An error occurred fetching the project authors.
- 19 Aug, 2015 18 commits
-
-
Oliver Neukum authored
commit 5fb2c782 upstream. This device automatically switches itself to another mode (0x1405) unless the specific access pattern of Windows is followed in its initial mode. That makes a dirty unmount of the internal storage devices inevitable if they are mounted. So the card reader of such a device should be ignored, lest an unclean removal become inevitable. This replaces an earlier patch that ignored all LUNs of this device. That patch was overly broad. Signed-off-by: Oliver Neukum <oneukum@suse.com> Reviewed-by: Lars Melin <larsm17@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Lior Amsalem authored
commit 945b4744 upstream. This commit adds the necessary quirk to make the Marvell 4140 SATA PMP work properly. This PMP doesn't like SRST on port number 4 (the host port) so this commit marks this port as not supporting SRST. Signed-off-by: Lior Amsalem <alior@marvell.com> Reviewed-by: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Tejun Heo authored
commit 5f6c2d2b upstream. When a blkcg configuration is targeted to a partition rather than a whole device, blkg_conf_prep fails with -EINVAL; unfortunately, it forgets to put the gendisk ref in that case. Fix it. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Bernhard Bender authored
commit 96849170 upstream. This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30 touch screen. Due to a missing delay between the RESET and SET_RATE commands, the touch screen may become unresponsive during system startup or driver loading. According to the DMC documentation, a delay is needed after the RESET command to allow the chip to complete its internal initialization. As this delay is not guaranteed, we had a system where the touch screen occasionally did not send any touch data. There was no other indication of the problem. The patch fixes the problem by adding a 150ms delay between the RESET and SET_RATE commands. Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com> Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Chris Metcalf authored
commit 3f81d244 upstream. We were previously using free_bootmem() and just getting lucky that nothing too bad happened. Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
NeilBrown authored
commit 34cab6f4 upstream. When we get a read error from the last working device, we don't try to repair it, and don't fail the device. We simple report a read error to the caller. However the current test for 'is this the last working device' is wrong. When there is only one fully working device, it assumes that a non-faulty device is that device. However a spare which is rebuilding would be non-faulty but so not the only working device. So change the test from "!Faulty" to "In_sync". If ->degraded says there is only one fully working device and this device is in_sync, this must be the one. This bug has existed since we allowed read_balance to read from a recovering spare in v3.0 Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054 ("md/raid1: clean up read_balance.") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Jingju Hou authored
commit 9cd76049 upstream. pdev->dev.platform_data is not initialized if match is true in function sdhci_pxav3_probe. Just local variable pdata is assigned the return value from function pxav3_get_mmc_pdata(). static int sdhci_pxav3_probe(struct platform_device *pdev) { struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; ... if (match) { ret = mmc_of_parse(host->mmc); if (ret) goto err_of_parse; sdhci_get_of_property(pdev); pdata = pxav3_get_mmc_pdata(dev); } ... } Signed-off-by: Jingju Hou <houjingj@marvell.com> Fixes: b650352d("mmc: sdhci-pxa: Add device tree support") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Joakim Tjernlund authored
commit 8e91125f upstream. Support for 8BIT bus with was added some time ago to sdhci-esdhc but then missed to remove the 8BIT from the reserved bit mask which made 8BIT non functional. Fixes: 66b50a00 ("mmc: esdhc: Add support for 8-bit bus width and..") Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Tom Hughes authored
commit 4479004e upstream. If we don't do this, and we then fail to recreate the debugfs directory during a mode change, then we will fail later trying to add stations to this now bogus directory: BUG: unable to handle kernel NULL pointer dereference at 0000006c IP: [<c0a92202>] mutex_lock+0x12/0x30 Call Trace: [<c0678ab4>] start_creating+0x44/0xc0 [<c0679203>] debugfs_create_dir+0x13/0xf0 [<f8a938ae>] ieee80211_sta_debugfs_add+0x6e/0x490 [mac80211] Signed-off-by: Tom Hughes <tom@compton.nu> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Seymour, Shane M authored
