- 27 Oct, 2015 18 commits
-
-
Mika Westerberg authored
commit 56d4b8a2 upstream. ACPI SSCN/FMCN methods were originally added because then the platform can provide the most accurate HCNT/LCNT values to the driver. However, this seems not to be true for Dell Inspiron 7348 where using these causes the touchpad to fail in boot: i2c_hid i2c-DLL0675:00: failed to retrieve report from device. i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration i2c_hid i2c-DLL0675:00: failed to retrieve report from device. i2c_designware INT3433:00: controller timed out The values received from ACPI are (in fast mode): HCNT: 72 LCNT: 160 this translates to following timings (input clock is 100MHz on Broadwell): tHIGH: 720 ns (spec min 600 ns) tLOW: 1600 ns (spec min 1300 ns) Bus period: 2920 ns (assuming 300 ns tf and tr) Bus speed: 342.5 kHz Both tHIGH and tLOW are within the I2C specification. The calculated values when ACPI parameters are not used are (in fast mode): HCNT: 87 LCNT: 159 which translates to: tHIGH: 870 ns (spec min 600 ns) tLOW: 1590 ns (spec min 1300 ns) Bus period 3060 ns (assuming 300 ns tf and tr) Bus speed 326.8 kHz These values are also within the I2C specification. Since both ACPI and calculated values meet the I2C specification timing requirements it is hard to say why the touchpad does not function properly with the ACPI values except that the bus speed is higher in this case (but still well below the max 400kHz). Solve this by adding DMI quirk to the driver that disables using ACPI parameters on this particulare machine. Reported-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Wolfram Sang authored
commit eadd709f upstream. The core may register clients attached to this master which may use funtionality from the master. So, RuntimePM must be enabled before, otherwise this will fail. While here, move drvdata, too. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Kukjin Kim <kgene@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Wolfram Sang authored
commit 4f7effdd upstream. The core may register clients attached to this master which may use funtionality from the master. So, RuntimePM must be enabled before, otherwise this will fail. While here, move drvdata, too. Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Will Deacon authored
commit b6dd8e07 upstream. Commit df057cc7 ("arm64: errata: add module build workaround for erratum #843419") sets CFLAGS_MODULE to ensure that the large memory model is used by the compiler when building kernel modules. However, CFLAGS_MODULE is an environment variable and intended to be overridden on the command line, which appears to be the case with the Ubuntu kernel packaging system, so use KBUILD_CFLAGS_MODULE instead. Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Fixes: df057cc7 ("arm64: errata: add module build workaround for erratum #843419") Reported-by: Dann Frazier <dann.frazier@canonical.com> Tested-by: Dann Frazier <dann.frazier@canonical.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Chris Mason authored
commit dc6c5fb3 upstream. The code for btrfs inode-resolve has never worked properly for files with enough hard links to trigger extrefs. It was trying to get the leaf out of a path after freeing the path: btrfs_release_path(path); leaf = path->nodes[0]; item_size = btrfs_item_size_nr(leaf, slot); The fix here is to use the extent buffer we cloned just a little higher up to avoid deadlocks caused by using the leaf in the path. Signed-off-by: Chris Mason <clm@fb.com> cc: Mark Fasheh <mfasheh@suse.de> Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Mark Fasheh <mfasheh@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
commit 8996eafd upstream. Unlike shash algorithms, ahash drivers must implement export and import as their descriptors may contain hardware state and cannot be exported as is. Unfortunately some ahash drivers did not provide them and end up causing crashes with algif_hash. This patch adds a check to prevent these drivers from registering ahash algorithms until they are fixed. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dave Kleikamp authored
