- 22 Jul, 2020 5 commits
-
-
Alexandru Ardelean authored
There are 2 exit paths where the lock isn't held, but try to unlock the mutex when exiting. In these places we should just return from the function. A neater approach would be to cleanup the ad5592r_read_raw(), but that would make this patch more difficult to backport to stable versions. Fixes 56ca9db8: ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs") Reported-by:
Charles Stanhope <charles.stanhope@gmail.com> Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Jonathan Cameron authored
Series needed as base for a clocksource tree hence immutable branch
-
Jonathan Cameron authored
Immutable branch may be needed in input for a joystick set that is dependent on it.
-
Alexandru Ardelean authored
This was introduced initially via commit 78289b4a ("iio: core: pass parent device as parameter during allocation"), but was accidentally removed via commit 6d4ebd56 ("iio: core: wrap IIO device into an iio_dev_opaque object"). This looks like a rebase gone wrong, and ends up breaking devicetree bindings of IIO clients. This change adds back the parent assignment. Fixes 6d4ebd56: ("iio: core: wrap IIO device into an iio_dev_opaque object") Reported-by:
Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by:
-
Alexandru Ardelean authored
This change does the following: * removes the SPI device table in favor of the OF device table * adds 'name' && 'chip_id' fields to chip_info * implements chip ID & silicon revision checking; the device ID for AD7124-4 is 0x0, so just checking that value can be useless; but at least the silicon revision isn't 0, so a non-zero value can be used to check that "a" device is on the SPI bus; it's probably the best way to narrow it down to one of the 2 AD7124 chip IDs Signed-off-by:
-
- 20 Jul, 2020 35 commits
-
-
Kamel Bouhara authored
This drivers allows to use the capture mode of the Timer Counter Block hardware block available in Microchip SoCs through the counter subsystem. Two functions of the counter are supported for the moment: period capture and quadrature decoder. The latter is only supported by the SAMA5 series of SoCs. For the period capture mode a basic setup has been chosen that will reset the counter each time the period is actually reached. Of course the device offers much more possibilities. For quadrature mode, both channel 0 and 1 must be configured even if we only capture the position (no revolution/rotation). Signed-off-by:
Kamel Bouhara <kamel.bouhara@bootlin.com> Signed-off-by:
-
Kamel Bouhara authored
Describe the devicetree binding for the Microchip TCB module. Each counter blocks exposes three independent counters. However, when configured in quadrature decoder, both channel <0> and <1> are required for speed/position and rotation capture (yet only the position is captured). Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Alexandre Belloni authored
The sama5d2 TC block TIMER_CLOCK1 is different from the at91sam9x5 one. Instead of being MCK / 2, it is the TCB GCLK. Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Alexandre Belloni authored
Convert Atmel Timer Counter Blocks bindings to DT schema format using json-schema. Also move it out of mfd as it is not and has never been related to mfd. Signed-off-by:
-
Kamel Bouhara authored
Some atmel socs have extra tcb capabilities that allow using a generic clock source or enabling a quadrature decoder. Signed-off-by:
-
Artur Rojek authored
The SADC component in JZ47xx SoCs provides support for touchscreen operations (pen position and pen down pressure) in single-ended and differential modes. The touchscreen component of SADC takes a significant time to stabilize after first receiving the clock and a delay of 50ms has been empirically proven to be a safe value before data sampling can begin. Of the known hardware to use this controller, GCW Zero and Anbernic RG-350 utilize the touchscreen mode by having their joystick(s) attached to the X/Y positive/negative input pins. JZ4770 and later SoCs introduce a low-level command feature. With it, up to 32 commands can be programmed, each one corresponding to a sampling job. It allows to change the low-voltage reference, the high-voltage reference, have them connected to VCC, GND, or one of the X-/X+ or Y-/Y+ pins. This patch introduces support for 6 stream-capable channels: - channel #0 samples X+/GND - channel #1 samples Y+/GND - channel #2 samples X-/GND - channel #3 samples Y-/GND - channel #4 samples X+/X- - channel #5 samples Y+/Y- Being able to sample X-/GND and Y-/GND is useful on some devices, where one joystick is connected to the X+/Y+ pins, and a second joystick is connected to the X-/Y- pins. All the boards which probe this driver have the interrupt provided from Device Tree, with no need to handle a case where the IRQ was not provided. Co-developed-by:
Paul Cercueil <paul@crapouillou.net> Signed-off-by:
Artur Rojek <contact@artur-rojek.eu> Signed-off-by:
-
Artur Rojek authored
Introduce support for touchscreen channels found in JZ47xx SoCs. Signed-off-by:
-
Paul Cercueil authored
