Fix the display of a few fields in the iBFT NIC attribute structure in
sysfs.

Ensure that, if the DHCP IP address and the subnet mask for the interface
is present in the iBFT NIC structure, the corresponding entries are
created in sysfs tree for the device.  This would hence create the
additional entries in the tree based on the iBFT table and would not
delete any existing entries.
Signed-off-by: Ashutosh Naik <ashutosh.naik@gmail.com>
Cc: Vishnu V <vishnu@chelsio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Avoid setting less than two pages for vm_dirty_bytes: this is necessary to
avoid potential division by 0 (like the following) in get_dirty_limits().

[   49.951610] divide error: 0000 [#1] PREEMPT SMP
[   49.952195] last sysfs file: /sys/devices/pci0000:00/0000:00:01.1/host0/target0:0:0/0:0:0:0/block/sda/uevent
[   49.952195] CPU 1
[   49.952195] Modules linked in: pcspkr
[   49.952195] Pid: 3064, comm: dd Not tainted 2.6.30-rc3 #1
[   49.952195] RIP: 0010:[<ffffffff802d39a9>]  [<ffffffff802d39a9>] get_dirty_limits+0xe9/0x2c0
[   49.952195] RSP: 0018:ffff88001de03a98  EFLAGS: 00010202
[   49.952195] RAX: 00000000000000c0 RBX: ffff88001de03b80 RCX: 28f5c28f5c28f5c3
[   49.952195] RDX: 0000000000000000 RSI: 00000000000000c0 RDI: 0000000000000000
[   49.952195] RBP: ffff88001de03ae8 R08: 0000000000000000 R09: 0000000000000000
[   49.952195] R10: ffff88001ddda9a0 R11: 0000000000000001 R12: 0000000000000001
[   49.952195] R13: ffff88001fbc8218 R14: ffff88001de03b70 R15: ffff88001de03b78
[   49.952195] FS:  00007fe9a435b6f0(0000) GS:ffff8800025d9000(0000) knlGS:0000000000000000
[   49.952195] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   49.952195] CR2: 00007fe9a39ab000 CR3: 000000001de38000 CR4: 00000000000006e0
[   49.952195] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   49.952195] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[   49.952195] Process dd (pid: 3064, threadinfo ffff88001de02000, task ffff88001ddda250)
[   49.952195] Stack:
[   49.952195]  ffff88001fa0de00 ffff88001f2dbd70 ffff88001f9fe800 000080b900000000
[   49.952195]  00000000000000c0 ffff8800027a6100 0000000000000400 ffff88001fbc8218
[   49.952195]  0000000000000000 0000000000000600 ffff88001de03bb8 ffffffff802d3ed7
[   49.952195] Call Trace:
[   49.952195]  [<ffffffff802d3ed7>] balance_dirty_pages_ratelimited_nr+0x1d7/0x3f0
[   49.952195]  [<ffffffff80368f8e>] ? ext3_writeback_write_end+0x9e/0x120
[   49.952195]  [<ffffffff802cc7df>] generic_file_buffered_write+0x12f/0x330
[   49.952195]  [<ffffffff802cce8d>] __generic_file_aio_write_nolock+0x26d/0x460
[   49.952195]  [<ffffffff802cda32>] ? generic_file_aio_write+0x52/0xd0
[   49.952195]  [<ffffffff802cda49>] generic_file_aio_write+0x69/0xd0
[   49.952195]  [<ffffffff80365fa6>] ext3_file_write+0x26/0xc0
[   49.952195]  [<ffffffff803034d1>] do_sync_write+0xf1/0x140
[   49.952195]  [<ffffffff80290d1a>] ? get_lock_stats+0x2a/0x60
[   49.952195]  [<ffffffff80280730>] ? autoremove_wake_function+0x0/0x40
[   49.952195]  [<ffffffff8030411b>] vfs_write+0xcb/0x190
[   49.952195]  [<ffffffff803042d0>] sys_write+0x50/0x90
[   49.952195]  [<ffffffff8022ff6b>] system_call_fastpath+0x16/0x1b
[   49.952195] Code: 00 00 00 2b 05 09 1c 17 01 48 89 c6 49 0f af f4 48 c1 ee 02 48 89 f0 48 f7 e1 48 89 d6 31 d2 48 c1 ee 02 48 0f af 75 d0 48 89 f0 <48> f7 f7 41 8b 95 ac 01 00 00 48 89 c7 49 0f af d4 48 c1 ea 02
[   49.952195] RIP  [<ffffffff802d39a9>] get_dirty_limits+0xe9/0x2c0
[   49.952195]  RSP <ffff88001de03a98>
[   50.096523] ---[ end trace 008d7aa02f244d7b ]---
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Local variable `scan' can overflow on zones which are larger than