commit a66d7f72 upstream. Some of the crypto algorithms write to the initialization vector, but no space has been allocated for it. This clobbers adjacent memory. Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Charles Keepax authored
[ Upstream commit 436c2a50 ] commit 3cc81d85 ("asix: Don't reset PHY on if_up for ASIX 88772") causes the ethernet on Arndale to no longer function. This appears to be because the Arndale ethernet requires a full reset before it will function correctly, however simply reverting the above patch causes problems with ethtool settings getting reset. It seems the problem is that the ethernet is not properly reset during bind, and indeed the code in ax88772_bind that resets the device is a very small subset of the actual ax88772_reset function. This patch uses ax88772_reset in place of the existing reset code in ax88772_bind which removes some code duplication and fixes the ethernet on Arndale. It is still possible that the original patch causes some issues with suspend and resume but that seems like a separate issue and I haven't had a chance to test that yet. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Tested-by: Riku Voipio <riku.voipio@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michel Stam authored
[ Upstream commit 3cc81d85 ] I've noticed every time the interface is set to 'up,', the kernel reports that the link speed is set to 100 Mbps/Full Duplex, even when ethtool is used to set autonegotiation to 'off', half duplex, 10 Mbps. It can be tested by: ifconfig eth0 down ethtool -s eth0 autoneg off speed 10 duplex half ifconfig eth0 up Then checking 'dmesg' for the link speed. Signed-off-by: Michel Stam <m.stam@fugro.nl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joe Perches authored
[ Upstream commit 077cb37f ] It seems that kernel memory can leak into userspace by a kmalloc, ethtool_get_strings, then copy_to_user sequence. Avoid this by using kcalloc to zero fill the copied buffer. Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Guillaume Nault authored
[ Upstream commit e6740165 ] Since commit 2b018d57 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release"), pppoe_release() calls dev_put(po->pppoe_dev) if sk is in the PPPOX_ZOMBIE state. But pppoe_flush_dev() can set sk->sk_state to PPPOX_ZOMBIE _and_ reset po->pppoe_dev to NULL. This leads to the following oops: [ 570.140800] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e0 [ 570.142931] IP: [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] PGD 3d119067 PUD 3dbc1067 PMD 0 [ 570.144601] Oops: 0000 [#1] SMP [ 570.144601] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppoe pppox ppp_generic slhc loop crc32c_intel ghash_clmulni_intel jitterentropy_rng sha256_generic hmac drbg ansi_cprng aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper acpi_cpufreq evdev serio_raw processor button ext4 crc16 mbcache jbd2 virtio_net virtio_blk virtio_pci virtio_ring virtio [ 570.144601] CPU: 1 PID: 15738 Comm: ppp-apitest Not tainted 4.2.0 #1 [ 570.144601] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014 [ 570.144601] task: ffff88003d30d600 ti: ffff880036b60000 task.ti: ffff880036b60000 [ 570.144601] RIP: 0010:[<ffffffffa018c701>] [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP: 0018:ffff880036b63e08 EFLAGS: 00010202 [ 570.144601] RAX: 0000000000000000 RBX: ffff880034340000 RCX: 0000000000000206 [ 570.144601] RDX: 0000000000000006 RSI: ffff88003d30dd20 RDI: ffff88003d30dd20 [ 570.144601] RBP: ffff880036b63e28 R08: 0000000000000001 R09: 0000000000000000 [ 570.144601] R10: 00007ffee9b50420 R11: ffff880034340078 R12: ffff8800387ec780 [ 570.144601] R13: ffff8800387ec7b0 R14: ffff88003e222aa0 R15: ffff8800387ec7b0 [ 570.144601] FS: 00007f5672f48700(0000) GS:ffff88003fc80000(0000) knlGS:0000000000000000 [ 570.144601] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 570.144601] CR2: 00000000000004e0 CR3: 0000000037f7e000 CR4: 00000000000406a0 [ 570.144601] Stack: [ 570.144601] ffffffffa018f240 ffff8800387ec780 