Instead of having one array of struct iio_chan_spec for all SoCs, and have some SoCs remove the last item of the array as they can't use it, have each SoC define its array of supported channels. Signed-off-by:
-
Artur Rojek authored
Provide an of_xlate callback in order to retrieve the correct channel specifier index from the IIO channels array. Signed-off-by:
-
Artur Rojek authored
Introduce error checks for the clk_enable calls used in this driver. As part of the changes, move clk_enable/clk_disable calls out of ingenic_adc_set_config and into respective logic of its callers. Signed-off-by:
-
Jonathan Cameron authored
Fairly simple binding. Most of the changes were filling in information not previously found in the binding. I dropped the previous explicit mention of spi-max-frequency as that is covered by the generic SPI binding. Signed-off-by:
Sean Nyekjaer <sean@geanix.com> Reviewed-by:
-
Icenowy Zheng authored
The STK3311 chip has a variant called STK3311-X, which has a different chip id of 0x12. Add the chip id to the driver. Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Signed-off-by:
Ondrej Jirman <megous@megous.com> Signed-off-by:
-
Jonathan Cameron authored
Convert and flesh out a bit the binding docs for this simple 3 axis accelerometer. Signed-off-by:
-
Alexandru Ardelean authored
The change is more cosmetic. There is no need to reference this table in the probe function since 'of_device_get_match_data' is used, which obtains this information from the driver object. Signed-off-by:
-
Lee Jones authored
This is the only use of kerneldoc in the source file and no descriptions are provided. Fixes the following W=1 kernel build warning(s): drivers/iio/adc/rockchip_saradc.c:190: warning: Function parameter or member 'reset' not described in 'rockchip_saradc_reset_controller' Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: linux-rockchip@lists.infradead.org Signed-off-by:
Lee Jones <lee.jones@linaro.org> Reviewed-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Lee Jones authored
It doesn't make sense to move it into '*core*' as it's co-located with other, similar definitions which are used in multiple locations. Fixes the following W=1 kernel build warning(s): In file included from drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i2c.c:17: drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h:497:44: warning: ‘st_lsm6dsx_accel_ext_info’ defined but not used [-Wunused-const-variable=] 497 | static const struct iio_chan_spec_ext_info st_lsm6dsx_accel_ext_info[] = { | ^~~~~~~~~~~~~~~~~~~~~~~~~ In file included from drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_spi.c:17: drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h:497:44: warning: ‘st_lsm6dsx_accel_ext_info’ defined but not used [-Wunused-const-variable=] 497 | static const struct iio_chan_spec_ext_info st_lsm6dsx_accel_ext_info[] = { | ^~~~~~~~~~~~~~~~~~~~~~~~~ In file included from drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i3c.c:16: drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h:497:44: warning: ‘st_lsm6dsx_accel_ext_info’ defined but not used [-Wunused-const-variable=] 497 | static const struct iio_chan_spec_ext_info st_lsm6dsx_accel_ext_info[] = { | ^~~~~~~~~~~~~~~~~~~~~~~~~ Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Cc: Denis Ciocca <denis.ciocca@st.com> Signed-off-by: -
Lee Jones authored
iio: imu: st_lsm6dsx: st_lsm6dsx_shub: Demote obvious misuse of kerneldoc to standard comment blocks No attempt has been made to document any of the demoted functions here. Fixes the following W=1 kernel build warning(s): drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:174: warning: Function parameter or member 'hw' not described in 'st_lsm6dsx_shub_read_output' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:174: warning: Function parameter or member 'data' not described in 'st_lsm6dsx_shub_read_output' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:174: warning: Function parameter or member 'len' not described in 'st_lsm6dsx_shub_read_output' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:205: warning: Function parameter or member 'hw' not described in 'st_lsm6dsx_shub_write_reg' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:205: warning: Function parameter or member 'addr' not described in 'st_lsm6dsx_shub_write_reg' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:205: warning: Function parameter or member 'data' not described in 'st_lsm6dsx_shub_write_reg' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:205: warning: Function parameter or member 'len' not described in 'st_lsm6dsx_shub_write_reg' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:285: warning: Function parameter or member 'sensor' not described in 'st_lsm6dsx_shub_read' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:285: warning: Function parameter or member 'addr' not described in 'st_lsm6dsx_shub_read' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:285: warning: Function parameter or member 'data' not described in 'st_lsm6dsx_shub_read' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:285: warning: Function parameter or member 'len' not described in 'st_lsm6dsx_shub_read' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:335: warning: Function parameter or member 'sensor' not described in 'st_lsm6dsx_shub_write' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:335: warning: Function parameter or member 'addr' not described in 'st_lsm6dsx_shub_write' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:335: warning: Function parameter or member 'data' not described in 'st_lsm6dsx_shub_write' drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:335: warning: Function parameter or member 'len' not described in 'st_lsm6dsx_shub_write' Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by:
-
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/iio/magnetometer/ak8974.c:200: warning: Function parameter or member 'scan' not described in 'ak8974' Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Samu Onkalo <samu.p.onkalo@nokia.com> Signed-off-by:
-
Lee Jones authored
Kerneldoc is only suitable for documenting functions and struct/enums. Fixes the following W=1 kernel build warning(s): drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_INTERNAL' description in 'PM8XXX_CHANNEL_INTERNAL' drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_125V' description in 'PM8XXX_CHANNEL_INTERNAL' drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_INTERNAL_2' description in 'PM8XXX_CHANNEL_INTERNAL' drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_MUXOFF' description in 'PM8XXX_CHANNEL_INTERNAL' drivers/iio/adc/qcom-pm8xxx-xoadc.c:412: warning: Function parameter or member 'variant' not described in 'pm8xxx_xoadc' Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: linux-arm-msm@vger.kernel.org Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Lee Jones authored
This is the only use of kerneldoc in the source file and no descriptions are provided. Fixes the following W=1 kernel build warning(s): drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c:118: warning: Function parameter or member 'irq' not described in 'inv_mpu6050_read_fifo' drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c:118: warning: Function parameter or member 'p' not described in 'inv_mpu6050_read_fifo' Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by:
-
Lee Jones authored
No attempt has been made to document any of the demoted functions here. Fixes the following W=1 kernel build warning(s): drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:444: warning: Function parameter or member 'st' not described in 'inv_mpu6050_set_lpf_regs' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:444: warning: Function parameter or member 'val' not described in 'inv_mpu6050_set_lpf_regs' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:480: warning: Function parameter or member 'indio_dev' not described in 'inv_mpu6050_init_config' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:862: warning: Function parameter or member 'st' not described in 'inv_mpu6050_set_lpf' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:862: warning: Function parameter or member 'rate' not described in 'inv_mpu6050_set_lpf' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:893: warning: Function parameter or member 'dev' not described in 'inv_mpu6050_fifo_rate_store' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:893: warning: Function parameter or member 'attr' not described in 'inv_mpu6050_fifo_rate_store' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:893: warning: Function parameter or member 'buf' not described in 'inv_mpu6050_fifo_rate_store' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:893: warning: Function parameter or member 'count' not described in 'inv_mpu6050_fifo_rate_store' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:954: warning: Function parameter or member 'dev' not described in 'inv_fifo_rate_show' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:954: warning: Function parameter or member 'attr' not described in 'inv_fifo_rate_show' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:954: warning: Function parameter or member 'buf' not described in 'inv_fifo_rate_show' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:975: warning: Function parameter or member 'dev' not described in 'inv_attr_show' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:975: warning: Function parameter or member 'attr' not described in 'inv_attr_show' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:975: warning: Function parameter or member 'buf' not described in 'inv_attr_show' drivers/iio/imu/inv_mpu6050/inv_mpu_core.c:1282: warning: Function parameter or member 'st' not described in 'inv_check_and_setup_chip' Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by:
-
Lee Jones authored
