SPI NOR comes with die erase support for multi die flashes, with new
octal protocols (1-1-8 and 1-8-8) parsed from SFDP and with an updated
documentation about what the contributors shall consider when proposing
flash additions or updates. Michael Walle stepped out from the reviewer
role to maintainer.

The current logic is probably fine but is a bit convoluted. Plus, we
don't want partial pages to be part of the sequential operation just in
case the core would optimize the page read with a subpage read (which
would break the sequence). This may happen on the first and last page
only, so if the start offset or the end offset is not aligned with a
page boundary, better avoid them to prevent any risk.

Cc: stable@vger.kernel.org
Fixes: 003fe4b9 ("mtd: rawnand: Support for sequential cache reads")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/linux-mtd/20231215123208.516590-5-miquel.raynal@bootlin.com

Some devices support sequential reads when using the on-die ECC engines,
some others do not. It is a bit hard to know which ones will break other
than experimentally, so in order to avoid such a difficult and painful
task, let's just pretend all devices should avoid using this
optimization when configured like this.

Cc: stable@vger.kernel.org
Fixes: 003fe4b9 ("mtd: rawnand: Support for sequential cache reads")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/linux-mtd/20231215123208.516590-4-miquel.raynal@bootlin.com

A couple of reports pointed at some strange failures happening a bit
randomly since the introduction of sequential page reads support. After
investigation it turned out the most likely reason for these issues was
the fact that sometimes a (longer) read might happen, starting at the
same page that was read previously. This is optimized by the raw NAND
core, by not sending the READ_PAGE command to the NAND device and just
reading out the data in a local cache. When this page is also flagged as
being the starting point for a sequential read, it means the page right
next will be accessed without the right instructions. The NAND chip will
be confused and will not output correct data. In order to avoid such
situation from happening anymore, we can however handle this case with a
bit of additional logic, to postpone the initialization of the read
sequence by one page.
Reported-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Closes: https://lore.kernel.org/linux-mtd/CAP1tNvS=NVAm-vfvYWbc3k9Cx9YxMc2uZZkmXk8h1NhGX877Zg@mail.gmail.com/Reported-by: Måns Rullgård <mans@mansr.com>
Closes: https://lore.kernel.org/linux-mtd/yw1xfs6j4k6q.fsf@mansr.com/Reported-by: Martin Hundebøll <martin@geanix.com>
Closes: https://lore.kernel.org/linux-mtd/9d0c42fcde79bfedfe5b05d6a4e9fdef71d3dd52.camel@geanix.com/
Fixes: 003fe4b9 ("mtd: rawnand: Support for sequential cache reads")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/linux-mtd/20231215123208.516590-3-miquel.raynal@bootlin.com

The ONFI specification states that devices do not need to support
sequential reads across LUN boundaries. In order to prevent such event
from happening and possibly failing, let's introduce the concept of
"pause" in the sequential read to handle these cases. The first/last
pages remain the same but any time we cross a LUN boundary we will end
and restart (if relevant) the sequential read operation.

Cc: stable@vger.kernel.org
Fixes: 003fe4b9 ("mtd: rawnand: Support for sequential cache reads")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/linux-mtd/20231215123208.516590-2-miquel.raynal@bootlin.com

If both ftl.ko and gluebi.ko are loaded, the notifier of ftl
triggers NULL pointer dereference when trying to access
‘gluebi->desc’ in gluebi_read().

ubi_gluebi_init
  ubi_register_volume_notifier
    ubi_enumerate_volumes
      ubi_notify_all
        gluebi_notify    nb->notifier_call()
          gluebi_create
            mtd_device_register
              mtd_device_parse_register
                add_mtd_device
                  blktrans_notify_add   not->add()
                    ftl_add_mtd         tr->add_mtd()
                      scan_header
                        mtd_read
                          mtd_read_oob
                            mtd_read_oob_std
                              gluebi_read   mtd->read()
                                gluebi->desc - NULL

Detailed reproduction information available at the Link [1],

In the normal case, obtain gluebi->desc in the gluebi_get_device(),
and access gluebi->desc in the gluebi_read(). However,
gluebi_get_device() is not executed in advance in the
ftl_add_mtd() process, which leads to NULL pointer dereference.