ffffffffa018f240 ffff8800387ec7b0 [ 570.144601] ffff880036b63e48 ffffffff812caabe ffff880039e4e000 0000000000000008 [ 570.144601] ffff880036b63e58 ffffffff812cabad ffff880036b63ea8 ffffffff811347f5 [ 570.144601] Call Trace: [ 570.144601] [<ffffffff812caabe>] sock_release+0x1a/0x75 [ 570.144601] [<ffffffff812cabad>] sock_close+0xd/0x11 [ 570.144601] [<ffffffff811347f5>] __fput+0xff/0x1a5 [ 570.144601] [<ffffffff811348cb>] ____fput+0x9/0xb [ 570.144601] [<ffffffff81056682>] task_work_run+0x66/0x90 [ 570.144601] [<ffffffff8100189e>] prepare_exit_to_usermode+0x8c/0xa7 [ 570.144601] [<ffffffff81001a26>] syscall_return_slowpath+0x16d/0x19b [ 570.144601] [<ffffffff813babb1>] int_ret_from_sys_call+0x25/0x9f [ 570.144601] Code: 48 8b 83 c8 01 00 00 a8 01 74 12 48 89 df e8 8b 27 14 e1 b8 f7 ff ff ff e9 b7 00 00 00 8a 43 12 a8 0b 74 1c 48 8b 83 a8 04 00 00 <48> 8b 80 e0 04 00 00 65 ff 08 48 c7 83 a8 04 00 00 00 00 00 00 [ 570.144601] RIP [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP <ffff880036b63e08> [ 570.144601] CR2: 00000000000004e0 [ 570.200518] ---[ end trace 46956baf17349563 ]--- pppoe_flush_dev() has no reason to override sk->sk_state with PPPOX_ZOMBIE. pppox_unbind_sock() already sets sk->sk_state to PPPOX_DEAD, which is the correct state given that sk is unbound and po->pppoe_dev is NULL. Fixes: 2b018d57 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Tested-by: Oleksii Berezhniak <core@irc.lg.ua> Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric Dumazet authored
[ Upstream commit c7c49b8f ] Greg reported crashes hitting the following check in __sk_backlog_rcv() BUG_ON(!sock_flag(sk, SOCK_MEMALLOC)); The pfmemalloc bit is currently checked in sk_filter(). This works correctly for TCP, because sk_filter() is ran in tcp_v[46]_rcv() before hitting the prequeue or backlog checks. For UDP or other protocols, this does not work, because the sk_filter() is ran from sock_queue_rcv_skb(), which might be called _after_ backlog queuing if socket is owned by user by the time packet is processed by softirq handler. Fixes: b4b9e355 ("netvm: set PF_MEMALLOC as appropriate during SKB processing") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Greg Thelen <gthelen@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pravin B Shelar authored
[ Upstream commit 31b33dfb ] Earlier patch 6ae459bd tried to detect void ckecksum partial skb by comparing pull length to checksum offset. But it does not work for all cases since checksum-offset depends on updates to skb->data. Following patch fixes it by validating checksum start offset after skb-data pointer is updated. Negative value of checksum offset start means there is no need to checksum. Fixes: 6ae459bd ("skbuff: Fix skb checksum flag on skb pull") Reported-by: Andrew Vagin <avagin@odin.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pravin B Shelar authored
[ Upstream commit 6ae459bd ] VXLAN device can receive skb with checksum partial. But the checksum offset could be in outer header which is pulled on receive. This results in negative checksum offset for the skb. Such skb can cause the assert failure in skb_checksum_help(). Following patch fixes the bug by setting checksum-none while pulling outer header. Following is the kernel panic msg from old kernel hitting the bug. ------------[ cut here ]------------ kernel BUG at net/core/dev.c:1906! RIP: 0010:[<ffffffff81518034>] skb_checksum_help+0x144/0x150 Call Trace: <IRQ> [<ffffffffa0164c28>] queue_userspace_packet+0x408/0x470 [openvswitch] [<ffffffffa016614d>] ovs_dp_upcall+0x5d/0x60 [openvswitch] [<ffffffffa0166236>] ovs_dp_process_packet_with_key+0xe6/0x100 [openvswitch] [<ffffffffa016629b>] ovs_dp_process_received_packet+0x4b/0x80 [openvswitch] [<ffffffffa016c51a>] ovs_vport_receive+0x2a/0x30 [openvswitch] [<ffffffffa0171383>] vxlan_rcv+0x53/0x60 [openvswitch] [<ffffffffa01734cb>] vxlan_udp_encap_recv+0x8b/0xf0 [openvswitch] [<ffffffff8157addc>] udp_queue_rcv_skb+0x2dc/0x3b0 [<ffffffff8157b56f>] __udp4_lib_rcv+0x1cf/0x6c0 [<ffffffff8157ba7a>] udp_rcv+0x1a/0x20 [<ffffffff8154fdbd>] ip_local_deliver_finish+0xdd/0x280 [<ffffffff81550128>] ip_local_deliver+0x88/0x90 [<ffffffff8154fa7d>] ip_rcv_finish+0x10d/0x370 [<ffffffff81550365>] ip_rcv+0x235/0x300 [<ffffffff8151ba1d>] __netif_receive_skb+0x55d/0x620 [<ffffffff8151c360>] netif_receive_skb+0x80/0x90 [<ffffffff81459935>] virtnet_poll+0x555/0x6f0 [<ffffffff8151cd04>] net_rx_action+0x134/0x290 [<ffffffff810683d8>] __do_softirq+0xa8/0x210 [<ffffffff8162fe6c>] call_softirq+0x1c/0x30 [<ffffffff810161a5>] do_softirq+0x65/0xa0 [<ffffffff810687be>] irq_exit+0x8e/0xb0 [<ffffffff81630733>] do_IRQ+0x63/0xe0 [<ffffffff81625f2e>] common_interrupt+0x6e/0x6e Reported-by: Anupam Chanda <achanda@vmware.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Andrey Vagin authored
[ Upstream commit e9193d60 ] Now send with MSG_PEEK can return data from multiple SKBs. Unfortunately we take into account the peek offset for each skb, that is wrong. We need to apply the peek offset only once. In addition, the peek offset should be used only if MSG_PEEK is set. Cc: "David S. Miller" <davem@davemloft.net> (maintainer:NETWORKING Cc: Eric Dumazet <edumazet@google.com> (commit_signer:1/14=7%) Cc: Aaron Conole <aconole@bytheb.org> Fixes: 9f389e35 ("af_unix: return data from multiple SKBs on recv() with MSG_PEEK flag") Signed-off-by: Andrey Vagin <avagin@openvz.org> Tested-by: Aaron Conole <aconole@bytheb.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Aaron Conole authored
[ Upstream commit 9f389e35 ] AF_UNIX sockets now return multiple skbs from recv() when MSG_PEEK flag is set. This is referenced in kernel bugzilla #12323 @ https://bugzilla.kernel.org/show_bug.cgi?id=12323 As described both in the BZ and lkml thread @ http://lkml.org/lkml/2008/1/8/444 calling recv() with MSG_PEEK on an AF_UNIX socket only reads a single skb, where the desired effect is to return as much skb data has been queued, until hitting the recv buffer size (whichever comes first). The modified MSG_PEEK path will now move to the next skb in the tree and jump to the again: label, rather than following the natural loop structure. This requires duplicating some of the loop head actions. This was tested using the python socketpair python code attached to the bugzilla issue. Signed-off-by: Aaron Conole <aconole@bytheb.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Aaron Conole authored
[ Upstream commit 4613012d ] As suggested by Eric Dumazet this change replaces the #define with a static inline function to enjoy complaints by the compiler when misusing the API. Signed-off-by: Aaron Conole <aconole@bytheb.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexander Couzens authored
[ Upstream commit 06a15f51 ] There is a small chance that tunnel_free() is called before tunnel->del_work scheduled resulting in a zero pointer dereference. Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Acked-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 22 Oct, 2015 22 commits
-
-
Greg Kroah-Hartman authored
-
Peter Zijlstra authored
commit 2ab08ee9 upstream. Both already use asm-generic/barrier.h as per their include/asm/Kbuild. Remove the stale files. Signed-off-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Link: http://lkml.kernel.org/n/tip-c7vlkshl3tblim0o8z2p70kt@git.kernel.org Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Richard Kuo <rkuo@codeaurora.org> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: linux-hexagon@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Christoph Hellwig authored
commit 15e3d5a2 upstream. 3w controller don't dma map small single SGL entry commands but instead bounce buffer them. Add a helper to identify these commands and don't call scsi_dma_unmap for them. Based on an earlier patch from James Bottomley. Fixes: 118c85 ("3w-9xxx: fix command completion race") Reported-by: Tóth Attila <atoth@atoth.sote.hu> Tested-by: Tóth Attila <atoth@atoth.sote.hu> Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joonsoo Kim authored
