David Vrabel says:

====================
xen-netfront: refactor making Tx requests

As netfront as evolved to handle different sorts of skbs the code to
fill a Tx requests has been copy and pasted several times.  The series
refactors this and a few other areas.

The first patch is to a Xen header but this can be merged via
net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate all the duplicate code for making Tx requests by
consolidating them into a single xennet_make_one_txreq() function.

xennet_make_one_txreq() and xennet_make_txreqs() work with pages and
offsets so it will be easier to make netfront handle highmem frags in
the future.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A function to count the number of slots an skb needs is more useful
than one that counts the slots needed for only the frags.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pfn_to_mfn(page_to_pfn(p)) is a common use case so add a generic
helper for it.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each per bucket lock covers a configurable number of buckets. While
shrinking, two buckets in the old table contain entries for a single
bucket in the new table. We need to lock down both while linking.
Check if they are protected by different locks to avoid a recursive
lock.

Fixes: 97defe1e ("rhashtable: Per bucket locks & deferred expansion/shrinking")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc code implicitly considers skb->protocol even in case of accelerated
vlan paths and expects vlan protocol type here. However, on rx path,
if the vlan header was already stripped, skb->protocol contains value
of next header. Similar situation is on tx path.

So for skbs that use skb->vlan_tci for tagging, use skb->vlan_proto instead.
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removes some functions that are not used anywhere:
channel_to_vpivci() query_tx_channel_config() rx_disabled_handler()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the function aal5_spacefor() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f2f9800d "tipc: make tipc node table aware of net
namespace" has added a dereference of sock->sk before making sure it's
not NULL, which makes releasing a tipc socket NULL pointer dereference
for sockets that are not fully initialized.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the rx packet length check in the sunvnet driver to allow
for a TSO max packet length greater than the LDC channel negotiated MTU.
These are negotiated separately and there is no requirement that
port->tsolen be less than port->rmtu, but if it isn't, it'll drop packets
with rx length errors.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not all architectures are able to call __builtin_return_address().
On ARM, the mISDN code produces this warning:

hardware/mISDN/w6692.c: In function 'w6692_dctrl':
hardware/mISDN/w6692.c:1181:75: warning: unsupported argument to '__builtin_return_address'
  pr_debug("%s: %s dev(%d) open from %p\n", card->name, __func__,
                                                                           ^
hardware/mISDN/mISDNipac.c: In function 'open_dchannel':
hardware/mISDN/mISDNipac.c:759:75: warning: unsupported argument to '__builtin_return_address'
  pr_debug("%s: %s dev(%d) open from %p\n", isac->name, __func__,
                                                                           ^

In a lot of cases, this is relatively easy to work around by
passing the value of __builtin_return_address(0) from the
callers into the functions that want it. One exception is
the indirect 'open' function call in struct isac_hw. While it
would be possible to fix this as well, this patch only addresses
the other callers properly and lets this one return the direct
parent function, which should be good enough.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The return type of find_first_bit() is architecture specific,
on ARM it is 'unsigned int', while the asm-generic code used
on x86 and a lot of other architectures returns 'unsigned long'.

When building the mlx5 driver on ARM, we get a warning about
this:

infiniband/hw/mlx5/mem.c: In function 'mlx5_ib_cont_pages':
infiniband/hw/mlx5/mem.c:84:143: warning: comparison of distinct pointer types lacks a cast
     m = min(m, find_first_bit(&tmp, sizeof(tmp)));

This patch changes the driver to use min_t to make it behave
the same way on all architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mlx5 driver passes a string pointer in through a 'u64' variable,
which on 32-bit machines causes a build warning:

drivers/net/ethernet/mellanox/mlx5/core/debugfs.c: In function 'qp_read_field':
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c:303:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]

The code is in fact safe, so we can shut up the warning by adding
extra type casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rocker driver tries to assign a pointer to a 64-bit integer
and then back to a pointer. This is safe on all architectures,
but causes a compiler warning when pointers are shorter than
64-bit:

rocker/rocker.c: In function 'rocker_desc_cookie_ptr_get':
rocker/rocker.c:809:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  return (void *) desc_info->desc->cookie;
         ^

This adds another cast to uintptr_t to tell the compiler
that it's safe.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removing old hard-wired initialization code in the driver, which is no longer
used. Also deprecating few module parameters.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the redundant timer defined in tipc_sock structure, instead we
can directly reuse the sk_timer defined in sock structure.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a bug in xgmac_mdio_read when clear the bit MDIO_STAT_ENC,
which '&' is missed in 'mdio_stat &= ~MDIO_STAT_ENC'.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/bridge/br_netlink.c: In function ‘br_fill_ifinfo’:
net/bridge/br_netlink.c:146:32: warning: ‘vid_range_flags’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  err = br_fill_ifvlaninfo_range(skb, vid_range_start,
                                ^
net/bridge/br_netlink.c:108:6: note: ‘vid_range_flags’ was declared here
  u16 vid_range_flags;
Reported-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Patch 3b50d902 ("ipv6: fix redefinition of in6_pktinfo ...")
fixed a libc compatibility issue in ipv6 structure definitions
as described in include/uapi/linux/libc-compat.h.