The solution for the gluebi module is to run jffs2 on the UBI
volume without considering working with ftl or mtdblock [2].
Therefore, this problem can be avoided by preventing gluebi from
creating the mtdblock device after creating mtd partition of the
type MTD_UBIVOLUME.

Fixes: 2ba3d76a ("UBI: make gluebi a separate module")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217992 [1]
Link: https://lore.kernel.org/lkml/441107100.23734.1697904580252.JavaMail.zimbra@nod.at/ [2]
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231220024619.2138625-1-wangzhaolong1@huawei.com

The initial description contained a typo.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231218130656.9020-1-wahrenst@gmx.net

As I'm doing more and more work professionally, move away from my
private mail address.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20231219091218.2846297-1-michael@walle.ccSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

BFPT 17th DWORD contains the information about 1-1-8 and 1-8-8.
Parse BFPT DWORD[17] instruction to determine whether flash
supports 1-1-8 and 1-8-8, and set its dummy cycles accordingly.

Validated only the 1-1-8 read using a macronix flash with
Xilinx board zynq-picozed.
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20231219102103.92738-2-jaimeliao.tw@gmail.com
[ta: update commit message, get rid of extra dereference]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

The mtd data shall be obtained with the mtd ioctls or with
new debugfs entries if one cares. Drop the debug prints.
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20231215082138.16063-5-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

The flash name is not reliable as we saw flash ID collisions.
Hide the flash name if not set.
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Reviewed-by: Michael Walle <michael@walle.cc>
[ta: update commit subject and description and the sysfs description]
Link: https://lore.kernel.org/r/20231215082138.16063-4-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

The flash name is unreliable as we saw flash ID collisions. Mark the
name as obsolete.
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20231215082138.16063-3-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

We saw flash ID collisions which make the flash name unreliable. Print
the manufacturer and device ID instead of the flash name.

Lower the print to dev_dbg to stop polluting the kernel log.
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20231215082138.16063-2-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

While switching to ref counters for track mtd devices use, the vmu-flash
driver was forgotten. The reason for reading the ref counter seems
debatable, but let's just fix the build for now.

Fixes: 19bfa9eb ("mtd: use refcount to prevent corruption")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312022315.79twVRZw-lkp@intel.com/
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231205075936.13831-1-miquel.raynal@bootlin.com

Since its introduction the driver was declaring a "usecount" variable,
but nobody ever used it upstream.

This was spot while grepping for usecount through mtd/ for other
reasons.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231205075431.13401-1-miquel.raynal@bootlin.com

Add support for the MT25QU01G 128MB Micron Serial NOR Flash Memory
model.

Link: https://www.micron.com/-/media/client/global/documents/products/data-sheet/nor-flash/serial-nor/mt25q/die-rev-b/mt25q_qlkt_u_01g_bbb_0.pdfSigned-off-by: Fabio Estevam <festevam@denx.de>
[ta: introduce die erase]
Link: https://lore.kernel.org/r/20231125123529.55686-6-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

There's no flash using it and we'd like to rely instead on SFDP data,
thus remove it.
Tested-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20231125123529.55686-5-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

Enable die erase for multi die flashes, it will speed the erase time.

Unfortunately, Micron does not provide a 4-byte opcode equivalent for
the die erase. The SFDP 4BAIT table fails to consider the die erase too,
the standard can be improved. Thus we're forced to enter in the 4 byte
address mode in order to benefit of the die erase.

Tested on n25q00. This flash defines the 4BAIT SFDP table, thus it will
use the 4BAIT opcodes for reads, page programs or erases, with the
exception that it will use the die erase command in the 4 byte address
mode.

