- 26 Sep, 2016 24 commits
-
-
Wolfram Sang authored
card_busy is only used/tested on SDHI for R-Car Gen2 and later. Move it to the SDHI driver, so we can then activate it conditionally depending on the SDHI type. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Michael Weiser authored
The sunxi-mmc driver does not take into account the processor may be big endian when writing the DMA descriptors. This causes cards not to be detected when running a big-endian kernel. Change the descriptors for IDMA to use __le32 and ensure they are suitably swapped before writing. Tested successfully on the Cubieboard2. Signed-off-by:
Michael Weiser <michael.weiser@gmx.de> Acked-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Chen-Yu Tsai <wens@csie.org> Cc: linux-mmc@vger.kernel.org Signed-off-by:
-
Jean-Francois Moine authored
clk_round_rate() may return an error. Check it. Signed-off-by:
Jean-Francois Moine <moinejf@free.fr> Acked-by:
-
Douglas Anderson authored
PHY intended to be used with the Arasan SDHCI 5.1 controller has trouble turning on when the card clock is slow or off. Strangely these problems appear to show up consistently on some boards while other boards work fine, but on the boards where it shows up the problem reproduces 100% of the time and is quite consistent in its behavior. These problems can be fixed by always making sure that we power on the PHY (and turn on its DLL) when the card clock is faster than about 50 MHz. Once on, we need to make sure that we never power down the PHY / turn off its DLL until the clock is faster again. We'll add logic for handling this into the sdhci-of-arasan driver. Note that right now the only user of a PHY in the sdhci-of-arasan driver is arasan,sdhci-5.1. It's presumed that all arasan,sdhci-5.1 PHY implementations need this workaround, so the logic is only contingent on having a PHY to control. If future Arasan controllers don't have this problem we can add code to decide if we want this flow or not. Also note that we check for slow clocks by checking for <= 400 kHz rather than checking for 50 MHz. This keeps things the most consistent and also means we can power the PHY on at max speed (where the DLL will lock fastest). Presumably anyone who intends to run with a card clock of < 50 MHz and > 400 kHz will be running on a device where this problem is fixed anyway. I believe this brings some resolution to the problems reported before. See the commit 6fc09244 ("mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes"). Signed-off-by:
Douglas Anderson <dianders@chromium.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
-
Christopher Freeman authored
wait_event_interruptible_timeout() will return early if the blocked process receives a signal, causing the driver to abort the tuning procedure and possibly leaving the controller in a bad state. Since the tuning command is expected to complete quickly (<50ms) and we've set a timeout, use wait_event_timeout() instead. Signed-off-by:
Christopher Freeman <cfreeman@nvidia.com> Tested-by:
Robert Foss <robert.foss@collabora.com> Signed-off-by:
Benson Leung <bleung@chromium.org> Acked-by:
-
Haibo Chen authored
i.MX USDHC Reference Manual has a mistake, for the register SYS_CTRL, the DTOCV(bit 19~16) means the data timeout counter value. When DTOCV is set to 0xF, it means SDCLK << 29, not SDCLK << 28. Signed-off-by:
Haibo Chen <haibo.chen@nxp.com> Acked-by:
Dong Aisheng <aisheng.dong@nxp.com> Acked-by:
-
Haibo Chen authored
Now, when call esdhc_set_timeout() to set the data timeout counter value, IPP_RST_N(bit 23) is wrongly affected. This patch add a mask to avoid this. Signed-off-by:
-
Markus Elfring authored
The field "owner" is set by core. Thus delete an extra initialisation. Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Acked-by:
-
Uri Yanai authored
The SD Status register contains several important fields related to the SD Card proprietary features. Those fields may be used by user space applications for vendor specific usage. None of those fields are exported today by the driver to user space. In this patch, we are reading the SD Status register and exporting (using MMC_DEV_ATTR) the SD Status register to the user space. Signed-off-by:
Uri Yanai <uri.yanai@sandisk.com> Signed-off-by:
