- 07 Apr, 2017 1 commit
-
-
Fam Zheng authored
If device reports a small max_xfer_blocks and a zero opt_xfer_blocks, we end up using BLK_DEF_MAX_SECTORS, which is wrong and r/w of that size may get error. [mkp: tweaked to avoid setting rw_max twice and added typecast] Cc: <stable@vger.kernel.org> # v4.4+ Fixes: ca369d51 ("block/sd: Fix device-imposed transfer length limits") Signed-off-by:
Fam Zheng <famz@redhat.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
- 28 Mar, 2017 1 commit
-
-
Jaehoon Chung authored
There are same conditions for checking whether supporting clkscaling or not. When ufshcd is supporting clkscaling, active_reqs should be decreased by one. [mkp: addressed comment from Bartlomiej] Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
-
- 23 Mar, 2017 3 commits
-
-
Arnd Bergmann authored
On a randconfig build without CONFIG_SCSI_LPFC_DEBUG_FS, I ran into multiple compile failures: drivers/scsi/lpfc/lpfc_debugfs.h: In function 'lpfc_debug_dump_wq': drivers/scsi/lpfc/lpfc_debugfs.h:405:15: error: 'DUMP_FCP' undeclared (first use in this function); did you mean 'DUMP_VAR'? drivers/scsi/lpfc/lpfc_debugfs.h:405:15: note: each undeclared identifier is reported only once for each function it appears in drivers/scsi/lpfc/lpfc_debugfs.h:408:22: error: 'DUMP_NVME' undeclared (first use in this function); did you mean 'DUMP_NONE'? drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_ls_rsp_cmp': drivers/scsi/lpfc/lpfc_nvmet.c:109:2: error: implicit declaration of function 'lpfc_nvmeio_data'; did you mean 'lpfc_mem_free'? [-Werror=implicit-function-declaration] drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_fcp_op': drivers/scsi/lpfc/lpfc_nvmet.c:523:10: error: unused variable 'id' [-Werror=unused-variable] They are all trivial to fix, so I'm doing it in a combined patch here. Fixes: 1d9d5a98 ("scsi: lpfc: refactor debugfs queue dump routines") Fixes: bd2cdd5e ("scsi: lpfc: NVME Initiator: Add debugfs support") Fixes: 2b65e182 ("scsi: lpfc: NVME Target: Add debugfs support") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
-
Dick Kennedy authored
lpfc cannot establish connection with targets that send PRLI in P2P configurations. If lpfc rejects a PRLI that is sent from a target the target will not resend and will reject the PRLI send from the initiator. [mkp: applied by hand] Signed-off-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
-
Tomas Henzl authored
In a previous patch a hpsa_scsi_dev_t.volume_offline update line has been removed, so let us put it back.. Fixes: 85b29008 (hpsa: update check for logical volume status) Signed-off-by:
Tomas Henzl <thenzl@redhat.com> Acked-by:
Don Brace <don.brace@microsemi.com> Signed-off-by:
-
- 20 Mar, 2017 1 commit
-
-
John Garry authored
The total ata xfer length may not be calculated properly, in that we do not use the proper method to get an sg element dma length. According to the code comment, sg_dma_len() should be used after dma_map_sg() is called. This issue was found by turning on the SMMUv3 in front of the hisi_sas controller in hip07. Multiple sg elements were being combined into a single element, but the original first element length was being use as the total xfer length. Cc: <stable@vger.kernel.org> Fixes: ff2aeb1e ("libata: convert to chained sg") Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
-
- 19 Mar, 2017 3 commits
-
-
Bart Van Assche authored
Callers must provide a valid port group to alua_rtpg_queue(). Issue a kernel warning if that is not the case. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Bart Van Assche authored
Callers of scsi_dh_activate(), e.g. dm-mpath, assume that this function either returns an error code or calls the completion function. Make alua_activate() call the completion function even if scsi_device_get() fails. Signed-off-by:
-