Link: https://media-www.micron.com/-/media/client/global/documents/products/data-sheet/nor-flash/serial-nor/n25q/n25q_1gb_3v_65nm.pdf?rev=b6eba74759984f749f8c039bc5bc47b7
Link: https://media-www.micron.com/-/media/client/global/documents/products/data-sheet/nor-flash/serial-nor/mt25q/die-rev-b/mt25q_qlkt_l_02g_cbb_0.pdf?rev=43f7f66fc8da4d7d901b35fa51284c8f
Link: https://lore.kernel.org/r/20231125123529.55686-4-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

Enable die erase for spansion multi die flashes.
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20231125123529.55686-3-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

JESD216 mentions die erase, but does not provide an opcode for it.
Check BFPT dword 11, bits 30:24, "Chip Erase, Typical time", it says:

"Typical time to erase one chip (die). User must poll device busy to
determine if the operation has completed. For a device consisting of
multiple dies, that are individually accessed, the time is for each die
to which a chip erase command is applied."

So when a flash consists of a single die, this is the erase time for the
full chip (die) erase, and when it consists of multiple dies, it's the
die erase time. Chip and die are the same thing.

Add support for die erase. For now, benefit of the die erase when addr
and len are aligned with die size. This could be improved however for
the uniform and non-uniform erases cases to use the die erase when
possible. For example if one requests that an erase of a 2 die device
starting from the last 64KB of the first die to the end of the flash
size, we could use just 2 commands, a 64KB erase and a die erase.
This improvement is left as an exercise for the reader.
Tested-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20231125123529.55686-2-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

The architecture description is obsolete, it no longer applies to
the current SPI NOR framework state, remove it.
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20231124184902.1194235-3-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

Add sections about how to propose a new flash addition and about the
minimum testing requirements.
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20231124184902.1194235-2-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

After being a reviewer for a while, add myself as a maintainer for the
spi-nor subsystem.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Richard Weinberger <richard@nod.at>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231121122134.1952738-1-michael@walle.ccSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

The kernel offers and prefers the kernel sized types instead of the c99
types when not in the uapi directory, use them.

Link: https://lore.kernel.org/r/20231101145853.524045-2-tudor.ambarus@linaro.orgSigned-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>

The commands should be sorted inside the group definition.
Fix the ordering so we won't get following warning:
WARN_ON(iwl_cmd_groups_verify_sorted(trans_cfg))

Link: https://lore.kernel.org/regressions/2fa930bb-54dd-4942-a88d-05a47c8e9731@gmail.com/
Link: https://lore.kernel.org/linux-wireless/CAHk-=wix6kqQ5vHZXjOPpZBfM7mMm9bBZxi2Jh7XnaKCqVf94w@mail.gmail.com/
Fixes: b6e3d1ba ("wifi: iwlwifi: mvm: implement new firmware API for statistics")
Tested-by: Niklāvs Koļesņikovs <pinkflames.linux@gmail.com>
Tested-by: Damian Tometzki <damian@riscv-rocks.de>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'parisc-for-6.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux

Pull parisc architecture fixes from Helge Deller:

 - Include the upper 5 address bits when inserting TLB entries on a
   64-bit kernel.

   On physical machines those are ignored, but in qemu it's nice to have
   them included and to be correct.

 - Stop the 64-bit kernel and show a warning if someone tries to boot on
   a machine with a 32-bit CPU

 - Fix a "no previous prototype" warning in parport-gsc

* tag 'parisc-for-6.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Prevent booting 64-bit kernels on PA1.x machines
  parport: gsc: mark init function static
  parisc/pgtable: Do not drop upper 5 address bits of physical address

Merge tag 'loongarch-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson

Pull LoongArch updates from Huacai Chen:

 - support PREEMPT_DYNAMIC with static keys

 - relax memory ordering for atomic operations

 - support BPF CPU v4 instructions for LoongArch

 - some build and runtime warning fixes

* tag 'loongarch-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
  selftests/bpf: Enable cpu v4 tests for LoongArch
  LoongArch: BPF: Support signed mod instructions
  LoongArch: BPF: Support signed div instructions
  LoongArch: BPF: Support 32-bit offset jmp instructions
  LoongArch: BPF: Support unconditional bswap instructions
  LoongArch: BPF: Support sign-extension mov instructions
  LoongArch: BPF: Support sign-extension load instructions
  LoongArch: Add more instruction opcodes and emit_* helpers
  LoongArch/smp: Call rcutree_report_cpu_starting() earlier
  LoongArch: Relax memory ordering for atomic operations
  LoongArch: Mark __percpu functions as always inline
  LoongArch: Disable module from accessing external data directly
  LoongArch: Support PREEMPT_DYNAMIC with static keys

Pull powerpc fixes from Michael Ellerman:

 - Finish a refactor of pgprot_framebuffer() which dependend
   on some changes that were merged via the drm tree

 - Fix some kernel-doc warnings to quieten the bots

Thanks to Nathan Lynch and Thomas Zimmermann.