commit e7ac6c66 upstream. Two SLES11 SP3 servers encountered similar crashes simultaneously following some kind of SAN/tape target issue: ... qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-8009:3: DEVICE RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: DEVICE RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8009:3: TARGET RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: TARGET RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8012:3: BUS RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-802b:3: BUS RESET SUCCEEDED nexus=3:0:2. qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8018:3: ADAPTER RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-00af:3: Performing ISP error recovery - ha=ffff88bf04d18000. rport-3:0-0: blocked FC remote port time out: removing target and saving binding qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8017:3: ADAPTER RESET SUCCEEDED nexus=3:0:2. rport-2:0-0: blocked FC remote port time out: removing target and saving binding sg_rq_end_io: device detached BUG: unable to handle kernel NULL pointer dereference at 00000000000002a8 IP: [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 PGD 7e6586f067 PUD 7e5af06067 PMD 0 [1739975.390354] Oops: 0002 [#1] SMP CPU 0 ... Supported: No, Proprietary modules are loaded [1739975.390463] Pid: 27965, comm: ABCD Tainted: PF X 3.0.101-0.29-default #1 HP ProLiant DL580 Gen8 RIP: 0010:[<ffffffff8133b268>] [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP: 0018:ffff8839dc1e7c68 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff883f0592fc00 RCX: 0000000000000090 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000138 RBP: 0000000000000138 R08: 0000000000000010 R09: ffffffff81bd39d0 R10: 00000000000009c0 R11: ffffffff81025790 R12: 0000000000000001 R13: ffff883022212b80 R14: 0000000000000004 R15: ffff883022212b80 FS: 00007f8e54560720(0000) GS:ffff88407f800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00000000000002a8 CR3: 0000007e6ced6000 CR4: 00000000001407f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process ABCD (pid: 27965, threadinfo ffff8839dc1e6000, task ffff883592e0c640) Stack: ffff883f0592fc00 00000000fffffffa 0000000000000001 ffff883022212b80 ffff883eff772400 ffffffffa03fa309 0000000000000000 0000000000000000 ffffffffa04003a0 ffff883f063196c0 ffff887f0379a930 ffffffff8115ea1e Call Trace: [<ffffffffa03fa309>] st_open+0x129/0x240 [st] [<ffffffff8115ea1e>] chrdev_open+0x13e/0x200 [<ffffffff811588a8>] __dentry_open+0x198/0x310 [<ffffffff81167d74>] do_last+0x1f4/0x800 [<ffffffff81168fe9>] path_openat+0xd9/0x420 [<ffffffff8116946c>] do_filp_open+0x4c/0xc0 [<ffffffff8115a00f>] do_sys_open+0x17f/0x250 [<ffffffff81468d92>] system_call_fastpath+0x16/0x1b [<00007f8e4f617fd0>] 0x7f8e4f617fcf Code: eb d3 90 48 83 ec 28 40 f6 c6 04 48 89 6c 24 08 4c 89 74 24 20 48 89 fd 48 89 1c 24 4c 89 64 24 10 41 89 f6 4c 89 6c 24 18 74 11 <f0> ff 8f 70 01 00 00 0f 94 c0 45 31 ed 84 c0 74 2b 4c 8d a5 a0 RIP [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP <ffff8839dc1e7c68> CR2: 00000000000002a8 Analysis reveals the cause of the crash to be due to STp->device being NULL. The pointer was NULLed via scsi_tape_put(STp) when it calls scsi_tape_release(). In st_open() we jump to err_out after scsi_block_when_processing_errors() completes and returns the device as offline (sdev_state was SDEV_DEL): 1180 /* Open the device. Needs to take the BKL only because of incrementing the SCSI host 1181 module count. */ 1182 static int st_open(struct inode *inode, struct file *filp) 1183 { 1184 int i, retval = (-EIO); 1185 int resumed = 0; 1186 struct scsi_tape *STp; 1187 struct st_partstat *STps; 1188 int dev = TAPE_NR(inode); 1189 char *name; ... 1217 if (scsi_autopm_get_device(STp->device) < 0) { 1218 retval = -EIO; 1219 goto err_out; 1220 } 1221 resumed = 1; 1222 if (!scsi_block_when_processing_errors(STp->device)) { 1223 retval = (-ENXIO); 1224 goto err_out; 1225 } ... 