a6 f9 48 8d 7d 12 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02 48 89 fa 83 e2 07 38 d0 7f 08 84 c0 0f 85 e0 07 00 00 RSP: 0018:ffffc9000a89fcd8 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000004 RCX: 0000000000000000 RDX: 0000000000000002 RSI: ffffffff87cf4ef5 RDI: 0000000000000012 RBP: 0000000000000000 R08: 0000000000000000 R09: ffff88802e1917c3 R10: ffffffff87cf4eba R11: 0000000000000001 R12: ffff88802e191740 R13: 0000000000000000 R14: ffff88802e191d38 R15: ffff88802e1917c0 FS: 00007f3eb0052700(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000004787d0 CR3: 0000000029c0a000 CR4: 00000000001506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: __sys_connect_file+0x155/0x1a0 net/socket.c:1890 __sys_connect+0x161/0x190 net/socket.c:1907 __do_sys_connect net/socket.c:1917 [inline] __se_sys_connect net/socket.c:1914 [inline] __x64_sys_connect+0x6f/0xb0 net/socket.c:1914 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x446a89 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 a1 15 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f3eb0052208 EFLAGS: 00000246 ORIG_RAX: 000000000000002a RAX: ffffffffffffffda RBX: 00000000004cc4d8 RCX: 0000000000446a89 RDX: 000000000000006e RSI: 0000000020000180 RDI: 0000000000000003 RBP: 00000000004cc4d0 R08: 00007f3eb0052700 R09: 0000000000000000 R10: 00007f3eb0052700 R11: 0000000000000246 R12: 00000000004cc4dc R13: 00007ffd791e79cf R14: 00007f3eb0052300 R15: 0000000000022000 Modules linked in: ---[ end trace 4eb809357514968c ]--- RIP: 0010:unix_dgram_connect+0x32a/0xc60 net/unix/af_unix.c:1226 Code: 00 00 45 31 ed 49 83 bc 24 f8 05 00 00 00 74 69 e8 eb 5b a6 f9 48 8d 7d 12 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02 48 89 fa 83 e2 07 38 d0 7f 08 84 c0 0f 85 e0 07 00 00 RSP: 0018:ffffc9000a89fcd8 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000004 RCX: 0000000000000000 RDX: 0000000000000002 RSI: ffffffff87cf4ef5 RDI: 0000000000000012 RBP: 0000000000000000 R08: 0000000000000000 R09: ffff88802e1917c3 R10: ffffffff87cf4eba R11: 0000000000000001 R12: ffff88802e191740 R13: 0000000000000000 R14: ffff88802e191d38 R15: ffff88802e1917c0 FS: 00007f3eb0052700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffd791fe960 CR3: 0000000029c0a000 CR4: 00000000001506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Fixes: 83301b53 ("af_unix: Set TCP_ESTABLISHED for datagram sockets too") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Cong Wang <cong.wang@bytedance.com> Cc: Alexei Starovoitov <ast@kernel.org> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Jason Wang authored
The strlcpy should not be used because it doesn't limit the source length. As linus says, it's a completely useless function if you can't implicitly trust the source string - but that is almost always why people think they should use it! All in all the BSD function will lead some potential bugs. But the strscpy doesn't require reading memory from the src string beyond the specified "count" bytes, and since the return value is easier to error-check than strlcpy()'s. In addition, the implementation is robust to the string changing out from underneath it, unlike the current strlcpy() implementation. Thus, We prefer using strscpy instead of strlcpy. Signed-off-by:
Jason Wang <wangborong@cdjrlc.com> Signed-off-by:
-
Geetha sowjanya authored
For better performance set hardware to use NDC TX for reading packet data specified NIX_SEND_SG_S. Signed-off-by:
Geetha sowjanya <gakula@marvell.com> Signed-off-by:
-
MichelleJin authored
br_ip6_multicast_mld2_report function uses icmp6h to parse mld2_report packet. mld2r_ngrec defines mld2r_hdr.icmp6_dataun.un_data16[1] in include/net/mld.h. So, it is more compact to use mld2r rather than icmp6h. By doing printk test, it is confirmed that icmp6h->icmp6_dataun.un_data16[1] and mld2r->mld2r_ngrec are indeed equivalent. Also, sizeof(*mld2r) and sizeof(*icmp6h) are equivalent, too. Signed-off-by:
MichelleJin <shjy180909@gmail.com> Signed-off-by:
-
Stefan Wahren authored
Based on tests the QCA7000 doesn't support checksum offloading. So assume ip_summed is CHECKSUM_NONE and let the kernel take care of the checksum handling. This fixes data transfer issues in noisy environments. Reported-by:
Michael Heimpold <michael.heimpold@in-tech.com> Fixes: 291ab06e ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
-
Christophe JAILLET authored