commit 03a2d2a3 upstream. Commit description is copied from the original post of this bug: http://comments.gmane.org/gmane.linux.kernel.mm/135349 Kernels after v3.9 use kmalloc_size(INDEX_NODE + 1) to get the next larger cache size than the size index INDEX_NODE mapping. In kernels 3.9 and earlier we used malloc_sizes[INDEX_L3 + 1].cs_size. However, sometimes we can't get the right output we expected via kmalloc_size(INDEX_NODE + 1), causing a BUG(). The mapping table in the latest kernel is like: index = {0, 1, 2 , 3, 4, 5, 6, n} size = {0, 96, 192, 8, 16, 32, 64, 2^n} The mapping table before 3.10 is like this: index = {0 , 1 , 2, 3, 4 , 5 , 6, n} size = {32, 64, 96, 128, 192, 256, 512, 2^(n+3)} The problem on my mips64 machine is as follows: (1) When configured DEBUG_SLAB && DEBUG_PAGEALLOC && DEBUG_LOCK_ALLOC && DEBUG_SPINLOCK, the sizeof(struct kmem_cache_node) will be "150", and the macro INDEX_NODE turns out to be "2": #define INDEX_NODE kmalloc_index(sizeof(struct kmem_cache_node)) (2) Then the result of kmalloc_size(INDEX_NODE + 1) is 8. (3) Then "if(size >= kmalloc_size(INDEX_NODE + 1)" will lead to "size = PAGE_SIZE". (4) Then "if ((size >= (PAGE_SIZE >> 3))" test will be satisfied and "flags |= CFLGS_OFF_SLAB" will be covered. (5) if (flags & CFLGS_OFF_SLAB)" test will be satisfied and will go to "cachep->slabp_cache = kmalloc_slab(slab_size, 0u)", and the result here may be NULL while kernel bootup. (6) Finally,"BUG_ON(ZERO_OR_NULL_PTR(cachep->slabp_cache));" causes the BUG info as the following shows (may be only mips64 has this problem): This patch fixes the problem of kmalloc_size(INDEX_NODE + 1) and removes the BUG by adding 'size >= 256' check to guarantee that all necessary small sized slabs are initialized regardless sequence of slab size in mapping table. Fixes: e3366016 ("slab: Use common kmalloc_index/kmalloc_size...") Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-by: Liuhailong <liu.hailong6@zte.com.cn> Acked-by: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
covici@ccs.covici.com authored
commit b1d562ac upstream. Here is a patch to make speakup-r work again. It broke in 3.6 due to commit 4369c64c "Input: Send events one packet at a time) The problem was that the fakekey.c routine to fake a down arrow no longer functioned properly and putting the input_sync fixed it. Fixes: 4369c64cAcked-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: John Covici <covici@ccs.covici.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joe Thornber authored
commit 2bffa150 upstream. The cleaner policy doesn't make use of the per cache block hint space in the metadata (unlike the other policies). When switching from the cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block) was observed. The crash was caused by bugs in dm-cache-metadata.c when trying to skip creation of the hint btree. The minimal fix is to change hint size for the cleaner policy to 4 bytes (only hint size supported). Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ben Dooks authored
commit 19e79687 upstream. On the OMAP AM3517 platform the uart4_ick gets registered twice, causing any power management to /dev/ttyO3 to fail when trying to wake the device up. This solves the following oops: [] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008 [] PC is at serial_omap_pm+0x48/0x15c [] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c Fixes: aafd900c ("CLK: TI: add omap3 clock init file") Cc: mturquette@baylibre.com Cc: sboyd@codeaurora.org Cc: linux-clk@vger.kernel.org Cc: linux-omap@vger.kernel.org Cc: linux-kernel@lists.codethink.co.uk Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jan Kara authored
commit 841df7df upstream. Commit 6f6a6fda "jbd2: fix ocfs2 corrupt when updating journal superblock fails" changed jbd2_cleanup_journal_tail() to return EIO when the journal is aborted. That makes logic in jbd2_log_do_checkpoint() bail out which is fine, except that jbd2_journal_destroy() expects jbd2_log_do_checkpoint() to always make a progress in cleaning the journal. Without it jbd2_journal_destroy() just loops in an infinite loop. Fix jbd2_journal_destroy() to cleanup journal checkpoint lists of jbd2_log_do_checkpoint() fails with error. Reported-by: Eryu Guan <guaneryu@gmail.com> Tested-by: Eryu Guan <guaneryu@gmail.com> Fixes: 6f6a6fdaSigned-off-by: Jan Kara <jack@suse.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ben Hutchings authored