1264 err_out: 1265 normalize_buffer(STp->buffer); 1266 spin_lock(&st_use_lock); 1267 STp->in_use = 0; 1268 spin_unlock(&st_use_lock); 1269 scsi_tape_put(STp); <-- STp->device = 0 after this 1270 if (resumed) 1271 scsi_autopm_put_device(STp->device); 1272 return retval; The ref count for the struct scsi_tape had already been reduced to 1 when the .remove method of the st module had been called. The kref_put() in scsi_tape_put() caused scsi_tape_release() to be called: 0266 static void scsi_tape_put(struct scsi_tape *STp) 0267 { 0268 struct scsi_device *sdev = STp->device; 0269 0270 mutex_lock(&st_ref_mutex); 0271 kref_put(&STp->kref, scsi_tape_release); <-- calls this 0272 scsi_device_put(sdev); 0273 mutex_unlock(&st_ref_mutex); 0274 } In scsi_tape_release() the struct scsi_device in the struct scsi_tape gets set to NULL: 4273 static void scsi_tape_release(struct kref *kref) 4274 { 4275 struct scsi_tape *tpnt = to_scsi_tape(kref); 4276 struct gendisk *disk = tpnt->disk; 4277 4278 tpnt->device = NULL; <<<---- where the dev is nulled 4279 4280 if (tpnt->buffer) { 4281 normalize_buffer(tpnt->buffer); 4282 kfree(tpnt->buffer->reserved_pages); 4283 kfree(tpnt->buffer); 4284 } 4285 4286 disk->private_data = NULL; 4287 put_disk(disk); 4288 kfree(tpnt); 4289 return; 4290 } Although the problem was reported on SLES11.3 the problem appears in linux-next as well. The crash is fixed by reordering the code so we no longer access the struct scsi_tape after the kref_put() is done on it in st_open(). Signed-off-by: Shane Seymour <shane.seymour@hp.com> Signed-off-by: Darren Lavender <darren.lavender@hp.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com> Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Takashi Iwai authored
commit 649ccd08 upstream. MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this seems not working correctly, a fix for pin NID 0x15 is needed in addition. It's equivalent with the fixup for MacBook Air 1,1, so use this instead. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131Reported-and-tested-by: Jeffery Miller <jefferym@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Yao-Wen Mao authored
commit 2d1cb7f6 upstream. Add the correct dB ranges of Bose Companion 5 and Drangonfly DAC 1.2. Signed-off-by: Yao-Wen Mao <yaowen@google.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Dominic Sacré authored
commit 0689a86a upstream. The Steinberg MI2 and MI4 interfaces are compatible with the USB class audio spec, but the MIDI part of the devices is reported as a vendor specific interface. This patch adds entries to quirks-table.h to recognize the MIDI endpoints. Audio functionality was already working and is unaffected by this change. Signed-off-by: Dominic Sacré <dominic.sacre@gmx.de> Signed-off-by: Albert Huitsing <albert@huitsing.nl> Acked-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Thomas Gleixner authored
commit 75a06189 upstream. The resend mechanism happily calls the interrupt handler of interrupts which are marked IRQ_NESTED_THREAD from softirq context. This can result in crashes because the interrupt handler is not the proper way to invoke the device handlers. They must be invoked via handle_nested_irq. Prevent the resend even if the interrupt has no valid parent irq set. Its better to have a lost interrupt than a crashing machine. Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Alexey Brodkin authored
commit f51e2f19 upstream. Currently instruction_pointer() returns pt_regs->ret and so return value is of type "long", which implicitly stands for "signed long". While that's perfectly fine when dealing with 32-bit values if return value of instruction_pointer() gets assigned to 64-bit variable sign extension may happen. And at least in one real use-case it happens already. In perf_prepare_sample() return value of perf_instruction_pointer() (which is an alias to instruction_pointer() in case of ARC) is assigned to (struct perf_sample_data)->ip (which type is "u64"). And what we see if instuction pointer points to user-space application that in case of ARC lays below 0x8000_0000 "ip" gets set properly with leading 32 zeros. But if instruction pointer points to kernel address space that starts from 0x8000_0000 then "ip" is set with 32 leadig "f"-s. I.e. id instruction_pointer() returns 0x8100_0000, "ip" will be assigned with 0xffff_ffff__8100_0000. Which is obviously wrong. In particular that issuse broke output of perf, because perf was unable to associate addresses like 0xffff_ffff__8100_0000 with anything from /proc/kallsyms. That's what we used to see: ----------->8---------- 6.27% ls [unknown] [k] 0xffffffff8046c5cc 2.96% ls libuClibc-0.9.34-git.so [.] memcpy 2.25% ls libuClibc-0.9.34-git.so [.] memset 1.66% ls [unknown] [k] 0xffffffff80666536 1.54% ls libuClibc-0.9.34-git.so [.] 0x000224d6 1.18% ls libuClibc-0.9.34-git.so [.] 0x00022472 ----------->8---------- With that change perf output looks much better now: ----------->8---------- 8.21% ls [kernel.kallsyms] [k] memset 3.52% ls libuClibc-0.9.34-git.so [.] memcpy 2.11% ls libuClibc-0.9.34-git.so [.] malloc 1.88% ls libuClibc-0.9.34-git.so [.] memset 1.64% ls [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore 1.41% ls [kernel.kallsyms] [k] __d_lookup_rcu ----------->8---------- Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: arc-linux-dev@synopsys.com Cc: linux-kernel@vger.kernel.org Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Martin Schwidefsky authored