It relies on including linux/in6.h to include libc-compat.h itself.
Include that file directly to clearly communicate the dependency
(libc-compat.h: "This include must be as early as possible").
Signed-off-by: Willem de Bruijn <willemb@google.com>

----

As discussed in http://patchwork.ozlabs.org/patch/427384/Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-01-13

This series contains updates to i40e and i40evf.

Mitch provides a fix for i40e to move the call to pci_disable_sriov() so
that it is called earlier to ensure that the PF driver won't free VF
resources before the VF remove routine can complete.  Also cleans up
redundant and duplicate code in the i40evf.  Refactors the i40evf
shutdown code and let the watchdog take care of shutting things down.
Fix a possible memory leak, if we are using VLANs and the communication
with the PF fail during shutdown.  On some versions of the firmware, the
VF admin send queue may become stalled.  In this case, the easiest
solution is to place another descriptor on the queue and the firmware
will then process both requests.

Greg adds a warning when the NPAR enabled partitions detected a link speed
less than 10 Gpbs.

Vasu removes redundant VN2VN MAC address which were already added by
the FCoE stack.

Shannon adds code to find how many partitions there are per port and
what is the current partition_id when in NPAR mode.  In multifunction
mode, make sure we only allow SR/IOV on the master PF of a port and
only allow partition 1 to set WoL, speed and flow control.

Kamil adds code to read the PBA block from shadow RAM and returns
the part number in a string format.

Catherine provides a fix to check if link state and link speed has
changed before exiting link event

v2: remove un-needed {} in patch #3 of the series based on feedback from
    Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure we only allow SR/IOV on the master PF of a port in multifunction
mode.  This should be the case anyway based on the num_vfs configured in
the NVM, but this will help make sure there's no question.  If we're not
in multifunction mode the partition_id will always be 1.

Change-ID: I8b2592366fe6782f15301bde2ebd1d4da240109d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were only checking if the link up state had changed,
and if it hadn't exiting the link event routine early. We should
also check if speed has changed, and if it has, stay and finish
processing the link event.

Change-ID: I9c8e0991b3f0279108a7858898c3c5ce0a9856b8
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When in multi-function mode, e.g. Dell's NPAR, only partition 1
of each MAC is allowed to set WoL, speed, and flow control.

Change-ID: I87a9debc7479361c55a71f0120294ea319f23588
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Function will read PBA Block from Shadow RAM and return it in a string format.

Change-ID: I4ee7059f6e21bd0eba38687da15e772e0b4ab36e
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When in NPAR mode the driver instance might be controlling the base
partition or one of the other "fake" PFs.  There are some things that
can only be done by the base partition, aka partition_id 1.  This code
does a bit of work to find how many partitions are there per port and
what is the current partition_id.

Change-ID: Iba427f020a1983d02147d86f121b3627e20ee21d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

These mac address already added by FCoE stack above netdev,
therefore adding them here is redundant.

Change-ID: Ia5b59f426f57efd20f8945f7c6cc5d741fbe06e5
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

NPAR enabled partitions should warn the user when detected link speed is
less than 10Gpbs.

Change-ID: I7728bb8ce279bf0f4f755d78d7071074a4eb5f69
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

On some versions of the firmware, the VF admin send queue may become
stalled. In this case, the easiest solution is to just place another
descriptor on the queue; the firmware will then process both requests.

The early init code already accounts for this, but the runtime code does
not. In the watchdog task, check for the stall condition, and if it's
found, send our API version to the PF. When the PF replies, just ignore
the reply.

Change-ID: I380d78185a4f284d649c44d263e648afc9b4d50c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't enable vector 0 in the ISR, just schedule the adminq task and let
it enable the vector. This prevents the task from being called
reentrantly. Make sure that the vector is enabled on all exit paths of
the adminq task, including error exits.