commit 95c2b175 upstream. Per-IRQ directories in procfs are created only when a handler is first added to the irqdesc, not when the irqdesc is created. In the case of a shared IRQ, multiple tasks can race to create a directory. This race condition seems to have been present forever, but is easier to hit with async probing. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Link: http://lkml.kernel.org/r/1443266636.2004.2.camel@decadent.org.ukSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Roland Dreier authored
Backports of 41fc0143 ("fib_rules: fix fib rule dumps across multiple skbs") introduced a regression in "ip rule show" - it ends up dumping the first rule over and over and never exiting, because 3.19 and earlier are missing commit 053c095a ("netlink: make nlmsg_end() and genlmsg_end() void"), so fib_nl_fill_rule() ends up returning skb->len (i.e. > 0) in the success case. Fix this by checking the return code for < 0 instead of != 0. Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Andreas Schwab authored
commit 8474ba74 upstream. Make sure the compiler does not modify arguments of syscall functions. This can happen if the compiler generates a tailcall to another function. For example, without asmlinkage_protect sys_openat is compiled into this function: sys_openat: clr.l %d0 move.w 18(%sp),%d0 move.l %d0,16(%sp) jbra do_sys_open Note how the fourth argument is modified in place, modifying the register %d4 that gets restored from this stack slot when the function returns to user-space. The caller may expect the register to be unmodified across system calls. Signed-off-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mark Salyzyn authored
commit 569ba74a upstream. This is the arm64 portion of commit 45cac65b ("readahead: fault retry breaks mmap file read random detection"), which was absent from the initial port and has since gone unnoticed. The original commit says: > .fault now can retry. The retry can break state machine of .fault. In > filemap_fault, if page is miss, ra->mmap_miss is increased. In the second > try, since the page is in page cache now, ra->mmap_miss is decreased. And > these are done in one fault, so we can't detect random mmap file access. > > Add a new flag to indicate .fault is tried once. In the second try, skip > ra->mmap_miss decreasing. The filemap_fault state machine is ok with it. With this change, Mark reports that: > Random read improves by 250%, sequential read improves by 40%, and > random write by 400% to an eMMC device with dm crypto wrapped around it. Cc: Shaohua Li <shli@kernel.org> Cc: Rik van Riel <riel@redhat.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Mark Salyzyn <salyzyn@android.com> Signed-off-by: Riley Andrews <riandrews@android.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric W. Biederman authored
commit 397d425d upstream. In rare cases a directory can be renamed out from under a bind mount. In those cases without special handling it becomes possible to walk up the directory tree to the root dentry of the filesystem and down from the root dentry to every other file or directory on the filesystem. Like division by zero .. from an unconnected path can not be given a useful semantic as there is no predicting at which path component the code will realize it is unconnected. We certainly can not match the current behavior as the current behavior is a security hole. Therefore when encounting .. when following an unconnected path return -ENOENT. - Add a function path_connected to verify path->dentry is reachable from path->mnt.mnt_root. AKA to validate that rename did not do something nasty to the bind mount. To avoid races path_connected must be called after following a path component to it's next path component. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric W. Biederman authored