commit f9c87a6f upstream. If the kernel is compiled with gcc 5.1 and the XZ compression option the decompress_kernel function calls _sclp_print_early in 64-bit mode while the content of the upper register half of %r6 is non-zero. This causes a specification exception on the servc instruction in _sclp_servc. The _sclp_print_early function saves and restores the upper registers halves but it fails to clear them for the 31-bit code of the mini sclp driver. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Al Viro authored
commit 75a6f82a upstream. Normally opening a file, unlinking it and then closing will have the inode freed upon close() (provided that it's not otherwise busy and has no remaining links, of course). However, there's one case where that does *not* happen. Namely, if you open it by fhandle with cold dcache, then unlink() and close(). In normal case you get d_delete() in unlink(2) notice that dentry is busy and unhash it; on the final dput() it will be forcibly evicted from dcache, triggering iput() and inode removal. In this case, though, we end up with *two* dentries - disconnected (created by open-by-fhandle) and regular one (used by unlink()). The latter will have its reference to inode dropped just fine, but the former will not - it's considered hashed (it is on the ->s_anon list), so it will stay around until the memory pressure will finally do it in. As the result, we have the final iput() delayed indefinitely. It's trivial to reproduce - void flush_dcache(void) { system("mount -o remount,rw /"); } static char buf[20 * 1024 * 1024]; main() { int fd; union { struct file_handle f; char buf[MAX_HANDLE_SZ]; } x; int m; x.f.handle_bytes = sizeof(x); chdir("/root"); mkdir("foo", 0700); fd = open("foo/bar", O_CREAT | O_RDWR, 0600); close(fd); name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0); flush_dcache(); fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR); unlink("foo/bar"); write(fd, buf, sizeof(buf)); system("df ."); /* 20Mb eaten */ close(fd); system("df ."); /* should've freed those 20Mb */ flush_dcache(); system("df ."); /* should be the same as #2 */ } will spit out something like Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 303843 1131 100% / Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 303843 1131 100% / Filesystem 1K-blocks Used Available Use% Mounted on /dev/root 322023 283282 21692 93% / - inode gets freed only when dentry is finally evicted (here we trigger than by remount; normally it would've happened in response to memory pressure hell knows when). Acked-by: J. Bruce Fields <bfields@fieldses.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Kirill A. Shutemov authored
commit 6b7339f4 upstream. Reading page fault handler code I've noticed that under right circumstances kernel would map anonymous pages into file mappings: if the VMA doesn't have vm_ops->fault() and the VMA wasn't fully populated on ->mmap(), kernel would handle page fault to not populated pte with do_anonymous_page(). Let's change page fault handler to use do_anonymous_page() only on anonymous VMA (->vm_ops == NULL) and make sure that the VMA is not shared. For file mappings without vm_ops->fault() or shred VMA without vm_ops, page fault on pte_none() entry would lead to SIGBUS. Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
- 06 Aug, 2015 2 commits
-
-
Herton R. Krzesinski authored
commit 7250dc3f upstream. I received a report from an user of following mouse which needs this quirk: usb 1-1.6: USB disconnect, device number 58 usb 1-1.6: new low speed USB device number 59 using ehci_hcd usb 1-1.6: New USB device found, idVendor=04f2, idProduct=1053 usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-1.6: Product: USB Optical Mouse usb 1-1.6: Manufacturer: PixArt usb 1-1.6: configuration #1 chosen from 1 choice input: PixArt USB Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input5887 generic-usb 0003:04F2:1053.16FE: input,hidraw2: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:00:1a.0-1.6/input0 The quirk was tested by the reporter and it fixed the frequent disconnections etc. [jkosina@suse.cz: reorder the position in hid-ids.h] Signed-off-by: Herton R. Krzesinski <herton@redhat.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Oliver Neukum <ONeukum@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Brian Silverman authored