	(2G * 4k) / 100 = 80GB.

Making it 64-bit on 64-bit will fix that up.

Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

->real_parent is the parent. ->parent may be the tracer.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

scripts/kernel-doc can (incorrectly) delete struct members that are
surrounded by /* ...  */ <struct members> /* ...  */ if there is a /*
private: */ comment in there somewhere also.

Fix that by making the "/* private:" only allow whitespace between /* and
"private:", not anything/everything in the world.

This fixes some erroneous kernel-doc warnings that popped up while
processing include/linux/usb/composite.h.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The Committed_AS field can underflow in certain situations:

>         # while true; do cat /proc/meminfo  | grep _AS; sleep 1; done | uniq -c
>               1 Committed_AS: 18446744073709323392 kB
>              11 Committed_AS: 18446744073709455488 kB
>               6 Committed_AS:    35136 kB
>               5 Committed_AS: 18446744073709454400 kB
>               7 Committed_AS:    35904 kB
>               3 Committed_AS: 18446744073709453248 kB
>               2 Committed_AS:    34752 kB
>               9 Committed_AS: 18446744073709453248 kB
>               8 Committed_AS:    34752 kB
>               3 Committed_AS: 18446744073709320960 kB
>               7 Committed_AS: 18446744073709454080 kB
>               3 Committed_AS: 18446744073709320960 kB
>               5 Committed_AS: 18446744073709454080 kB
>               6 Committed_AS: 18446744073709320960 kB

Because NR_CPUS can be greater than 1000 and meminfo_proc_show() does
not check for underflow.

But NR_CPUS proportional isn't good calculation.  In general,
possibility of lock contention is proportional to the number of online
cpus, not theorical maximum cpus (NR_CPUS).

The current kernel has generic percpu-counter stuff.  using it is right
way.  it makes code simplify and percpu_counter_read_positive() don't
make underflow issue.
Reported-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Eric B Munson <ebmunson@us.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: <stable@kernel.org>		[All kernel versions]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some drivers using of_register_platform_driver() wrapper break on sparc
because the wrapper isn't in the header file.  This patch moves it from
Microblaze and PowerPC implementations and makes it common code.

Fixes this sparc64 allmodconfig build error (at least):

drivers/leds/leds-gpio.c: In function `gpio_led_init':
drivers/leds/leds-gpio.c:295: error: implicit declaration of function `of_register_platform_driver'
drivers/leds/leds-gpio.c: In function `gpio_led_exit':
drivers/leds/leds-gpio.c:311: error: implicit declaration of function `of_unregister_platform_driver'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fixes the problem introduced by commit 3bfacef4 (get rid of
special-casing the /sbin/loader on alpha): osf/1 ecoff binary segfaults
when binfmt_aout built as module.  That happens because aout binary
handler gets on the top of the binfmt list due to late registration, and
kernel attempts to execute the binary without preparatory work that must
be done by binfmt_loader.

Fixed by changing the registration order of the default binfmt handlers
using list_add_tail() and introducing insert_binfmt() function which
places new handler on the top of the binfmt list.  This might be generally
useful for installing arch-specific frontends for default handlers or just
for overriding them.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Richard Henderson <rth@twiddle.net
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Richard Henderson <rth@twiddle.net
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Exception fixups for sections other than .text (like one in futex_init())
break the natural ordering of fixup entries, so sorting is required.

