- 17 Nov, 2015 27 commits
-
-
Christoph Hellwig authored
commit 15e3d5a2 upstream. 3w controller don't dma map small single SGL entry commands but instead bounce buffer them. Add a helper to identify these commands and don't call scsi_dma_unmap for them. Based on an earlier patch from James Bottomley. Fixes: 118c85 ("3w-9xxx: fix command completion race") Reported-by:
Tóth Attila <atoth@atoth.sote.hu> Tested-by:
Christoph Hellwig <hch@lst.de> Acked-by:
Adam Radford <aradford@gmail.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Peter Zijlstra authored
commit 95913d97 upstream. So the problem this patch is trying to address is as follows: CPU0 CPU1 context_switch(A, B) ttwu(A) LOCK A->pi_lock A->on_cpu == 0 finish_task_switch(A) prev_state = A->state <-. WMB | A->on_cpu = 0; | UNLOCK rq0->lock | | context_switch(C, A) `-- A->state = TASK_DEAD prev_state == TASK_DEAD put_task_struct(A) context_switch(A, C) finish_task_switch(A) A->state == TASK_DEAD put_task_struct(A) The argument being that the WMB will allow the load of A->state on CPU0 to cross over and observe CPU1's store of A->state, which will then result in a double-drop and use-after-free. Now the comment states (and this was true once upon a long time ago) that we need to observe A->state while holding rq->lock because that will order us against the wakeup; however the wakeup will not in fact acquire (that) rq->lock; it takes A->pi_lock these days. We can obviously fix this by upgrading the WMB to an MB, but that is expensive, so we'd rather avoid that. The alternative this patch takes is: smp_store_release(&A->on_cpu, 0), which avoids the MB on some archs, but not important ones like ARM. Reported-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Cc: manfred@colorfullife.com Cc: will.deacon@arm.com Fixes: e4a52bcb ("sched: Remove rq->lock from the first half of ttwu()") Link: http://lkml.kernel.org/r/20150929124509.GG3816@twins.programming.kicks-ass.netSigned-off-by:
Ingo Molnar <mingo@kernel.org> [bwh: Backported to 3.2: - Adjust filename - As smp_store_release() is not defined, use smp_mb()] Signed-off-by:
-
Takashi Iwai authored
commit 225db576 upstream. When OSS emulation is loaded on ISA SB AWE32 chip, we get now kernel warnings like: WARNING: CPU: 0 PID: 2791 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x51/0x80() sysfs: cannot create duplicate filename '/devices/isa/sbawe.0/sound/card0/seq-oss-0-0' It's because both emux synth and opl3 drivers try to register their OSS device object with the same static index number 0. This hasn't been a big problem until the recent rewrite of device management code (that exposes sysfs at the same time), but it's been an obvious bug. This patch works around it just by using a different index number of emux synth object. There can be a more elegant way to fix, but it's enough for now, as this code won't be touched so often, in anyway. Reported-and-tested-by:
Michael Shell <list1@michaelshell.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Johannes Berg authored
commit 5bd16687 upstream. The code to send the RX PN data (for each TID) to the firmware has a devastating bug: it overwrites the data for TID 0 with all the TID data, leaving the remaining TIDs zeroed. This will allow replays to actually be accepted by the firmware, which could allow waking up the system. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Guillaume Nault authored
commit e6740165 upstream. Since commit 2b018d57 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release"), pppoe_release() calls dev_put(po->pppoe_dev) if sk is in the PPPOX_ZOMBIE state. But pppoe_flush_dev() can set sk->sk_state to PPPOX_ZOMBIE _and_ reset po->pppoe_dev to NULL. This leads to the following oops: [ 570.140800] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e0 [ 570.142931] IP: [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] PGD 3d119067 PUD 3dbc1067 PMD 0 [ 570.144601] Oops: 0000 [#1] SMP [ 570.144601] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppoe pppox ppp_generic slhc loop crc32c_intel ghash_clmulni_intel jitterentropy_rng sha256_generic hmac drbg ansi_cprng aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper acpi_cpufreq evdev serio_raw processor button ext4 crc16 mbcache jbd2 virtio_net virtio_blk virtio_pci virtio_ring virtio [ 570.144601] CPU: 1 PID: 15738 Comm: ppp-apitest Not tainted 4.2.0 #1 [ 