commit 30a6b803 upstream. free_pi_state and exit_pi_state_list both clean up futex_pi_state's. exit_pi_state_list takes the hb lock first, and most callers of free_pi_state do too. requeue_pi doesn't, which means free_pi_state can free the pi_state out from under exit_pi_state_list. For example: task A | task B exit_pi_state_list | pi_state = | curr->pi_state_list->next | | futex_requeue(requeue_pi=1) | // pi_state is the same as | // the one in task A | free_pi_state(pi_state) | list_del_init(&pi_state->list) | kfree(pi_state) list_del_init(&pi_state->list) | Move the free_pi_state calls in requeue_pi to before it drops the hb locks which it's already holding. [ tglx: Removed a pointless free_pi_state() call and the hb->lock held debugging. The latter comes via a seperate patch ] Signed-off-by: Brian Silverman <bsilver16384@gmail.com> Cc: austin.linux@gmail.com Cc: darren@dvhart.com Cc: peterz@infradead.org Cc: Mike Galbraith <mgalbraith@suse.de> Link: http://lkml.kernel.org/r/1414282837-23092-1-git-send-email-bsilver16384@gmail.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
- 05 Aug, 2015 1 commit
-
-
Fupan Li authored
3.12 commit 065487a1 ("x86/efi: Correct EFI boot stub use of code32_start"), upstream commit 7e8213c1 imported a bug, which will cause 32bit kernel boot to fail using EFI method. It should use the label's address instead of the value stored in the label to calculate the address of code32_start. Signed-off-by: Fupan Li <fupan.li@windriver.com> Reviewed-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
- 04 Aug, 2015 19 commits
-
-
Jiri Slaby authored
-
Al Viro authored
commit 451a2886 upstream. unfortunately, allowing an arbitrary 16bit value means a possibility of overflow in the calculation of total number of pages in bio_map_user_iov() - we rely on there being no more than PAGE_SIZE members of sum in the first loop there. If that sum wraps around, we end up allocating too small array of pointers to pages and it's easy to overflow it in the second loop. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> [bwh: s/MAX_UIOVEC/UIO_MAXIOV/. This was fixed upstream by commit fdc81f45 ("sg_start_req(): use import_iovec()"), but we don't have that function.] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Chad Dupuis authored
commit ef86cb20 upstream. Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Linus Torvalds authored
commit 6f957724 upstream. The firmware class uevent function accessed the "fw_priv->buf" buffer without the proper locking and testing for NULL. This is an old bug (looks like it goes back to 2012 and commit 1244691c: "firmware loader: introduce firmware_buf"), but for some reason it's triggering only now in 4.2-rc1. Shuah Khan is trying to bisect what it is that causes this to trigger more easily, but in the meantime let's just fix the bug since others are hitting it too (at least Ingo reports having seen it as well). Reported-and-tested-by: Shuah Khan <shuahkh@osg.samsung.com> Acked-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Joe Perches authored
commit a28e4b2b upstream. Removing unnecessary static buffers is good. Use the vsprintf %pV extension instead. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Mikulas Patocka <mikulas@twibright.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Christoffer Dall authored
commit fd28f5d4 upstream. The current pmd_huge() and pud_huge() functions simply check if the table bit is not set and reports the entries as huge in that case. This is counter-intuitive as a clear pmd/pud cannot also be a huge pmd/pud, and it is inconsistent with at least arm and x86. To prevent others from making the same mistake as me in looking at code that calls these functions and to fix an issue with KVM on arm64 that causes memory corruption due to incorrect page reference counting resulting from this mistake, let's change the behavior. Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Reviewed-by: Steve Capper <steve.capper@linaro.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Fixes: 084bd298 ("ARM64: mm: HugeTLB support.") Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Chris Wilson authored