-
Wolfram Sang authored
kmalloc will print enough information in case of failure. Signed-off-by:
Wolfram Sang <wsa-dev@sang-engineering.com> Signed-off-by:
-
Julia Lawall authored
Use of_property_read_bool to check for the existence of a property. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression e1,e2; statement S2,S1; @@ - if (of_get_property(e1,e2,NULL)) + if (of_property_read_bool(e1,e2)) S1 else S2 // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Acked-by:
-
Ben Dooks authored
The core MMC code adds two (optional) regulator properites that drivers should use to get their supplies. This is not documented anywhere so add information on it. Signed-off-by:
Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by:
-
Wei Yongjun authored
In clk_set_rate() or clk_prepare_enable() error handling case, the error return code ret is not set, so sdhci_bcm_kona_probe() return 0 in those error cases. Signed-off-by:
Wei Yongjun <weiyj.lk@gmail.com> Acked-by:
Ray Jui <ray.jui@broadcom.com> Acked-by:
-
Nicholas Mc Guire authored
wait_for_completion_timeout_interruptible returns long not unsigned long so dma_time, which is used exclusively here, is changed to long. Fixes: 1b66e94e ("mmc: moxart: Add MOXA ART SD/MMC driver") Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by:
-
Hans de Goede authored
Some devices need a while to boot their firmware after providing clks / de-asserting resets before they are ready to receive sdio commands. This commits adds a post-power-on-delay-ms devicetree property to mmc-pwrseq-simple for use with such devices. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Hans de Goede authored
On some boards (android tablets) different batches use different sdio wifi modules. This is not a problem since mmc/sdio is an enumerable bus, so we only need to describe and activate the mmc controller in dt and then the kernel will automatically load the right driver. Sometimes it is useful to specify certain ethernet properties for these "unknown" sdio devices, specifically we want the boot-loader to be able to set "local-mac-address" as some of these sdio wifi modules come without an eeprom / without a factory programmed mac address. Since the exact device is unknown (differs per batch) we cannot use a wifi-chip specific compatible, thus sometimes it is desirable to have a mmc function node, without having to make up an otherwise unused compatible for the node, so make the compatible property optional. Cc: Arnd Bergmann <arnd@arndb.de> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Hans de Goede authored
Use the new sun7i-a20-mmc compatible for the mmc controllers on sun7i and newer. Signed-off-by:
-
Hans de Goede authored
It turns out that sun4i (A10) and sun5i (A13 & co) do not have sample clocks, so add a new sun7i-a20-mmc compatible and do not try to use sample clocks on sun4i / sun5i. Since sun4i / sun5i do not have sample clocks, they cannot (reliably) do DDR rates, so only set MMC_CAP_1_8V_DDR when we do have sample clks. Note this patch leaves the clk_prepare_enable() / clk_disable_unprepare() calls to the sample clks as-is, without adding checks for them being NULL. All the clk_foo calls accept a NULL clk and will return success when called with a NULL clk. Signed-off-by:
-
Hans de Goede authored
Add a sunxi_mmc_clk_set_phase() helper function. Signed-off-by:
-
Hans de Goede authored
Create a struct to hold the various model / compatible string dependend settings. Signed-off-by:
-
Hans de Goede authored
When support for the sample clks was added calls to prepare_enable were added to the probe path, but matching calls to disable_unprepare were forgotten in the remove path, this fixes this. Signed-off-by:
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-traceLinus Torvalds authored
Pull tracefs fixes from Steven Rostedt: "Al Viro has been looking at the tracefs code, and has pointed out some issues. This contains one fix by me and one by Al. I'm sure that he'll come up with more but for now I tested these patches and they don't appear to have any negative impact on tracing" * tag 'trace-v4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: fix memory leaks in tracing_buffers_splice_read() tracing: Move mutex to protect against resetting of seq data