* tag 'powerpc-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/rtas: Fix ppc_rtas_rmo_buf_show() kernel-doc
  powerpc/pseries/rtas-work-area: Fix rtas_work_area_reserve_arena() kernel-doc
  powerpc/fb: Call internal __phys_mem_access_prot() in fbdev code
  powerpc: Remove file parameter from phys_mem_access_prot()
  powerpc/machdep: Remove trailing whitespaces

Pull smb client fixes from Steve French:

 - ctime caching fix (for setxattr)

 - encryption fix

 - DNS resolver mount fix

 - debugging improvements

 - multichannel fixes including cases where server stops or starts
   supporting multichannel after mount

 - reconnect fix

 - minor cleanups

* tag '6.7-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number for cifs.ko
  cifs: handle when server stops supporting multichannel
  cifs: handle when server starts supporting multichannel
  Missing field not being returned in ioctl CIFS_IOC_GET_MNT_INFO
  smb3: allow dumping session and tcon id to improve stats analysis and debugging
  smb: client: fix mount when dns_resolver key is not available
  smb3: fix caching of ctime on setxattr
  smb3: minor cleanup of session handling code
  cifs: reconnect work should have reference on server struct
  cifs: do not pass cifs_sb when trying to add channels
  cifs: account for primary channel in the interface list
  cifs: distribute channels across interfaces based on speed
  cifs: handle cases where a channel is closed
  smb3: more minor cleanups for session handling routines
  smb3: minor RDMA cleanup
  cifs: Fix encryption of cleared, but unset rq_iter data buffers

Merge tag 'probes-fixes-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull probes fixes from Masami Hiramatsu:

 - Documentation update: Add a note about argument and return value
   fetching is the best effort because it depends on the type.

 - objpool: Fix to make internal global variables static in
   test_objpool.c.

 - kprobes: Unify kprobes_exceptions_nofify() prototypes. There are the
   same prototypes in asm/kprobes.h for some architectures, but some of
   them are missing the prototype and it causes a warning. So move the
   prototype into linux/kprobes.h.

 - tracing: Fix to check the tracepoint event and return event at
   parsing stage. The tracepoint event doesn't support %return but if
   $retval exists, it will be converted to %return silently. This finds
   that case and rejects it.

 - tracing: Fix the order of the descriptions about the parameters of
   __kprobe_event_gen_cmd_start() to be consistent with the argument
   list of the function.

* tag 'probes-fixes-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  tracing/kprobes: Fix the order of argument descriptions
  tracing: fprobe-event: Fix to check tracepoint event and return
  kprobes: unify kprobes_exceptions_nofify() prototypes
  lib: test_objpool: make global variables static
  Documentation: tracing: Add a note about argument and retval access

Pull fbdev fixes and cleanups from Helge Deller:

 - fix double free and resource leaks in imsttfb

 - lots of remove callback cleanups and section mismatch fixes in
   omapfb, amifb and atmel_lcdfb

 - error code fix and memparse simplification in omapfb

* tag 'fbdev-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev: (31 commits)
  fbdev: fsl-diu-fb: mark wr_reg_wa() static
  fbdev: amifb: Convert to platform remove callback returning void
  fbdev: amifb: Mark driver struct with __refdata to prevent section mismatch warning
  fbdev: hyperv_fb: fix uninitialized local variable use
  fbdev: omapfb/tpd12s015: Convert to platform remove callback returning void
  fbdev: omapfb/tfp410: Convert to platform remove callback returning void
  fbdev: omapfb/sharp-ls037v7dw01: Convert to platform remove callback returning void
  fbdev: omapfb/opa362: Convert to platform remove callback returning void
  fbdev: omapfb/hdmi: Convert to platform remove callback returning void
  fbdev: omapfb/dvi: Convert to platform remove callback returning void
  fbdev: omapfb/dsi-cm: Convert to platform remove callback returning void
  fbdev: omapfb/dpi: Convert to platform remove callback returning void
  fbdev: omapfb/analog-tv: Convert to platform remove callback returning void
  fbdev: atmel_lcdfb: Convert to platform remove callback returning void
  fbdev: omapfb/tpd12s015: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/tfp410: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/sharp-ls037v7dw01: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/opa362: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/hdmi: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/dvi: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  ...