In [1], Christoph Hellwig has proposed to remove the wrappers in include/linux/pci-dma-compat.h. Some reasons why this API should be removed have been given by Julia Lawall in [2]. A coccinelle script has been used to perform the needed transformation Only relevant parts are given below. An 'unlikely()' has been removed when calling 'dma_mapping_error()' because this function, which is inlined, already has such an annotation. @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) [1]: https://lore.kernel.org/kernel-janitors/20200421081257.GA131897@infradead.org/ [2]: https://lore.kernel.org/kernel-janitors/alpine.DEB.2.22.394.2007120902170.2424@hadrien/Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/bc6cd281eae024b26fd9c7ef6678d2d1dc9d74fd.1630150008.git.christophe.jaillet@wanadoo.frSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Xiyu Yang authored
The reference counting issue happens in one exception handling path of cbq_change_class(). When failing to get tcf_block, the function forgets to decrease the refcount of "rtab" increased by qdisc_put_rtab(), causing a refcount leak. Fix this issue by jumping to "failure" label when get tcf_block failed. Fixes: 6529eaba ("net: sched: introduce tcf block infractructure") Signed-off-by:
Xiyu Yang <xiyuyang19@fudan.edu.cn> Reviewed-by:
Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/r/1630252681-71588-1-git-send-email-xiyuyang19@fudan.edu.cnSigned-off-by:
-
- 30 Aug, 2021 28 commits
-
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextJakub Kicinski authored
Daniel Borkmann says: ==================== bpf-next 2021-08-31 We've added 116 non-merge commits during the last 17 day(s) which contain a total of 126 files changed, 6813 insertions(+), 4027 deletions(-). The main changes are: 1) Add opaque bpf_cookie to perf link which the program can read out again, to be used in libbpf-based USDT library, from Andrii Nakryiko. 2) Add bpf_task_pt_regs() helper to access userspace pt_regs, from Daniel Xu. 3) Add support for UNIX stream type sockets for BPF sockmap, from Jiang Wang. 4) Allow BPF TCP congestion control progs to call bpf_setsockopt() e.g. to switch to another congestion control algorithm during init, from Martin KaFai Lau. 5) Extend BPF iterator support for UNIX domain sockets, from Kuniyuki Iwashima. 6) Allow bpf_{set,get}sockopt() calls from setsockopt progs, from Prankur Gupta. 7) Add bpf_get_netns_cookie() helper for BPF_PROG_TYPE_{SOCK_OPS,CGROUP_SOCKOPT} progs, from Xu Liu and Stanislav Fomichev. 8) Support for __weak typed ksyms in libbpf, from Hao Luo. 9) Shrink struct cgroup_bpf by 504 bytes through refactoring, from Dave Marchevsky. 10) Fix a smatch complaint in verifier's narrow load handling, from Andrey Ignatov. 11) Fix BPF interpreter's tail call count limit, from Daniel Borkmann. 12) Big batch of improvements to BPF selftests, from Magnus Karlsson, Li Zhijian, Yucong Sun, Yonghong Song, Ilya Leoshkevich, Jussi Maki, Ilya Leoshkevich, others. 13) Another big batch to revamp XDP samples in order to give them consistent look and feel, from Kumar Kartikeya Dwivedi. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (116 commits) MAINTAINERS: Remove self from powerpc BPF JIT selftests/bpf: Fix potential unreleased lock samples: bpf: Fix uninitialized variable in xdp_redirect_cpu selftests/bpf: Reduce more flakyness in sockmap_listen bpf: Fix bpf-next builds without CONFIG_BPF_EVENTS bpf: selftests: Add dctcp fallback test bpf: selftests: Add connect_to_fd_opts to network_helpers bpf: selftests: Add sk_state to bpf_tcp_helpers.h bpf: tcp: Allow bpf-tcp-cc to call bpf_(get|set)sockopt selftests: xsk: Preface options with opt selftests: xsk: Make enums lower case selftests: xsk: Generate packets from specification selftests: xsk: Generate packet directly in umem selftests: xsk: Simplify cleanup of ifobjects selftests: xsk: Decrease sending speed selftests: xsk: Validate tx stats on tx thread selftests: xsk: Simplify packet validation in xsk tests selftests: xsk: Rename worker_* functions that are not thread entry points selftests: xsk: Disassociate umem size with packets sent selftests: xsk: Remove end-of-test packet ... ==================== Link: https://lore.kernel.org/r/20210830225618.11634-1-daniel@iogearbox.netSigned-off-by: -
Maxim Mikityanskiy authored
In HTB offload mode, qdiscs of leaf classes are grafted to netdev queues. sch_htb expects the dev_queue field of these qdiscs to point to the corresponding queues. However, qdisc creation may fail, and in that case noop_qdisc is used instead. Its dev_queue doesn't point to the right queue, so sch_htb can lose track of used netdev queues, which will cause internal inconsistencies. This commit fixes this bug by keeping track of the netdev queue inside struct htb_class. All reads of cl->leaf.q->dev_queue are replaced by the new field, the two values are synced on writes, and WARNs are added to assert equality of the two values. The driver API has changed: when TC_HTB_LEAF_DEL needs to move a queue, the driver used to pass the old and new queue IDs to sch_htb. Now that there is a new field (offload_queue) in struct htb_class that needs to be updated on this operation, the driver will pass the old class ID to sch_htb instead (it already knows the new class ID). Fixes: d03b195b ("sch_htb: Hierarchical QoS hardware offload") Signed-off-by:
Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20210826115425.1744053-1-maximmi@nvidia.comSigned-off-by:
-
Sandipan Das authored
Stepping down as I haven't had a chance to look into the powerpc BPF JIT compilers for a while. Signed-off-by:
Sandipan Das <sandipan@linux.ibm.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20210827111905.396145-1-sandipan@linux.ibm.com
-
Yajun Deng authored
Add a if statements to avoid the warning. Dan Carpenter report: The patch faf482ca: "net: ipv4: Move ip_options_fragment() out of loop" from Aug 23, 2021, leads to the following Smatch complaint: net/ipv4/ip_output.c:833 ip_do_fragment() warn: variable dereferenced before check 'iter.frag' (see line 828) Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Fixes: faf482ca ("net: ipv4: Move ip_options_fragment() out of loop") Link: https://lore.kernel.org/netdev/20210830073802.GR7722@kadam/T/#tSigned-off-by:
Yajun Deng <yajun.deng@linux.dev> Signed-off-by:
-
Dan Carpenter authored
These checks are still not strict enough. The main problem is that if "cb->type == QRTR_TYPE_NEW_SERVER" is true then "len - hdrlen" is guaranteed to be 4 but we need to be at least 16 bytes. In fact, we can reject everything smaller than sizeof(*pkt) which is 20 bytes. Also I don't like the ALIGN(size, 4). It's better to just insist that data is needs to be aligned at the start. Fixes: 0baa99ee ("net: qrtr: Allow non-immediate node routing") Signed-off-by:
-
Haimin Zhang authored
syzbot report an array-index-out-of-bounds in taprio_change index 16 is out of range for type '__u16 [16]' that's because mqprio->num_tc is lager than TC_MAX_QUEUE,so we check the return value of netdev_set_num_tc. Reported-by: syzbot+2b3e5fb6c7ef285a94f6@syzkaller.appspotmail.com Signed-off-by:
Haimin Zhang <tcs_kernel@tencent.com> Signed-off-by:
-
王贇 authored
In netlbl_cipsov4_add_std() when 'doi_def->map.std' alloc failed, we sometime observe panic: BUG: kernel NULL pointer dereference, address: ... RIP: 0010:cipso_v4_doi_free+0x3a/0x80 ... Call Trace: netlbl_cipsov4_add_std+0xf4/0x8c0 netlbl_cipsov4_add+0x13f/0x1b0 genl_family_rcv_msg_doit.isra.15+0x132/0x170 genl_rcv_msg+0x125/0x240 This is because in cipso_v4_doi_free() there is no check on 'doi_def->map.std' when doi_def->type got value 1, which is possibe, since netlbl_cipsov4_add_std() haven't initialize it before alloc 'doi_def->map.std'. This patch just add the check to prevent panic happen in similar cases. Reported-by:
Abaci <abaci@linux.alibaba.com> Signed-off-by:
Michael Wang <yun.wang@linux.alibaba.com> Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== inet: make exception handling less predictible This second round of patches is addressing Keyu Man recommendations to make linux hosts more robust against a class of brute force attacks. ==================== Signed-off-by: -
Eric Dumazet authored
Even after commit 6457378f ("ipv4: use siphash instead of Jenkins in fnhe_hashfun()"), an attacker can still use brute force to learn some secrets from a victim linux host. One way to defeat these attacks is to make the max depth of the hash table bucket a random value. Before this patch, each bucket of the hash table used to store exceptions could contain 6 items under attack. After the patch, each bucket would contains a random number of items, between 6 and 10. The attacker can no longer infer secrets. This is slightly increasing memory size used by the hash table, by 50% in average, we do not expect this to be a problem. This patch is more complex than the prior one (IPv6 equivalent), because IPv4 was reusing the oldest entry. Since we need to be able to evict more than one entry per update_or_create_fnhe() call, I had to replace fnhe_oldest() with fnhe_remove_oldest(). Also note that we will queue extra kfree_rcu() calls under stress, which hopefully wont be a too big issue. Fixes: 4895c771 ("ipv4: Add FIB nexthop exceptions.") Signed-off-by:
Keyu Man <kman001@ucr.edu> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
David Ahern <dsahern@kernel.org> Tested-by:
-
Eric Dumazet authored