Very few of the struct attributes have been documented here. Fixes the following W=1 kernel build warning(s): drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'dev' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'palmas' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'irq' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'irq_auto_0' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'irq_auto_1' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'adc_info' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'conv_completion' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'wakeup1_data' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'wakeup2_data' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'wakeup1_enable' not described in 'palmas_gpadc' drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'wakeup2_enable' not described in 'palmas_gpadc' Cc: Pradeep Goudagunta <pgoudagunta@nvidia.com> Signed-off-by:
-
Lee Jones authored
No attempt has been made to document any of the demoted structs here. Fixes the following W=1 kernel build warning(s): drivers/iio/adc/max9611.c:117: warning: cannot understand function prototype: 'const unsigned int max9611_mux_conf[][2] = ' drivers/iio/adc/max9611.c:145: warning: cannot understand function prototype: 'const unsigned int max9611_gain_conf[][2] = ' Cc: Jacopo Mondi <jacopo+renesas@jmondi.org> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Lee Jones authored
Kerneldoc expects attributes/parameters to be in '@*.: ' format. Fixes the following W=1 kernel build warning(s): drivers/iio/adc/max1363.c:190: warning: Function parameter or member 'lock' not described in 'max1363_state' Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Rohit Sarkar <rohitsarkar5398@gmail.com> Signed-off-by:
-
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h:487:1: warning: ‘inline’ is not at beginning of declaration [-Wold-style-declaration] drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h:497:44: warning: ‘st_lsm6dsx_accel_ext_info’ defined but not used [-Wunused-const-variable=] Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Cc: Denis Ciocca <denis.ciocca@st.com> Signed-off-by:
-
Lee Jones authored
'fxas21002c_reg_fields' is only used in '*core*', meaning that '*i2c*' and '*spi*' complain of a defined but not used const variable. Let's move it into the source file. Fixes the following W=1 kernel build warning(s): In file included from drivers/iio/gyro/fxas21002c_i2c.c:14: drivers/iio/gyro/fxas21002c.h:79:31: warning: ‘fxas21002c_reg_fields’ defined but not used [-Wunused-const-variable=] 79 | static const struct reg_field fxas21002c_reg_fields[] = { | ^~~~~~~~~~~~~~~~~~~~~ In file included from drivers/iio/gyro/fxas21002c_spi.c:14: drivers/iio/gyro/fxas21002c.h:79:31: warning: ‘fxas21002c_reg_fields’ defined but not used [-Wunused-const-variable=] 79 | static const struct reg_field fxas21002c_reg_fields[] = { | ^~~~~~~~~~~~~~~~~~~~~ Cc: Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by: -
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/iio/accel/sca3000.c:210: warning: Function parameter or member 'mot_det_mult_xz' not described in 'sca3000_chip_info' drivers/iio/accel/sca3000.c:210: warning: Function parameter or member 'mot_det_mult_y' not described in 'sca3000_chip_info' drivers/iio/accel/sca3000.c:871: warning: Function parameter or member 'indio_dev' not described in 'sca3000_read_event_value' drivers/iio/accel/sca3000.c:871: warning: Function parameter or member 'chan' not described in 'sca3000_read_event_value' drivers/iio/accel/sca3000.c:871: warning: Function parameter or member 'type' not described in 'sca3000_read_event_value' drivers/iio/accel/sca3000.c:871: warning: Function parameter or member 'dir' not described in 'sca3000_read_event_value' drivers/iio/accel/sca3000.c:871: warning: Function parameter or member 'info' not described in 'sca3000_read_event_value' drivers/iio/accel/sca3000.c:871: warning: Function parameter or member 'val' not described in 'sca3000_read_event_value' drivers/iio/accel/sca3000.c:871: warning: Function parameter or member 'val2' not described in 'sca3000_read_event_value' drivers/iio/accel/sca3000.c:1110: warning: Function parameter or member 'indio_dev' not described in 'sca3000_read_event_config' drivers/iio/accel/sca3000.c:1110: warning: Function parameter or member 'chan' not described in 'sca3000_read_event_config' drivers/iio/accel/sca3000.c:1110: warning: Function parameter or member 'type' not described in 'sca3000_read_event_config' drivers/iio/accel/sca3000.c:1110: warning: Function parameter or member 'dir' not described in 'sca3000_read_event_config' Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Lee Jones authored
None of the headers demoted here provide any descriptions. Fixes the following W=1 kernel build warning(s): drivers/iio/adc/cpcap-adc.c:100: warning: Function parameter or member 'ato_in' not described in 'cpcap_adc_ato' drivers/iio/adc/cpcap-adc.c:100: warning: Function parameter or member 'atox_in' not described in 'cpcap_adc_ato' drivers/iio/adc/cpcap-adc.c:100: warning: Function parameter or member 'adc_ps_factor_in' not described in 'cpcap_adc_ato' drivers/iio/adc/cpcap-adc.c:100: warning: Function parameter or member 'atox_ps_factor_in' not described in 'cpcap_adc_ato' drivers/iio/adc/cpcap-adc.c:100: warning: Function parameter or member 'ato_out' not described in 'cpcap_adc_ato' drivers/iio/adc/cpcap-adc.c:100: warning: Function parameter or member 'atox_out' not described in 'cpcap_adc_ato' drivers/iio/adc/cpcap-adc.c:100: warning: Function parameter or member 'adc_ps_factor_out' not described in 'cpcap_adc_ato' drivers/iio/adc/cpcap-adc.c:100: warning: Function parameter or member 'atox_ps_factor_out' not described in 'cpcap_adc_ato' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_AD0' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BATTP' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_VBUS' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_AD3' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BPLUS_AD4' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_CHG_ISENSE' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BATTI' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_USB_ID' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_AD8' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_AD9' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_LICELL' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_HV_BATTP' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_TSX1_AD12' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_TSX2_AD13' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_TSY1_AD14' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_TSY2_AD15' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BATTP_PI16' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BATTI_PI17' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_CHANNEL_NUM' not described in enum 'cpcap_adc_channel' drivers/iio/adc/cpcap-adc.c:165: warning: Enum value 'CPCAP_ADC_TIMING_IMM' not described in enum 'cpcap_adc_timing' drivers/iio/adc/cpcap-adc.c:165: warning: Enum value 'CPCAP_ADC_TIMING_IN' not described in enum 'cpcap_adc_timing' drivers/iio/adc/cpcap-adc.c:165: warning: Enum value 'CPCAP_ADC_TIMING_OUT' not described in enum 'cpcap_adc_timing' Cc: Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/iio/adc/at91-sama5d2_adc.c:360: warning: cannot understand function prototype: 'struct at91_adc_dma ' drivers/iio/adc/at91-sama5d2_adc.c:379: warning: cannot understand function prototype: 'struct at91_adc_touch ' Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Lee Jones authored
All lines should start with ' *'. Fixes the following W=1 kernel build warning(s): drivers/iio/adc/at91_adc.c:160: warning: bad line: (Interruptions registers mostly) Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Lee Jones authored
Kerneldoc expects attributes/parameters to be in '@*.: ' format. Fixes the following W=1 kernel build warning(s): drivers/iio/dac/ad5504.c:58: warning: Function parameter or member 'pwr_down_mask' not described in 'ad5504_state' drivers/iio/dac/ad5504.c:58: warning: Function parameter or member 'pwr_down_mode' not described in 'ad5504_state' drivers/iio/dac/ad5504.c:64: warning: cannot understand function prototype: 'enum ad5504_supported_device_ids ' Cc: Michael Hennerich <Michael.Hennerich@analog.com> Signed-off-by:
-
Lee Jones authored
This is the only use of function related kerneldoc in the sourcefile and no descriptions are provided. Fixes the following W=1 kernel build warning(s): drivers/iio/adc/ad799x.c:192: warning: Function parameter or member 'irq' not described in 'ad799x_trigger_handler' drivers/iio/adc/ad799x.c:192: warning: Function parameter or member 'p' not described in 'ad799x_trigger_handler' Cc: Michael Hennerich <Michael.Hennerich@analog.com> Signed-off-by:
-
Lee Jones authored
Kerneldoc expects attributes/parameters to be in '@*.: ' format. Fixes the following W=1 kernel build warning(s): drivers/iio/light/us5182d.c:457: warning: Function parameter or member 'data' not described in 'us5182d_update_dark_th' drivers/iio/light/us5182d.c:457: warning: Function parameter or member 'index' not described in 'us5182d_update_dark_th' drivers/iio/light/us5182d.c:479: warning: Function parameter or member 'data' not described in 'us5182d_apply_scale' drivers/iio/light/us5182d.c:479: warning: Function parameter or member 'index' not described in 'us5182d_apply_scale' Cc: Adriana Reus <adriana.reus@intel.com> Signed-off-by:
-
Lee Jones authored
'*'s are not welcome in kerneldoc parameter names. Fixes the following W=1 kernel build warning(s): drivers/iio/temperature/mlx90632.c:175: warning: Function parameter or member 'data' not described in 'mlx90632_perform_measurement' Signed-off-by:
Crt Mori <cmo@melexis.com> Signed-off-by:
-
Lee Jones authored
No attempt has been made to document any of the demoted functions here Fixes the following W=1 kernel build warning(s): drivers/iio/light/si1145.c:192: warning: Function parameter or member 'data' not described in '__si1145_command_reset' drivers/iio/light/si1145.c:228: warning: Function parameter or member 'data' not described in 'si1145_command' drivers/iio/light/si1145.c:228: warning: Function parameter or member 'cmd' not described in 'si1145_command' drivers/iio/light/si1145.c:1186: warning: Function parameter or member 'trig' not described in 'si1145_trigger_set_state' drivers/iio/light/si1145.c:1186: warning: Function parameter or member 'state' not described in 'si1145_trigger_set_state' Cc: Chuhong Yuan <hslester96@gmail.com> Cc: Dan Leonard <leonard.crestez@intel.com> Signed-off-by:
-