The order of descriptions should be consistent with the argument list of
the function, so "kretprobe" should be the second one.

int __kprobe_event_gen_cmd_start(struct dynevent_cmd *cmd, bool kretprobe,
                                 const char *name, const char *loc, ...)

Link: https://lore.kernel.org/all/20231031041305.3363712-1-yujie.liu@intel.com/

Fixes: 2a588dd1 ("tracing: Add kprobe event command generation functions")
Suggested-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Yujie Liu <yujie.liu@intel.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>

Pull drm fixes from Daniel Vetter:
 "Dave's VPN to the big machine died, so it's on me to do fixes pr this
  and next week while everyone else is at plumbers.

   - big pile of amd fixes, but mostly for hw support newly added in 6.7

   - i915 fixes, mostly minor things

   - qxl memory leak fix

   - vc4 uaf fix in mock helpers

   - syncobj fix for DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE"

* tag 'drm-next-2023-11-10' of git://anongit.freedesktop.org/drm/drm: (78 commits)
  drm/amdgpu: fix error handling in amdgpu_vm_init
  drm/amdgpu: Fix possible null pointer dereference
  drm/amdgpu: move UVD and VCE sched entity init after sched init
  drm/amdgpu: move kfd_resume before the ip late init
  drm/amd: Explicitly check for GFXOFF to be enabled for s0ix
  drm/amdgpu: Change WREG32_RLC to WREG32_SOC15_RLC where inst != 0 (v2)
  drm/amdgpu: Use correct KIQ MEC engine for gfx9.4.3 (v5)
  drm/amdgpu: add smu v13.0.6 pcs xgmi ras error query support
  drm/amdgpu: fix software pci_unplug on some chips
  drm/amd/display: remove duplicated argument
  drm/amdgpu: correct mca debugfs dump reg list
  drm/amdgpu: correct acclerator check architecutre dump
  drm/amdgpu: add pcs xgmi v6.4.0 ras support
  drm/amdgpu: Change extended-scope MTYPE on GC 9.4.3
  drm/amdgpu: disable smu v13.0.6 mca debug mode by default
  drm/amdgpu: Support multiple error query modes
  drm/amdgpu: refine smu v13.0.6 mca dump driver
  drm/amdgpu: Do not program PF-only regs in hdp_v4_0.c under SRIOV (v2)
  drm/amdgpu: Skip PCTL0_MMHUB_DEEPSLEEP_IB write in jpegv4.0.3 under SRIOV
  drm: amd: Resolve Sphinx unexpected indentation warning
  ...

Pull arm64 fixes from Catalin Marinas:
 "Mostly PMU fixes and a reworking of the pseudo-NMI disabling on broken
  MediaTek firmware:

   - Move the MediaTek GIC quirk handling from irqchip to core. Before
     the merging window commit 44bd78dd ("irqchip/gic-v3: Disable
     pseudo NMIs on MediaTek devices w/ firmware issues") temporarily
     addressed this issue. Fixed now at a deeper level in the arch code

   - Reject events meant for other PMUs in the CoreSight PMU driver,
     otherwise some of the core PMU events would disappear

   - Fix the Armv8 PMUv3 driver driver to not truncate 64-bit registers,
     causing some events to be invisible

   - Remove duplicate declaration of __arm64_sys##name following the
     patch to avoid prototype warning for syscalls

   - Typos in the elf_hwcap documentation"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64/syscall: Remove duplicate declaration
  Revert "arm64: smp: avoid NMI IPIs with broken MediaTek FW"
  arm64: Move MediaTek GIC quirk handling from irqchip to core
  arm64/arm: arm_pmuv3: perf: Don't truncate 64-bit registers
  perf: arm_cspmu: Reject events meant for other PMUs
  Documentation/arm64: Fix typos in elf_hwcaps

Pull sound fixes from Takashi Iwai:
 "A collection of fixes for rc1.