-
Dave Chinner authored
When building XFS with -Werror, it now fails with: include/linux/pagemap.h: In function 'fault_in_multipages_readable': include/linux/pagemap.h:602:16: error: variable 'c' set but not used [-Werror=unused-but-set-variable] volatile char c; ^ This is a regression caused by commit e23d4159 ("fix fault_in_multipages_...() on architectures with no-op access_ok()"). Fix it by re-adding the "(void)c" trick taht was previously used to make the compiler think the variable is used. Signed-off-by:Dave Chinner <dchinner@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
- 25 Sep, 2016 7 commits
-
-
Lorenzo Stoakes authored
The NUMA balancing logic uses an arch-specific PROT_NONE page table flag defined by pte_protnone() or pmd_protnone() to mark PTEs or huge page PMDs respectively as requiring balancing upon a subsequent page fault. User-defined PROT_NONE memory regions which also have this flag set will not normally invoke the NUMA balancing code as do_page_fault() will send a segfault to the process before handle_mm_fault() is even called. However if access_remote_vm() is invoked to access a PROT_NONE region of memory, handle_mm_fault() is called via faultin_page() and __get_user_pages() without any access checks being performed, meaning the NUMA balancing logic is incorrectly invoked on a non-NUMA memory region. A simple means of triggering this problem is to access PROT_NONE mmap'd memory using /proc/self/mem which reliably results in the NUMA handling functions being invoked when CONFIG_NUMA_BALANCING is set. This issue was reported in bugzilla (issue 99101) which includes some simple repro code. There are BUG_ON() checks in do_numa_page() and do_huge_pmd_numa_page() added at commit c0e7cad9 to avoid accidentally provoking strange behaviour by attempting to apply NUMA balancing to pages that are in fact PROT_NONE. The BUG_ON()'s are consistently triggered by the repro. This patch moves the PROT_NONE check into mm/memory.c rather than invoking BUG_ON() as faulting in these pages via faultin_page() is a valid reason for reaching the NUMA check with the PROT_NONE page table flag set and is therefore not always a bug. Link: https://bugzilla.kernel.org/show_bug.cgi?id=99101Reported-by:
Trevor Saunders <tbsaunde@tbsaunde.org> Signed-off-by:
Lorenzo Stoakes <lstoakes@gmail.com> Acked-by:
Rik van Riel <riel@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by:
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS fixes from Ralf Baechle: "A round of 4.8 fixes: MIPS generic code: - Add a missing ".set pop" in an early commit - Fix memory regions reaching top of physical - MAAR: Fix address alignment - vDSO: Fix Malta EVA mapping to vDSO page structs - uprobes: fix incorrect uprobe brk handling - uprobes: select HAVE_REGS_AND_STACK_ACCESS_API - Avoid a BUG warning during PR_SET_FP_MODE prctl - SMP: Fix possibility of deadlock when bringing CPUs online - R6: Remove compact branch policy Kconfig entries - Fix size calc when avoiding IPIs for small icache flushes - Fix pre-r6 emulation FPU initialisation - Fix delay slot emulation count in debugfs ATH79: - Fix test for error return of clk_register_fixed_factor. Octeon: - Fix kernel header to work for VDSO build. - Fix initialization of platform device probing. paravirt: - Fix undefined reference to smp_bootstrap" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: Fix delay slot emulation count in debugfs MIPS: SMP: Fix possibility of deadlock when bringing CPUs online MIPS: Fix pre-r6 emulation FPU initialisation MIPS: vDSO: Fix Malta EVA mapping to vDSO page structs MIPS: Select HAVE_REGS_AND_STACK_ACCESS_API MIPS: Octeon: Fix platform bus probing MIPS: Octeon: mangle-port: fix build failure with VDSO code MIPS: Avoid a BUG warning during prctl(PR_SET_FP_MODE, ...) MIPS: c-r4k: Fix size calc when avoiding IPIs for small icache flushes MIPS: Add a missing ".set pop" in an early commit MIPS: paravirt: Fix undefined reference to smp_bootstrap MIPS: Remove compact branch policy Kconfig entries MIPS: MAAR: Fix address alignment MIPS: Fix memory regions reaching top of physical MIPS: uprobes: fix incorrect uprobe brk handling MIPS: ath79: Fix test for error return of clk_register_fixed_factor().