Even after commit 4785305c ("ipv6: use siphash in rt6_exception_hash()"), an attacker can still use brute force to learn some secrets from a victim linux host. One way to defeat these attacks is to make the max depth of the hash table bucket a random value. Before this patch, each bucket of the hash table used to store exceptions could contain 6 items under attack. After the patch, each bucket would contains a random number of items, between 6 and 10. The attacker can no longer infer secrets. This is slightly increasing memory size used by the hash table, we do not expect this to be a problem. Following patch is dealing with the same issue in IPv4. Fixes: 35732d01 ("ipv6: introduce a hash table to store dst cache") Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter updates for net-next The following patchset contains Netfilter updates for net-next: 1) Clean up and consolidate ct ecache infrastructure by merging ct and expect notifiers, from Florian Westphal. 2) Missing counters and timestamp in nfnetlink_queue and _log conntrack information. 3) Missing error check for xt_register_template() in iptables mangle, as a incremental fix for the previous pull request, also from Florian Westphal. 4) Add netfilter hooks for the SRv6 lightweigh tunnel driver, from Ryoga Sato. The hooks are enabled via nf_hooks_lwtunnel sysctl to make sure existing netfilter rulesets do not break. There is a static key to disable the hooks by default. The pktgen_bench_xmit_mode_netif_receive.sh shows no noticeable impact in the seg6_input path for non-netfilter users: similar numbers with and without this patch. This is a sample of the perf report output: 11.67% kpktgend_0 [ipv6] [k] ipv6_get_saddr_eval 7.89% kpktgend_0 [ipv6] [k] __ipv6_addr_label 7.52% kpktgend_0 [ipv6] [k] __ipv6_dev_get_saddr 6.63% kpktgend_0 [kernel.vmlinux] [k] asm_exc_nmi 4.74% kpktgend_0 [ipv6] [k] fib6_node_lookup_1 3.48% kpktgend_0 [kernel.vmlinux] [k] pskb_expand_head 3.33% kpktgend_0 [ipv6] [k] ip6_rcv_core.isra.29 3.33% kpktgend_0 [ipv6] [k] seg6_do_srh_encap 2.53% kpktgend_0 [ipv6] [k] ipv6_dev_get_saddr 2.45% kpktgend_0 [ipv6] [k] fib6_table_lookup 2.24% kpktgend_0 [kernel.vmlinux] [k] ___cache_free 2.16% kpktgend_0 [ipv6] [k] ip6_pol_route 2.11% kpktgend_0 [kernel.vmlinux] [k] __ipv6_addr_type ==================== Signed-off-by: -
David S. Miller authored
Linus Walleij says: ==================== IXP46x PTP Timer clean-up and DT ChangeLog v2->v3: - Dropped the patch enabling compile tests: we are still dependent on some machine-specific headers. The plan is to get rid of this after device tree conversion. We include one of the compile testing fixes anyway, because it is nice to have fixed. - Rebased on the latest net-next ==================== Signed-off-by: -
Linus Walleij authored
This adds device tree probing support for the PTP module adjacent to the ethernet module. It is pretty straight forward, all resources are in the device tree as they come to the platform device. Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
This adds device tree bindings for the IXP46x PTP Timer, a companion to the IXP4xx ethernet in newer platforms. Cc: devicetree@vger.kernel.org Cc: Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Linus Walleij authored
The driver is being passed interrupts, then looking up the same interrupts as GPIOs a second time to convert them into interrupts and set properties on them. This is pointless: the GPIO and irqchip APIs of a GPIO chip are orthogonal. Just request the interrupts and be done with it, drop reliance on any GPIO functions or definitions. Use devres-managed functions and add a small devress quirk to unregister the clock as well and we can rely on devres to handle all the resources and cut down a bunch of boilerplate in the process. Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Arnd Bergmann authored
Change the driver to use portable integer types to avoid warnings during compile testing, including: drivers/net/ethernet/xscale/ixp4xx_eth.c:721:21: error: cast to 'u32 *' (aka 'unsigned int *') from smaller integer type 'int' [-Werror,-Wint-to-pointer-cast] memcpy_swab32(mem, (u32 *)((int)skb->data & ~3), bytes / 4); ^ drivers/net/ethernet/xscale/ixp4xx_eth.c:963:12: error: incompatible pointer types passing 'u32 *' (aka 'unsigned int *') to parameter of type 'dma_addr_t *' (aka 'unsigned long long *') [-Werror,-Wincompatible-pointer-types] &port->desc_tab_phys))) ^~~~~~~~~~~~~~~~~~~~ include/linux/dmapool.h:27:20: note: passing argument to parameter 'handle' here dma_addr_t *handle); ^ Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Arnd Bergmann authored