  The majority of changes are various ASoC driver-specific small fixes
  and usual HD-audio quirks, while there are a couple of core changes: a
  fix in ALSA core procfs code to avoid deadlocks at disconnection and
  an ASoC core fix for DAPM clock widgets"

* tag 'sound-fix-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  OSS: dmasound/paula: Convert to platform remove callback returning void
  ALSA: hda: ASUS UM5302LA: Added quirks for cs35L41/10431A83 on i2c bus
  ALSA: info: Fix potential deadlock at disconnection
  ASoC: nau8540: Add self recovery to improve capture quility
  ALSA: hda/realtek: Add support dual speaker for Dell
  ALSA: hda: Add ASRock X670E Taichi to denylist
  ALSA: hda/realtek: Add quirk for ASUS UX7602ZM
  ASoC: SOF: sof-client: trivial: fix comment typo
  ASoC: dapm: fix clock get name
  ASoC: hdmi-codec: register hpd callback on component probe
  ASoC: mediatek: mt8186_mt6366_rt1019_rt5682s: trivial: fix error messages
  ASoC: da7219: Improve system suspend and resume handling
  ASoC: codecs: Modify macro value error
  ASoC: codecs: Modify the wrong judgment of re value
  ASoC: codecs: Modify the maximum value of calib
  ASoC: amd: acp: fix for i2s mode register field update
  ASoC: codecs: aw88399: Fix -Wuninitialized in aw_dev_set_vcalb()
  ASoC: rt712-sdca: fix speaker route missing issue
  ASoC: rockchip: Fix unused rockchip_i2s_tdm_match warning for !CONFIG_OF
  ASoC: ti: omap-mcbsp: Fix runtime PM underflow warnings

amd-drm-next-6.7-2023-11-10:

amdgpu:
- SR-IOV fixes
- DMCUB fixes
- DCN3.5 fixes
- DP2 fixes
- SubVP fixes
- SMU14 fixes
- SDMA4.x fixes
- Suspend/resume fixes
- AGP regression fix
- UAF fixes for some error cases
- SMU 13.0.6 fixes
- Documentation fixes
- RAS fixes
- Hotplug fixes
- Scheduling entity ordering fix
- GPUVM fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110190703.4741-1-alexander.deucher@amd.com

Pull spi fixes from Mark Brown:
 "A couple of fixes that came in during the merge window: one Kconfig
  dependency fix and another fix for a long standing issue where a sync
  transfer races with system suspend"

* tag 'spi-fix-v6.7-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: Fix null dereference on suspend
  spi: spi-zynq-qspi: add spi-mem to driver kconfig dependencies

Pull MMC fixes from Ulf Hansson:
 "MMC core:
   - Fix broken cache-flush support for Micron eMMCs
   - Revert 'mmc: core: Capture correct oemid-bits for eMMC cards'

  MMC host:
   - sdhci_am654: Fix TAP value parsing for legacy speed mode
   - sdhci-pci-gli: Fix support for ASPM mode for GL9755/GL9750
   - vub300: Fix an error path in probe"

* tag 'mmc-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-pci-gli: GL9750: Mask the replay timer timeout of AER
  mmc: sdhci-pci-gli: GL9755: Mask the replay timer timeout of AER
  Revert "mmc: core: Capture correct oemid-bits for eMMC cards"
  mmc: vub300: fix an error code
  mmc: Add quirk MMC_QUIRK_BROKEN_CACHE_FLUSH for Micron eMMC Q2J54A
  mmc: sdhci_am654: fix start loop index for TAP value parsing

Merge tag 'pwm/for-6.7-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fixes from Thierry Reding:
 "This contains two very small fixes that I failed to include in the
  main pull request"

* tag 'pwm/for-6.7-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: Fix double shift bug
  pwm: samsung: Fix a bit test in pwm_samsung_resume()