570.144601] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014 [ 570.144601] task: ffff88003d30d600 ti: ffff880036b60000 task.ti: ffff880036b60000 [ 570.144601] RIP: 0010:[<ffffffffa018c701>] [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP: 0018:ffff880036b63e08 EFLAGS: 00010202 [ 570.144601] RAX: 0000000000000000 RBX: ffff880034340000 RCX: 0000000000000206 [ 570.144601] RDX: 0000000000000006 RSI: ffff88003d30dd20 RDI: ffff88003d30dd20 [ 570.144601] RBP: ffff880036b63e28 R08: 0000000000000001 R09: 0000000000000000 [ 570.144601] R10: 00007ffee9b50420 R11: ffff880034340078 R12: ffff8800387ec780 [ 570.144601] R13: ffff8800387ec7b0 R14: ffff88003e222aa0 R15: ffff8800387ec7b0 [ 570.144601] FS: 00007f5672f48700(0000) GS:ffff88003fc80000(0000) knlGS:0000000000000000 [ 570.144601] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 570.144601] CR2: 00000000000004e0 CR3: 0000000037f7e000 CR4: 00000000000406a0 [ 570.144601] Stack: [ 570.144601] ffffffffa018f240 ffff8800387ec780 ffffffffa018f240 ffff8800387ec7b0 [ 570.144601] ffff880036b63e48 ffffffff812caabe ffff880039e4e000 0000000000000008 [ 570.144601] ffff880036b63e58 ffffffff812cabad ffff880036b63ea8 ffffffff811347f5 [ 570.144601] Call Trace: [ 570.144601] [<ffffffff812caabe>] sock_release+0x1a/0x75 [ 570.144601] [<ffffffff812cabad>] sock_close+0xd/0x11 [ 570.144601] [<ffffffff811347f5>] __fput+0xff/0x1a5 [ 570.144601] [<ffffffff811348cb>] ____fput+0x9/0xb [ 570.144601] [<ffffffff81056682>] task_work_run+0x66/0x90 [ 570.144601] [<ffffffff8100189e>] prepare_exit_to_usermode+0x8c/0xa7 [ 570.144601] [<ffffffff81001a26>] syscall_return_slowpath+0x16d/0x19b [ 570.144601] [<ffffffff813babb1>] int_ret_from_sys_call+0x25/0x9f [ 570.144601] Code: 48 8b 83 c8 01 00 00 a8 01 74 12 48 89 df e8 8b 27 14 e1 b8 f7 ff ff ff e9 b7 00 00 00 8a 43 12 a8 0b 74 1c 48 8b 83 a8 04 00 00 <48> 8b 80 e0 04 00 00 65 ff 08 48 c7 83 a8 04 00 00 00 00 00 00 [ 570.144601] RIP [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP <ffff880036b63e08> [ 570.144601] CR2: 00000000000004e0 [ 570.200518] ---[ end trace 46956baf17349563 ]--- pppoe_flush_dev() has no reason to override sk->sk_state with PPPOX_ZOMBIE. pppox_unbind_sock() already sets sk->sk_state to PPPOX_DEAD, which is the correct state given that sk is unbound and po->pppoe_dev is NULL. Fixes: 2b018d57 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Tested-by:
Oleksii Berezhniak <core@irc.lg.ua> Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jann Horn authored
commit 0c556271 upstream. This is mostly a hardening fix, given that write-only access to other users' ttys is usually only given through setgid tty executables. Signed-off-by:
Jann Horn <jann@thejh.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: - __proc_set_tty() also takes a task_struct pointer] Signed-off-by:
-
Kosuke Tatsukawa authored
commit e81107d4 upstream. My colleague ran into a program stall on a x86_64 server, where n_tty_read() was waiting for data even if there was data in the buffer in the pty. kernel stack for the stuck process looks like below. #0 [ffff88303d107b58] __schedule at ffffffff815c4b20 #1 [ffff88303d107bd0] schedule at ffffffff815c513e #2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818 #3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2 #4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23 #5 [ffff88303d107dd0] tty_read at ffffffff81368013 #6 [ffff88303d107e20] __vfs_read at ffffffff811a3704 #7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57 #8 [ffff88303d107f00] sys_read at ffffffff811a4306 #9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7 There seems to be two problems causing this issue. First, in drivers/tty/n_tty.c, __receive_buf() stores the data and updates ldata->commit_head using smp_store_release() and then checks the wait queue using waitqueue_active(). However, since there is no memory barrier, __receive_buf() could return without calling wake_up_interactive_poll(), and at the same time, n_tty_read() could start to wait in wait_woken() as in the following chart. __receive_buf() n_tty_read() ------------------------------------------------------------------------ if (waitqueue_active(&tty->read_wait)) /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ add_wait_queue(&tty->read_wait, &wait); ... if (!input_available_p(tty, 0)) { smp_store_release(&ldata->commit_head, ldata->read_head); ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ The second problem is that n_tty_read() also lacks a memory barrier call and could also cause __receive_buf() to return without calling wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken() as in the chart below. __receive_buf() n_tty_read() ------------------------------------------------------------------------ spin_lock_irqsave(&q->lock, flags); /* from add_wait_queue() */ ... if (!input_available_p(tty, 0)) { /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ smp_store_release(&ldata->commit_head, ldata->read_head); if (waitqueue_active(&tty->read_wait)) __add_wait_queue(q, wait); spin_unlock_irqrestore(&q->lock,flags); /* from add_wait_queue() */ ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ There are also other places in drivers/tty/n_tty.c which have similar calls to waitqueue_active(), so instead of adding many memory barrier calls, this patch simply removes the call to waitqueue_active(), leaving just wake_up*() behind. This fixes both problems because, even though the memory access before or after the spinlocks in both wake_up*() and add_wait_queue() can sneak into the critical section, it cannot go past it and the critical section assures that they will be serialized (please see "INTER-CPU ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a better explanation). Moreover, the resulting code is much simpler. Latency measurement using a ping-pong test over a pty doesn't show any visible performance drop. Signed-off-by:
Kosuke Tatsukawa <tatsu@ab.jp.nec.com> Signed-off-by:
-
Vincent Palatin authored
commit 72194739 upstream. Add a device quirk for the Logitech PTZ Pro Camera and its sibling the ConferenceCam CC3000e Camera. This fixes the failed camera enumeration on some boot, particularly on machines with fast CPU. Tested by connecting a Logitech PTZ Pro Camera to a machine with a Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles while recording the kernel logs and taking camera picture after each boot. Before the patch, more than 7% of the boots show some enumeration transfer failures and in a few of them, the kernel is giving up before actually enumerating the webcam. After the patch, the enumeration has been correct on every reboot. Signed-off-by:
Vincent Palatin <vpalatin@chromium.org> Signed-off-by:
-
Yao-Wen Mao authored
commit 8484bf29 upstream. These two headphones need a reset-resume quirk to properly resume to original volume level. Signed-off-by:
Yao-Wen Mao <yaowen@google.com> Signed-off-by:
-
Dan Carpenter authored
commit eda7d0f3 upstream. "num_read" is in byte units but we are write u16s so we end up write twice as much as intended. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
John Stultz authored
commit 67dfae0c upstream. This patch fixes one cases where abs() was being used with 64-bit nanosecond values, where the result may be capped at 32-bits. This potentially could cause watchdog false negatives on 32-bit systems, so this patch addresses the issue by using abs64(). Signed-off-by:
John Stultz <john.stultz@linaro.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Link: http://lkml.kernel.org/r/1442279124-7309-2-git-send-email-john.stultz@linaro.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
NeilBrown authored
commit 66eefe5d upstream. Calling e.g. blk_queue_max_hw_sectors() after calls to disk_stack_limits() discards the settings determined by disk_stack_limits(). So we need to make those calls first. Fixes: 199dc6ed ("md/raid0: update queue parameter in a safer location.") Reported-by:
Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by:
NeilBrown <neilb@suse.com> [bwh: Backported to 3.2: the code being moved looks a little different] Signed-off-by:
-
NeilBrown authored
commit 199dc6ed upstream. When a (e.g.) RAID5 array is reshaped to RAID0, the updating of queue parameters (e.g. max number of sectors per bio) is done in the wrong place. It should be part of ->run, but it is actually part of ->takeover. This means it happens before level_store() calls: blk_set_stacking_limits(&mddev->queue->limits); and so it ineffective. This can lead to errors from underlying devices. So move all the relevant settings out of create_stripe_zones() and into raid0_run(). As this can lead to a bug-on it is suitable for any -stable kernel which supports reshape to RAID0. So 2.6.35 or later. As the bug has been present for five years there is no urgency, so no need to rush into -stable. Fixes: 9af204cf ("md: Add support for Raid5->Raid0 and Raid10->Raid0 takeover") Reported-by:
Yi Zhang <yizhan@redhat.com> Signed-off-by:
-
Steve French authored
commit 646200a0 upstream. The error paths in set_file_size for cifs and smb3 are incorrect. In the unlikely event that a server did not support set file info of the file size, the code incorrectly falls back to trying SMBWriteX (note that only the original core SMB Write, used for example by DOS, can set the file size this way - this actually does not work for the more recent SMBWriteX). The idea was since the old DOS SMB Write could set the file size if you write zero bytes at that offset then use that if server rejects the normal set file info call. Fortunately the SMBWriteX will never be sent on the wire (except when file size is zero) since the length and offset fields were reversed in the two places in this function that call SMBWriteX causing the fall back path to return an error. It is also important to never call an SMB request from an SMB2/sMB3 session (which theoretically would be possible, and can cause a brief session drop, although the client recovers) so this should be fixed. In practice this path does not happen with modern servers but the error fall back to SMBWriteX is clearly wrong. Removing the calls to SMBWriteX in the error paths in cifs_set_file_size Pointed out by PaX/grsecurity team Signed-off-by:
Steve French <steve.french@primarydata.com> Reported-by:
PaX Team <pageexec@freemail.hu> CC: Emese Revfy <re.emese@gmail.com> CC: Brad Spengler <spender@grsecurity.net> [bwh: Backported to 3.2: deleted code looks slightly different] Signed-off-by:
-
Mel Gorman authored
commit 2f84a899 upstream. SunDong reported the following on https://bugzilla.kernel.org/show_bug.cgi?id=103841 I think I find a linux bug, I have the test cases is constructed. I can stable recurring problems in fedora22(4.0.4) kernel version, arch for x86_64. I construct transparent huge page, when the parent and child process with MAP_SHARE, MAP_PRIVATE way to access the same huge page area, it has the opportunity to lead to huge page copy on write failure, and then it will munmap the child corresponding mmap area, but then the child mmap area with VM_MAYSHARE attributes, child process munmap this area can trigger VM_BUG_ON in set_vma_resv_flags functions (vma - > vm_flags & VM_MAYSHARE). There were a number of problems with the report (e.g. it's hugetlbfs that triggers this, not transparent huge pages) but it was fundamentally correct in that a VM_BUG_ON in set_vma_resv_flags() can be triggered that looks like this vma ffff8804651fd0d0 start 00007fc474e00000 end 00007fc475e00000 next ffff8804651fd018 prev ffff8804651fd188 mm ffff88046b1b1800 prot 8000000000000027 anon_vma (null) vm_ops ffffffff8182a7a0 pgoff 0 file ffff88106bdb9800 private_data (null) flags: 0x84400fb(read|write|shared|mayread|maywrite|mayexec|mayshare|dontexpand|hugetlb) ------------ kernel BUG at mm/hugetlb.c:462! SMP Modules linked in: xt_pkttype xt_LOG xt_limit [..] CPU: 38 PID: 26839 Comm: map Not tainted 4.0.4-default #1 Hardware name: Dell Inc. PowerEdge R810/0TT6JF, BIOS 2.7.4 04/26/2012 set_vma_resv_flags+0x2d/0x30 The VM_BUG_ON is correct because private and shared mappings have different reservation accounting but the warning clearly shows that the VMA is shared. When a private COW fails to allocate a new page then only the process that created the VMA gets the page -- all the children unmap the page. If the children access that data in the future then they get killed. The problem is that the same file is mapped shared and private. During the COW, the allocation fails, the VMAs are traversed to unmap the other private pages but a shared VMA is found and the bug is triggered. This patch identifies such VMAs and skips them. Signed-off-by:
Mel Gorman <mgorman@techsingularity.net> Reported-by:
SunDong <sund_sky@126.com> Reviewed-by:
Michal Hocko <mhocko@suse.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: David Rientjes <rientjes@google.com> Reviewed-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Ben Hutchings authored
commit 95c2b175 upstream. Per-IRQ directories in procfs are created only when a handler is first added to the irqdesc, not when the irqdesc is created. In the case of a shared IRQ, multiple tasks can race to create a directory. This race condition seems to have been present forever, but is easier to hit with async probing. Signed-off-by:
-
Thomas Gleixner authored
commit eddd3826 upstream. Dmitry Vyukov reported the following using trinity and the memory error detector AddressSanitizer (https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerForKernel). [ 124.575597] ERROR: AddressSanitizer: heap-buffer-overflow on address ffff88002e280000 [ 124.576801] ffff88002e280000 is located 131938492886538 bytes to the left of 28857600-byte region [ffffffff81282e0a, ffffffff82e0830a) [ 124.578633] Accessed by thread T10915: [ 124.579295] inlined in describe_heap_address ./arch/x86/mm/asan/report.c:164 [ 124.579295] #0 ffffffff810dd277 in asan_report_error ./arch/x86/mm/asan/report.c:278 [ 124.580137] #1 ffffffff810dc6a0 in asan_check_region ./arch/x86/mm/asan/asan.c:37 [ 124.581050] #2 ffffffff810dd423 in __tsan_read8 ??:0 [ 124.581893] #3 ffffffff8107c093 in get_wchan ./arch/x86/kernel/process_64.c:444 The address checks in the 64bit implementation of get_wchan() are wrong in several ways: - The lower bound of the stack is not the start of the stack page. It's the start of the stack page plus sizeof (struct thread_info) - The upper bound must be: top_of_stack - TOP_OF_KERNEL_STACK_PADDING - 2 * sizeof(unsigned long). The 2 * sizeof(unsigned long) is required because the stack pointer points at the frame pointer. The layout on the stack is: ... IP FP ... IP FP. So we need to make sure that both IP and FP are in the bounds. Fix the bound checks and get rid of the mix of numeric constants, u64 and unsigned long. Making all unsigned long allows us to use the same function for 32bit as well. Use READ_ONCE() when accessing the stack. This does not prevent a concurrent wakeup of the task and the stack changing, but at least it avoids TOCTOU. Also check task state at the end of the loop. Again that does not prevent concurrent changes, but it avoids walking for nothing. Add proper comments while at it. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Reported-by:
Sasha Levin <sasha.levin@oracle.com> Based-on-patch-from: Wolfram Gloger <wmglo@dent.med.uni-muenchen.de> Signed-off-by:
Borislav Petkov <bp@alien8.de> Reviewed-by:
-
James Hogan authored
commit 53960059 upstream. If there is a DMA zone (usually 24bit = 16MB I believe), but no DMA32 zone, as is the case for some 32-bit kernels, then massage_gfp_flags() will cause DMA memory allocated for devices with a 32..63-bit coherent_dma_mask to fall back to using __GFP_DMA, even though there may only be 32-bits of physical address available anyway. Correct that case to compare against a mask the size of phys_addr_t instead of always using a 64-bit mask. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Fixes: a2e715a8 ("MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.") Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/9610/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
shengyong authored
commit 7c7feb2e upstream. UBI: attaching mtd1 to ubi0 UBI: scanning is finished UBI error: init_volumes: not enough PEBs, required 706, available 686 UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1) UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM UBI error: ubi_init: cannot attach mtd1 If available PEBs are not enough when initializing volumes, return -ENOSPC directly. If available PEBs are not enough when initializing WL, return -ENOSPC instead of -ENOMEM. Signed-off-by:
Sheng Yong <shengyong1@huawei.com> Signed-off-by:
Richard Weinberger <richard@nod.at> Reviewed-by:
David Gstir <david@sigma-star.at> Signed-off-by:
-
Richard Weinberger authored
commit 281fda27 upstream. Make sure that data_size is less than LEB size. Otherwise a handcrafted UBI image is able to trigger an out of bounds memory access in ubi_compare_lebs(). Signed-off-by:
-
Malcolm Crossley authored
commit 64c98e7f upstream. Sanitizing the e820 map may produce extra E820 entries which would result in the topmost E820 entries being removed. The removed entries would typically include the top E820 usable RAM region and thus result in the domain having signicantly less RAM available to it. Fix by allowing sanitize_e820_map to use the full size of the allocated E820 array. Signed-off-by:
Malcolm Crossley <malcolm.crossley@citrix.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> [bwh: Backported to 3.2: s/xen_e820_map_entries/memmap.nr_entries/; s/xen_e820_map/map/g] Signed-off-by:
-
Andreas Schwab authored
commit 8474ba74 upstream. Make sure the compiler does not modify arguments of syscall functions. This can happen if the compiler generates a tailcall to another function. For example, without asmlinkage_protect sys_openat is compiled into this function: sys_openat: clr.l %d0 move.w 18(%sp),%d0 move.l %d0,16(%sp) jbra do_sys_open Note how the fourth argument is modified in place, modifying the register %d4 that gets restored from this stack slot when the function returns to user-space. The caller may expect the register to be unmodified across system calls. Signed-off-by:
Andreas Schwab <schwab@linux-m68k.org> Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Felix Fietkau authored
commit 029cd037 upstream. ath9k inserts padding between the 802.11 header and the data area (to align it). Since it didn't declare this extra required headroom, this led to some nasty issues like randomly dropped packets in some setups. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Mark Brown authored
commit 176fc2d5 upstream. The in kernel snprintf() will conveniently return the actual length of the printed string even if not given an output beffer at all so just do that rather than relying on the user to pass in a suitable buffer, ensuring that we don't need to worry if the buffer was truncated due to the size of the buffer passed in. Reported-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Mark Brown authored
commit b763ec17 upstream. If a read is attempted which is smaller than the line length then we may underflow the subtraction we're doing with the unsigned size_t type so move some of the calculation to be additions on the right hand side instead in order to avoid this. Reported-by:
-
Peter Zijlstra authored
commit 275d7d44 upstream. Poma (on the way to another bug) reported an assertion triggering: [<ffffffff81150529>] module_assert_mutex_or_preempt+0x49/0x90 [<ffffffff81150822>] __module_address+0x32/0x150 [<ffffffff81150956>] __module_text_address+0x16/0x70 [<ffffffff81150f19>] symbol_put_addr+0x29/0x40 [<ffffffffa04b77ad>] dvb_frontend_detach+0x7d/0x90 [dvb_core] Laura Abbott <labbott@redhat.com> produced a patch which lead us to inspect symbol_put_addr(). This function has a comment claiming it doesn't need to disable preemption around the module lookup because it holds a reference to the module it wants to find, which therefore cannot go away. This is wrong (and a false optimization too, preempt_disable() is really rather cheap, and I doubt any of this is on uber critical paths, otherwise it would've retained a pointer to the actual module anyway and avoided the second lookup). While its true that the module cannot go away while we hold a reference on it, the data structure we do the lookup in very much _CAN_ change while we do the lookup. Therefore fix the comment and add the required preempt_disable(). Reported-by:
poma <pomidorabelisima@gmail.com> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Fixes: a6e6abd5 ("module: remove module_text_address()") Signed-off-by:
-
Ben Hutchings authored
This reverts commit 41e3025e, which was commit 6f691251 upstream. The fix is only needed after commit f8f55942 ("KVM: MMU: fast invalidate all mmio sptes"), included in Linux 3.11. Signed-off-by:
-
- 13 Oct, 2015 13 commits
-
-
Ben Hutchings authored
-
Ben Hutchings authored
This reverts commit 117b8a10, which was commit 29c4afc4 upstream. The bug it fixes upstream clearly doesn't exist in 3.2. Signed-off-by:
-
Jan Kara authored
commit 841df7df upstream. Commit 6f6a6fda "jbd2: fix ocfs2 corrupt when updating journal superblock fails" changed jbd2_cleanup_journal_tail() to return EIO when the journal is aborted. That makes logic in jbd2_log_do_checkpoint() bail out which is fine, except that jbd2_journal_destroy() expects jbd2_log_do_checkpoint() to always make a progress in cleaning the journal. Without it jbd2_journal_destroy() just loops in an infinite loop. Fix jbd2_journal_destroy() to cleanup journal checkpoint lists of jbd2_log_do_checkpoint() fails with error. Reported-by:
Eryu Guan <guaneryu@gmail.com> Tested-by:
Jan Kara <jack@suse.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Helge Deller authored
