Follow the comment style of mode0_name.modeX_name for pins
which mux mode differs from MUX_MODE0.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the IO chain reconfigure fixed, we can now enable the PMIC
scripts for LDP.

Note that at least on my es3.0 based LDP, the UART seems to be
flakey after wake-up events from off-idle and hangs but eventually
continues.
Signed-off-by: Tony Lindgren <tony@atomide.com>

As we have support for this in board-rx51-peripherals.c, let's
add it to the .dts files too.

Note that the reset GPIO will eventually go to the driver.
For now let's just pull it down and skip any further reset
in case the bootloader has configured the MAC address so
NFSroot works.

Also note that after 3430-sdp are using proper GPMC timings
we can remove the tests for smsc,lan91c94 in gpmc.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>

There are external pulls on these lines and enabling the
internal pulls can cause issue. This is because the internal
pulls are parallel with the external pulls. So let's clear
the internal I2C pulls.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is no longer needed as the device specific wake-up event
can now be specified with interrupts-extended property where
the second interrupt is the pinctrl-single register, such as
the UART3 RX pin.

Note that twl4030_omap3.dtsi needs to set WAKEUPENABLE for
off-idle to properly trigger the PMIC scripts. And GPIO pins
still need to set WAKEUPENABLE for wake-up events.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Compared to legacy booting, we don't have wake-up events enabled
for device tree based booting. This means that if deeper idle
states are enabled, the device won't wake up to UART events and
seems like it has hung.

Let's fix that by adding the wake-up interrupt. Note that we
don't need to set the PIN_OFF_WAKEUPENABLE any longer, that's
handled by the wake-up interrupt when the serial driver does
request_irq on it.

Tested with the following on omap3-overo-summit that has the
ES2.1 omap:

#!/bin/bash

uarts=$(find /sys/class/tty/ttyO*/device/power/ -type d)
for uart in $uarts; do
        echo 3000 > $uart/autosuspend_delay_ms
done

uarts=$(find /sys/class/tty/ttyO*/power/ -type d)
for uart in $uarts; do
        echo enabled > $uart/wakeup
        echo auto > $uart/control
done

echo 1 > /sys/kernel/debug/pm_debug/enable_off_mode

# grep -i uart /proc/interrupts
 90:       1085      INTC  74  OMAP UART2
338:          5   pinctrl 366  OMAP UART2

# grep ^core_pwrdm /sys/kernel/debug/pm_debug/count
core_pwrdm (ON),OFF:1654,RET:131,INA:39,ON:1825...
Signed-off-by: Tony Lindgren <tony@atomide.com>

The sub-mailbox devices are added to the Mailbox DT nodes on
OMAP2420, OMAP2430, OMAP3, AM33xx, AM43xx, OMAP4 and OMAP5
family of SoCs. This data represents the same mailboxes that
used to be represented in hwmod attribute data previously.
The node name is chosen based on the .name field of
omap_mbox_dev_info structure used in the hwmod data.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge branch 'pull/v3.18/for-dt-pinctrl-updates' of https://github.com/nmenon/linux-2.6-playground into omap-for-v3.18/dt

Mark rxd as wakeupcapable for 115200n8 no hardware-flow control
configuration. If h/w flow control is being used, then rts/cts
appropriately should be used.
Signed-off-by: Nishanth Menon <nm@ti.com>

We've had deeper idle states working on omaps for few years now,
but only in the legacy mode. When booted with device tree, the
wake-up events did not have a chance to work until commit
3e6cee17 ("pinctrl: single: Add support for wake-up interrupts")
that recently got merged. In addition to that we also needed
commit 79d97015 ("of/irq: create interrupts-extended property")
that's now also merged.

Note that there's no longer need to specify the wake-up bit in
the pinctrl settings, the request_irq on the wake-up pin takes
care of that.
Signed-off-by: Nishanth Menon <nm@ti.com>

Now that ti,am437-padconf is available, switch over to that compatible
property. Retain pinctrl-single for legacy support.