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull one more powerpc fix from Michael Ellerman: "powernv/pci: Fix m64 checks for SR-IOV and window alignment from Russell Currey" * tag 'powerpc-4.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/powernv/pci: Fix m64 checks for SR-IOV and window alignment
-
Linus Torvalds authored
The fixes to the radix tree test suite show that the multi-order case is broken. The basic reason is that the radix tree code uses tagged pointers with the "internal" bit in the low bits, and calculating the pointer indices was supposed to mask off those bits. But gcc will notice that we then use the index to re-create the pointer, and will avoid doing the arithmetic and use the tagged pointer directly. This cleans the code up, using the existing is_sibling_entry() helper to validate the sibling pointer range (instead of open-coding it), and using entry_to_node() to mask off the low tag bit from the pointer. And once you do that, you might as well just use the now cleaned-up pointer directly. [ Side note: the multi-order code isn't actually ever used in the kernel right now, and the only reason I didn't just delete all that code is that Kirill Shutemov piped up and said: "Well, my ext4-with-huge-pages patchset[1] uses multi-order entries. It also converts shmem-with-huge-pages and hugetlb to them. I'm okay with converting it to other mechanism, but I need something. (I looked into Konstantin's RFC patchset[2]. It looks okay, but I don't feel myself qualified to review it as I don't know much about radix-tree internals.)" [1] http://lkml.kernel.org/r/20160915115523.29737-1-kirill.shutemov@linux.intel.com [2] http://lkml.kernel.org/r/147230727479.9957.1087787722571077339.stgit@zurg ] Reported-by:Matthew Wilcox <mawilcox@microsoft.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Cedric Blancher <cedric.blancher@gmail.com> Signed-off-by:
-
Matthew Wilcox authored
When we replace a multiorder entry, check that all indices reflect the new value. Also, compile the test suite with -O2, which shows other problems with the code due to some dodgy pointer operations in the radix tree code. Signed-off-by:
-
Al Viro authored
Cc: stable@vger.kernel.org Signed-off-by:Al Viro <viro@zeniv.linux.org.uk>
-
Steven Rostedt (Red Hat) authored
The iter->seq can be reset outside the protection of the mutex. So can reading of user data. Move the mutex up to the beginning of the function. Fixes: d7350c3f ("tracing/core: make the read callbacks reentrants") Cc: stable@vger.kernel.org # 2.6.30+ Reported-by:
Steven Rostedt <rostedt@goodmis.org>
-
- 24 Sep, 2016 9 commits
-
-
Paul Burton authored
Commit 432c6bac ("MIPS: Use per-mm page to execute branch delay slot instructions") accidentally removed use of the MIPS_FPU_EMU_INC_STATS macro from do_dsemulret, leading to the ds_emul file in debugfs always returning zero even though we perform delay slot emulations. Fix this by re-adding the use of the MIPS_FPU_EMU_INC_STATS macro. Signed-off-by:
Paul Burton <paul.burton@imgtec.com> Fixes: 432c6bac ("MIPS: Use per-mm page to execute branch delay slot instructions") Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/14301/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org>
-
Matt Redfearn authored
This patch fixes the possibility of a deadlock when bringing up secondary CPUs. The deadlock occurs because the set_cpu_online() is called before synchronise_count_slave(). This can cause a deadlock if the boot CPU, having scheduled another thread, attempts to send an IPI to the secondary CPU, which it sees has been marked online. The secondary is blocked in synchronise_count_slave() waiting for the boot CPU to enter synchronise_count_master(), but the boot cpu is blocked in smp_call_function_many() waiting for the secondary to respond to it's IPI request. Fix this by marking the CPU online in cpu_callin_map and synchronising counters before declaring the CPU online and calculating the maps for IPIs. Signed-off-by:
Matt Redfearn <matt.redfearn@imgtec.com> Reported-by:
Justin Chen <justinpopo6@gmail.com> Tested-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Thomas Gleixner: "Three fixlets for perf: - add a missing NULL pointer check in the intel BTS driver - make BTS an exclusive PMU because BTS can only handle one event at a time - ensure that exclusive events are limited to one PMU so that several exclusive events can be scheduled on different PMU instances" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/core: Limit matching exclusive events to one PMU perf/x86/intel/bts: Make it an exclusive PMU perf/x86/intel/bts: Make sure debug store is valid -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull locking fixes from Thomas Gleixner: "Two smallish fixes: - use the proper asm constraint in the Super-H atomic_fetch_ops - a trivial typo fix in the Kconfig help text" * 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: locking/hung_task: Fix typo in CONFIG_DETECT_HUNG_TASK help text locking/atomic, arch/sh: Fix ATOMIC_FETCH_OP()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull EFI fixes from Thomas Gleixner: "Two fixes for EFI/PAT: - a 32bit overflow bug in the PAT code which was unearthed by the large EFI mappings - prevent a boot hang on large systems when EFI mixed mode is enabled but not used" * 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/efi: Only map RAM into EFI page tables if in mixed-mode x86/mm/pat: Prevent hang during boot when mapping pages -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixes from Thomas Gleixner: "Three fixes for irq core and irq chip drivers: - Do not set the irq type if type is NONE. Fixes a boot regression on various SoCs - Use the proper cpu for setting up the GIC target list. Discovered by the cpumask debugging code. - A rather large fix for the MIPS-GIC so per cpu local interrupts work again. This was discovered late because the code falls back to slower timers which use normal device interrupts" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/mips-gic: Fix local interrupts irqchip/gicv3: Silence noisy DEBUG_PER_CPU_MAPS warning genirq: Skip chained interrupt trigger setup if type is IRQ_TYPE_NONE -
Linus Torvalds authored
Merge VM fixes from High Dickins: "I get the impression that Andrew is away or busy at the moment, so I'm going to send you three independent uncontroversial little mm fixes directly - though none is strictly a 4.8 regression fix. - shmem: fix tmpfs to handle the huge= option properly from Toshi Kani is a one-liner to fix a major embarrassment in 4.8's hugepages on tmpfs feature: although Hillf pointed it out in June, somehow both Kirill and I repeatedly dropped the ball on this one. You might wonder if the feature got tested at all with that bug in: yes, it did, but for wider testing coverage, Kirill and I had each relied too much on an override which bypasses that condition. - huge tmpfs: fix Committed_AS leak just a run-of-the-mill accounting fix in the same feature. - mm: delete unnecessary and unsafe init_tlb_ubc() is an unrelated fix to 4.3's TLB flush batching in reclaim: the bug would be rare, and none of us will be shamed if this one misses 4.8; but it got such a quick ack from Mel today that I'm inclined to offer it along with the first two" * emailed patches from Hugh Dickins <hughd@google.com>: mm: delete unnecessary and unsafe init_tlb_ubc() huge tmpfs: fix Committed_AS leak shmem: fix tmpfs to handle the huge= option properly -
Hugh Dickins authored
init_tlb_ubc() looked unnecessary to me: tlb_ubc is statically initialized with zeroes in the init_task, and copied from parent to child while it is quiescent in arch_dup_task_struct(); so I went to delete it. But inserted temporary debug WARN_ONs in place of init_tlb_ubc() to check that it was always empty at that point, and found them firing: because memcg reclaim can recurse into global reclaim (when allocating biosets for swapout in my case), and arrive back at the init_tlb_ubc() in shrink_node_memcg(). Resetting tlb_ubc.flush_required at that point is wrong: if the upper level needs a deferred TLB flush, but the lower level turns out not to, we miss a TLB flush. But fortunately, that's the only part of the protocol that does not nest: with the initialization removed, cpumask collects bits from upper and lower levels, and flushes TLB when needed. Fixes: 72b252ae ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages") Signed-off-by:
Hugh Dickins <hughd@google.com> Acked-by:
Mel Gorman <mgorman@techsingularity.net> Cc: stable@vger.kernel.org # 4.3+ Signed-off-by:
-
Hugh Dickins authored
Under swapping load on huge tmpfs, /proc/meminfo's Committed_AS grows bigger and bigger: just a cosmetic issue for most users, but disabling for those who run without overcommit (/proc/sys/vm/overcommit_memory 2). shmem_uncharge() was forgetting to unaccount __vm_enough_memory's charge, and shmem_charge() was forgetting it on the filesystem-full error path. Fixes: 800d8c63 ("shmem: add huge pages support") Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
-