After the recent ixp4xx cleanups, the ptp driver has gained a build failure in some configurations: drivers/net/ethernet/xscale/ptp_ixp46x.c: In function 'ptp_ixp_init': drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: error: 'IXP4XX_TIMESYNC_BASE_VIRT' undeclared (first use in this function) Avoid the last bit of hardcoded constants from platform headers by turning the ptp driver bit into a platform driver and passing the IRQ and MMIO address as resources. This is a bit tricky: - The interface between the two drivers is now the new ixp46x_ptp_find() function, replacing the global ixp46x_phc_index variable. The call is done as late as possible, in hwtstamp_set(), to ensure that the ptp device is fully probed. - As the ptp driver is now called by the network driver, the link dependency is reversed, which in turn requires a small Makefile hack - The GPIO number is still left hardcoded. This is clearly not great, but it can be addressed later. Note that commit 98ac0cc2 ("ARM: ixp4xx: Convert to MULTI_IRQ_HANDLER") changed the IRQ number to something meaningless. Passing the correct IRQ in a resource fixes this. - When the PTP driver is disabled, ethtool .get_ts_info() now correctly lists only software timestamping regardless of the hardware. Signed-off-by:
-
David S. Miller authored
Guangbin Huang says: ==================== net: hns3: add some cleanups This series includes some cleanups for the HNS3 ethernet driver. ==================== Signed-off-by: -
Hao Chen authored
The parameter name of hclge_ptp_clean_tx_hwts() in declaration is "dev", but the definition of this function is used the common name "hdev" as other functions, so modify it. Signed-off-by:
Hao Chen <chenhao288@hisilicon.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
Hao Chen authored
Replace the "? :" statement wich max() to simplify code. Signed-off-by:
-
Hao Chen authored
The type of tqp_vector->vector_irq is int, so modify its print format to "%d". Signed-off-by:
-
Guangbin Huang authored
To improve flexibility, simplicity and maintainability to dump info of every element of tm priority, add a struct hclge_dbg_item array of tm priority and fill string of every data according to this array. Signed-off-by:
-
Guangbin Huang authored
This patch reconstructs function hclge_ets_validate() to reduce the code cycle complexity and make code more concise. Signed-off-by:
-
Peng Li authored
This patch reconstructs function hns3_self_test to reduce the code cycle complexity and make code more concise. Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
-
Jiaran Zhang authored
To make the format of each member initialization of structure array clearer, initialize each member on a separate line. Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Implement new driver APIs to send FW messages The current driver APIs to send messages to the firmware allow only one outstanding message in flight. There is only one buffer for the firmware response for each firmware channel. To send a firmware message, all callers must take a mutex and it is released after the firmware response has been read. This scheme does not allow multiple firmware messages in flight. Firmware may take a long time to respond to some messages (e.g. NVRAM related ones) and this causes the mutex to be held for a long time, blocking other callers. This patchset intoduces the new driver APIs to address the above shortcomings. The new APIs are compatible with new and old firmware. But the new deferred firmware response mechanism will require newer firmware in order to allow multiple outstanding firmware commands. All callers are updated to use the new APIs. v2: Patch 4 and patch 9 updated to fix issues reported by test robot ==================== Signed-off-by: -
Edwin Peer authored
Add infrastructure to maintain a pending list of HWRM commands awaiting completion and reduce the scope of the hwrm_cmd_lock mutex so that it protects only the request mailbox. The mailbox is free to use for one or more concurrent commands after receiving deferred response events. For uniformity and completeness, use the same pending list for collecting completions for commands that respond via a completion ring. These commands are only used for freeing rings and for IRQ test and we only support one such command in flight. Note deferred responses are also only supported on the main channel. The secondary channel (KONG) does not support deferred responses. Signed-off-by:
Edwin Peer <edwin.peer@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Edwin Peer authored
There are no longer any callers relying on the old API. Signed-off-by:
-