While at it, mark the pinctrl as interrupt controller so that it can
be used with interrupts-extended property for wakeup events.
Signed-off-by: Nishanth Menon <nm@ti.com>

Now that ti,dra7-padconf is available, switch over to that compatible
property. Retain pinctrl-single for legacy support.

While at it, mark pinctrl as interrupt controller so that it can be used
with interrupts-extended property for wakeup events.
Signed-off-by: Nishanth Menon <nm@ti.com>

Now that ti,omap5-padconf is available, switch over to that compatible
property. Retain pinctrl-single for legacy support.

While at it, mark pinctrl as interrupt controller so that it can be
used with interrupts-extended property for wakeup events.
Signed-off-by: Nishanth Menon <nm@ti.com>

Add regulator-name properties for the regulators that don't have them,
allowing the kernel to display the name from the schematic rather than
the name of the regulator on the PMIC in order to improve diagnostics.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

CM-T54 CoM can be used with various custom baseboards, other
than SB-T54 (supplied with SBC-T54 single board computer).

Update model property of SBC-T54 DT to clarify this.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The RFBI node for OMAP DSS was left out when adding the rest of the DSS
nodes, because it was not clear how to set up the clocks for the RFBI.

However, it seems that if there is a HWMOD for a device, we also need a
DT node for it. Otherwise, at boot, we get:

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2542 _init+0x464/0x4e0()
omap_hwmod: dss_rfbi: doesn't have mpu register target base

Now that v3.17-rc3 contains a fix 8fd46439 ("ARM: dts:
omap54xx-clocks: Fix the l3 and l4 clock rates") for the L3 ICLK
required by the RFBI, let's add the RFBI node to get rid of the
warning.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated description per comments from Nishant]
Signed-off-by: Tony Lindgren <tony@atomide.com>

These baseboards are equipped with the Technexion TAO35030 SOM. So
they include this dtsi. The common parts are extracted into an "common"
dtsi file. The main difference between both boards is, that the *lcd
has DSS support enabled for the LCD.

Some HEAD acoustics specific features are:

- LED handling
- Special FPGA/DSP audio driver (not included in this series)
- powerdown GPIO
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This baseboard is equipped with the Technexion TAO35030 SOM. So
includes this dtsi. Some Thunder specific features are:

- LCD panel
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Technexion TAO3530 is a OMAP3530 based SOM. This patch adds the
basic support for it as an dtsi file which can be included by
baseboard equipped with this SOM. E.g. the Technexion Thunder
baseboard.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Set internal clock source for MMC2 on tao3530.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM57xx processor family are variants of DRA7 family of processors and
targetted at industrial and non-automotive applications.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

DRA72x-evm uses TPS65917 PMIC. Add the node.

NOTE: LDO2 is actually unused, but the usage if any is expected to be
between 1.8 to 3.3v IO voltage. So define the node.

NOTE: Interrupt used is crossbar number based.
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

I2C1 bus is used for the following peripherals
	P8 connector (MLB)
	TLV320AIC3106 Audio codec
	J15 LCD header
	24WC256 eeprom
	TMP102AIDRLT temperature sensor
	PCF8575 GPIO expander
	PCA9306 i2c voltage translator -> Goes to P9 for comm interface
	P2 expansion connector
	TPS65917 PMIC

The slowest speed of all the peripherals seems to be 400KHz.
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge the gta04 related changes that were too late for v3.17

Pull Xtensa updates from Chris Zankel:
 "Xtensa improvements for 3.17:
   - support highmem on cores with aliasing data cache.  Enable highmem
     on kc705 by default
   - simplify addition of new core variants (no need to modify Kconfig /
     Makefiles)
   - improve robustness of unaligned access handler and its interaction
     with window overflow/underflow exception handlers
   - deprecate atomic and spill registers syscalls
   - clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
     statements
   - wire up renameat2 syscall.