commit 8b572a42 upstream. In needs_ilk_vtd_wa(), we pass in the GPU device but compared it against the ids for the mobile GPU and the mobile host bridge. That latter is impossible and so likely was just a typo for the desktop GPU device id (which is also buggy). Fixes commit da88a5f7 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Wed Feb 13 09:31:53 2013 +0000 drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK Reported-by: Ting-Wei Lan <lantw44@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91127 References: https://bugzilla.freedesktop.org/show_bug.cgi?id=60391Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Ilya Dryomov authored
commit 5a60e876 upstream. rbd_obj_request_create() is called on the main I/O path, so we need to use GFP_NOIO to make sure allocation doesn't blow back on us. Not all callers need this, but I'm still hardcoding the flag inside rather than making it a parameter because a) this is going to stable, and b) those callers shouldn't really use rbd_obj_request_create() and will be fixed in the future. More memory allocation fixes will follow. Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Al Viro authored
commit 0a73d0a2 upstream. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Al Viro authored
commit a84b69cb upstream. If we'd already sent a request and decide to abort it, we *must* issue TFLUSH properly and not just blindly reuse the tag, or we'll get seriously screwed when response eventually arrives and we confuse it for response to later request that had reused the same tag. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Trond Myklebust authored
commit 88de6af2 upstream. req->rq_private_buf isn't initialised when xprt_setup_backchannel calls xprt_free_allocation. Fixes: fb7a0b9a ("nfs41: New backchannel helper routines") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Jeff Layton authored
commit 764ad8ba upstream. The current buffer is much too small if you have a relatively long hostname. Bring it up to the size of the one that SETCLIENTID has. Reported-by: Michael Skralivetsky <michael.skralivetsky@primarydata.com> Signed-off-by: Jeff Layton <jeff.layton@primarydata.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Olga Kornievskaia authored
commit e8d975e7 upstream. Problem: When an operation like WRITE receives a BAD_STATEID, even though recovery code clears the RECLAIM_NOGRACE recovery flag before recovering the open state, because of clearing delegation state for the associated inode, nfs_inode_find_state_and_recover() gets called and it makes the same state with RECLAIM_NOGRACE flag again. As a results, when we restart looking over the open states, we end up in the infinite loop instead of breaking out in the next test of state flags. Solution: unset the RECLAIM_NOGRACE set because of calling of nfs_inode_find_state_and_recover() after returning from calling recover_open() function. Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Chuck Lever authored
commit d683cc49 upstream. When encoding the NFSACL SETACL operation, reserve just the estimated size of the ACL rather than a fixed maximum. This eliminates needless zero padding on the wire that the server ignores. Fixes: ee5dc773 ('NFS: Fix "kernel BUG at fs/nfs/nfs3xdr.c:1338!"') Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Uwe Kleine-König authored
commit 530c11d4 upstream. The omap watchdog has the annoying behaviour that writes to most registers don't have any effect when the watchdog is already running. Quoting the AM335x reference manual: To modify the timer counter value (the WDT_WCRR register), prescaler ratio (the WDT_WCLR[4:2] PTV bit field), delay configuration value (the WDT_WDLY[31:0] DLY_VALUE bit field), or the load value (the WDT_WLDR[31:0] TIMER_LOAD bit field), the watchdog timer must be disabled by using the start/stop sequence (the WDT_WSPR register). Currently the timer is stopped in the .probe callback but still there are possibilities that yield to a situation where omap_wdt_start is entered with the timer running (e.g. when /dev/watchdog is closed without stopping and then reopened). In such a case programming the timeout silently fails! To circumvent this stop the timer before reprogramming. Assuming one of the first things the watchdog user does is setting the timeout explicitly nothing too bad should happen because this explicit setting works fine. Fixes: 7768a13c ("[PATCH] OMAP: Add Watchdog driver support") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Alan Stern authored
