Replace use of magic number with recently introduced define.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Ioana Ciornei says:

====================
net: phy: add support for shared interrupts (part 3)

This patch set aims to actually add support for shared interrupts in
phylib and not only for multi-PHY devices. While we are at it,
streamline the interrupt handling in phylib.

For a bit of context, at the moment, there are multiple phy_driver ops
that deal with this subject:

- .config_intr() - Enable/disable the interrupt line.

- .ack_interrupt() - Should quiesce any interrupts that may have been
  fired.  It's also used by phylib in conjunction with .config_intr() to
  clear any pending interrupts after the line was disabled, and before
  it is going to be enabled.

- .did_interrupt() - Intended for multi-PHY devices with a shared IRQ
  line and used by phylib to discern which PHY from the package was the
  one that actually fired the interrupt.

- .handle_interrupt() - Completely overrides the default interrupt
  handling logic from phylib. The PHY driver is responsible for checking
  if any interrupt was fired by the respective PHY and choose
  accordingly if it's the one that should trigger the link state machine.

From my point of view, the interrupt handling in phylib has become
somewhat confusing with all these callbacks that actually read the same
PHY register - the interrupt status.  A more streamlined approach would
be to just move the responsibility to write an interrupt handler to the
driver (as any other device driver does) and make .handle_interrupt()
the only way to deal with interrupts.

Another advantage with this approach would be that phylib would gain
support for shared IRQs between different PHY (not just multi-PHY
devices), something which at the moment would require extending every
PHY driver anyway in order to implement their .did_interrupt() callback
and duplicate the same logic as in .ack_interrupt(). The disadvantage
of making .did_interrupt() mandatory would be that we are slightly
changing the semantics of the phylib API and that would increase
confusion instead of reducing it.

What I am proposing is the following:

- As a first step, make the .ack_interrupt() callback optional so that
  we do not break any PHY driver amid the transition.

- Every PHY driver gains a .handle_interrupt() implementation that, for
  the most part, would look like below:

	irq_status = phy_read(phydev, INTR_STATUS);
	if (irq_status < 0) {
		phy_error(phydev);
		return IRQ_NONE;
	}

	if (!(irq_status & irq_mask))
		return IRQ_NONE;

	phy_trigger_machine(phydev);

	return IRQ_HANDLED;

- Remove each PHY driver's implementation of the .ack_interrupt() by
  actually taking care of quiescing any pending interrupts before
  enabling/after disabling the interrupt line.

- Finally, after all drivers have been ported, remove the
  .ack_interrupt() and .did_interrupt() callbacks from phy_driver.

This patch set is part 3 (and final) of the entire change set and it
addresses the remaining PHY drivers that have not been migrated
previosly. Also, it finally removed the .did_interrupt() and
.ack_interrupt() callbacks since they are of no use anymore.

I do not have access to most of these PHY's, therefore I Cc-ed the
latest contributors to the individual PHY drivers in order to have
access, hopefully, to more regression testing.
====================

Link: https://lore.kernel.org/r/20201123153817.1616814-1-ciorneiioana@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.

With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Also, add a comment describing the multiple step interrupt
acknoledgement process.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Mathias Kresin <dev@kresin.me>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Mathias Kresin <dev@kresin.me>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The driver's ISR sends a 'software interrupt' event to the probe()
thread using the following method:
- probe(): write 0 to flag, enable s/w interrupt
- probe(): poll on flag, relax using usleep_range()
- ISR    : write 1 to flag

Replace with wake_up() / wait_event_timeout(). Besides being easier
to get right, this abstraction has better timing and memory
consistency properties.

Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201123191529.14908-2-TheSven73@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

For no apparent reason, this function reads the INT_STS register, and
checks if the software interrupt bit is set. These things have already
been carried out by this function's only caller.

Clean up by removing the redundant code.

Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201123191529.14908-1-TheSven73@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Lorenzo Bianconi says:

====================
mvneta: access skb_shared_info only on last frag

Build skb_shared_info on mvneta_rx_swbm stack and sync it to xdp_buff
skb_shared_info area only on the last fragment.
Avoid avoid unnecessary xdp_buff initialization in mvneta_rx_swbm routine.
This a preliminary series to complete xdp multi-buff in mvneta driver.
====================

Link: https://lore.kernel.org/r/cover.1605889258.git.lorenzo@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Build skb_shared_info on mvneta_rx_swbm stack and sync it to xdp_buff
skb_shared_info area only on the last fragment. Leftover cache miss in
mvneta_swbm_rx_frame will be addressed introducing mb bit in
xdp_buff/xdp_frame struct
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pass skb_shared_info pointer from mvneta_xdp_put_buff caller. This is a
preliminary patch to reduce accesses to skb_shared_info area and reduce
cache misses.
Remove napi parameter in mvneta_xdp_put_buff signature since it is always
run in NAPI context
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Explicitly initialize mandatory fields defining xdp_buff struct
in mvneta_rx_swbm routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Tx/Rx FIFO is a HW resource limited by total size, but shared
by all ports of same CP110 and impacting port-performance.
Do not divide the FIFO for ports which are not enabled in DTS,
so active ports could have more FIFO.
No change in FIFO allocation if all 3 ports on the communication
processor enabled in DTS.

The active port mapping should be done in probe before FIFO-init.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/1606154073-28267-1-git-send-email-stefanc@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Introduce page_pool_put_page_bulk() entry into the API section of
page_pool.rst
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a6a5141b4d7b7b71fa7778b16b48f80095dd3233.1606146163.git.lorenzo@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In bug report [0] a warning in r8169 driver was reported that was
caused by an invalid GSO SKB (gso_type was 0). See [1] for a discussion
about this issue. Still the origin of the invalid GSO SKB isn't clear.

It shouldn't be a network drivers task to check for invalid GSO SKB's.
Also, even if issue [0] can be fixed, we can't be sure that a
similar issue doesn't pop up again at another place.
Therefore let gso_features_check() check for such invalid GSO SKB's.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=209423
[1] https://www.spinics.net/lists/netdev/msg690794.htmlSigned-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/97c78d21-7f0b-d843-df17-3589f224d2cf@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There are spelling mistakes in two dev_err messages. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201123103452.197708-1-colin.king@canonical.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ido Schimmel says:

====================
mlxsw: Add support for blackhole nexthops

This patch set adds support for blackhole nexthops in mlxsw. These
nexthops are exactly the same as other nexthops, but instead of
forwarding packets to an egress router interface (RIF), they are
programmed to silently drop them.

Patches #1-#4 are preparations.

Patch #5 adds support for blackhole nexthops and removes the check that
prevented them from being programmed.

Patch #6 adds a selftests over mlxsw which tests that blackhole nexthops
can be programmed and are marked as offloaded.

Patch #7 extends the existing nexthop forwarding test to also test
blackhole functionality.

Patches #8-#10 add support for a new packet trap ('blackhole_nexthop')
which should be triggered whenever packets are dropped by a blackhole
nexthop. Obviously, by default, the trap action is set to 'drop' so that
dropped packets will not be reported.
====================

Link: https://lore.kernel.org/r/20201123071230.676469-1-idosch@idosch.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Test that packets hitting a blackhole nexthop are trapped to the CPU
when the trap is enabled. Test that packets are not reported when the
trap is disabled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Register with devlink the blackhole_nexthop trap so that mlxsw will be
able to report packets dropped due to a blackhole nexthop.

The internal trap identifier is "DISCARD_ROUTER3", which traps packets
dropped in the adjacency table.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a packet trap to report packets that were dropped due to a
blackhole nexthop.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Test that IPv4 and IPv6 ping fail when the route is using a blackhole
nexthop or a group with a blackhole nexthop. Test that ping passes when
the route starts using a valid nexthop.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Test the mlxsw allows blackhole nexthops to be installed and that the
nexthops are marked as offloaded.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for blackhole nexthops by programming them to the adjacency
table with a discard action.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The two are the same, but for blackhole nexthops we will not have an
associated neighbour struct, so resolve the RIF from the nexthop struct
itself instead.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Now that the driver creates a loopback RIF during its initialization, it
can be used to program the adjacency entries for unresolved nexthops
instead of other RIFs. The loopback RIF is guaranteed to exist for the
entire life time of the driver, unlike other RIFs that come and go.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Unresolved nexthops are currently written to the adjacency table with a
discard action. Packets hitting such entries are trapped to the CPU via
the 'DISCARD_ROUTER3' trap which can be enabled or disabled on demand,
but is always enabled in order to ensure the kernel can resolve the
unresolved neighbours.