  Various fixes:
   - fix address checks in dma_{alloc,free}_coherent (runtime BUG)
   - fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
   - fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
     (runtime unrecoverable exception)
   - fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
     register clobbering)
   - fix kernel/user jump out of fast_unaligned (potential runtime
     unrecoverabl exception)
   - replace termios IOCTL code definitions with constants (userspace
     build breakage)"

* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
  xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
  xtensa: don't allow overflow/underflow on unaligned stack
  xtensa: fix a6 and a7 handling in fast_syscall_xtensa
  xtensa: allow single-stepping through unaligned load/store
  xtensa: move invalid unaligned instruction handler closer to its users
  xtensa: make fast_unaligned store restartable
  xtensa: add double exception fixup handler for fast_unaligned
  xtensa: fix kernel/user jump out of fast_unaligned
  xtensa: configure kc705 for highmem
  xtensa: support highmem in aliasing cache flushing code
  xtensa: support aliasing cache in kmap
  xtensa: support aliasing cache in k[un]map_atomic
  xtensa: implement clear_user_highpage and copy_user_highpage
  xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
  xtensa: allow fixmap and kmap span more than one page table
  xtensa: make fixmap region addressing grow with index
  xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
  xtensa: add renameat2 syscall
  xtensa: fix address checks in dma_{alloc,free}_coherent
  xtensa: replace IOCTL code definitions with constants
  ...

unicore32 builds fail with

  arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
  arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
  arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
  arch/unicore32/kernel/signal.c: In function ‘do_signal’:
  arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
  make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
  make: *** [arch/unicore32/kernel/signal.o] Error 2

Bisect points to commit 649671c9 ("unicore32: Use get_signal()
signal_setup_done()").

This code never even compiled.  Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up.  Compile
tested only.

Fixes: 649671c9 ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM fixes from Russell King:
 "Various assorted fixes:

   - a couple of patches from Mark Rutland to resolve an errata with
     Cortex-A15 CPUs.
   - fix cpuidle for the CPU part ID changes in the last merge window
   - add support for a relocation which ARM binutils is generating in
     some circumstances"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
  ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
  ARM: 8128/1: abort: don't clear the exclusive monitors
  ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations

Pull ARM SoC fixes from Olof Johansson:
 "Here's the weekly batch of fixes from arm-soc.

  The delta is a largeish negative delta, due to revert of SMP support
  for Broadcom's STB SoC -- it was accidentally merged before some
  issues had been addressed, so they will make a new attempt for 3.18.
  I didn't see a need for a full revert of the whole platform due to
  this, we're keeping the rest enabled.

  The rest is mostly:

   - a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
   - some MTD/NAND fixes for OMAP
   - minor DT fixes for shmobile
   - warning fix for UP builds on vexpress/spc

  There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
  so it can boot.  Drivers and the rest had landed for 3.17, and it's
  small and isolated so it made sense to pick up now even if it's not a
  bugfix"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  vexpress/spc: fix a build warning on array bounds
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
  MAINTAINERS: catch special Rockchip code locations
  ARM: dts: microsom-ar8035: MDIO pad must be set open drain
  ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
  ARM: brcmstb: revert SMP support
  ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
  ARM: dts: Enable UART wake-up events for beagleboard
  ARM: dts: Remove twl6030 clk32g "regulator"
  ARM: OMAP2+: omap_device: remove warning that clk alias already exists
  ARM: OMAP: fix %d confusingly prefixed with 0x in format string
  ARM: dts: DRA7: fix interrupt-cells for GPIO
  mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
  ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
  ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
  mtd: nand: omap: Revert to using software ECC by default
  ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
  ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
  ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
  ...

With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:

arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
  struct ve_spc_opp *opps = info->opps[cluster];
                                      ^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:

Add basic subarchitecture support for the DRA72x and DRA74x.  These
are OMAP2+ derivative SoCs.  This should be low-risk to existing OMAP
platforms.

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/

* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull spi bugfixes from Mark Brown:
 "A smattering of bug fixes for the SPI subsystem, all in driver code
  which has seen active work recently and none of them with any great
  global impact.