Without that the result of the exception table search depends on phase of
the moon.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Richard Henderson <rth@twiddle.net
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

These platforms got broken after u64 => 'long long' conversion.

Apparently that change was compile-tested with 'make allmodconfig', but it
doesn't include systems that depend on !ALPHA_LEGACY_START_ADDRESS.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Richard Henderson <rth@twiddle.net
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Uwe Geuder noted that he gets random bitmaps on a text console if he tried
to type extended characters (like the e acute).  For him everything above
unicode 0xa0 was corrupted.

After some digging there seems to be a little culprit in vgacon since the
beginning of ages (well git).  The function vgacon_font_get will store the
number of characters correctly in font->charcount but then calls to
vgacon_do_font_op(..., 0, 0).  Which means only the lower 256 characters
are actually stored to the fontdata.  The rest is left untouched.  So the
next time that saved data is used, the garbled font appears.  This happens
on every switch between text consoles.

Addresses https://bugs.launchpad.net/ubuntu/+source/linux/+bug/355057Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Tested-by: Uwe Geuder <ubuntuLp-ugeuder@sneakemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Current mem_cgroup_shrink_usage() has two problems.

1. It doesn't call mem_cgroup_out_of_memory and doesn't update
   last_oom_jiffies, so pagefault_out_of_memory invokes global OOM.

2. Considering hierarchy, shrinking has to be done from the
   mem_over_limit, not from the memcg which the page would be charged to.

mem_cgroup_try_charge_swapin() does all of these things properly, so we
use it and call cancel_charge_swapin when it succeeded.

The name of "shrink_usage" is not appropriate for this behavior, so we
change it too.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.cn>
Cc: Paul Menage <menage@google.com>
Cc: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The intention of commit aae8679b
("pagemap: fix bug in add_to_pagemap, require aligned-length reads of
/proc/pid/pagemap") was to force reads of /proc/pid/pagemap to be a
multiple of 8 bytes, but now it allows to read 0 bytes, which actually
puts some data to user's buffer.  According to POSIX, if count is zero,
read() should return zero and has no other results.
Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Cc: Thomas Tuttle <ttuttle@google.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Change page_mkwrite to allow implementations to return with the page
locked, and also change it's callers (in page fault paths) to hold the
lock until the page is marked dirty.  This allows the filesystem to have
full control of page dirtying events coming from the VM.

Rather than simply hold the page locked over the page_mkwrite call, we
call page_mkwrite with the page unlocked and allow callers to return with
it locked, so filesystems can avoid LOR conditions with page lock.

The problem with the current scheme is this: a filesystem that wants to
associate some metadata with a page as long as the page is dirty, will
perform this manipulation in its ->page_mkwrite.  It currently then must
return with the page unlocked and may not hold any other locks (according
to existing page_mkwrite convention).

In this window, the VM could write out the page, clearing page-dirty.  The
filesystem has no good way to detect that a dirty pte is about to be
attached, so it will happily write out the page, at which point, the
filesystem may manipulate the metadata to reflect that the page is no
longer dirty.

It is not always possible to perform the required metadata manipulation in
->set_page_dirty, because that function cannot block or fail.  The
filesystem may need to allocate some data structure, for example.

And the VM cannot mark the pte dirty before page_mkwrite, because
page_mkwrite is allowed to fail, so we must not allow any window where the
page could be written to if page_mkwrite does fail.

This solution of holding the page locked over the 3 critical operations
(page_mkwrite, setting the pte dirty, and finally setting the page dirty)
closes out races nicely, preventing page cleaning for writeout being
initiated in that window.  This provides the filesystem with a strong
synchronisation against the VM here.