This trap will be needed for blackhole nexthops support. Therefore, move
unresolved nexthops to explicitly program the adjacency entries with a
trap action and a different trap identifier, 'RTR_EGRESS0'.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Up until now RIFs (router interfaces) were created on demand (e.g.,
when an IP address was added to a netdev). However, sometimes the device
needs to be provided with a RIF when one might not be available.

For example, adjacency entries that drop packets need to be programmed
with an egress RIF despite the RIF not being used to forward packets.

Create such a RIF during initialization so that it could be used later
on to support blackhole nexthops.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

David Howells says:

====================
rxrpc: Prelude to gssapi support

Here are some patches that do some reorganisation of the security class
handling in rxrpc to allow implementation of the RxGK security class that
will allow AF_RXRPC to use GSSAPI-negotiated tokens and better crypto.  The
RxGK security class is not included in this patchset.

It does the following things:

 (1) Add a keyrings patch to provide the original key description, as
     provided to add_key(), to the payload preparser so that it can
     interpret the content on that basis.  Unfortunately, the rxrpc_s key
     type wasn't written to interpret its payload as anything other than a
     string of bytes comprising a key, but for RxGK, more information is
     required as multiple Kerberos enctypes are supported.

 (2) Remove the rxk5 security class key parsing.  The rxk5 class never got
     rolled out in OpenAFS and got replaced with rxgk.

 (3) Support the creation of rxrpc keys with multiple tokens of different
     types.  If some types are not supported, the ENOPKG error is
     suppressed if at least one other token's type is supported.

 (4) Punt the handling of server keys (rxrpc_s type) to the appropriate
     security class.

 (5) Organise the security bits in the rxrpc_connection struct into a
     union to make it easier to override for other classes.

 (6) Move some bits from core code into rxkad that won't be appropriate to
     rxgk.

* tag 'rxrpc-next-20201123' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  rxrpc: Ask the security class how much space to allow in a packet
  rxrpc: rxkad: Don't use pskb_pull() to advance through the response packet
  rxrpc: Organise connection security to use a union
  rxrpc: Don't reserve security header in Tx DATA skbuff
  rxrpc: Merge prime_packet_security into init_connection_security
  rxrpc: Fix example key name in a comment
  rxrpc: Ignore unknown tokens in key payload unless no known tokens
  rxrpc: Make the parsing of xdr payloads more coherent
  rxrpc: Allow security classes to give more info on server keys
  rxrpc: Don't leak the service-side session key to userspace
  rxrpc: Hand server key parsing off to the security class
  rxrpc: Split the server key type (rxrpc_s) into its own file
  rxrpc: Don't retain the server key in the connection
  rxrpc: Support keys with multiple authentication tokens
  rxrpc: List the held token types in the key description in /proc/keys
  rxrpc: Remove the rxk5 security class as it's now defunct
  keys: Provide the original description to the key preparser
====================

Link: https://lore.kernel.org/r/160616220405.830164.2239716599743995145.stgit@warthog.procyon.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This driver uses a normal timer for TX coalescing, which means that the
with the default tx-usecs of 1000 microseconds the cleanups actually
happen 10 ms or more later with HZ=100.  This leads to very low
througput with TCP when bridged to a slow link such as a 4G modem.  Fix
this by using an hrtimer instead.

On my ARM platform with HZ=100 and the default TX coalescing settings
(tx-frames 25 tx-usecs 1000), with "tc qdisc add dev eth0 root netem
delay 60ms 40ms rate 50Mbit" run on the server, netperf's TCP_STREAM
improves from ~5.5 Mbps to ~100 Mbps.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20201120150208.6838-1-vincent.whitchurch@axis.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>