  There's also a new ACPI ID for the pxa2xx driver which required no
  code changes and the addition of kerneldoc for some structure fields
  that were missing it and generating warnings during documentation
  builds as a result"

* tag 'spi-v3.17-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: sh-msiof: Fix transmit-only DMA transfers
  spi/rockchip: Avoid accidentally turning off the clock
  spi: dw: fix kernel crash due to NULL pointer dereference
  spi: dw-pci: fix bug when regs left uninitialized
  spi: davinci: fix SPI_NO_CS functionality
  spi/rockchip: fixup incorrect dma direction setting
  spi/pxa2xx: Add ACPI ID for Intel Braswell
  spi: spi-au1550: fix build failure
  spi: rspi: Fix leaking of unused DMA descriptors
  spi: sh-msiof: Fix leaking of unused DMA descriptors
  spi: Add missing kerneldoc bits
  spi/omap-mcspi: Fix the spi task hangs waiting dma_rx

spi: Bug fixes for v3.17

A smattering of bug fixes for the SPI subsystem, all in driver code
which has seen active work recently and none of them with any great
global impact.

There's also a new ACPI ID for the pxa2xx driver which required no code
changes and the addition of kerneldoc for some structure fields that
were missing it and generating warnings during documentation builds as a
result.

# gpg: Signature made Sun 31 Aug 2014 13:19:12 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg:                 aka "Mark Brown <broonie@debian.org>"
# gpg:                 aka "Mark Brown <broonie@kernel.org>"
# gpg:                 aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg:                 aka "Mark Brown <broonie@linaro.org>"
# gpg:                 aka "Mark Brown <Mark.Brown@linaro.org>"

Fix tx/rx mixup, which broke transmit-only transfers.

Introduced by commit 4240305f7cbdc7782aa8bc40cc702775d9ac0839
("spi: sh-msiof: Fix leaking of unused DMA descriptors").
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Pull file locking bugfx from Jeff Layton:
 "Just a bugfix for a bug that crept in to v3.15.  It's in a rather rare
  error path, and I'm not aware of anyone having hit it, but it's worth
  fixing for v3.17"

* tag 'locks-v3.17-3' of git://git.samba.org/jlayton/linux:
  locks: pass correct "before" pointer to locks_unlink_lock in generic_add_lease

Merge remote-tracking branches 'spi/fix/au1550', 'spi/fix/davinci', 'spi/fix/doc', 'spi/fix/dw', 'spi/fix/omap-mcspi', 'spi/fix/pxa2xx', 'spi/fix/rockchip' and 'spi/fix/rspi' into spi-linus

Pull x86 fixes from Peter Anvin:
 "One patch to avoid assigning interrupts we don't actually have on
  non-PC platforms, and two patches that addresses bugs in the new
  IOAPIC assignment code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, irq, PCI: Keep IRQ assignment for runtime power management
  x86: irq: Fix bug in setting IOAPIC pin attributes
  x86: Fix non-PC platform kernel crash on boot due to NULL dereference

Pull ACPI and power management fixes from Rafael Wysocki:

 - Fix for an ACPI regression related to the handling of fixed events
   that caused netlink routines to be (incorrectly) run in interrupt
   context from Lan Tianyu

 - Fix for an ACPI EC driver regression on Acer Aspire V5-573G that
   caused AC/battery plug/unplug and video brightness change
   notifications to be delayed on that machine from Lv Zheng

 - Fix for an ACPI device enumeration regression that caused ACPI driver
   probe to fail for some devices where it succeeded before (Rafael J
   Wysocki)

 - intel_pstate driver fix to prevent it from printing an information
   message for every CPU in the system on every boot from Andi Kleen

 - s5pv210 cpufreq driver fix to remove an __init annotation from a
   routine that in fact can be called at any time after init too from
   Mark Brown

 - New Intel Braswell device ID for the ACPI LPSS (Low-Power Subsystem)
   driver from Alan Cox

 - New Intel Braswell CPU ID for intel_pstate from Mika Westerberg

* tag 'pm+acpi-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: s5pv210: Remove spurious __init annotation
  cpufreq: intel_pstate: Add CPU ID for Braswell processor
  intel_pstate: Turn per cpu printk into pr_debug
  ACPI / LPSS: Add ACPI IDs for Intel Braswell
  ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC
  ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
  ACPI: Run fixed event device notifications in process context
  ACPI / scan: Allow ACPI drivers to bind to PNP device objects