commit cde93be4 upstream. A rename can result in a dentry that by walking up d_parent will never reach it's mnt_root. For lack of a better term I call this an escaped path. prepend_path is called by four different functions __d_path, d_absolute_path, d_path, and getcwd. __d_path only wants to see paths are connected to the root it passes in. So __d_path needs prepend_path to return an error. d_absolute_path similarly wants to see paths that are connected to some root. Escaped paths are not connected to any mnt_root so d_absolute_path needs prepend_path to return an error greater than 1. So escaped paths will be treated like paths on lazily unmounted mounts. getcwd needs to prepend "(unreachable)" so getcwd also needs prepend_path to return an error. d_path is the interesting hold out. d_path just wants to print something, and does not care about the weird cases. Which raises the question what should be printed? Given that <escaped_path>/<anything> should result in -ENOENT I believe it is desirable for escaped paths to be printed as empty paths. As there are not really any meaninful path components when considered from the perspective of a mount tree. So tweak prepend_path to return an empty path with an new error code of 3 when it encounters an escaped path. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
shengyong authored
commit 7c7feb2e upstream. UBI: attaching mtd1 to ubi0 UBI: scanning is finished UBI error: init_volumes: not enough PEBs, required 706, available 686 UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1) UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM UBI error: ubi_init: cannot attach mtd1 If available PEBs are not enough when initializing volumes, return -ENOSPC directly. If available PEBs are not enough when initializing WL, return -ENOSPC instead of -ENOMEM. Signed-off-by: Sheng Yong <shengyong1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Richard Weinberger authored
commit 281fda27 upstream. Make sure that data_size is less than LEB size. Otherwise a handcrafted UBI image is able to trigger an out of bounds memory access in ubi_compare_lebs(). Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Paul Mackerras authored
commit e297c939 upstream. This fixes a race which can result in the same virtual IRQ number being assigned to two different MSI interrupts. The most visible consequence of that is usually a warning and stack trace from the sysfs code about an attempt to create a duplicate entry in sysfs. The race happens when one CPU (say CPU 0) is disposing of an MSI while another CPU (say CPU 1) is setting up an MSI. CPU 0 calls (for example) pnv_teardown_msi_irqs(), which calls msi_bitmap_free_hwirqs() to indicate that the MSI (i.e. its hardware IRQ number) is no longer in use. Then, before CPU 0 gets to calling irq_dispose_mapping() to free up the virtal IRQ number, CPU 1 comes in and calls msi_bitmap_alloc_hwirqs() to allocate an MSI, and gets the same hardware IRQ number that CPU 0 just freed. CPU 1 then calls irq_create_mapping() to get a virtual IRQ number, which sees that there is currently a mapping for that hardware IRQ number and returns the corresponding virtual IRQ number (which is the same virtual IRQ number that CPU 0 was using). CPU 0 then calls irq_dispose_mapping() and frees that virtual IRQ number. Now, if another CPU comes along and calls irq_create_mapping(), it is likely to get the virtual IRQ number that was just freed, resulting in the same virtual IRQ number apparently being used for two different hardware interrupts. To fix this race, we just move the call to msi_bitmap_free_hwirqs() to after the call to irq_dispose_mapping(). Since virq_to_hw() doesn't work for the virtual IRQ number after irq_dispose_mapping() has been called, we need to call it before irq_dispose_mapping() and remember the result for the msi_bitmap_free_hwirqs() call. The pattern of calling msi_bitmap_free_hwirqs() before irq_dispose_mapping() appears in 5 places under arch/powerpc, and appears to have originated in commit 05af7bd2 ("[POWERPC] MPIC U3/U4 MSI backend") from 2007. Fixes: 05af7bd2 ("[POWERPC] MPIC U3/U4 MSI backend") Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