Bart Van Assche authored
Do not queue ALUA work nor call scsi_device_put() if the scsi_device_get() call fails. This patch fixes the following crash: general protection fault: 0000 [#1] SMP RIP: 0010:scsi_device_put+0xb/0x30 Call Trace: scsi_disk_put+0x2d/0x40 sd_release+0x3d/0xb0 __blkdev_put+0x29e/0x360 blkdev_put+0x49/0x170 dm_put_table_device+0x58/0xc0 [dm_mod] dm_put_device+0x70/0xc0 [dm_mod] free_priority_group+0x92/0xc0 [dm_multipath] free_multipath+0x70/0xc0 [dm_multipath] multipath_dtr+0x19/0x20 [dm_multipath] dm_table_destroy+0x67/0x120 [dm_mod] dev_suspend+0xde/0x240 [dm_mod] ctl_ioctl+0x1f5/0x520 [dm_mod] dm_ctl_ioctl+0xe/0x20 [dm_mod] do_vfs_ioctl+0x8f/0x700 SyS_ioctl+0x3c/0x70 entry_SYSCALL_64_fastpath+0x18/0xad Fixes: commit 03197b61 ("scsi_dh_alua: Use workqueue for RTPG") Signed-off-by:
-
- 16 Mar, 2017 1 commit
-
-
peter chang authored
The user can control the size of the next command passed along, but the value passed to the ioctl isn't checked against the usable max command size. Cc: <stable@vger.kernel.org> Signed-off-by:
Peter Chang <dpf@google.com> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
- 15 Mar, 2017 9 commits
-
-
Tomas Winkler authored
IS_ERR and ERR_PTR already forcefully cast their argument, hence there is no need for additional (complex) casting. Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Reviewed-by:
-
Manish Rangankar authored
Signed-off-by:
Manish Rangankar <manish.rangankar@cavium.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
Currently, command threads fails to return ioctls commands for older controller versions, since it returns when all the fibs have been allocated. Another issue is even all the fibs have not been allocated, the correct allocated fibs is not updated nor freed. Fixes: 113156bc (scsi: aacraid: Reworked aac_command_thread) Reported-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
Dave Carroll <david.carroll@microsemi.com> Signed-off-by:
-
Bill Kuzeja authored
After a Qlogic card breaks when initializing (test case), the system can crash in qla2xxx_eh_abort if processing anything but a scsi command type srb. Fixes: 1535aa75 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove") Signed-off-by:
Bill Kuzeja <william.kuzeja@stratus.com> Acked-By:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
-
James Smart authored
Reviewing the result of what was just added for Kconfig, we made a poor choice. It worked well for full kernel builds, but not so much for how it would be deployed on a distro. Here's the final result: - lpfc will compile in NVME initiator and/or NVME target support based on whether the kernel has the corresponding subsystem support. Kconfig is not used to drive this specifically for lpfc. - There is a module parameter, lpfc_enable_fc4_type, that indicates whether the ports will do FCP-only or FCP & NVME (NVME-only not yet possible due to dependency on fc transport). As FCP & NVME divvys up exchange resources, and given NVME will not be often initially, the default is changed to FCP only. Signed-off-by:
-
Tomas Winkler authored
Fix compilation warning: drivers/scsi/ufs/ufshcd.c:7645:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits] if ((value < UFS_PM_LVL_0) || (value >= UFS_PM_LVL_MAX)) Signed-off-by:
-
Don Brace authored
Resets can take longer than DEFAULT_TIMEOUT. Reviewed-by:
Scott Benesh <scott.benesh@microsemi.com> Reviewed-by:
Scott Teel <scott.teel@microsemi.com> Reviewed-by:
-
Don Brace authored
Avoid rescan storms. No need to queue another if one is pending. Reviewed-by:
-
Don Brace authored
- Add in a new case for volume offline. Resolves internal testing bug for multilun array management. - Return correct status for failed TURs. Reviewed-by:
-
- 14 Mar, 2017 4 commits
-
-
Shivasharan S authored
Signed-off-by:
Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by:
Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by:
-
Shivasharan S authored
Without this fix, raid6 performance will not be optimal. Signed-off-by:
-
Shivasharan S authored
Return value check of atomic_dec_if_positive is required as it returns old value minus one. Without this fix, driver will send small ios to firmware path and that will be a performance issue. Not critical, but good to have r1_ldio_hint as default value in sdev private. Signed-off-by:
-
Shivasharan S authored
Without this fix, driver will enable INTx Interrupt pin even though MSI-x vectors are enabled. See below lspci output. DisINTx is unset for MSIx setup. lspci -s 85:00.0 -vvv |grep INT |grep Control Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- After applying this fix, driver will enable INTx Interrupt pin only if Legacy interrupt method is required. See below lspci output. DisINTx is set for MSIx setup. lspci -s 85:00.0 -vvv |grep INT |grep Control Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Signed-off-by:
-
- 08 Mar, 2017 2 commits
-
-
Anton Blanchard authored
We see lpfc devices regularly fail during kexec. Fix this by adding a shutdown method which mirrors the remove method. Cc: <stable@vger.kernel.org> Signed-off-by:
Anton Blanchard <anton@samba.org> Reviewed-by:
Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Tested-by:
-
Stephen Hemminger authored
Hyper-V host emulation of SCSI for virtual DVD device reports SCSI version 0 (UNKNOWN) but is still capable of supporting REPORTLUN. Without this patch, a GEN2 Linux guest on Hyper-V will not boot 4.11 successfully with virtual DVD ROM device. What happens is that the SCSI scan process falls back to doing sequential probing by INQUIRY. But the storvsc driver has a previous workaround that masks/blocks all errors reports from INQUIRY (or MODE_SENSE) commands. This workaround causes the scan to then populate a full set of bogus LUN's on the target and then sends kernel spinning off into a death spiral doing block reads on the non-existent LUNs. By setting the correct blacklist flags, the target with the DVD device is scanned with REPORTLUN and that works correctly. Patch needs to go in current 4.11, it is safe but not necessary in older kernels. Signed-off-by:
Stephen Hemminger <sthemmin@microsoft.com> Reviewed-by:
K. Y. Srinivasan <kys@microsoft.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
- 07 Mar, 2017 15 commits
-
-
James Smart authored
Revise lpfc version number to 11.2.0.10 Signed-off-by:
-
James Smart authored
This patch addresses the smatch issues identified by Dan Carpenter in http://www.spinics.net/lists/linux-scsi/msg105665.html The issues are: drivers/scsi/lpfc/lpfc_ct.c:943 lpfc_cmpl_ct_cmd_gft_id() error: we previously assumed 'ndlp' could be null (see line 928) Action: moved under if check drivers/scsi/lpfc/lpfc_nvmet.c:1694 lpfc_nvmet_unsol_issue_abort() error: we previously assumed 'ndlp' could be null (see line 1690) Action: conditionalized arg in printf stmt drivers/scsi/lpfc/lpfc_nvmet.c:1792 lpfc_nvmet_sol_fcp_issue_abort() error: we previously assumed 'ndlp' could be null (see line 1788) Action: conditionalized arg in printf stmt Signed-off-by:
-
James Smart authored
This patch addresses the smatch issues identified by Dan Carpenter in http://www.spinics.net/lists/linux-scsi/msg105663.html The issues are: drivers/scsi/lpfc/lpfc_hbadisc.c:316 lpfc_dev_loss_tmo_handler() warn: we tested 'vport->load_flag & 2' before and it was 'false' Action: removed item from test drivers/scsi/lpfc/lpfc_hbadisc.c:701 lpfc_work_done() warn: test_bit() takes a bit number Action: changed definition so bit number drivers/scsi/lpfc/lpfc_hbadisc.c:2206 lpfc_mbx_cmpl_fcf_scan_read_fcf_rec() error: uninitialized symbol 'vlan_id'. drivers/scsi/lpfc/lpfc_hbadisc.c:2582 lpfc_mbx_cmpl_fcf_rr_read_fcf_rec() error: uninitialized symbol 'vlan_id'. drivers/scsi/lpfc/lpfc_hbadisc.c:2683 lpfc_mbx_cmpl_read_fcf_rec() error: uninitialized symbol 'vlan_id'. Action: initilized value drivers/scsi/lpfc/lpfc_hbadisc.c:4025 lpfc_register_remote_port() error: we previously assumed 'rdata' could be null (see line 4023) Action: refactored check block drivers/scsi/lpfc/lpfc_hbadisc.c:4613 lpfc_sli4_dequeue_nport_iocbs() error: double unlock 'irq:' Action: removed inner irq reference Signed-off-by:
-
James Smart authored
NVME merge reverted diag port names to the physical port. They should be the vport. Signed-off-by:
-
James Smart authored
Remove nvme teardown calls that should not be there on sli3 devices Signed-off-by:
-
James Smart authored
Correct a merge error that had debug data printed twice for the same element Signed-off-by:
-
James Smart authored
Without apriori understanding of what the define is, the name gives a very different impression of what it is (a max delay value for an EQ). Rename the define so it reflects what it is: the number of EQ IDs that can be set in one instance of the MODIFY_EQ_DELAY mbx command. Signed-off-by:
-
James Smart authored
Reworked Kconfig so that lfpc only requires the scsi stack. NVME Initiator and NVME Target support can be enabled if the other NVMe subsystems have been enabled. Signed-off-by:
-
James Smart authored
Christoph's prior patch missed the template for the sli3 adapters, which is now the "no host reset" template. Add the transport eh_timed_out handler to the no host reset template Signed-off-by:
-
James Smart authored
A previous change unilaterally removed the hba reset entry point from the sli3 host template. This was done to allow tape devices being used for back up from being removed. Why was this done ? When there was non-responding device on the fabric, the error escalation policy would escalate to the reset handler. When the reset handler was called, it would reset the adapter, dropping link, thus logging out and terminating all i/o's - on any target. If there was a tape device on the same adapter that wasn't in error, it would kill the tape i/o's, effectively killing the tape device state. With the reset point removed, the adapter reset avoided the fabric logout, allowing the other devices to continue to operate unaffected. A hack - yes. Hint: we really need a transport I_T nexus reset callback added to the eh process (in between the SCSI target reset and hba reset points), so a fc logout could occur to the one bad target only and stop the error escalation process. This patch commonizes the approach so it can be used for sli3 and sli4 adapters, but mandates the admin, via module parameter, specifically identify which adapters the resets are to be removed for. Additionally, bus_reset, which sends Target Reset TMFs to all targets, is also removed from the template as it too has the same effect as the adapter reset. Signed-off-by:
Laurence Oberman <loberman@redhat.com> Tested-by:
-
James Smart authored
previous code did little more than log a message. This patch adds abort path support, modeled after the SCSI code paths. Currently addresses only the initiator path. Target path under development, but stubbed out. Signed-off-by:
-
James Smart authored
nvme bufs get allocated even when the registration fails. Move allocation into the rsgistration success path. Signed-off-by:
-
James Smart authored
For both initiator and target: if WQ is full, return -EBUSY. Signed-off-by:
-
James Smart authored
Word 1 in NVME CMD IU appears byte swapped from value placed in WQE Should be Big Endian value in WQE word 16 Signed-off-by:
-
James Smart authored
NVME LS requests and responses had wrong R_CTL values. Use the FC4 ELS Request and Response defines (defines badly named, they are FC4 LS's) instead of the base ELS values. Signed-off-by:
-