Change-ID: I53f3d14f91ed7a9e90291ea41c681122a5eca5b5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There is always a possibility that MSI-X interrupts can get lost. To
keep this problem from stalling the driver, we fire all of our MSI-X
vectors during the watchdog routine. However, we should not fire the
traffic vectors when the interface is closed. In this case, just fire
vector 0, which is used for admin queue events.

As a result, we do not enable the interrupt cause for vector 0. This
can cause the admin queue handler to be called reentrantly, which
causes a scary "critical section violation" message to be logged,
even though no real damage is done.

Change-ID: Ic43a5184708ab2cb9a23fca7dedd808a46717795
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If we're using VLANs and communications with the PF fail during
shutdown, we will leak memory because not all of the VLAN filters will
be removed. To eliminate this possibility, go through the list again
right before the module is removed and delete any leftover entries.

Change-ID: Id3b5315c47ca0a61ae123a96ff345d010bc41aed
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If the VF driver is running in the host, the shutdown code is completely
broken. We cannot wait in our down routine for the PF to respond to our
requests, as its admin queue task will never run while we hold the lock.

Instead, we schedule operations, then let the watchdog take care of
shutting things down. If the driver is being removed, then wait in the
remove routine until the watchdog is done before continuing.

Change-ID: I93a58d17389e8d6b58f21e430b56ed7b4590b2c5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

version.h inclusion is not necessary as detected by versioncheck.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These messages may be triggered during normal init of the driver if the
PF or FW take a long time to respond. There's nothing really wrong, so
don't freak people out logging messages.

If the communication channel really is dead, then we'll retry a few
times and give up. This will log a different more scary message that
should cause consternation. This allows the user to more easily detect a
genuine failure.

Change-ID: I6e2b758d4234a3a09c1015c82c8f2442a697cbdb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

These functions are redundant and duplicate functionality found in
i40evf_free_all_[tx|rx]_resources.

Change-ID: Ia199908926d7a1a4b8247f75f89b5da24c9b149c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If VF drivers are loaded in the host OS, the call to pci_disable_sriov()
will cause these drivers' remove routines to be called. If the PF driver
has already freed VF resources before this happens, then the VF remove
routine can't properly communicate with the PF driver causing all sorts
of mayhem and error messages and hurt feelings.

To fix this, we move the call to pci_disable_sriov() up to the top of
the function and let it complete before freeing any VF resources.

Change-ID: I397c3997a00f6408e32b7735273911e499600236
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

With TLP, the peer may reply to a probe with an
ACK+D-SACK, with ack value set to tlp_high_seq. In the current code,
such ACK+DSACK will be missed and only at next, higher ack will the TLP
episode be considered done. Since the DSACK is not present anymore,
this will cost a cwnd reduction.

This patch ensures that this scenario does not cause a cwnd reduction, since
receiving an ACK+DSACK indicates that both the initial segment and the probe
have been received by the peer.

The following packetdrill test, from Neal Cardwell, validates this patch:

// Establish a connection.
0     socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0     setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0    bind(3, ..., ...) = 0
+0    listen(3, 1) = 0

+0    < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0    > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 6>
+.020 < . 1:1(0) ack 1 win 257
+0    accept(3, ..., ...) = 4

// Send 1 packet.
+0    write(4, ..., 1000) = 1000
+0    > P. 1:1001(1000) ack 1

// Loss probe retransmission.
// packets_out == 1 => schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
// In this case, this means: 1.5*RTT + 200ms = 230ms
+.230 > P. 1:1001(1000) ack 1
+0    %{ assert tcpi_snd_cwnd == 10 }%

// Receiver ACKs at tlp_high_seq with a DSACK,
// indicating they received the original packet and probe.
+.020 < . 1:1(0) ack 1001 win 257 <sack 1:1001,nop,nop>
+0    %{ assert tcpi_snd_cwnd == 10 }%

// Send another packet.
+0    write(4, ..., 1000) = 1000
+0    > P. 1001:2001(1000) ack 1

// Receiver ACKs above tlp_high_seq, which should end the TLP episode
// if we haven't already. We should not reduce cwnd.
+.020 < . 1:1(0) ack 2001 win 257
+0    %{ assert tcpi_snd_cwnd == 10, tcpi_snd_cwnd }%

Credits:
-Gregory helped in finding that tcp_process_tlp_ack was where the cwnd
got reduced in our MPTCP tests.
-Neal wrote the packetdrill test above
-Yuchung reworked the patch to make it more readable.

Cc: Gregory Detal <gregory.detal@uclouvain.be>
Cc: Nandita Dukkipati <nanditad@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Sébastien Barré <sebastien.barre@uclouvain.be>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>