NeilBrown authored
commit ee5d004f upstream. The 'event_work' worker used by dm-raid may still be running when the array is stopped. This can result in an oops. So flush the workqueue on which it is run after detaching and before destroying the device. Reported-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: NeilBrown <neilb@suse.com> Fixes: 9d09e663 ("dm: raid456 basic support") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ian Abbott authored
commit c04a1f17 upstream. `devpriv->ao_timer` is used while an asynchronous command is running on the AO subdevice. It also gets modified by the subdevice's `cmdtest` handler for checking new asynchronous commands, `usbduxsigma_ao_cmdtest()`, which is not correct as it's allowed to check new commands while an old command is still running. Fix it by moving the code which sets up `devpriv->ao_timer` into the subdevice's `cmd` handler, `usbduxsigma_ao_cmd()`. Note that the removed code in `usbduxsigma_ao_cmdtest()` checked that `devpriv->ao_timer` did not end up less that 1, but that could not happen due because `cmd->scan_begin_arg` or `cmd->convert_arg` had already been range-checked. Also note that we tested the `high_speed` variable in the old code, but that is currently always 0 and means that we always use "scan" timing (`cmd->scan_begin_src == TRIG_TIMER` and `cmd->convert_src == TRIG_NOW`) and never "convert" (individual sample) timing (`cmd->scan_begin_src == TRIG_FOLLOW` and `cmd->convert_src == TRIG_TIMER`). The moved code tests `cmd->convert_src` instead to decide whether "scan" or "convert" timing is being used, although currently only "scan" timing is supported. Fixes: fb1ef622 ("staging: comedi: usbduxsigma: tidy up analog output command support") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: Bernd Porr <mail@berndporr.me.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ian Abbott authored
commit 423b24c3 upstream. `devpriv->ai_timer` is used while an asynchronous command is running on the AI subdevice. It also gets modified by the subdevice's `cmdtest` handler for checking new asynchronous commands (`usbduxsigma_ai_cmdtest()`), which is not correct as it's allowed to check new commands while an old command is still running. Fix it by moving the code which sets up `devpriv->ai_timer` and `devpriv->ai_interval` into the subdevice's `cmd` handler, `usbduxsigma_ai_cmd()`. Note that the removed code in `usbduxsigma_ai_cmdtest()` checked that `devpriv->ai_timer` did not end up less than than 1, but that could not happen because `cmd->scan_begin_arg` had already been checked to be at least the minimum required value (at least when `cmd->scan_begin_src == TRIG_TIMER`, which had also been checked to be the case). Fixes: b986be85 ("staging: comedi: usbduxsigma: tidy up analog input command support) Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: Bernd Porr <mail@berndporr.me.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
James Hogan authored
commit 53960059 upstream. If there is a DMA zone (usually 24bit = 16MB I believe), but no DMA32 zone, as is the case for some 32-bit kernels, then massage_gfp_flags() will cause DMA memory allocated for devices with a 32..63-bit coherent_dma_mask to fall back to using __GFP_DMA, even though there may only be 32-bits of physical address available anyway. Correct that case to compare against a mask the size of phys_addr_t instead of always using a 64-bit mask. Signed-off-by: James Hogan <james.hogan@imgtec.com> Fixes: a2e715a8 ("MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.") Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/9610/Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Yao-Wen Mao authored
commit 8484bf29 upstream. These two headphones need a reset-resume quirk to properly resume to original volume level. Signed-off-by: Yao-Wen Mao <yaowen@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-