commit 3f2cee73 upstream. The usbfs API has a peculiar hole: Users are not allowed to reap their URBs after the device has been disconnected. There doesn't seem to be any good reason for this; it is an ad-hoc inconsistency. The patch allows users to issue the USBDEVFS_REAPURB and USBDEVFS_REAPURBNDELAY ioctls (together with their 32-bit counterparts on 64-bit systems) even after the device is gone. If no URBs are pending for a disconnected device then the ioctls will return -ENODEV rather than -EAGAIN, because obviously no new URBs will ever be able to complete. The patch also adds a new capability flag for USBDEVFS_GET_CAPABILITIES to indicate that the reap-after-disconnect feature is supported. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Chris Dickens <christopher.a.dickens@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Pali Rohár authored
commit b8830a4e upstream. This commit fix kernel crash when probing for rfkill devices in dell-laptop driver failed. Function free_page() was incorrectly used on struct page * instead of virtual address of SMI buffer. This commit also simplify allocating page for SMI buffer by using __get_free_page() function instead of sequential call of functions alloc_page() and page_address(). Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Acked-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Arnd Bergmann authored
commit 4b200b46 upstream. This fixes a several year old regression that I found while trying to get the Yoga 3 11 to work. The ideapad_rfk_set function is meant to send a command to the embedded controller through ACPI, but as of c1f73658, it sends the index of the rfkill device instead of the command, and ignores the opcode field. This changes it back to the original behavior, which indeed flips the rfkill state as seen in the debugfs interface. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: c1f73658 ("ideapad: pass ideapad_priv as argument (part 2)") Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Damian Eppel authored
commit 56a94f13 upstream. Whilst testing cpu hotplug events on kernel configured with DEBUG_PREEMPT and DEBUG_ATOMIC_SLEEP we get following BUG message, caused by calling request_irq() and free_irq() in the context of hotplug notification (which is in this case atomic context). [ 40.785859] CPU1: Software reset [ 40.786660] BUG: sleeping function called from invalid context at mm/slub.c:1241 [ 40.786668] in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/1 [ 40.786678] Preemption disabled at:[< (null)>] (null) [ 40.786681] [ 40.786692] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.19.0-rc4-00024-g7dca860 #36 [ 40.786698] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) [ 40.786728] [<c0014a00>] (unwind_backtrace) from [<c0011980>] (show_stack+0x10/0x14) [ 40.786747] [<c0011980>] (show_stack) from [<c0449ba0>] (dump_stack+0x70/0xbc) [ 40.786767] [<c0449ba0>] (dump_stack) from [<c00c6124>] (kmem_cache_alloc+0xd8/0x170) [ 40.786785] [<c00c6124>] (kmem_cache_alloc) from [<c005d6f8>] (request_threaded_irq+0x64/0x128) [ 40.786804] [<c005d6f8>] (request_threaded_irq) from [<c0350b8c>] (exynos4_local_timer_setup+0xc0/0x13c) [ 40.786820] [<c0350b8c>] (exynos4_local_timer_setup) from [<c0350ca8>] (exynos4_mct_cpu_notify+0x30/0xa8) [ 40.786838] [<c0350ca8>] (exynos4_mct_cpu_notify) from [<c003b330>] (notifier_call_chain+0x44/0x84) [ 40.786857] [<c003b330>] (notifier_call_chain) from [<c0022fd4>] (__cpu_notify+0x28/0x44) [ 40.786873] [<c0022fd4>] (__cpu_notify) from [<c0013714>] (secondary_start_kernel+0xec/0x150) [ 40.786886] [<c0013714>] (secondary_start_kernel) from [<40008764>] (0x40008764) Interrupts cannot be requested/freed in the CPU_STARTING/CPU_DYING notifications which run on the hotplugged cpu with interrupts and preemption disabled. To avoid the issue, request the interrupts for all possible cpus in the boot code. The interrupts are marked NO_AUTOENABLE to avoid a racy request_irq/disable_irq() sequence. The flag prevents the request_irq() code from enabling the interrupt immediately. The interrupt is then enabled in the CPU_STARTING notifier of the hotplugged cpu and again disabled with disable_irq_nosync() in the CPU_DYING notifier. [ tglx: Massaged changelog to match the patch ] Fixes: 7114cd74 ("clocksource: exynos_mct: use (request/free)_irq calls for local timer registration") Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Tested-by: Marcin Jabrzyk <m.jabrzyk@samsung.com> Signed-off-by: Damian Eppel <d.eppel@samsung.com> Cc: m.szyprowski@samsung.com Cc: kyungmin.park@samsung.com Cc: daniel.lezcano@linaro.org Cc: kgene@kernel.org Cc: linux-arm-kernel@lists.infradead.org Link: http://lkml.kernel.org/r/1435324984-7328-1-git-send-email-d.eppel@samsung.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-