- Sage needs this race closed for ceph filesystem.
- Trond for NFS (http://bugzilla.kernel.org/show_bug.cgi?id=12913).
- I need it for fsblock.
- I suspect other filesystems may need it too (eg. btrfs).
- I have converted buffer.c to the new locking. Even simple block allocation
  under dirty pages might be susceptible to i_size changing under partial page
  at the end of file (we also have a buffer.c-side problem here, but it cannot
  be fixed properly without this patch).
- Other filesystems (eg. NFS, maybe btrfs) will need to change their
  page_mkwrite functions themselves.

[ This also moves page_mkwrite another step closer to fault, which should
  eventually allow page_mkwrite to be moved into ->fault, and thus avoiding a
  filesystem calldown and page lock/unlock cycle in __do_fault. ]

[akpm@linux-foundation.org: fix derefs of NULL ->mapping]
Cc: Sage Weil <sage@newdream.net>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On a linux-next allyesconfig build:

kernel/trace/ring_buffer.c:1726:
	warning: passing argument 1 of 'atomic_cmpxchg' from incompatible pointer type
linux-next/arch/s390/include/asm/atomic.h:112:
	note: expected 'struct atomic_t *' but argument is of type 'struct atomic64_t *'

atomic_long_cmpxchg and atomic_long_xchg are incorrectly defined for 64
bit architectures.  They should be mapped to the atomic64_* variants.
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/serial/crisv10.c:4428: error: unknown field 'read_proc' specified in initializer

Commit 0f043a81 ("proc tty: remove struct
tty_operations::read_proc") removes the read_proc entry from struct
tty_operations.

Rework the proc handling in the CRISv10 serial driver to use proc_fops
instead.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add Roland and Oleg as formal ptrace maintainers, they've been doing the
job for a while.

Includes the file patterns requested by Joe.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is a bugfix for commit 3c776e64
("memcg: charge swapcache to proper memcg").

Used bit of swapcache is solid under page lock, but considering
move_account, pc->mem_cgroup is not.

We need lock_page_cgroup() anyway.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I will finish school soon, so replace my student address with this one.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix an obvious incorrect return status in autofs4_mount_busy().
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

By the time the memory cgroup code is notified about a swapin we
already hold a reference on the fault page.

If the cgroup callback fails make sure to unlock AND release the page
reference which was taken by lookup_swap_cach(), or we leak the reference.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

acpi_rs_get_pci_routing_table_length is not performing sufficient
validation on the package returned from _PRT.  It assumes a package of
packages and fails/faults if this is not the case.

We should validate each subpackage when extracted from the parent
package, and not accept objects of the wrong type, since that will just
cause the scanning to fail (likely with a kernel oops).

This can only happen with a serious BIOS bug, and is accompanied by a
warning something like this:

  ACPI Warning (nspredef-0949): \_SB_.PCI0.PEG4._PRT: Return Package type mismatch at index 0 - found Integer, expected Package [20090320]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
  eCryptfs: Fix min function comparison warning
  ecryptfs: fix printk format warning

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB (11652): au0828: fix kernel oops regression on USB disconnect.
  V4L/DVB (11626): cx23885: Two fixes for DViCO FusionHDTV DVB-T Dual Express
  V4L/DVB (11612): mx3_camera: Fix compilation with CONFIG_PM
  V4L/DVB (11570): patch: s2255drv: fix race condition on set mode
  V4L/DVB (11568): cx18: Fix the handling of i2c bus registration error
  V4L/DVB (11561a): move media after i2c
  V4L/DVB (11516): drivers/media/video/saa5246a.c: fix use-after-free
  V4L/DVB (11515): drivers/media/video/saa5249.c: fix use-after-free and leak
  V4L/DVB (11494a): cx231xx Kconfig fixes
  V4L/DVB (11494): cx18: Send correct input routing value to external audio multiplexers

A regression was introduced in hg changeset 33810c734a0d, which resulted in
a kernel panic whenever the device was disconnected from USB.  The call to
4l2_device_register() was overwriting the pointer for usb_set_intfdata(), so
when au0828_usb_disconnect() was called, the usb_get_intfdata() returned a
pointer to the v4l2_device instead of the au0828_dev structure.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Two fixes for DViCO FusionHDTV DVB-T Dual Express:

 * Reset correct tuner when reinitializing xc3028.
 * Disable the I2C gate control to avoid locking up the I2C bus.
Tested-by: John Knops <jknops@australiaonline.net.au>
Reviewed-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Christopher Pascoe <linuxdvb@itee.uq.edu.au>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

set_modeready flag must be set before command sent to USB in
s2255_write_config.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

* Return actual error values as returned by the i2c subsystem, rather
  than 0 or 1.
* If the registration of the second bus fails, unregister the first one
  before exiting, otherwise we are leaking resources.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Currently drivers/media drivers are linked very early - directly after
base, block, misc, and mfd and before ata, scsi, ide, input, firewire,
usb, and i2c. This breaks static build of video4linux drivers, that use
generic CPU i2c adapter drivers and the v4l2-subdev subsystem, because
during video4linux probing the v4l2-subdev core requires a struct
i2c_adapter context, which cannot be satisfied before the i2c subsystem is
initialised. Moving drivers/media after drivers/i2c fixes this problem.

The best way to trigger action is by submitting a patch:-) So, let's see
what comes out of it - on the one hand I don't see any reason why media
has to be linked this early, and nobody was able to give me one yesterday
as this problem has been discussed on linux-media, OTOH, maybe indeed it
would be better to move i2c the whole way up above media, but that'd be
much bigger of a change, I think.
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

I lowered the kfree(t) down a couple lines and removed the superflous
"t->vdev = NULL;"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

I moved the kfree() down a couple lines.  t->vdev is going to be in freed
memory so there is no point setting it to NULL.  I added a kfree(t) on a
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

selecting ALSA module breaks if !SND. Just remove select.

While here, let's fix the whitespacing at the Kconfig.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

A late v4l2_subdev framework change accidentally sent the audio input
routing value to the external multiplexer, instead of the muxer input routing
value to the external multiplexer.  This change corrects that error.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
  e100: do not go D3 in shutdown unless system is powering off
  netfilter: revised locking for x_tables
  Bluetooth: Fix connection establishment with low security requirement
  Bluetooth: Add different pairing timeout for Legacy Pairing
  Bluetooth: Ensure that HCI sysfs add/del is preempt safe
  net: Avoid extra wakeups of threads blocked in wait_for_packet()
  net: Fix typo in net_device_ops description.
  ipv4: Limit size of route cache hash table
  Add reference to CAPI 2.0 standard
  Documentation/isdn/INTERFACE.CAPI
  update Documentation/isdn/00-INDEX
  ixgbe: Fix WoL functionality for 82599 KX4 devices
  veth: prevent oops caused by netdev destructor
  xfrm: wrong hash value for temporary SA
  forcedeth: tx timeout fix
  net: Fix LL_MAX_HEADER for CONFIG_TR_MODULE
  mlx4_en: Handle page allocation failure during receive
  mlx4_en: Fix cleanup flow on cq activation
  vlan: update vlan carrier state for admin up/down
  netfilter: xt_recent: fix stack overread in compat code
  ...

After experimenting with kexec with the last merges after 2.6.29, I've
had some problems when probing e100.  It would not read the eeprom.  After
some bisects, I realized this has been like that since forever (at least
2.6.18).  The problem is that shutdown is doing the same thing that
suspend does and puts the device in D3 state.  I couldn't find a way to
get the device back to a sane state in the probe function.  So, based on
some similar patches from Rafael J. Wysocki for e1000, e1000e, and ixgbe,
I wrote this one for e100.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The x_tables are organized with a table structure and a per-cpu copies
of the counters and rules. On older kernels there was a reader/writer 
lock per table which was a performance bottleneck. In 2.6.30-rc, this
was converted to use RCU and the counters/rules which solved the performance
problems for do_table but made replacing rules much slower because of
the necessary RCU grace period.

This version uses a per-cpu set of spinlocks and counters to allow to
table processing to proceed without the cache thrashing of a global
reader lock and keeps the same performance for table updates.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>