commit b1b4e435 upstream. When detecting a serial port on newer PA-RISC machines (with iosapic) we have a long way to go to find the right IRQ line, registering it, then registering the serial port and the irq handler for the serial port. During this phase spurious interrupts for the serial port may happen which then crashes the kernel because the action handler might not have been set up yet. So, basically it's a race condition between the serial port hardware and the CPU which sets up the necessary fields in the irq sructs. The main reason for this race is, that we unmask the serial port irqs too early without having set up everything properly before (which isn't easily possible because we need the IRQ number to register the serial ports). This patch is a work-around for this problem. It adds checks to the CPU irq handler to verify if the IRQ action field has been initialized already. If not, we just skip this interrupt (which isn't critical for a serial port at bootup). The real fix would probably involve rewriting all PA-RISC specific IRQ code (for CPU, IOSAPIC, GSC and EISA) to use IRQ domains with proper parenting of the irq chips and proper irq enabling along this line. This bug has been in the PA-RISC port since the beginning, but the crashes happened very rarely with currently used hardware. But on the latest machine which I bought (a C8000 workstation), which uses the fastest CPUs (4 x PA8900, 1GHz) and which has the largest possible L1 cache size (64MB each), the kernel crashed at every boot because of this race. So, without this patch the machine would currently be unuseable. For the record, here is the flow logic: 1. serial_init_chip() in 8250_gsc.c calls iosapic_serial_irq(). 2. iosapic_serial_irq() calls txn_alloc_irq() to find the irq. 3. iosapic_serial_irq() calls cpu_claim_irq() to register the CPU irq 4. cpu_claim_irq() unmasks the CPU irq (which it shouldn't!) 5. serial_init_chip() then registers the 8250 port. Problems: - In step 4 the CPU irq shouldn't have been registered yet, but after step 5 - If serial irq happens between 4 and 5 have finished, the kernel will crash Cc: linux-parisc@vger.kernel.org Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Michal Kubeček authored
commit 49a18d86 upstream. As pointed out by Eric Dumazet, net->ipv6.ip6_rt_last_gc should hold the last time garbage collector was run so that we should update it whenever fib6_run_gc() calls fib6_clean_all(), not only if we got there from ip6_dst_gc(). Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
Michal Kubeček authored
commit 2ac3ac8f upstream. On a high-traffic router with many processors and many IPv6 dst entries, soft lockup in fib6_run_gc() can occur when number of entries reaches gc_thresh. This happens because fib6_run_gc() uses fib6_gc_lock to allow only one thread to run the garbage collector but ip6_dst_gc() doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc() returns. On a system with many entries, this can take some time so that in the meantime, other threads pass the tests in ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for the lock. They then have to run the garbage collector one after another which blocks them for quite long. Resolve this by replacing special value ~0UL of expire parameter to fib6_run_gc() by explicit "force" parameter to choose between spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with force=false if gc_thresh is reached but not max_size. Signed-off-by:
-
Kirill A. Shutemov authored
commit 575bf1d0 upstream. perl.h from new Perl release doesn't like -Wundef and -Wswitch-default: /usr/lib/perl5/core_perl/CORE/perl.h:548:5: error: "SILENT_NO_TAINT_SUPPORT" is not defined [-Werror=undef] #if SILENT_NO_TAINT_SUPPORT && !defined(NO_TAINT_SUPPORT) ^ /usr/lib/perl5/core_perl/CORE/perl.h:556:5: error: "NO_TAINT_SUPPORT" is not defined [-Werror=undef] #if NO_TAINT_SUPPORT ^ In file included from /usr/lib/perl5/core_perl/CORE/perl.h:3471:0, from util/scripting-engines/trace-event-perl.c:30: /usr/lib/perl5/core_perl/CORE/sv.h:1455:5: error: "NO_TAINT_SUPPORT" is not defined [-Werror=undef] #if NO_TAINT_SUPPORT ^ In file included from /usr/lib/perl5/core_perl/CORE/perl.h:3472:0, from util/scripting-engines/trace-event-perl.c:30: /usr/lib/perl5/core_perl/CORE/regexp.h:436:5: error: "NO_TAINT_SUPPORT" is not defined [-Werror=undef] #if NO_TAINT_SUPPORT ^ In file included from /usr/lib/perl5/core_perl/CORE/hv.h:592:0, from /usr/lib/perl5/core_perl/CORE/perl.h:3480, from util/scripting-engines/trace-event-perl.c:30: /usr/lib/perl5/core_perl/CORE/hv_func.h: In function ‘S_perl_hash_siphash_2_4’: /usr/lib/perl5/core_perl/CORE/hv_func.h:222:3: error: switch missing default case [-Werror=switch-default] switch( left ) ^ /usr/lib/perl5/core_perl/CORE/hv_func.h: In function ‘S_perl_hash_superfast’: /usr/lib/perl5/core_perl/CORE/hv_func.h:274:5: error: switch missing default case [-Werror=switch-default] switch (rem) { \ ^ /usr/lib/perl5/core_perl/CORE/hv_func.h: In function ‘S_perl_hash_murmur3’: /usr/lib/perl5/core_perl/CORE/hv_func.h:398:5: error: switch missing default case [-Werror=switch-default] switch(bytes_in_carry) { /* how many bytes in carry */ ^ Let's disable the warnings for code which uses perl.h. Signed-off-by:
Kirill A. Shutemov <kirill@shutemov.name> Cc: Ingo Molnar <mingo@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1372063394-20126-1-git-send-email-kirill@shutemov.nameSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Wilson Kok authored
[ Upstream commit 41fc0143 ] dump_rules returns skb length and not error. But when family == AF_UNSPEC, the caller of dump_rules assumes that it returns an error. Hence, when family == AF_UNSPEC, we continue trying to dump on -EMSGSIZE errors resulting in incorrect dump idx carried between skbs belonging to the same dump. This results in fib rule dump always only dumping rules that fit into the first skb. This patch fixes dump_rules to return error so that we exit correctly and idx is correctly maintained between skbs that are part of the same dump. Signed-off-by:
Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
-
Richard Laing authored
[ Upstream commit 25b4a44c ] In the IPv6 multicast routing code the mrt_lock was not being released correctly in the MFC iterator, as a result adding or deleting a MIF would cause a hang because the mrt_lock could not be acquired. This fix is a copy of the code for the IPv4 case and ensures that the lock is released correctly. Signed-off-by:
Richard Laing <richard.laing@alliedtelesis.co.nz> Acked-by:
Cong Wang <cwang@twopensource.com> Signed-off-by:
-
dingtianhong authored
[ Upstream commit a951bc1e ] The "follow" fail_over_mac policy is useful for multiport devices that either become confused or incur a performance penalty when multiple ports are programmed with the same MAC address, but the same MAC address still may happened by this steps for this policy: 1) echo +eth0 > /sys/class/net/bond0/bonding/slaves bond0 has the same mac address with eth0, it is MAC1. 2) echo +eth1 > /sys/class/net/bond0/bonding/slaves eth1 is backup, eth1 has MAC2. 3) ifconfig eth0 down eth1 became active slave, bond will swap MAC for eth0 and eth1, so eth1 has MAC1, and eth0 has MAC2. 4) ifconfig eth1 down there is no active slave, and eth1 still has MAC1, eth2 has MAC2. 5) ifconfig eth0 up the eth0 became active slave again, the bond set eth0 to MAC1. Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same MAC address, it will break this policy for ACTIVE_BACKUP mode. This patch will fix this problem by finding the old active slave and swap them MAC address before change active slave. Signed-off-by:
Ding Tianhong <dingtianhong@huawei.com> Tested-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 03645a11 ] ip6_datagram_connect() is doing a lot of socket changes without socket being locked. This looks wrong, at least for udp_lib_rehash() which could corrupt lists because of concurrent udp_sk(sk)->udp_portaddr_hash accesses. Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Herbert Xu authored
[ Upstream commit 89c22d8c ] When we calculate the checksum on the recv path, we store the result in the skb as an optimisation in case we need the checksum again down the line. This is in fact bogus for the MSG_PEEK case as this is done without any locking. So multiple threads can peek and then store the result to the same skb, potentially resulting in bogus skb states. This patch fixes this by only storing the result if the skb is not shared. This preserves the optimisations for the few cases where it can be done safely due to locking or other reasons, e.g., SIOCINQ. Signed-off-by:
-
Oleg Nesterov authored
[ Upstream commit fecdf8be ] pktgen_thread_worker() is obviously racy, kthread_stop() can come between the kthread_should_stop() check and set_current_state(). Signed-off-by:
Jan Stancek <jstancek@redhat.com> Reported-by:
Marcelo Leitner <mleitner@redhat.com> Signed-off-by:
-
